Page is loading ...
Instruction
Sheet
When Performance Matters.
™
WARNING
If incorrectly used, this machine can cause severe injury. Those who use
and maintain this machine should be trained in its proper use, warned of its
dangers and should read the entire manual before attempting to set up,
operate, adjust, or service the machine.
19
17
18
13
6
5
9
15
16
7
8
10
4
3
11
1 - INCLUDES ITEMS 3 - 16
2812002
Turf Groomer™
1/4” Spacing
22” R.H. Groomer Product Number 67911
22” L.H. Groomer Product Number 67912
1/2” Spacing
22” R.H. Groomer Product Number 67913
22” L.H. Groomer Product Number 67914
18” R.H. Groomer Product Number 67926
2
This product is used on 5.0” diameter reels on GKIV™,
GKV™, G-Plex® and Fairway mowers.
1.1 PREPARATION __________________________________________________________________________________
1. Park the mower on a flat and level surface, fully lower the
cutting units to the ground, engage the parking brake,
turn the ignition switch to the OFF position and remove
key.
a. Wait for all movement to stop before making any
adjustments or modifications.
b. Take this opportunity to thoroughly inspect the
equipment and perform other maintenance.
c. For all steps, refer to the Parts List for part
identification.
d. Although the figures show installing a right hand
Groomer, the assembly process is identical for a left
hand Groomer.
2. The turf groomer has been pre-assembled into five sub
assemblies and a bag of parts. [See Figure 1]
a. The driven sub assembly (A) is assembled to the
motor end of the reel.
b. The drive sub assembly (B) is assembled to the
counterweight end of the reel.
c. 22” Groomers: The other sub assemblies consist of
a blade assembly (C), roller (D) and clutch knob (E).
d. 18” Groomers: The other subassemblies consist of
a blade assembly (C), roller (D) and pulley assembly
(I).
3. To help in the assembly process and prevent confusion
between right hand and left hand units, completely install
each Turf Groomer before starting on the next reel.
a. Open each carton to inspect and familiarize yourself
with the contents.
b. Keep all components in original carton until ready for
assembly.
4. Remove the reels from the mower, following directions
given in the mower’s manuals.
5. Remove the lift yoke, front roller and height adjust
brackets from each reel. Retain for future use.
6. Determine if a right hand or a left hand Groomer is to be
installed for each reel. Move one reel and corresponding
groomer assembly to workbench. [See Figure 2]
Figure 1
Figure 2
CAUTION
Read the operator’s manual and become familiar with
the controls and proper use of the equipment.
Stay alert for potential hazards and follow all safety
precautions. Read all instructions completely and
make sure you understand them before proceeding
with the assembly.
!
WARNING
Before you clean, adjust, or repair this equipment,
disengage all drives, lower cutting units to the ground,
engage parking brake, stop engine, remove key from
switch and disconnect Negative (BLACK) battery cable to
prevent injuries.
!
A
B
C
D
E
I
Right Hand Groomer Required
Left Hand Groomer Required
Motor
End
Motor
End
Front
Litho in U.S.A. 9-2008
3
1.2 PRE-ASSEMBLY _________________________________________________________________________________
1. Remove 1/4” hardware (F) and cover / counterweight (G)
from non-motor end of reel.
2. Block the reel with a piece of wood, and remove 3/8”
hardware (H) and spacer (Z) from the end of reel shaft.
Figure 3
Figure 4
3. Check the reel shaft nut (K) to insure it is positioned
properly. [See Figure 4]
a. 22” Groomers: Obtain drive pulley (J) from bag of
parts.
a. 18” Groomers: Obtain pulley spacer (AD) from bag
of parts.
b. Slide pulley (J) or spacer (AD) onto the reel shaft.
c. The pulley or spacer should be up against the
shoulder of the shaft with a 0.01 to 0.02 in. (.25 to .5
mm) gap between the pulley bearing and nut (K).
d. If necessary, turn nut (K) until proper gap is obtained.
e. Remove pulley or spacer and return to bag of parts.
4. Determine how many shims will be required for driven
sub assembly (A).[See Figure 5]
a. Obtain driven assembly (A) and four 0.02 in. thick
shims (L) from bag of parts.
b. Slide driven assembly (A) onto the motor end bearing
housing and hold it squarely and tightly against the
housing.
c. Determine how many shims (L), if any, fit between
the height adjuster mounting block (M) and driven
assembly. Write number of shims down for assembly
purposes.
d. Remove driven assembly (A) and return shims to bag
of parts.
5. If you are installing the Turf Groomer on an LF series
mower, move the height adjust pivot (N) from the bottom
hole to the top hole of both driven assembly (A) and drive
assembly (B). [See Figure 6]
Figure 5
Figure 6
NOTE:
The bottom hole is for GKIV, GKV and G-Plex units, and
the upper hole is for Fairway units. Groomer is shipped with pivot
(N) installed in bottom hole.
6. If you are installing the Turf Groomer on a non-
FlashAttach™ reel with a two bolt reel motor attachment,
reposition pivot block and clamp on driven assembly as
shown in Figure 7. Item numbers used in the following
instructions refer to the driven assembly Illustration on
Page 14.
a. Remove set screw from micro adjust knob (Item 19)
and remove knob.
b. Remove hardware (Items 24 & 10) holding pivot
block (Item 11) to driven side of groomer.
c. Remove bolt (Item 13) securing rod end (Item 12) to
cam (Item 23) and remove pivot block and adjuster
assembly.
d. Remove nut (Item 20) from adjusting bolt (Item 14)
and slide bolt from pivot pin (Item 21).
F
G
H
Z
AD
K
J
J
0.01
0.02
in.
AD
K
CAUTION
Pivot pin has a spring loaded detent. Be careful when
removing adjusting bolt.
A
L
M
A
B
N
Fairway Units
!
-
4
e. Slide pivot pin (Item 21) from pivot block (Item 11).
f. Reposition pivot block and loosely reassemble
hardware (Items 24 & 10). The screw mounts
through the inside flange of pivot block only.
g. Slide pivot pin (Item 21) through pivot block (Item
11). Remove plug (Item 17) from pivot pin. Compress
spring and ball (Items 15 & 16) and slide adjuster
assembly through pin.
h. Reassemble rod end to cam with bolt (Item 13) and
reassembly plug to pivot pin.
i. Replace nut (Item 20) on adjusting bolt (Item 14).
Tighten just enough to remove play and allow free
rotation of bolt.
j. Reassemble knob (Item 19) and set screw (Item 18).
Set screw must line up with indent in adjusting bolt.
k. Tighten pivot block mounting bolt (Item 24).
l. Remove bracket retaining clamp (Item 8) and
reassemble to its new position shown in Figure 7.
Figure 7
1.3 DRIVE/BLADE ASSEMBLY ________________________________________________________________________
1. Obtain drive assembly (B) and remove belt housing cover
(O) and belt (P). Set cover and belt aside.
2. Obtain blade assembly (C) and identify the drive end
(End with 16 tooth pulley). Slide the pulley through the
large slot in back of belt housing.
3. Align bearing housing with belt housing and secure with
one 3/8-16 x 7/8” socket head screw (Q) and lockwasher
(R). Do not tighten screw.
Figure 8
1.4 DRIVE ASSEMBLY TO REEL _______________________________________________________________________
1. Turn quick height adjuster knob (S) 90° to unlock the
height adjustment for ease of assembly.
2. Apply Lubriplate Multi-Lube (Part No. 5001581)
compound to the outside diameter of the bearing
housing.
3. Assemble cover plate (T) and drive/blade assembly to
counterweight end bearing housing. Align holes in cover
plate with holes in bearing housing and slots in belt
housing and secure with two 1/4-20 x 3/4” socket head
screws (U) and special washers (V).
Tighten the screws, then back off 1/8 to 1/4 turn. Belt
housing must be free to pivot.
4. Obtain roller assembly and remove nut (W) from both
ends. Thread nut (AJ) as far as possible onto shaft.
5. Slide one end of roller shaft into the “D” shaped hole of
drive assembly.
a. Center the blades between the roller grooves.
b. Loosely assembly one nut (W) to drive end of roller.
Do not tighten nut.
6. Assemble spacer block (X) with one 5/16-18 x 2-1/2”
carriage bolt, spacer, lockwasher and nut (Y)
. Do not
tighten hardware.
Figure 9
From This:
To This:
B
C
O
P
Q
R
Rotate 90°
Apply Lubriplate
D
S
T
U
V
W
AJ
X
Y
Y
Multi-Lube Compound
5
1.5 DRIVEN ASSEMBLY TO REEL______________________________________________________________________
1. Turn quick height adjusters knob (S) 90° to unlock the
height adjustment for ease of assembly.
2. Apply Lubriplate Multi-Lube compound to the outside
diameter of the bearing housing.
3. Align the blade assembly (C) and the roller assembly (D)
with their corresponding mounting locations on the driven
assembly (A). Slide driven assembly onto bearing
housing, blade assembly and roller.
a. Secure blade assembly with one 3/8-16 x 7/8” socket
head screw (Q) and lockwasher (R).
b. Loosely assemble nut (W) to driven end of roller. Do
not tighten.Thread nut (AJ) as far as possible onto
shaft.
4. Assemble spacer block (X) with one 5/16-18 x 2-1/2”
carriage bolt, spacer, lockwasher and nut (Y). Do not
tighten hardware. Be sure to install correct number of
shim washers (N) (Determined in Section 1.2).
Figure 10
1.6 CLUTCH ASSEMBLY _____________________________________________________________________________
1. Loosen eccentric retaining screw (AA) and turn eccentric
nut (AB) to move blade assembly pulley (AC) towards
reel shaft as much as possible.
2. 22” Groomer: Obtain drive pulley (J) from bag of parts
and place belt (P) on the pulley.
2. 18” Groomer: Obtain spacer (AD) from bag of parts and
slide onto reel shaft. Place belt (P) on pulley assembly (I).
NOTE:
To prevent permanent damage to the belt, do not
overtighten, twist, fold or bend the belt.
3. 22” Groomer: Position drive pulley (J) with bearing
towards center of reel and slide the pulley onto the reel shaft.
As you slide the pulley down the shaft, work belt over blade
assembly pulley (AC).
3. 18” Groomer: Install key (AE) onto reel shaft. Align
pulley assembly (I) with key and slide onto the reel shaft.
As you slide the pulley down the shaft, work belt over
blade assembly pulley (AC).
4. 22” Groomer: Install spacer (AD) and key (AE) onto reel
shaft.
5. 22” Groomer: Hold clutch (E) together and remove
shipping nut (AF).
NOTE:
The clutch assembly (E) is spring loaded and must be
held together before you remove shipping nut (AF) to
prevent the clutch from coming apart.
6. 22” Groomer: Align clutch (E) with key (AE) on reel shaft
and install clutch on the shaft. Secure by tightening bolt
(AG). Block the reel with a piece of wood and torque bolt
(AG) to 20 ft lb (27 Nm).
7. 18” Groomer: Secure pulley assembly to reel shaft with
3/8” hardware (H). Block the reel with a piece of wood
and torque bolt to 20 ft lb (27 Nm).
Figure 11
Figure 12
Rotate 90°
S
Q
R
W
AJ
X
Y
Y
N
C
D
A
AA
AB
AC
J / I
P
Q
AC
J
P
AD
AE
AF
AG
E
AE
AD
H
I
6
1.7 ADJUSTING BELT _______________________________________________________________________________
1. Place a deep well socket on eccentric nut (AB) and turn
to tighten belt. [See Figure 11]
NOTE:
Use a deep well socket without the ratchet. The belt must
be adjusted with hand pressure only.
2. Hold socket securely and torque screw (Q) to 20 ft lb (27
Nm).
3. Remove socket and torque retaining screw (AA) to 8 - 10
ft lb (11 - 13 Nm).
4. Assemble belt housing cover (O) and torque hardware
(AH) to 6 - 8 ft lb (8 - 11 Nm).
Figure 13
1.8 BLADE ASSEMBLY DRIVEN BEARING ADJUSTMENT__________________________________________________
1. Before the adjustment can be performed, set both quick
height adjusters (S) to the same detent position.
2. Restrain the blade assembly from turning, and loosen nut
(AK) one full turn towards nut (AL).
3. Remove 3/8-16 x 1” screw (AM), lockwasher (AN) and
flat washer (AO) from driven end of blade assembly.
4. Tighten hardware (Y) on both ends of reel.
a. After tightening hardware (Y), make certain driven
assembly (A) is shouldered squarely on the bearing
housing.
b. Add or remove shims as necessary until driven
assembly is shouldered squarely on the bearing
housing.
NOTE:
The squareness of driven assembly to the bearing
housing will affect how difficult or easy the turf groomer
is to adjust.
5. Assemble screw (AM) and flat washer (AO) to end of
blade assembly. Hand tighten only.
6. Tighten nut (AK) against spacer (AP) until spacer (AQ)
begins to rotate.
NOTE:
Nut (AK) is a nylock nut and is designed to resist turning.
7. Remove screw (AM) and flat washer (AO), and re-
assemble using lockwasher (AN). Torque screw (AM) to
20 ft lb (27 Nm).
8. Check to see if driven assembly (A) remains shouldered
against the bearing housing.
Figure 14
Figure 15
O
AH
CAUTION
Be careful to prevent entrapment of hands and fingers
between moving and fixed components of the
machine.
!
S
Q
R
W
AJ
X
Y
Y
N
C
D
A
AK
AL
AM
AN
AO
AP
AQ
7
1.9 FINAL ASSEMBLY _______________________________________________________________________________
1. Set height of cut to same height at both ends of reel.
2. Adjust nuts (AJ) as required to center blades between
roller grooves. Tighten nuts (N).
If any threads remain exposed after tightening nuts (N),
add spacers (AR) as required to cover threads.
3. Assemble guide wheels (AS) to roller shaft with 5/16-18 x
3/4” screws, spacers and lockwashers (AT). Wheels (AS)
must turn freely after assembly.
4. Tighten all remaining hardware securely.
5. Assemble lift yoke to reel and secure with shoulder bolts
(AU).
6. Raise quick height adjuster (S) to top notch and install
reel on mower.
7. Follow all steps for each remaining Turf Groomer to be
installed.
Figure 16
2.1 ADJUSTING PROCEDURE _________________________________________________________________________
1. Adjustments and maintenance should always be per-
formed by an qualified technician. If proper adjustment
cannot be made, contact an authorized Jacobsen®
Dealer.
2. Do not wear jewelry or loose fitting clothing when
adjusting or repairing any equipment.
3. Inspect the equipment on a regular basis; establish a
maintenance schedule and keep detailed records.
a. Keep the mower clean and moving parts properly
adjusted and lubricated.
b. Replace worn or damaged parts before operating the
machine.
c. Keep shields in place and all hardware securely
fastened.
4. Wash the equipment after each use. Do not wash any
portion of the equipment while it is hot. Do not spray
water directly at bearing housings and seals. Do not use
high pressure spray or steam.
5. Repair damaged metal surfaces and use touch up paint.
6. Use the illustrations in the Parts Catalog as reference for
the disassembly and reassembly of components.
2.2 GENERAL RECOMMENDATIONS ___________________________________________________________________
1. Initially, expect an increased amount of grass removal
when using the Turf Groomer. Also expect an increased
amount of wear on the reel and bedknife; therefore,
sharpening will be required more frequently. With contin-
ued usage, however, the frequency of sharpening will
decline.
2. Do not use the Turf Groomer immediately following top
dressing as the blades will pick up the top dressing and
pass it through the reel. The groomer should be raised to
its highest position and disengaged with the clutch knob.
3. Use the Turf Groomer on a regular basis, however, if you
wish to skip a day, the Turf Groomer should be
disengaged. The groomer blades will simply roll on the
ground without leaving any marks.
4. The Turf Groomer may also be raised to its highest level
but leave clutch knob engaged so that the blades will
rotate though the grooves in the roller and keep the roller
grooves clean.
2.3 HEIGHT OF CUT _________________________________________________________________________________
Before this attachment can be put into regular use, several
passes should be made over a test area, each pass at a
different setting to obtain the best possible results for your turf
conditioning needs.
1. Record the settings and conditions during the first test.
Examine the test area a few days after the first grooming
AJ
N
AR
AS
AT
AU
S
WARNING
Before you clean, adjust, or repair this equipment,
disengage all drives, lower cutting units to the ground,
engage parking brake, stop engine, remove key from
switch and disconnect Negative (BLACK) battery cable to
prevent injuries.
CAUTION
Be careful to prevent entrapment of hands and fingers
between moving and fixed components of the
machine.
!
!
8
and record the results.
2. Your requirements will determine the final settings and
they will be governed by the type and condition of the
grass, temperature and season of the year, the frequency
of cut and many other variables.
3. Keep in mind that the conditions and settings will vary
from green to green and from one season to the next.
NOTE:
Over grooming can cause severe damage to turf.
2.4 REEL HEIGHT OF CUT ____________________________________________________________________________
1. To set the cutting height for the reel, loosen the wing nut
(D) and thread screw (A) in or out to obtain the desired
height of cut (B) on gauge bar (C).
Use a small metal scale to measure dimension (B) as the
height of cut. Once dimension (B) is obtained, tighten
wing nut (D).
2. Loosen nuts (E) on both ends of the reel just enough to
allow knob (F) to raise or lower the roller brackets.
3. Place gauge bar across the front and rear rollers at one
end of the reel.
4. Slide the head of screw (A) over the bedknife and adjust
knob (F) to close the gap between the screw head and
the bedknife.
5. Repeat adjustment on opposite end of reel.
6. Recheck both ends of reel for proper adjustment and
tighten nuts (E).
Figure 17
2.5 TURF GROOMER HEIGHT OF CUT ADJUSTMENT _____________________________________________________
1. The height of cut adjustment on the Turf Groomer is
made with the “Quick” and “Micro” adjusters and the
gauge bar (C).
a. The “Quick” height adjusters (J) allows changes in
increments of 1/8 in. (3 mm) per detent position.
b. The “Micro” height adjusters (K) permits infinite
variations between the 1/8 in. increments. Each
“click” of the micro adjuster moves the groomer shaft
0.007 in (0.18 mm) up or down.
2. The height of cut for the reel must be adjusted before the
Turf Groomer height of cut can be set. If reel height of cut
is changed, the groomer will need to be re-adjusted.
3. To set grooming height, loosen wing nut (G) and adjust
screw (H) from 0 to 1/16 in (2 mm) below reel height of
cut (B).
4. Place the gauge bar across the front and rear rollers on
one end of the reel with head of screw (A) over the
bedknife.
5. Unlock the “Quick” height adjuster (J) on one end of reel
by turning knob 90° and bring the groomer blades down
as close to screw (H) as the lowest detent allows. Lock
adjuster.
6. Move “Quick” height adjuster on opposite end of reel to
same detent position.
7. Finish adjustment using “Micro” adjusters (K) on both
ends of reel.
8. Do not set the blades at ground level or below. To
mow at this level may damage the machine as well as the
turf. The Turf Groomer was designed to be a conditioner,
not a vertical mower.
9. Jacobsen does not recommend setting the groomer
blades over 1/16 inch below the reel cutting height.
This height will also help eliminate natural graining and
smooth out uneven grass
10. Make absolutely certain that each Turf Groomer is
adjusted evenly on both ends and that all the cutting units
on the mower are adjusted to the same height.
Figure 18
A
B
C
D
E
F
A
B
C
G
H
J
K
0-1/16 in.
9
2.6 CLUTCH KNOB (22” GROOMER ONLY) ______________________________________________________________
Note: The 18” groomer is not equipped with a clutch knob
and is designed to be always ON.
1. The Turf Groomer is equipped with a clutch to disengage
the groomer blades and allow you to cut grass with the
reel only.
2. The groomer blades should be raised to their highest
position and the clutch knob disengaged when groomer is
not in use.
3. To disengage the clutch, hold pulley (L) and turn clutch
knob (M) 110° counter-clockwise. Make sure the groomer
is disengaged by manually turning pulley (L) and check if
groomer blades turn.
Figure 19
2.7 BELT __________________________________________________________________________________________
1. The drive belt used on the Turf Groomer is a patented
design, Kevlar® cord, syncronus belt.
NOTE:
To prevent permanent damage to the belt, do not
overtighten, twist, fold or bend the belt.
Overtightening the belt will cause premature belt failure and
abraisive wear of the pulley and bearings. Twisting or bending
the belt will permanently damage the cord fibers of the belt.
2. Once the belt has been adjusted as described in the
assembly process, no further adjustment is required.
[See Section 1.7]
3. Periodic inspections of the belt will be required to check
for wear.
4. Spare belts should be stored individually and not
compressed or bent into any form other than eliptical.
2.8 LUBRICATION ___________________________________________________________________________________
Lubrication intervals are based on operating from 8 to 10
hours per day, 5 days per week under normal operating
conditions.
All maintenance intervals must be performed more frequently
when operating in extremely dusty conditions.
1. Always clean the grease fitting before and after lubricat-
ing.
2. Lubricate with grease that meets or exceeds NLGI Grade
2 specifications.
3. Apply grease with a manual grease gun and fill slowly
until pressure is felt. Do not use compressed air guns to
prevent damage to seals.
Grease each of the following points not more than once a
month.
a. Clutch (22” Groomer Only) (1 Fitting) (N)
b. Groomer bearing housings (2 Fittings) (O)
c. Roller bearings (2 Fittings) (P)
d. Micro Adjust Pivot (2 Fittings - See Note) (Q)
NOTE:
To grease motor side micro-adjust pivot, remove grease
fitting (Q) from micro-adjust pivot on opposite end of reel
and plug (R). Install fitting and grease motor side pivot.
Reinstall all parts to their original position. This is
applicable to all units except for G-Plex.
4. For smooth operation of pivot points and other friction
points, apply several drops of SAE 30 wt. oil every 40
hours, or as required.
Clean and lubricate individual parts and components as
required. Apply Lubriplate Multi-Lube compound between
bearing housings and drive / driven assemblies.
Figure 20
WARNING
Never hold onto the reel blades during the engaging
or disengaging operation. If it is necessary to stop the
rotation of the reel, place a wood block between a reel
blade and the frame.
!
L
M
N
O
P
P
Q
R
10
A
A
A
2
3
3
5
6
6
7
7
8
9
10
12
12
11
13
13
14
16
19
20
21
22
23
24
27
28
29
30
31
33
4
17
15
25
26
34
38
37
18" Groomer
22" Groomer
35
36
36
32
1
TURF GROOMER
Turf Groomer Assembly
Right Hand Groomer Shown (Left Opposite)
Serial No. All
11
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
1
365226 1 Cover Plate
> 2500229 1 Pulley Assembly 22” Groomers Only
2 365228 1 • Pulley, 28 Groove 22” Groomers Only
3 365229 2 • Bearing, Ball 22” Groomers Only
4 458461 1 • Snap Ring 22” Groomers Only
5 365232 1 • Spacer 22” Groomers Only
6 365256 1 Spacer, Pulley
7 365239 1 Key, 1/8 x 1/8 x 7/16”
8 446142 2 Lockwasher, 3/8 Heavy
9 434030 2 Screw, 3/8-16 x 7/8” Socket Head
10 365237 2 Spacer, Grass Catcher
11 441672 2 Carriage Bolt, 5/16-18 x 2-1/2”
12 364441 4 Spacer, 5/16
13 446136 4 Lockwasher, 5/16 Heavy
14 443106 2 Nut, 5/16-18 Hex
15 365246 2 Bolt, 3/8-16 Nyloc Shoulder
16 365341 2 Washer, Special
17 434031 2 Screw, 1/4-20 x 3/4” Socket Head
>18
19 365343 2 Wheel, Guide
20 400184 2 Screw, 5/16-18 x 3/4” Hex Head
21 365409 AR Spacer, Roller
22 3005515 AR Spacer, Driven Assembly 0.02”
– 1 Clutch Assembly 22” Groomers Only
23 163776 1 • Pulley Assembly 22” Groomers Only
24 338768 1 • • Seal, Grease 22” Groomers Only
25 365272 2 • Spring 22” Groomers Only
26 365258 2 • Pin 22” Groomers Only
27 365254 1 • Shaft, Stub 22” Groomers Only
28 241817 1 • Knob, Clutch 22” Groomers Only
29 363841 1 • Washer 22” Groomers Only
30 446142 1 • Lockwasher, 3/8 Heavy 22” Groomers Only
31 365257 1 • Bolt 22” Groomers Only
32 471214 1 • Grease Fitting, 1/4-28 22” Groomers Only
33 – 1 Drive Assembly See Breakdown
34 – 1 Driven Assembly See Breakdown
35 – 1 Blade Assembly See Breakdown
36 – 1 Roller Assembly See Breakdown
37 365235 1 Belt, Drive
38 4118617 1 Pulley Assembly 18” Groomers Only
365228 1 • Pulley, 28 Groove Groomer 18” Groomers Only
4118618 1 • Pulley, Rear Roller Brush 18” Groomers Only
12
TURF GROOMER
Drive Assembly
Right Hand Groomer Shown (Left Opposite)
Serial No. All
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
9
30
29
31
26
13
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
>
1
4103100 1 Bracket, Groomer Roller
2 220302 1 Housing, Belt
3 365260 1 Link, Belt Adjusting
4 367162 1 Eccentric, Belt Adjusting
5 446142 1 Lockwasher, 3/8 Heavy
6 434030 1 Screw, 3/8-16 x 7/8” Socket Head
7 2500231 1 Cover, Belt Housing
8 338752 1 • Seal, Oil
9 446130 3 Lockwasher, 1/4 Heavy
10 434029 2 Screw, 1/4-20 x 1” Socket Head
11 434011 1 Screw, 1/4-20 x 5/8” Socket Head
12 365247 1 Rod End
13 446136 1 Lockwasher, 5/16 Heavy
14 434032 1 Screw, 5/16-18 x 1-3/4” Socket Head
15 365270 1 Bolt, Micro Adjusting
16 3003969 1 Pin, Pivot
17 465006 1 Ball, 5/16 Diameter Steel
18 365291 1 Spring
19 471219 1 Grease Fitting, 1/8 NPT
20 445667 1 Nut, 1/2-20 Hex Nyloc
21 422502 1 Set Screw, 1/4-20 x 1/4”
22 3005108 1 Knob, Micro Adjuster
23 367166 1 Cam
24 453009 1 Flat Washer, 5/16
25 434024 1 Screw, 5/16-18 x 3/4” Socket Head
26 400186 2 Screw, 5/16-18 x 7/8” Hex Head
27 364061 1 Bracket, Adjusting Pivot
28 365344 1 Clamp, Housing Retaining
29 444718 2 Nut, 5/16-18 x 7/8” Hex Head
30 365233 1 Link, Roller Adjusting
31 – 1 Quick Height Adjuster See Breakdown
14
TURF GROOMER
Driven Assembly
Right Hand Groomer Shown (Left Opposite)
Serial No. All
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
3
24
25
15
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
>
1
4103100 1 Bracket, Groomer Roller
2 338748 1 Bracket, Groomer Mounting
3 400186 2 Screw, 5/16-18 x 7/8” Hex Head
4 365233 1 Link, Roller Adjusting
5 444718 2 Locknut, 5/16-18 Center
6 453009 2 Flat Washer, 5/16
7 364061 1 Bracket, Adjusting Pivot
8 365342 1 Clamp, Backet Retaining
9 446136 1 Lockwasher, 5/16 Heavy
10 2811566 1 Screw, 1/4-20 x 1/2” Locking
11 2810479 1 Block, Pivot
12 365247 1 Rod End
13 434032 1 Bolt, 5/16-18 x 1-3/4” Socket Head
14 365270 1 Bolt, Micro Adjusting
15 465006 1 Ball, 5/16 Diameter Steel
16 365291 1 Spring
17 472006 1 Pipe Plug, 1/8 NPT Socket Head
18 422502 1 Set Screw, 1/4-20 x 1/4”
19 3005108 1 Knob, Micro Adjuster
20 445667 1 Nut, 1/2-20 Hex Nyloc
21 3010709 1 Pin, Pivot
22 434024 1 Screw, 5/16-18 x 3/4” Socket Head
23 367166 1 Cam
24 1 Quick Height Adjuster See Breakdown
25 323016 1 Grease Fitting, 1/8 PTF, 90° 67912 and 67914 Models Only
16
TURF GROOMER
Blade Assembly
1/4 Inch Spacing, Right Hand Groomer Shown (Left Opposite)
Serial No. All
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
2
3
6
9
10
11
14
20
21
24
26
17
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
1
367029 1 Locknut, 3/4-16 Hex Nyloc
2 367165 2 Spacer, 7/8 x 17/32”
> 3 471221 2 Grease Fitting, 1/4-28
2500228 1 Driven Bearing Housing
4 241808 1 • Housing, Bearing
5 365229 1 • Bearing, Ball
6 458461 2 • Snap Ring
7 336962 1 • Grease Seal
8 367164 1 Spacer, 7/8 x 1-13/16”
9 453011 2 Flat Washer, 3/8
10 446142 2 Lockwasher, 3/8 Heavy
11 400298 2 Screw, 3/8-24 x 1” Hex Head
2500227 1 Drive Bearing Housing
12 241807 1 • Housing, Bearing
13 365229 1 • Bearing, Ball
14 458461 2 • Snap Ring
15 336962 1 • Grease Seal
16 367163 1 Spacer, 7/8 x 7/8”
17 365227 1 Pulley, 16 Groove
18 345556 1 Key, 1/8 x 1/8 x 31/32”
2500232 1 1/4” Spacing Groomer Shaft Assy 67911 and 67912
2500230 1 1/2” Spacing Groomer Shaft Assy 67913 and 67914 (Not Shown)
4116926 1 1/2” Spacing Groomer Shaft Assy 67926 (Not Shown)
19 390857 1 • Shaft, 22” Groomer 67911, 67912, 67913 and 67914
19 3000782 1 • Shaft, 18” Groomer 67926
20 365234 2 • Spacer, 1-1/16 x 15/32”
● 21 365230 71 • Blade (1/4” Spacing) 67911and 67912
● 21 365230 40 • Blade (1/2” Spacing) 67913 and 67914
● 21 365230 32 • Blade (1/2” Spacing) 67926
22 367029 1 • Locknut, 3/4-16 Hex Nyloc
23 364040 AR • Shim, Groomer Shaft
24 367161 2 • Spacer, 1 x 3/4”
25 443832 1 • Nut, 3/4-16 Hex Jam
26 365236 70 • Spacer, 1/4” Blade Spacing 67911 and 67912
26 365234 39 • Spacer, 1/2” Blade Spacing 67913 and 67914
26 365234 31 • Spacer, 1/2” Blade Spacing 67926
● Part Number 365230 is a package of 50 blades
18
> Change from previous revision
TURF GROOMER
Roller Assembly
Serial No. All
Item Part No. Qty. Description Serial Numbers/Notes
1
390899 1 22” Roller Tube, 1/4” Spacing 67911 and 67912
1 390900 1 22” Roller Tube, 1/2” Spacing 67913 and 67914
1 4116739 1 18” Roller Tube, 1/2” Spacing 67926
2 365330 2 Bearing, Ball
3 4169260 2 Shaft, Roller
4 338773 2 Grease Seal
5 458113 2 Snap Ring
6 446148 2 Lockwasher, 7/16 Heavy
7 443816 2 Nut, 7/16-20 Hex Jam
8 452008 2 Flat Washer, 7/16
9 443836 4 Nut, 7/8-14 Hex Jam
10 365345 2 Nylos Ring
11 471214 2 Grease Fitting, 1/4-28
1
2
3
4
5
6
7
8
9
10
11
19
> Change from previous revision
TURF GROOMER
Item Part No. Qty. Description Serial Numbers/Notes
1
422502 1 Set Screw, 1/4-20 x 1/4”
2 365265 1 Link, Adjusting
163761 1 Knob Assembly
3 365271 1 • Bolt
4 365268 1 • Spring
5 365267 1 • Plunger
6 365266 1 • Bolt, Adjusting
7 365269 1 • Spring
8 444708 1 • Locknut, 1/4-20 Hex Center
9 271919 1 Knob, Quick Adjuster
Quick Height Adjuster
Serial No.
1
2
3
4
5
6
7
8
9
Jacobsen, A Textron Company
11108 Quality Drive, Charlotte, NC 28273
www.Jacobsen.com
800-848-1636
Equipment from Jacobsen is built to exacting
standards ensured by ISO 9001 and ISO 14001
registration at all of our manufacturing locations.
A worldwide dealer network and factory trained
technicians backed by Jacobsen Parts Xpress
provide reliable, high-quality product support.
When Performance Matters.
™
/