Zelmer ZFA1010S User manual

Page is loading ...

26 GW24-007_v01

Dear Clients!

Please read these instructions carefully. Pay your special attention to important safety instructions.

Keep this User’s Guide for future reference.

The manufacturer/importer does not accept any liability for any damages resulting from un-

intended use or improper handling.

The manufacturer/importer reserves his rights to modify the product any time in order to ad-

just it to law regulations, norms, directives, or due to construction, trade, aesthetic or other

reasons, without notifying in advance.

IMPORTANT SAFETY INSTRUCTIONS

Please connect the fan to 220–240 V mains supply. –

Do not unplug by pulling by cord. –

Do not use the appliance, when the casing, protecting grill or the cord is visibly damaged. –

If the non-detachable part of the cord is damaged, it should be replaced by the producer or at

a proper service point or by a qualied person in order to avoid any hazards.

The appliance can be repaired by qualied staff only. Incorrectly performed repair may cause

serious hazard to the user. In case of any defects, it is advised to return the appliance to an

authorised service facility.

Disconnect fan from mains supply outlet when moving from one location to another. –

Never insert ngers, pencils, or any other object through the grille when fan is running. –

Disconnect fan from mains supply outlet before cleaning. –

Disconnect fan from mains supply outlet when removing grilles. –

Make sure that you disconnected fan from mains supply outlet (remove the plug from the socket) –

when removing housing (protecting grilles).

Make sure fan is on a stable surface when operating to avoid overturning. –

Do not use fan in window. Rain may create electrical shock hazard. –

This appliance is not intended for use by persons (including children) with reduced physical, –

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for their

safety.

Children should be supervised to ensure that they do not play with the appliance. –

TECHNICAL DATA AND BINDING STANDARDS

The fan is II class appliance and it meet the requirements of binding standards.

The appliance meets the requirements of the following directives:

Low Voltage Device (LVD) – 2006/95/EC. –

Electro- Magnetic Compatibility (EMC) – 2004/108/EC. –

The product is marked with CE symbol on the name plate.

Voltage: 220–240 V/50 Hz. ●

Power: 40 W. ●

Propeller diameter – 30 cm. ●

3 air ow speeds. ●

Horizontal oscillation. ●

Oscillation blockade. ●

Fan leaning angle setting (upwards, downwards). ●

Fan technical data are presented on the name plate.

EN

27GW24-007_v01

FAN OUTLINE

1. Front protecting grill.

2. Spinner.

3. Propeller.

4. Plastic nut.

5. Back protecting grill.

6. Retaining pin.

7. Stand.

8. Circlip of grills.

9. Protecting grill fastener.

10. Base.

11. Fastening screw.

12. Head oscillation button.

13. Fan leaning adjustment knob.

14. Supplying cord.

15. ON/OFF and rotation buttons.

The product you purchased is partially disassembled.

Assemble thoroughly before usage according to the following description.

PROPELLER AND PROTECTING GRILLS ASSEMBLING

Move the grill fasteners ( – 8) outside.

Remove front protecting grill from the circlip ( – 9).

Unscrew the spinner ( – 2) clockwise.

Remove the propeller ( – 3) from the fan shaft.

Unscrew plastic nut ( – 4) counter-clockwise.

Set the back protecting grill ( – 5) in right position – handle upright.

Tighten plastic nut ( – 4) exactly to back grill hub.

Assemble the propeller ( – 3) at the shaft, so that retaining pin (6) got into the recess at the fan

hub.

Turn the spinner ( – 2) to the fan shaft counter-clockwise.

Insert the bottom edge of front grill ( – 1) into the circlip (9), press it towards back grill (5) and press

protecting grill fasteners (8) inside.

BASE ASSEMBLING

1. Snap the pedestal post (7) into the base (10) by pushing down it until it

locks in the base.

2. Insert the screw (11) into the hole in the base (10).

3. Tighten the screw as much as possible.

Check if all elements have been assembled properly!

28 GW24-007_v01

HANDLING

1. Select the airow direction upwards or a bit down-

wards (B) untighten the leaning adjustment knob

(13) and set the best angle of head leaning – air-

ow. Tighten the knob (13).

2. Insert supplying cord (15) into mains supply outlet.

3. Switch on selected ro-

tation speed pressing

rotation button (14): 1,

2 or 3. You can change

rotation speed during

fan operation.

4. To switch on/off fan head oscillate (A), press in/pull

out the button (12).

5. Press the on/off „0” button to switch off the fan.

CLEANING

Make sure to unplug from the electrical supply source before cleaning. –

Plastic parts should be cleaned with mild soap and a damp cloth or sponge. Thoroughly to re- –

move soap lm with clean water.

Dry thoroughly; make sure that water or other liquid did not get inside of motor. –

ECOLOGY – ENVIRONMENT PROTECTION

Each user can protect the natural environment. It is neither difcult nor expensive.

In order to do it: put the cardboard packing into recycling paper container; put the

polyethylene (PE) bags into container for plastic.

When worn out, dispose the appliance to particular disposal centre, because of the

dangerous elements of this appliance, which can be hazardous for natural environ-

ment.

Do not dispose into the domestic waste disposal!!!

Zelmer ZFA1010S User manual

This manual is also suitable for

Zelmer ZFA1010S User manual

in other languages

Related papers

Other documents