Contec CPSL-08P1EN Owner's manual
- Category
- Network switches
- Type
- Owner's manual
Product Guid
e
CONTEC CO.
,
LTD.
3-9-31
,
Himesato
,
Nishi
y
odo
g
awa-ku
,
Osaka 555-0025
,
Ja
p
an
https://www.contec.com
/
No part of this document may be copied or reproduced in any form by any means
without prior written consent of CONTEC CO., LTD.
NA06719 (LYXA012) 06032019_rev2 [05312019] June 2019 Edition
IO-Link Master Module (8-channel)
CPSL-08P1EN
Thank you for purchasing this product. The product you have purchased consists of the
following items.
Check, with the following list, that your package is complete.
If you find any item either missing or damaged, please contact the sales representative you
purchased the product from.
Before actual use, read the Reference Manual which can be viewed on the CONTEC website
to use this product properly.
The following guide and manual come with this product. Visit the CONTEC website and
download the manual before using the product.
The name of the documents Contents How to
g
et
Product Guide (This sheet) This lists the product configuration
and describes the
p
recautions.
Included in the package
(Printed matter)
Reference Manual This describes the hardware aspects
such as functions and settin
g
s.
Download(PDF)
Download
https://www.contec.com/download/
1. About the Product
This product is an IO-Link master module with 8 channels of IO-Link ports (Class A). It sup-
ports industrial Ethernet protocols of differing makers, and can connect to the network of
PROFINET, EtherNet/IP, MODBUS/TCP, and CC-Link IE Field Basic with the switches on the
product.
8 channels of IO-Link ports can set parameters independently, and the settings of IO-Link
mode and SIO mode can be configured per port.
As this product has a web server function, the user can install the functions through a Web
browser without using a specific tool.
2. Product Configuration
Check, with the following list, that your package is complete.
Product...1 Product Guide
(This docu-
ment)...1
Warranty
Certificate...1
Serial Number La-
bel...1
Waterproof cap...1
3. Safety Precautions
Understand the following definitions and precautions to use the product safely.
Safety Information
DANGER
Do not use the product in locations exposed to a flammable or corrosive gas. It may
cause explosion, fire, electrical shock, or malfunction.
Do not allow the device to come into contact with foreign substances (metal particles,
flammable substances, liquids, etc.) from the connector terminal or through the opening.
Otherwise, it can cause fire or electrical shock.
Do not place the product in an unstable location or use incomplete mountings. Other-
wise, it may cause the device to fall.
Be sure to connect the product to the stipulated power supply voltage. Connecting to a
different voltage might cause a fire or electrical shock.
If the product is used in a manner not specified by the manufacturer, the protection pro-
vided by the equipment may be impaired.
The product is not intended for use in aerospace, space, nuclear power, medical equip-
ment, or other applications that require a very high level of reliability. Do not use the
product in such applications.
If using the product in applications where safety is critical such as in railways, automotive,
or disaster prevention or security systems, please contact your retailer.
CAUTION
Be certain the following requirements are satisfied when using the product.
- Indoor use
- Altitude up to 5000m
- Applicable POLLUTION DEGREE 2
When using the product at high altitudes, refer to the relational expression below to find
an appropriate ambient temperature. The heat dissipation decreases due to air pressure
drop and could lead to damages or a shorter product life.
- Ambient temperature = 60[°C] - 0.005 x altitude [m]
An Example)
The product is used at 2000 meters
60°C - (0.005 x 2000m) = 50°C (Ambient temperature)
Do not use or store the product in a location exposed to extremely high or low temper-
ature that exceeds range of specification or susceptible to rapid temperature changes.
e.g. - Exposure to direct sun
- In the vicinity of a heat source
Do not use the product in extremely humid or dusty locations. It is extremely dangerous
to use the product with its interior penetrated by water or any other fluid or conductive
dust. If the product must be used in such an environment, attach the waterproof cap or
install it on a dust-proof control panel, for example.
Avoid using or storing the product in locations subject to shock or vibration that exceeds
range of specification.
When transporting the product, take suitable measures to avoid applying shock or vibra-
tion directly to the product.
Impact resistance: 15G (11ms) below.
Use the product in the specified operating condition (temperature, humidity, vibration
and shock).
Do not use the product in the vicinity of devices that generate strong magnetic force or
noise. Such products will cause the product to malfunction (stop, reboot).
Do not use or store the product in the presence of chemicals.
When removing connectors or cables, always unplug the power cables and confirm the
LEDs are turned off.
Do not modify the product. CONTEC will bear no responsibility for any problems, etc.,
resulting from modifying the product.
In the event of failure or abnormality (foul smells or excessive heat generation), unplug
the power cables immediately and contact your retailer.
To connect with peripherals, use a grounded, shielded cable.
To clean the product, wipe it gently with a soft cloth dampened with either water or mild
detergent. Do not use chemicals or a volatile solvent, such as benzene or thinner, to
prevent the paint to be scraped or discolored.
When connecting cables, first check the shapes of connectors, and then insert them in
the correct orientation. After they are connected, do not put too much load on the con-
nected part. Doing so may result in poor contact or damage to the product and the
connected part.
Do not touch metal parts or terminals with your hands when the product is in operation.
Otherwise, the product may malfunction, or cause failure.
Do not touch the product or connectors with a wet hand to avoid electric shock.
The specifications of the product are subject to change without notice for enhancement
and quality improvement. Even when using the product continuously, be sure to read the
manual in the CONTEC’s website and understand the contents.
When the product is used in a place that is affected by overcurrent or overvoltage (light-
ning surge), select appropriate surge protection device for all of the route (Power line,
LAN, IO-Link, earth, etc.). Consult with the specialist regarding selecting, purchasing,
and setting the surge protection device.
When disposing of the product, follow the disposal procedures stipulated under the rel-
evant laws and municipal ordinances.
In ambient temperature above 45°C, never touch the product (Housing, FG panel, and
connector) with your hand as they may cause a burn during the operation since they
become extremely hot.
Regardless of the foregoing statements, CONTEC is not liable for any damages whatso-
ever (Including damages for loss of business profits) arising out of the use or inability to
use this CONTEC product or the information contained herein.
4. Optional Products
DIN rail fitting power supply (Input: 100 - 240VAC)
30W(Output: 24VDC 1.3 A): CPS-PWD-30AW24-01,
90W(Output: 24VDC 3.8 A): CPS-PWD-90AW24-01
5. Product Nomenclature and
Function
Nomenclature of Product Components
Number Name Number Name
1 LAN port 7 Address settin
g
switch
2 FE terminal 8 Protocol settin
g
switch
3 Status LED 9 IO-Link connecto
r
4 Mode settin
g
switch 10 Screw mountin
g
hole
5 Maintenance connector 11 Power input connecto
r
6 Selection switch for address
settin
g
s
12 Power output connecto
r
LAN Port
Pin
number
Signal
number
Description
1 TX+
Transmission data (+)
Output
2 RX+
Reception data (+) In-
put
3 TX-
Transmission data (-)
Output
4 RX-
Reception data (-) In-
put
LED name LED color Description
ACT Orange
ON : It indicates that transmitting and receiving data with the
connected external device.
OFF : It indicates that LAN port is not connected or there is no
data transmission/reception.
LINK Green
ON : It indicates that LAN port is in a connecting state with the
connected external device.
OFF : It indicates that cable is not connected or linking with the
connected external device has not established
y
et.
Status LED
LED name LED color Description
ST Red
ON : It lights up when the error occurs.
OFF : It indicates the s
y
stem runs normall
y
.
BF/NS/ERR Green/Red Refer to the “Reference Manual”.
SF/MS/RUN Green/Red Refer to the “Reference Manual”.
SYS
Green
ON : It lights up when the system runs normally.
FLASHING : It indicates that reading the firmware.
(SYS Flashing alternately with yellow LED)
OFF : It indicates that the power has not been supplied or CPU is
not runnin
g
.
Yellow
ON : It lights up when the error occurs.
FLASHING : It indicates that reading the firmware.
(SYS Flashing alternately with green LED)
OFF : It indicates the s
y
stem runs normall
y
.
Protocol Setting Switch
Set communication protocol of LAN port.
Setting value Setting contents
0
PROFINET
1 EtherNet/IP
2 MODBUS/TCP
3 CC-Link IE Field Basic
4 - F Do not set anything.
Selection Switch for Address Settings
Select a setting measure for the IP address of the product.
Setting value Setting contents
0
DHCP
1 BOOTP (EtherNet/IP only)
2 Set with the address setting switch.
3 - F Do not set anything.
Address Setting Switch
There are two switches for setting addresses and the addresses are set in hex.
“H” and “L” represent high bits and low bits respectively.
The setting range is 00 - FEh (0 - 254).
Setting value Setting contents
00h Refer to the “Reference Manual”.
01 - FEh It is a setting range for addresses.
[H] [L] Settin
g
value 00h (Factor
y
settin
g
s)
IO-Link Connector
Pin
number
Signal
name
Description
1 L+
Power supply to the connected
device (+)
2 DI Digital input
3 L-
Power supply to the connected
device (-)
4 C/Q
IO-Link communication/Digital
I/O
5 N.C. This is left unconnected
LED name LED color Description
ACT Orange
ON : The state is ON in the SIO mode.
OFF : The state is OFF in the SIO mode or indicates IO-Link mode.
ST
Green
ON : It is connected with the connected external device in the
IO-Link mode.
Flashing : It is not connected in the IO-Link mode.
OFF : Either SIO mode or the port is disabled.
Red
ON : It lights up when an error occurs in the IO-Link mode.
OFF : Either SIO mode or the port is disabled.
LINK Orange
ON : DI terminal (Pin2) input is in ON state.
OFF : DI terminal (Pin2) input is in OFF state or the port is disabled.
Power Input Connector
Pin
number
Signal
name
Description
1 U
S
Sensor/System power
2 GND_U
A
Ground of the auxiliary power
3 GND_U
S
Ground of sensor/system power
4 U
A
Auxiliary power
(Unavailable with this product)
FE FE Functional earth
LED name LED color Description
U
S
Green
ON : U
S
power has been supplied.
OFF : U
S
power has not been supplied.
U
A
Green
ON : U
A
power has been supplied.
OFF : U
A
power has not been supplied.
Power Output Connector
Pin
number
Signal
name
Description
1 U
S
Module/Sensor power
2 GND_U
A
Ground of the auxiliary power
3 GND_U
S
Ground of module/sensor power
4 U
A
Auxiliary power
FE FE
It is a terminal for functional earth.
Connect this to earth
g
round.
6. Physical Dimensions
-
1
Contec CPSL-08P1EN Owner's manual
- Category
- Network switches
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec CPSL-08P1EN Owner's manual
-
-
-
-
-
-
-
-
-