Ferm WSM4002 User manual

Brand: Ferm

Model: WSM4002

Type: User manual

0310-16

Overheating

- The ventilation slots are blocked with dirt.Clean with

dry cloth.

- The machine does not start when switched on. Check

the mains lead and the fuse/plug.Take to your Ferm

Dealer for repair

- The motor is defective.Take to your Ferm Dealer.

MAINTAIN TOOLS WITH CARE

Keep the tool clean for better and safer performance.

Store the discs properly in accordance with the maker’s

instructions.

Follow instructions for changing accessories.Inspect tool

and extension cables periodically and if damaged, have

them repaired by a qualified person or authorised service

body.Keep handles free from oil or grease.Keep the venti-

lation slots clean to prevent motor overheating.

Check for damaged parts

Do not use a tool with damaged parts,before further use a

damaged tool must be carefully checked by a qualified per-

son to determine that it will operate properly.Check for

alignment of moving parts, binding or breakage of parts,

mounting and other conditions that may affect its opera-

tion.

A damaged part or guard should be properly repaired by

an authorised service centre, unless indicated otherwise

in the instruction manual.Have defective switches repla-

ced by an authorised service centre. Do not use a tool if

the switch does not turn on and off.

Have your tool repaired by an expert

This appliance is manufactured in accordance with rele-

vant safety standards.Only experts must carry out repai-

ring of electrical appliances,otherwise considerable dan-

ger for the user may result.

Storing tools

When not in use tools should be stored in the dry,out of

reach of children.

ELECTRICAL INFORMATION

This product is complete with a pre-wired mains plug,it is

double insulated in accordance with EN 50144 – no earth

wire is required

If the plug needs replacing follow these instructions.

Wire correctly

The wires in the mains lead are coloured in the following

way:

BLUE -Neutral

BROWN -Live

Securing wires

Secure wires carefully and firmly to the correct terminals.

Secure the mains cable in the plug cord grip firmly.

Fit a 13-amp fuse. If a 13amp (BS1363) plug is used a (BS

1362) ASTA approved 13-amp fuse must be fitted.

Recycle/Dispose of old plug and cable

Prevent inadvertent connection to socket and risk of elec-

tric shock.

ENVIRONMENT

Recycle the packaging according to the identification

marks on it.

At the end of the product or its accessories life please re-

cycle where facilities exist - phone the Helpline for cur-

rent advice on recycling.

Helpline

For any questions relating to operational or safety

matters contact:

Ferm Customer Helpline on: 0115 966 1199

Monday-Friday 8am – 6pm

Saturday 9am – 1 pm

GUARANTEE

The guarantee conditions can be found on the separately

enclosed guarantee card.

We declare under our sole responsibility that this

product is in conformity with the following

standards or standardized documents

EN-50144-1,prEN50144-2-3,

EN-55014-1,EN-55014-2,

EN61000-3-2,EN61000-3-3,

in accordance with the regulations:

98/37/EEC

73/23/EEC

89/336/EEC

from 01-12-2001

GENEMUIDEN NL

W. Kamphof

Quality department

DECLARATION OF CONFORMITY

(

)

Blue

(Neutral)

Green & Yellow

(Earth)

Brown

(Live)

Fuse

(13 Amp)

INSTRUCTIONS FOR USE

FWS-125KN

WALL CHASER

Art.nr. WSM4002

FWS-125KN

152

FWS-125KN

GENERAL

Congratulations!

With the purchase of this high quality Ferm tool, you

have made an excellent choice. Ferm products are

rugged, safe and easy to use.

It is very important to exercise care when handling

and servicing this tool. Please read these instructions

thoroughly, and be sure to follow the directions given.

You will then enjoy many years of service from your

Ferm tool.

Package contents

• Electric wall chaser

• Handgrip

• Diamond cutting discs (2 x)

• Cam wrench

• Hex key

• Cold chisel

• Dust extraction adapter

• Set carbon brushes

• Instructions for use

• Guarantee card

Product information

Safety Instructions

In these instructions for use, the following symbols

are used:

Caution: risk of bodily harm, fatality or da-

mage to the machine, from failure to follow

the directions in these instructions for use.

Caution: electrical current.

The machine is double insulated compliant

with EN50144; therefore no earth connecti-

on is required.

Visual check before starting to work

Specifications

Voltage 230 V~

Frequency 50 Hz

Power rating 1300 W

Rotational speed (not loaded)

9000/min

Max.cutting depth 8-30 mm

Max.channel width 8- 26mm

Weight 4,2 kg

Cutting disc (2x) Ø125 x 22,2 x 2,0

Lpa (Sound pressure level) 90,9 dB(A)

Lwa (Sound power level) 103,9 dB(A)

Vibration level 0,9 m/s

1. On/off trigger switch

2. Attachment point for

handgrip

3. Connection for

mechanical dust

extraction

4. Guide wheel

5. Distance washers

6. Spindle nut

7. Cutting depth fixing

knob

8. Cutting direction

9. Shaft lock

MAITENANCE AND REPAIR

Overview spare parts

MAINTENCE,CARE AND

REPAIR

Switch off and unplug the machine before carrying

out any cleaning or maintenance work.

CLEANING

Do not use flammable liquids to clean the angle grinder,

FAULTS

Switch OFF immediately at the mains plug and

remove the plug when:

- The plug or cable is damaged.

- The switch on the machine is defective.

-You smell or see smoke caused by scorched insulation

in the machine.

GENERAL SAFETY INSTRUCTIONS

FWS-125KN

Caution!

Whenever working with electric tools, always take

basic safety precautions including those described

below, to reduce the risk of fire, electric shock, and

personal injury.

Before using the product, read all safe use directions

and keep them in a handy place.

Directions for safe use:

1 Keep the working environment tidy

• Untidy workplaces and benches can easily cause

accidents.

2 Be alert to the conditions in your surroundings.

• Do not expose electric tools to rainwater.

•Never use electric tools in damp or wet condi-

tions.

• Ensure that the work area is well lit.

•Never use electric tools where there is a hazard of

combustion or explosion.

3 Protect yourself from electric shock

•Avoid bodily contact with earthed surfaces (such

as pipes, radiators, heaters, refrigerators).

4 Keep children at a safe distance

• Do not allow bystanders to touch the tool or ex-

tension cord.

• Do not allow bystanders access to the worksite.

5 Store tools, which are not in use

• Store tools, which are not in use, in a dry, high, or

lockable place, beyond the reach of children.

6 Do not overload the tool

• For a good and safe result, use the tool settings

advised.

7 Use the right tool for the job

• Do not use light tools or accessories for heavy du-

ty jobs.

• Never use the tool for work it was not designed to

do. For example, do not use a circular saw to saw

branches or cut down trees.

8 Wear suitable work clothing

•Wear no loose clothing or jewellery, as these

could become entangled in moving parts of the

machine.

• When working outdoors, rubber gloves and foot-

wear with heavy profile soles are recommended.

•Wear a headband or hairnet to keep long hair out

of the danger zone.

9 Wear safety glasses

• When your work generates dust, wear a dustmask

or facemask.

10 Connect a dust extraction system

• If the tool provides for connection to a dust

extraction system, ensure that this is connected

and working correctly.

11 Only use the power cord for its intended use

• Never carry the tool by its power cord, and do not

unplug the tool from the power by pulling on the

power cord.

•Protect the power cord from heat, oil, and/or

sharp edges.

12 Do not overextend yourself

• Ensure you have secure footing, and maintain

your balance at all times.

13 Maintain the tool with care

• Keep cutting equipment sharp and clean, so you

will achieve a good result, safely.

• Follow the directions for lubrication and replace-

ment of parts.

• Inspect the power cord regularly and have a da-

maged cord repaired by an authorised service

agent.

• Inspect extension cords regularly, and replace

any damaged cords.

•Keep handgrips dry, clean and free from grease

and oil.

14 Remove the plug from the wall socket

•Whenever the tool is not in use, and before ex-

changing parts such as blades, bits and knives.

GENERAL SAFETY INSTRUCTIONS

1. Maintain the tool with care.

• Keep the tool clean and sharp.

• Follow the directions for lubrication and fitting of

accessories.

• Periodically inspect the power cord, and have any

damage repaired by an authorised service agent.

• Periodically inspect extension cords, and replace

them if damaged.

• Keep handgrips dry, clean and free from grease

and oil.

2. Always remove the plug from the mains, whene-

ver:

• the machine is not in use;

• you service the machine;

• exchanging accessories such as blades.

3. Immediately repair any damage.

Regularly inspect all moving parts, attachments

and all other parts that can affect correct opera-

tion.

• Have all repair work carried out by an authorised

service agent.

MAITENANCE AND REPAIR

Malfunctions

Problem

The electric motor becomes hot

and cuts out.

The machine switched will not

run.

Cutting is difficult and the channel

made is irregular.

When cutting, the workpiece be-

gins to vibrate heavily

The machine runs erratically

and/or noisily.

Possible cause

The overheating protection has been

activated.

The motor is defective.

The overload protection has been acti-

vated.

The overheating protection has been

activated.

The switch is damaged.

The cutting discs are bent or blunt.

The cutting discs are overheated or de-

formed.

The carbon brushes are worn.

Solution

Wait several minutes until the machi-

ne has cooled down, then re-start the

machine.

Take the machine to your Ferm dealer

for inspection and/or repair

Re-start the machine.

Wait several minutes until the machi-

ne has cooled down, and then re-

start the machine.

Take the machine to your Ferm dealer

for inspection and/or repair

Replace the cutting discs.

Take the machine to your Ferm dealer

for replacement of the carbon brush-

es.

FWS-125KN

15 Remove adjustment tools and wrenches

• Make it a habit to never switch on the machine, un-

til you have checked that any adjusting tools or

wrenches have been removed.

16 Avoid unintentional starting

•Never carry a connected machine with a finger on

the switch. Make certain that the switch is in the

“OFF” position, before connecting the machine to

the power supply.

17 Use outdoor extension cords

• Whenever you use the tool outdoors, always use

extension cords specifically designed for out-

door use.

18 Stay alert

•Watch what you are doing. Use your common

sense. Do not use the tool when you are tired.

19 Inspect damaged parts

• Before making further use of the tool, if any safety

feature such as a protective cover or other part

has been damaged, make absolutely certain that

the machine is still safe to use, and that the part

can still perform its protective function.

• Check the alignment and free movement of mo-

ving parts, possible breakage of parts, attach-

ments and any irregularities that could adversely

affect operation.

•A safety cover or any other damaged part should

be properly repaired or replaced by an authorised

service agent, unless otherwise directed in these

directions.

•Have any defective switches replaced by an au-

thorised service agent.

•Never use the tool whenever the tool cannot be

switched “ON” or “OFF” with its own switch.

20 Caution

•Use of any part or accessory, other than descri-

bed in these instructions for use, may possibly le-

ad to bodily injury.

21 Have your machine repaired by a qualified service

agent

• This electric tool is manufactured in conformance

with the relevant safety requirements.

Only a qualified serviceman using original spare

parts should carry out repairs, as inexpert repair

will cause considerable risk for the user.

Use

Cutting of channels in materials such as concrete,

masonry and paving, without the use of water, with a

guide wheel.

Never drill, cut or chase in surfaces, in

which electrical cabling, gas or water pipes

could be concealed. Always use a suitable

detector to seek out concealed wiring or piping, or

obtain advice from the local energy or water compa-

ny.

GENERAL SAFETY INSTRUCTIONS USING THE TOOL

Switching on and off

230 V

50 HZ

01 02

03 04

FWS-125KN

FITTING AND ADJUSTMENT INSTRUCTIONS

Fitting cutting discs

USING THE TOOL

Cutting channels

07 08

3 x

Fitting cutting discs Cutting channels

FWS-125KN

FITTING AND ADJUSTMENT INSTRUCTIONS

07 08

3 x

USING THE TOOL

01 02

03 04

05 06

FWS-125KN

FITTING AND ADJUSTMENT INSTRUCTIONS

Adjusting channel width

FITTING AND ADJUSTMENT INSTRUCTIONS

Connecting dust extraction

X + 5 mm

3 x

03 04

05 06

FWS-125KN

FITTING AND ADJUSTMENT INSTRUCTIONS

Adjusting channel width

FITTING AND ADJUSTMENT INSTRUCTIONS

Adjusting channel depth

X + 2 mm

07 08

09 10

3 x

X + 2 mm

X + 5 mm

Ferm WSM4002 User manual

Ferm WSM4002 User manual

Related papers

Other documents