KitchenAid 9743822 User manual

Brand: KitchenAid

Model: 9743822

Category: Dishwashers

Type: User manual

This manual is also suitable for

I itChenAid ®

HOME APPLIANCES

APPAREILSI_LECTROM_:NAGERS

www.kitchenaid.com

_---------._

Quick Reference

Section

Introduction

Page

Product dlmenslons 3

Bullt-ln opening dlmenslons 3

Electrical requlremonts 4

Water requlrements 4

Draln requlrements 4

Installation steps 5 -

Need assistance? Back cover

The KitchenAidConsumerAssistance Centeris open24 hoursa

day,7 daysa week. Call1-(800) 422-1230.Thecallis free withinthe

continentalUnitedStates.In Canada,call 1-(800) 461-5681for

English,and 1-(800) 461-5703for French.

Call t_ KitchenAtdConsumerAssistance Centerwhen you:

Havequestionsaboutdishwasherinstallationoroperation.

1_ Needtoobtainthenameand numberofa KitchenAid-authorized

servicecompany,

Important:

• Installer:. LeaveInstalLationInstructionswiththe homeowner.

• Homeowner: KeepInstallationInstructionsforfuture

reference.

• SaveInstallationInstructionsforlocalelectricalinspector's use,

PartNo. 9743822 Rev,C

Piece n° 9743822 R_. C

In_on s_s cont fmm _ s

If connecting dishwasher with power supply cord,

check that power supply is dlsconne_ed.

ElectricalShockHazard

PlugIntoa grounded3 prongoutlet.

Donotremovegroundprong.

Do notuseanadapter.

Donotuseanextansloncord.

FailuretofollowtheseInstructionscanresultIn death,fire,

orelectricalshock.

• Usepowersupply cord kit (Part No. 4317824) availablefromyour

dealer orpartssupplier.Followinstructionswithkitforinstalling

powersupplycord.

Ifthe cord kitis notacailable,a U.L.-listed/CSA-cerlifled,16-gauge,

three-conductor,power supplycord and m.ainreliefmustbe

used.Sixfeet(1.8m) mustbethe maximumlengthof power

supplycord.

• Routepowersupplycord so itdoesnot touchdishwashermotoror

lowerpartofdishwasherrob.

_ *Removethedishwasherterminalboxcover(O).

• Installa U.L.÷listed/CSA-certiliedstrain relief(P) totheterminal

box. Runpower supplycord throughstrain relief.

A. electric drill

B. Phillips screwdriver

C. flat-blade screwdriver

D. 2 adjustable wrenches

E. pliers

F. measuring tape or ruler

G. pipe wrench

H. hole cutters (1/2", 3/4",

t-ln")

1. tubing cutter

J. wire stripper

K. utility knife

L. 11/32" and 1/4" nut driver

or hex socket

M. 2 twist-on wire connectors

for 16-gange wire

N. level

O. safety glasses

P. gloves

R. Teflon tape

S. Drain tube adapter

Part No. 9741366

(available from your

dealer) if connecting to a

1/2" I.D. drain line.

Not shown:

90 ° elbow with 3/8" N.P.T.

external threads on one

end. The size of the other

end must fit your water

supply line.

A. 2 drain hose clamps

B. 2 No.-lO x 1/2" Phillips-head screws

Remove parts from bag. Check thatall parts were supplied.

(6xem)

34"(S6._)

Unshaded area must be free ofpipes, wiresanddrain hose.

Power supply cord or cable shouldnot bekinkedorpinchedbetwom

dishwasherandcab'met.

Leveling legs and wheels adjusttofit34-inch (86.4cm) to35-inch

(88.9cm) cabinetopeningheight.Iflevelinglegsand wheelsare removed

fromdishwasher,33-13/16inches (85.9cm) istheminimumcabinetopening

height.Measurethisdistancefromthe lowestpointofthe underside ofthe

countertop.

Cornerlocations requirea 2"(5.1cm) minimumclearancebetweenside of

dishwasherdoor and the wallor cabineL

Checklocation where dishwasherwillbeinstalled.Do Notinstalldishwasher

over carpeting.Thelocationmustprovide:

• Protection so thatthe water inlet and drain lines cannot freeze.

Damagefromfreezingis notcoveredbythe warranty.Ifdishwasher will

be subject to freezing temperatures and leftunused foraperiodof

time, see"Winterizing"instructionsinyourUseand CareGuide.

• Easyaccess to water,dectvidtyand drainagelines.

• Convenientloading.Thebestlocationis tothe rightor leftofa sink

• Asquareopeningforproper dishwasheroperation and appearance.

* Acalfmetfruntthatis perpendicular tothe floor.

• 1/4"(.64cm) minimumclearancebetweenmotorand flooringto preventthe

motorfromoverheating.

• The hot water line to the dishwasher must provide between 20-125

psi (138-862 kPa) water pressure.

• The hot water heater should be set to deliver 120°F (49°C)

minimum water temperatureto the dishwasher for best results.

• A3/8" minimum O.D. copper tubing inlet line is recommended.

• Dishwasher inlet valvehas 3/8" N.P.T. internal pipe threads.

• Allsolder connections must be made before water line is connected

to dishwasher inlet valve. Do Not solder within 6 inches (15.2cm)

of inlet valve.

20-(so.san)

The drainhosesuppliedmeetsAHAMDW-iteststandards.

• Thedrainhose musthavea highdrain loop,20 inches (50.8cm)

abovefloor.Thiswillhelp topreventbackflowor watersiphoning

duringdishwasheroperation.

• An'airgap mustbeusedin thehigh drainloop ffthedrain hoseis

connectedtohouse plumbinglowerthan20 inches(50.8cm).

• Thewasteteeor disposerinletmust be20 inches(50.8cm)

minimumabovethe floor.

• Drain hose must be installed towasto tee or inlet above drain trapin

house plumbing.

• Drain line and fittings must be 1/2" minimum I.D.

• ff a longer drain hose is required, the _um length is 12 feet

(3.7m). Check thatdrain hose is resistant to heat and detergent.

Direct wire method

Localcodesmaypermitusingarmored ornon-metallicsheathed,

copper wire(A) (withgroundwire) toconnectdishwasherto

unctionbox.

5. Cuta 3/4"(l.gcm) holeinla_, sideorfloorofcabinet(B) for

directwiring.Rightsideis easiestlocation.

Wood cabinet: Sandholeuntilsmooth.

Metalcabinet: Coverhole withgrommet (Part No.302797)

availablefromyourdealerorpartssupplier.

6. Installa U.L-listed/C_A-certffied strain relinfto the junction box.

If using conduit, use a Ui.-listed/CSA-cer tiffed conduit connector.

Connect the power supply wire to thejunction box. Run the other

end of wire throughcabinet hole (B). The power supply wire

must extend 24 inches (61cm) from the back wall into cabinet

opening.

Power supply cord method

Localcodes maypermit a U.L.-listed/_A-certiffed,16-gauge,power

supplycord (PartNo.4317824) (C) with a three-prong,ground-

typeplug (D) toconnect dishwasherto grounded outlet(E).

5. Cuta 1-1/2"(3.8cm) hole in rear or rightsideofcabinet(F) for

powersupplycord. Rightsideis easiestlocation.

Wood cabinet: Sandholeuntilsmooth.

Metal obinet: Coverholewithgrommet(PartNo.302797)

availablefromyour dealer or partssupplier.

6. Install a matingthree-pronggronnd-typeoudet in anadjacent

cabinet.

Waterline (protect from freezing)

7. CUta 1/2"(1.3cm) minimumhole(G) in cabinetwall orfloor for

water line.Loftsideis easiestlocation.

8. Roughwaterline(H) to the cabinetopening.

9. Installamanualshutoffvalvein the waterlinewhereitcan be

easilyused.

10. Flushwaterlineinto a bucket to getrid ofanyparticlesthatmay

cloginlet valve.Checkthatthere are no sharpbends orldnksin

thewaterlinethatmayrestrictthewaterflow. Turnshutoffvalveto

the "OFF"position.

Drain hose

11. CUta 1-1/2' (3.8on) diameter drain line op_ (I) in the

cabinetwallorfloor.

Adjustthefroutlevelinglegs (E) the numberof turnslistedin the

chart. Thedishwashershouldbe installedas levelas possible from

fronttoback.

Putthe spring-typedrain hose clamp(F) over thedrain connector

(G). Push drain hose (H) onto drain connector. Usepliers to open

clampand slideclamp overdrain hoseand drain connector.Check

thatdrainhoseis securelyattachedtodrain connector.

Tilt dishwasher backwards on wheels when moving across

floor to prevent damage to floor covering.

Latch (I) the dishwasher door. Grasp the sides of the dishwasher door

near the console (J). Tilt dishwasher backwards on wheels. Move

dishwasher close to cabinet opening. Do Not push on the center of

the console. Discardshipping baseor hardboard.

Insertdrain hoseinto holecut intocaFmet. Checkthatdrain hose

doesnot contactdoor springs,motor orwater line.

• Do Notrundrainhoseover topoftub. Checkthatdrain hoseis not

kinkedortwisted.

m I m

__ m

Insert power supply cord into hole cut into cabinet. Ifusing power

supply wire, adjust wire and pull towards dishwasher terminal box.

• Do Not pinch power supply cord or ldnk power supplywire between

dishwasher and cab'met.

Movedishwashercompletelyinto cabinetopening. Centerdishwasher

in opening.Checkthat levelinglegs (K) are firmlyagainstthe floor.

Alignthe dishwasherdoor withfront ofcab'metdoors. Checkthat

spacing(L) isthe sameon bothsides.

Altemate Connection Methods

NoAirGap

Iflocal codespermit,thedishwasherdrainhosemaybe connected

direcOytoawasteteeorwastedispo .

Drain hose (A) to waste tee (B)

Cutdrainendofdrainhose asshown(C). DoNotcotfibbed

sectionto shortendrainhose(D).

Securedrainhose towasteteewithspring-or screw-type

clamp (E). Ifspring-typeclampdoesnotfitsmallersectionof

drain hoseconnector,use a smallerclamp. Smallerdamps are

availableatplumbingsupplystores.

The waste tee connection MUSTbe ahead of the drain

trap (F) and 20 inches (50.8cm) minimum above the

floor(6).

Drain hose (H) to disposer (I)

Knock out disposer inlet plug from inlet 0)- Ifinletplug

fallsinsidedisposer,youmustremoveinletplugbefore

connec_ngdrainhose. Ifdisposeris alreadyinstalledin sink,

youmay needto removedisposer fromsinktoremoveplug.

DONOTcutend ofdrain hose.

Securedrain hosetodisposerwithspring-or screw-type

damp (X).

Mostdisposershave7/8"connectors,or specialconnectorsare

availableatplumbingsupplystores.

The disposer connection MUSTbe ahead of the drain

trap (L) and 20 inches (50.8cm) minimum above the

floor (M).

• InstallaU.L-listed/t_-certiliedstrainrelief(F) to theterminal

box. Runpowersupplywire throughstrainrelief,ffusingconduit,

use a U.L.-listed/CA_-certiffedconduitconnncmr.Runconduit

throughconnector.

• Connectthewhitewire (G) fromthe power supplywiretothe

whitewire intheterminalboxwithtwist-onwire connector.

• Connectthe blackwire (H) fi'omthe powersupplywireto the

blackwirein the terminalboxwithtwist-onwireconnector.

Ifthe ground connector (I) looks like this:

• LoosenfrontnutO) ongroundconnectorlocatedon the backof

terminalbox. DoNotloosenthe rearnut(K) on the ground

connector.

• Formthebaregroundwire (L) into a U-shapedhook. Wrap

groundwire hookclockwisearound groundconnectorand

betweenthe rearandfrontnuts. Securelytightenthefrontnut (J)

overthe groundwire.

• Tightenstrainrelieforconduitconnectorscrews(M).

If the ground connector (i) looks like this:

• LoosenscrewO) onground connectorlocatedonthe backof

terminalbox.

• Formthe baregroundwire (K) intoa U-shapedhook. Wrapground

wire hook clockwisearound groundconnectorand under the

washer(L).Securelytightenthescrew0).

• Tightenswainrelieforconduitconnectorscrews(M).

• Replaceterminalcover(E).

Installation steps cont. on page 9 o

• Connectthewhitewire(Q) fromthe powersupplycordtothe

whitewireinthe terminalbox withtwist-onwireconnector.

• Connectthe black_ (R) fromthepowersupplycordtothe

blackwirein the terminalboxwithtwist-onwireconnector.

Ifthe ground connector (S) looks like this:

• Loosenfrontnut(T) on groundconnectorlocatedonthebackof

terminalbox. DoNotloosenthe rearnut(U) on theground

connector.

• Formthebaregroundwire(V)into aU-shapedhook. Wrap

groundwirehook clockwisearoundgroundconnectorand

betweenthe rearand fi'ontouts. Securelytightenthe frontnot (T)

overthegroundwire.

• Tightenstrainreliefscrews(W).

ffthe ground connector (S) looks like this:

• Loosenscrew (1")onground connectorlocatedontheback of

terminalbox.

• Formthebaregronndwire (U) into a U-shapedhook Wrap

groundwirehookclockwisearound groundconnectorand under

thewasher(V). Securelytightenthe screw(T).

• Tightenstrainreliefscrews(W).

Illl

m I

(o_1

• Replaceterminalcover(0).

• Plug power supply cord (X) into mating grounded outlet (Y).

Opendoor about 3inches (7.6cm) and checkfor equalspacing(C)

betweeninnerdoor and tubsides. If spacingis notequal,loosen

bracket screwsand shifttub. Tightenbracket screws.Remove

newstraperor towelfromdishwasher.

Openand closedoor severaltimes.Thedoorshouldopenand close

easily.Ifdoor doses too quicklyorfallsopen,adjust door

springs(D) bymovingspringendstodifferentholes (£) inbase.

accessandlowerpaneltodishw_herso thatthebottomedge

ofthelowerpanelcontactsthe floor.

Your installation is now complete.

Keep Installation Instructions and Use and Care Guide

close to dishwasher for easy reference.

Your safety and the safety of others

is very Important.

We have provided many important safety

messages in this manual and on your appliance.

Always read and obey all safety messages.

This is the safety alert symbol. This symbol

alerts you to hazards that can kill or hurt

you and others. All safety messages will be

preceded by the safety alert symbol and the word

"DANGER" or "WARNING". These words mean:

You will be killed or seriously Injured if you

don't follow instructions.

You can be killed or seriously injured if you

don't follow instructions.

All safety messages will identify the hazard,

tell you how to reduce the chance of injury, and tell

you what can happen if the instructions are

not followed.

• Observe all governing codes and ordinances.

• complywiththeinstallationspecificationsand dimensions.

• properlyinstalldishwasher.

• makesure youhaveeverythingnecessaryforproper installation.

• contacta qualifiedinstallertoinsure thatthe electricalandplumbing

installationsmeet allnationaland localcodes andordinances.

Keep cardboard shipping base or hardboard under

dishwasher until it is installed. The shipping base or -

hardboard will helpIo protect floor covering when

dishwasher is moved across the floor during installation.

Introduction cont.from page2

MODELS A

MODI_LIES

KUDC Series

Stifle KUDC 24-1/4" (61.6 ore)

10UDI25 Series 61,6 cta (24-1/4 po)

Sl_de KIJDI25

All Others 25-1/4" (64.1 an)

TOllS lea anwes 64,1 can (25-1/4 po)

* does not include insulation bhmket

* ne comprend pas l'isolant

35-7.'8"

(_) a_.

91- 24"(61cm)* --

19-3/4" (50.2{_)*

Opening for electrical, drain and water supply lines:

• Mustbeinstalledwithintheshaded area as specified.

• Shouldbe located as close to the rear wallas possible.

Electrical outlet must be installedin an adj_cut cabinet.

Wiring should not contact the motor or dishwasherlegs.

Water line: CutI/2"(1.3cm) diameteropening.

W_ter line Must Not contact the motor or dishwasher legs.

Drain line and power supply cord: Cut I-I/2"(3.8cm) diameter opening.

Direct wire electrical suppl],: Cut 3/4"(1.9cm) diameteropening.

Install a grommet (Part No. 302797) in opening cut in a metal cabinet for

power supply cord orpower supplycable.

Dishwashermust be completely enclosed, sides, top and rear.Side panel ldts

are available fromyour dealer for installing yourdiswasher at the end of a

cabinet.

Bl_k, Part No. 4378868

White,PartNo. 4378867

Almnnfl P_rt MO _TP_ql_Q

Ill

It is the customer's responsibility:.

To contact a qualified electrician.

Toassure thatthe electrical installation is adequate and in

conformancewith all national and local codes and

ordinances.

Dishwashermust be connectedtotheproperelectricalvoltageand

flequencyasspecifiedonthemodel/serialratingplate.Themodel/serial

ratingplateis locatedbehindthedoor on thefrontframeof the

dishwasheropening.

• CONNECTWITHCOPPERWIREONLY.

• 120-volt, 60-Hz, AC-unly,15-ampere, fused electrical supply is

required.

• Atime-delayfuse or circuit breaker is recommended.

• It is recommended that a separate circuit servingonly thisappliance

be provided.

• Some models are already equipped with a power supplycord. If a

power supply cord is not supplied, Power Supply Cord Kit (Part No.

4317824) is available from your local dealer or parts supplier. Follow

the kit instructions for installing power supply cord.

If the kit is not available locally, use a U.L-listed/CA*_-certified,three-

conductor, 16-gauge, six foot, power supply cord thatmeets all local

codes and ordinances. It must be routed so itdoes not touch the

dishwashermotor or lower portion ofthe dishwasher tub. Aswain

reliefmust be used to secure the power supply cord to the dishwasher

terminal box. The power supply cord must be plugged into a mating

3-prong, ground-type oudet, grounded in accordance with allnational

and local codes and ordinances.

• Ifapowersupplycord is attachedtodishwasherbutyouneed to direct

wiredishwasher,youwillneedDirectWireConnectionKit(Part No.

4317979). Removepowersupplycordand makealldirectwire

connectionsinsideterminalbox. Allelectricalconnectionsmustbe

madein accordancewithallnationaland localcodesandordinances.

• Dishwashermustbeconnectedtoagroundedmetal,permanent

wiringsystemor a groundconductorcan beusedwiththedt_-'uit

conductorsto connectto thegroundterminalor leadonthe

dishwasher.

• Do notgroundto a gaspipe.

• Do notconnectdishwashertoelectricalsupplyuntildishwasheris

permanentlygrounded.

• Donothaveafusein theneutralor groundcircuit.

24,,'''_

(61_m)

ElectricalShock Hazard

Disconnectelectricalpowerat thefuse box

or circuit breakerbox beforeinstalling

dishwasher.

Failuretodo so can result in death or

electricalshock.

1.Disconnectthepower supply.

2. Putonglovesandsafetyglasses.

Electrical

3. Pickone methodto follow("Directwire" or "Powersupplycord"),

dependinguponyourdishwasherand local codes.

4. Completewiringto cabinetopeningaccordingtowiring_nethodyou

need. Followalllocalcodes and ordinances.

Tip OverHazard

Do not usedishwasheruntilcompletely

installed.

Do notpush downon open door.

Doing socan resultin seriousinjuryor cuts.

Excessive Weight Hazard

Usetwo or morepeopleto move and Install

dishwasher.

Failureto do socan resultin backor other injury.

Keep cardboard shipping base or hardboard under

dishwasher until it is installed. The shipping base or

hardboard will help to protect floor covering during

installation.

Removethefour screwsattachingaccess panel(A) andlowerpanel

(B) todishwasherusinga 1/4"hexsocket, nut driveror PhiLlips

screwdriver. Removepanelsand set panelsaside on aprotective

surface.

Mill,

Cutout

"" Height

34"(s6.4cm)

34-1/8" (86.7c_m)

34-5/16"(87.2cm)

34-1/2"(87.6_n)

For additional height:

1. Addshims under the wheels.

Wheel Number Of Turns

Position To Adjust

(See Illustration) Levelers

1 9

2 6

3 3

4 0

2. Turn front levelers (each turn is approximately 1/16"

(1.6ram) in height).

Measureheightofcabinetopening(C) fi'omundersideofcountertop

tofloor. Checkchartforthatheightopening. Putwheels(D) inthe

requiredposition,

(I r ! I'1

Connectdrainhoseto an air gaporwasteteeusing one of the

recommendedoralternatemethods.

Recommended Connection Methods

Install Air Gap Kit (Part No. 300096) (A) according to kit

instructions. If a different air gap is used, it should be checked to

make sure it allows for the same air flow.

Drain hose (B) to air gap (A) to waste tee (C)

Cutdrain cod ofdrainhose asshown(D). Do Notcut ribbed

sectionto shortendrainhose (E).

,t,

Securedrainhose toairgapwithspring-typeclamp(F). If

spring-typeclampdoesnotfit smallersection ofdrainhose

connector,usea smallerclamp. Smallerclampsareavailableat

plumbingsupplystores.

Connectthe airgap towastetee usinga rubberconnector(G)*

andspring-orscrew-typodamps (H).

The waste tee connection MUSTbe ahead of the drain

trap (I) and 20 inches (50.8om) minimum above the

floor O).

Drain hose (K) to air gap (L) to disposer (M)

Knock out disposer inlet plug (N) from inlet. Ifinletplug

fallsinsidedisposer,youmustremoveinletplugbefore

connectingdrainhose. Ifdisposeris alreadyinstalledin sink,

youmayneedto removedisposerfromsinkto removeplug.

DONOTcutendofdrainhose.

Securedrainhosetoair gapwithspring-typeclamp(0).

Connectthe airgapto disposer usinga rubberconnector (P)*

andspring- or serew-typoclamps(Q).

Mostdisposershave7/8"connectors,orspecia]connectorsare

availableatplumbingsupplystores.

The disposer connection MUSTbe ahead of the drain

trap (It) and 20 inches (50.8cm) minimumabove the

floor (S).

* All parts are available from your dealer.

ApplyTeflontapeto90° elbowfitting(A) andconnectfittingdirectly

towaterinletvalve(B). Attachwatersupplyline(C) to fitting.

Do Not allow the waterpipe or tubing to contact the motor or

dishwasher legs (D). Turnonwatersupplyand check forleaks.

Check electrical requirements. Be sure you have correct

electrical supply and recommended grounding method. See

Page 4.

If connecting dishwasher using direct wire method,

check that power supply is disconnected.

ElectricalShockHazard

Electricallygrounddishwasher.

Connectgroundwiretogreengroundconnectorinterminal

box.

Donot useanextensioncord.

Failuretodosocanresultindeath,fire,orelectricalshock.

• Removethedishwasherterminalboxcover (E).

TipOver Hazard

Do not usedishwasheruntilcompletely

installed.

Do not pushdown on opendoor.

Doingso canresultin serious injuryor cuts.

Opendishwasherdoor and removeall shippingmaterials. Remove

bottomrzck Placenewspaper (A) or toweloverbottom of

dishwashertopreventscrewsfromfallingintopumparea when

securingdishwasherto countertop.

ThedishwasherMUSTbe secured to countertoporfloorto keepit

fromtippingwhendooris opened.

Countertopattachment: Secure dishwasherto counter_p withtwo,

No. 10x 1/2"Phillips-headscrews(it).

DoNotdropscrewsintothe bottomofthedishwasher.Screws,if

droppedinpumparen,maycausedamageto pumpormotur.

Floor attachment: Usefloorattachmentkit (Part No.4378968)

availablefromyourdealer.

Page is loading ...

KitchenAid 9743822 User manual

Brand: KitchenAid

Model: 9743822

Category: Dishwashers

Type: User manual

This manual is also suitable for

Download PDF

report

KitchenAid 9743822 User manual

This manual is also suitable for

KitchenAid 9743822 User manual

Related papers

Other documents