Binary B-500-MTRX-230-8x8 Installation guide

Brand: Binary

Model: B-500-MTRX-230-8x8

Category: Supplementary music equipment

Type: Installation guide

This manual is also suitable for

B-500-MTRX-230-4x4

Binary™ HDMI Matrix Switcher

with HDMI and HDBaseT Outputs

Installation Manual

B-500-MTRX-230-4x4 Installation Manual

Pg. 2

™

1. Important Safety Instructions

 Toreducetheriskofreorelectricshock,donotexposethisapparatustorainormoisture.Donot

removecover.Nouserserviceablepartsinside.Referservicingtoqualiedservicepersonnel.

Thelightningashwitharrowheadsymbol,withinanequilateral

triangle, is intended to alert the user to the presence of

un-insulateddangerousvoltagewithintheproduct’senclosure

thatmaybeofsufcientmagnitudetoconstituteariskofelectric

shock to persons.

Theexclamationpointwithinanequivalenttriangleisintended

to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature

accompanyingtheappliance.

1. Readandfollowallinstructionsandwarningsinthismanual.Keepforfuturereference.

2. Do not use this apparatus near water.

3. Cleanonlywithadrycloth.

4. Donotblockanyventilationopenings.Installaccordingtomanufacturer’sinstructions.

5. Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stovesorotherapparatus(including

ampliers)thatproduceheat.

6. Donotoverridethesafetypurposeofthepolarizedorgrounding-typeplug.Apolarizedplughastwoblades-one

widerthantheother.Agroundingtypeplughastwobladesandathirdgroundingprong.Thewidebladeorthe

thirdprongisprovidedforyoursafety.Iftheprovidedplugdoesnottintoyouroutlet,consultanelectricianfor

replacementoftheobsoleteoutlet.

7. Protectthepowercordfrombeingwalkedonorpinchedparticularlyatplug,conveniencereceptacles,andthe

pointwhereitexitsfromtheapparatus.

8. Onlyuseattachments/accessoriesspeciedbythemanufacturer.

9. Referallservicingtoqualiedservicepersonnel.Servicingisrequiredwhentheapparatushasbeendamagedin

anyway,suchaswhenthepower-supplycordorplugisdamaged,liquidhasbeenspilledorobjectshavefallen

intotheapparatus,theapparatushasbeenexposedtorainormoisture,doesnotoperatenormally,orhasbeen

dropped.

10. DONOTEXPOSETHISEQUIPMENTTODRIPPINGORSPLASHINGANDENSURETHATNOOBJECTS

FILLEDWITHLIQUIDS,SUCHASVASES,AREPLACEDONTHEEQUIPMENT.

11. TOCOMPLETELYDISCONNECTTHISEQUIPMENTFROMTHEACMAINS,DISCONNECTTHEPOWER

SUPPLYCORDPLUGFROMTHEACRECEPTACLE.

12. THEMAINSPLUGOFTHEPOWERSUPPLYCORDSHALLREMAINREADILYOPERABLE.

Warning:

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRICAL SHOCK.

DO NOT REMOVE COVER. NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

B-500-MTRX-230-4x4 Installation Manual

Pg. 3

www.snapav.com Support: 866.838.5052

1. Important Safety Instructions

2. Product Overview

3. Package Contents

4. Features

5. Recommended for Installation

6. Device Layout

 6.1.FrontPanel

 6.2.RearPanel

7. Installation Setup

 7.1. BasicInstallationDiagram

7.2. Basic Instructions

 7.3. InstallationTips

 7.4. SwitcherLocationandPlacement

  7.4.1. RackInstallation

7.5. HDMI Input Connections

7.6. Output Connections

7.6.1. Choosing the Correct Output

7.6.2. HDMI Outputs

7.6.3. HDBaseT Outputs

 7.7.MatrixControlConnections

  7.7.1. IRControl

  7.7.2. RS232Control

 7.8.IRPass-ThroughInstallationandSetup

  7.8.1. MatrixSwitcherIRConnections

  7.8.2. MatrixSwitcherIRPortConguration

 7.9. B-500-RX-230-IRIRConnections

  7.9.1. IRReceiver

  7.9.2. IRFlasher

  7.9.3. YellowTagIRAdapter

 7.10.IRApplicationDiagrams

  7.10.1.IRPass-ThroughfromControlSystem

  7.10.2. IRPass-ThroughfromRoomstoSources

8. EDIDConguration

8.1. Source Setup

 8.2.DisplaySetup

 8.3. AutoEDIDConguration

  8.3.1. HowtoCongureAutoEDID

 8.4.EmbeddedEDIDConguration

  8.4.1. EmbeddedEDIDChart

  8.4.2. HowtoSetEmbeddedEDIDforaSingleInput

  8.4.3. HowtoSetEmbeddedEDIDforAllInputs

 8.5.EDIDLearning

  8.5.1. HowtoLearnEDIDtoaSingleInput

  8.5.2. HowtoLearnEDIDtoaAllInputs

 8.6.ViewingInputEDIDStatus

9. AdvancedSetupUsingtheCongurationUtility

 9.1.IRSourceRouting

 9.2.IRFrontPanelIREnable

 9.3.MatrixControlfromRoomEnable

 9.4.FrontPanelPowerButtonActive

10. Firmware Update

11. Operation and Control

 11.1.IRRemote

  11.1.1.RouteInputstoOutputs

  11.1.2.TurnOff(Mute)Outputs

  11.1.3.DisplayOutputStatus

  11.1.4.ResettingtoFactoryDefaults

12. Troubleshooting

 12.1.GeneralTroubleshootingGuidelines

 12.2.NoSignalfromSourcetoanyDisplay

 12.3.NoSignalfromanySourcetoanDisplay

 12.4.Audioissues

13. Contacting Tech Support

14. System Layout Chart

15. Specications

16. Warranty

Table of Contents

B-500-MTRX-230-4x4 Installation Manual

Pg. 4

™

2. Product Overview

Welcome to Binary™, one of the most highly regarded brands available today. This product is engineered to

provide years of exceptional reliability. We appreciate your business and we stand committed to providing our

customerswiththehighestdegreeofqualityandserviceintheindustry.

TheB-500-MTRX-230-4x4isastate-of-the-artHDMImatrixswitcherwithbothHDMIandHDBaseTOutputs.Itprovides

truematrix routingforHDMIsignals.WithfeaturessuchasHDMI3Dsupport,sophisticatedEDIDhandling,IR,and

RS232,thisproductisidealforresidentialandcommercialmediadistributionsystems.TheHDBaseTconnectionon

eachoutputextendsHDMIsignalsandbi-directionalIRtoremoteroomsupto230feetawayviaCat5e/Cat6/Cat6a.

Note: This manual covers all aspects of installation and setup of the B-500-MTRX-230-4x4 for most applications. Some

features must be congured using the Conguration Utility software. Go to the product page for the B-500-MTRX-

230-4x4 at www.SnapAV.com and click on the Support Tab to download the Conguration Utility and manual.

4. Features

• (4)HDMIinputsby(4)mirroredHDMIandHDBaseToutputs

• Upto8displayscanbeattachedintotal(usingbothHDMIandHDBaseToutputs)

• SupportsVideoresolutionsupto1080p/6036bitcolor

• SupportsallHDMIaudioformatsincludingDolbyTrueHDandDTSMasterHD

• SupportsallHDMI3Dformats

• SophisticatedEDIDhandlingincludingEmbedded,Learned,andAutomodes

• HDMIorDVIwithadapter(notincluded)

• IRControlfromintegratedreceiveror3.5mminput

• Bi-directionalIRpass-throughwhenusingB-500-RX-230-IR

• HomeAutomationControlviaIR,andRS-232

• PCSetupandCongurationusingdedicatedsoftware

• HDCP2.0compliant

• CECPassThrough

5. Recommended for Installation

• PhillipsScrewdriver(forrackearattachment)

• Upto4sources

• Upto4displays(8ifusingbothHDBaseTandHDMIoutputs,seeSection7.6,Page9)

• BinaryHighSpeedHDMICablestoconnectsourcestoB-500-MTRX-230-4x4HDMIinputs

• BinaryHDMIcablesorB-500-RX-230-IRunitsandCat5e/6cableinstalledbetweenmatrixswitcherlocationand

displays(Seesection7.6.3.1,page10forHDBaseTwiringrecommendations)

• RJ45connectorsandterminationtools(IfusingB-500-RX-230-IR)

• ControlSystemtocontroloperationofB-500-MTRX-230-4x4

• WindowsPCwithCongurationUtilityinstalledandRS232adapter

• CongurationUtilityManual

3. Package Contents

• (1)B-500-MTRX-230-4x4

• (2)Rackearsformounting(screwsincluded)

• (1)IRRemoteControl

• (1)Powersupply24V2.7ADC

• (1)InstallationManual

• (1)CD-ROM

B-500-MTRX-230-4x4 Installation Manual

Pg. 5

www.snapav.com Support: 866.838.5052

6. Device Layout

6.1. Front Panel

1. Power On/Off Switch

 TogglePowerfromOntoStand-by.CanbedisabledfromCongurationUtilitysoftware.

2. Source Status LEDs

 IndicatesthattheselectedsourceisonandtransmittinganHDMIsignal.

3. Output Display

 Displaysthelastoutputselected.

4. IR Receiver Window

 IRreceiverforMatrixtocapturecommandssentbyIRremote.

5. Input Display

 Displaysthelastinputselected.

1 2

B-500-MTRX-230-4x4 Installation Manual

Pg. 6

™

6.2. Rear Panel

1. HDMI Inputs 1 through 4

 ConnectHDMIcablesfromsourcestothematrixswitchfordistribution.

2. RS-232 control port (DB9)

 AttachconnectionfromcontrolsystemorWindowsPCforserialcontroloftheB-500-MTRX-230-4X4.

3. IR Output to Source 1 through 4

3.5mmmonominiconnectionsusedtoconnectIRashersforcontrollingsources.Theseportsmaybeconguredto

routecommandsonlyfromtheIRoutputcorrespondingtotheHDBaseToutputnumber(IRzonerouting),ordirectly

tothesourceselectedforviewingonanHDBaseToutput(IRsourcerouting).(SeeCongurationUtility)

4. RJ45 HDBaseT Outputs 1 through 4

Connect568BterminatedCat5e/6HDBaseTcableroutedtoaB-500-RX-230-IRupto230feetawaytofeedHDMI

signaltodisplay.OutputsimultaneouslydisplaysthesamesourceastheHDMIoutputofthesamenumber.

5. Link LED

 ThegreenLinkLEDsindicatethestatusoftheHDBaseTconnection.Off=Nolink;On=Linkisactive.

6. HDMI Outputs 1 through 4

 ConnectHDMIcablestoroutetodisplays.OutputsimultaneouslydisplaysthesamesourceastheHDBaseToutput

ofthesamenumber.

7. IR Input to Room 1 through 4

 3.5mmmono-miniconnectionforIRpass-through.ConnectthecontrolsystemIRFlasheroutputstosendcommands

todisplaysorotherdevicesintheroom(onlywhenusingtheB-500-RX-230-IRtoextendtodisplays).

8. System All IR Out

 3.5mmmonominiport,repeatsallIRcommandsfromallconnectedHDBaseToutputs(fromIRReceiverportof

B-500-RX-230-IR).

9. System IR In

 3.5mmmonominiIRinputportformatrixcontrol.

10. Latch-Locking Power Jack

 24V2.7ADCpowersupplyportwithlockingscrewcollarforsecureconnection.

LINK LINK LINK LINK

1 3

2 4

1 3

2 4

24V DC 2.7A

2 3 4 7 8 1061 95

B-500-MTRX-230-4x4 Installation Manual

Pg. 7

www.snapav.com Support: 866.838.5052

7. Installation and Setup

7.1. Basic Installation Diagram

7.2. Basic Instructions

1. Unpackthematrixandinstallitnearthesourceequipment.(7.4.SwitcherLocationandPlacement,page8)

Note: Do not power the matrix switcher until it is indicated to do so.

2. InstallandconnecteachsourcetoaninputonthematrixswitcherusingtheshortestHDMIcablepossible.

 (7.5.HDMIInputConnections,page9)

3. InstallthedisplaysandoutputwiringtothematrixlocationusingHDMIcablesforstandardHDMIoutputorCat5e/6

ifB-500-RX-230-IRReceiverswillbeused.(7.6.OutputConnections,page9)

4. RecordtheinputsandoutputsusedintheSystemLayoutChartforfuturereference.

 (14.SystemLayoutChart,page26)

5. Ifusingacontrolsystem,connectittotheappropriateportonthematrixswitcherforthedrivertypebeingused:

IRorRS232control.(7.7.MatrixControlConnections,page11)

6. Installandcongurethedriverformatrixswitchingcontrolintothecontrolsystemprocessor.

 (7.7.MatrixControlConnections,page11)

7. InstalltheIRequipmentandsetupIRpass-throughifusingit.

 (7.8.IRPass-ThroughInstallationandSetup,page12)

8. Attachthepowersuppliestothematrix,sources,anddisplays,thenpowerupthesystem.

9. Testallinputandoutputselectionsforsync,reliableswitching,correctaudioformatandvideoresolution.Usethe

factoryremoteortheMatrixCongurationUtilitytosetupEDIDsasneeded.(8.EDIDConguration,page16)

10. ChangeanyadvancedsettingsintheMatrixCongurationUtilityasneededtosuittheinstallation.

 (9.AdvancedSetupUsingtheCongurationUtility,page20)

Completethebasicinstallationsectiontosetupthematrixswitcherformediadistributionbeforecompletinganyother

setup.Usethisdiagramforreferenceduringbasicinstallationofthematrixswitcher,sources,displaysandwiring.

Thesearethebasicstepsthatmustbetakentoconnectequipmenttotheinputsandoutputsofthematrixswitcherand

congurethesystemforuse.Seethesectionslistedforfullinformationoncompletingeachstep.

LINK LINK LINK LINK

1 3

2 4

1 3

2 4

24V DC 2.7A

Projector

Game

Console

HDTV HDTV HDTV

HDMI

HDMi

HDMI

B-500-RX-230-

Cat5e/6

HDMI

Home Automation System

Blu-ray Player Cable/Sat Box

AC Power

RS232

B-500-MTRX-230-4x4 Installation Manual

Pg. 8

™

7.3. Installation Tips

7.4. Switcher Location and Placement

Followingthesetipsduringtheinstallationprocesswillhelpguaranteeasuccessfulinstallation.

• Testeverycablebeforeuse.

 Alwaystestcablesbeforeuse.Field-terminatedcablesshouldbecheckedforcontinuityafterterminationtobesure

theconnectorswereinstalledcorrectly.

• Labeleachcableasitisinstalled.

 Thiswillaidinconnectionsetupandprogramming,andwillalsomakeiteasiertocomebacktoajobatalaterdate

andimmediatelyknowwhatisconnectedwhere.

• CompletetheSystemLayoutChart(page26)inthebackofthemanualduringinstallation.

 Recordthesourceconnectedtoeachinput,theoutputnumberofeachdisplay,andthemethodofroutingsignalin

thechartforreferenceduringinstallationandsetup.Useitafterwardtokeeptrackofequipmentinuse,openports

forexpansion,andtohelpidentifywheretotroubleshootissuesiftheyariselater.

• LeaveanRS232connectioneasilyaccessibleforusingtheCongurationUtility.

 TheB-500-MTRX-230-4x4isequippedwithmanysetupfunctionsthatmustbeaccessedbyusingaPCandthe

CongurationUtility.LeaveanRS232cableconnectedduringsetupandtestingthatcanbeconnectedtothePC

withease.IfthematrixisbeingcontrolledbyRS232,disconnectthecontrolsystemwhileusingtheUtility.

• Donotfullysecurewiringandequipmentuntilsetupandtestinghasbeensuccessfullycompleted.

 Waituntilallprogramming,sources,andzoneshavebeensetupandthoroughlytestedtostrapwiringandequipment

down,inordertoavoidrestrictingaccesstoconnectionsandsettingsontheequipment.

• Completeinitialsetupwithallsourcesconnectedtothematrixlocally.

 IfasourcewillbeconnectedtoaninputbyanHDMIextender,completeinitialsetupbyconnectingdirectlytothe

inputwithashortHDMIcable.Relocatethesourceandinstalltheextenderafterthesourcehasbeensetupand

tested,andthenconrmthenewarrangementworks.

Binarymatrixswitchersaredesignedtodeliverunsurpassedtechnologywithsuperiorperformance.However,where

youinstalltheswitchercanhavealargeaffectontheperformancethatyoureceive,andthelifeoftheunit.Hereare

someguidelinestofollowwheninstallingaB-500-MTRX-230-4x4Switcher.

• Besurethattheunitisinawell-ventilatedareathatprovidesadequatecooling.

• Donotblockthecoolingventslocatedonbothsidesoftheunit.

• Donotplacetheunitoncarpetingoranysimilarmaterial.

• Donotinstalltheunitnearasourceofheat,orinanextremelyhumidorwetlocation.

• Ifyourinstallationlacksgoodairow(suchassolidcabinetdoorsorwall-mountedracks),itmaybenecessaryto

createventilationtoallowoutsideairintothespace.

• Allowaminimumof3”offreeairspaceoneithersideoftheunit.(Doesnotapplytorackmounting)

• Allowaminimumof2”ofdepthbehindunittoaccommodatecablesandconnectors.

• Whenplacingonacabinetshelf,positiontheunitwithallfeetrestingonasolidlevelsurface.

7.4.1. Rack Installation

TheB-500-MTRX-230-4x4canbemountedinarackwiththefrontorrearpanelfacingoutward,andwilldisplace1Uof

verticalspacewheninstalled.Rear-facinginstallationallowsforeasyaccesstotheconnectionsforinstallationsthatdo

notrequirethefrontpaneloftheunittobeaccessed.Front-facingmountingisusefulforapplicationswherethefront

panelmustbeaccessibleorvisible.

Therackearsarepackagedseparatelyfromthematrixswitcherinthebox.Attachtheearstothesidesofthematrixat

thefrontorbackusingtheincludedscrews.Tightenthemwitha#2PhillipsScrewdriver.Itmaybenecessarytoremove

thefeetfromthebottomwhenrackmountingthematrixswitcher.Removethescrewsforthefeetwitha#2Phillips

Screwdriver,andstorethefeetandscrewstogetherincasetheyareneededinthefuture.

Note: The rack ears and mounting holes are only designed to safely hold the weight of the B-500-MTRX-230-4x4.

Do not use the matrix switcher as a shelf for other equipment in the rack.

B-500-MTRX-230-4x4 Installation Manual

Pg. 9

www.snapav.com Support: 866.838.5052

7.5. HDMI Input Connections

7.6. Output Connections

EachofthefourinputsontheB-500-MTRX-230-4X4utilizesastandardHDMIportforconnection.Followtheseguidelines

when connecting sources to the inputs.

• Alwaysusetheshortestcablepossiblebetweensourceequipmentandthematrixswitcherinputs.Usehighspeed

ratedcablestoguaranteethebestpossibleperformance.

• AvoidusingHDMIcableadaptersinruns.Alwaysrunoneunbrokencablewhenpossible.

TheB-500-MTRX-230-4X4matrixswitcherisequippedwithoneHDMIandoneHDBaseToutputportforeachofthe4

outputzones.Seethesectionsbelowforspecicinstructionsanddetailsforeachconnectiontype.

Note: Any input selected on an output zone is played on both the HDMI and HDBaseT outputs for that zone simultaneously.

This can be used to feed the same source to two devices. Read more about this feature below.

7.6.1. Choosing the Correct Output

OutputstodisplayscanbeconnectedusinganHDMIcableoraCat5e/6cableandHDBaseTReceiver(withashort

HDMIcableconnectingtheReceivertothedisplay).Foranyrunoverabout50feet,orforanyoutputthatwillutilizeIR

pass-through,useHDBaseT.

ForshortrunswhereHDMIcablescanberoutedtothedisplayand/ornoIRpass-throughisneeded,orifthereisHDMI

equipmentconnectedbetweenthematrixoutputandthedisplay(likeanAVreceiver),itmaybebesttousetheHDMI

outputtoconnectequipment.

Insomesituationsitmaybebenecialtousebothoutputs.Iftwodisplaysneedtobefedthesamesourceatalltimes,

onedisplaycanbefedfromtheHDBaseToutput,andonefromtheHDMIoutput.InjobswithanAVreceiverfeeding

surroundsoundtoazone,theaudiocanbefedtothereceiverviaHDMI,andanHDBaseTreceivercanbeusedtoroute

videotothedisplay.ThisisbenecialwithAVreceiversthathaveolderorlessreliableHDMIscalingorpass-through.

7.6.2. HDMI Outputs

TouseanHDMIoutputtofeedadisplay,connectbetweentheoutputofthematrixswitcherandtheinputofthedisplay.

FollowtheguidelinesbelowwhenusingHDMIoutputsforthebestperformanceandreliability.

• Alwaysusetheshortestcablepossiblebetweenequipment.Usehighspeedratedcablestoguaranteethebest

possibleperformance.

• AvoidusingHDMIcableadaptersinruns.AlwaysrunoneunbrokenHDMIcable.

• WhenroutingHDMItoanAVreceiverforsurroundsound,thenoutofthereceivertoadisplay,makesuretosetthe

AVreceivertoanHDMImodewherethesignalwillnotbeprocessedorscaledtoadifferentformat.Thiswillavoid

signaltimingissuesthatcancauseintermittentsyncortotallossofsync.Contactthedevicemanufacturerfordetails

regarding HDMI setup.

B-500-MTRX-230-4x4 Installation Manual

Pg. 10

™

7.6.3. HDBaseT Outputs

FollowtheseguidelineswhenselectingandinstallingtheHDBaseTcable,andthenfollowtheinstructionsafterwardto

completetheconnectionsforanoutput.

7.6.3.1. HDBaseT Wiring Recommendations

Cable Type- Shielded or Unshielded Cat5e/6

• CableDistanceLimitations:

Cat5e/ Cat6: Upto200ft

Cat6a: Upto230ft

• UseatleastCategory5ehigh-qualitytwistedpairsolidconductorcableratedtonolessthan350Mhzbandwidth.

Thehigherthecablestandard,thebetteritwillperform.

• Forthe bestresults installashieldedcable.Thiswill preventsignal dropoutandartifactsfrom beingcaused by

electromagneticandradiointerference(EMI/RFI)fromceilingfans,appliancesandelectricmotors.

• Usenomorethantwo5meterorshorter,solidorstranded,568Bterminatedpatchcablesintherun.Useshielded

patchcablesiftherunisshieldedtomaintainshieldcontinuity.

• Usenomorethantwokeystonesorcouplersintherun.Useshieldedkeystonesorcouplerswithshieldedcable

tomaintaincontinuity.

• Cleanlyterminateallcableendsandtesteverycableusedbeforeconnectingtheextendertoavoidtroubleshooting

terminationproblemslater.

• MarkeachendoftheHDBaseTcablewiththeincludedlabelstoavoidconfusionlater.

Connector Type- RJ45

• UseahighqualityRJ45connectorthatmatchesorexceedsthestandardofthecableinuse.Shieldedconnectors

mustbeusedwithshieldedcables,andmustmaintaincontinuityoftheshieldtobothconnectorstoprotectfrom

interference.

• Wehighlydiscouragetheuseof“EZ”style,openendRJ45swithHDMIextenders.

• AlwaysterminateRJ45connectorsintheHDBaseTsignalpathtothe568Bterminationstandardasrequiredby

HDBaseT standards.

7.6.3.2. Installation Instructions

1. InstalltheCat5e/6cableandterminatetheends.Thentestthecabletoensureoperation.

2. ConnecttheHDBaseTcabletothedesiredHDBaseToutputofthematrixswitcher.

3. ConnecttheHDBaseTcabletotheB-500-RX-230-IRReceiverortheHDBaseTdeviceinuse.

4. ConnectanHDMIcable(2metersorshorterisrecommended)betweentheHDMIOUTportontheReceiverand

thedesiredHDMIinputontheDisplay.

5. AttachthepowersupplytotheReceiverandpowertheunit.

6. Installationiscomplete.Testallconnectedinputsandoutputstogethertoensurereliableoperation.

7. ForIRPass-ThroughIntegration,seesection7.8.IRPass-ThroughInstallationandSetup,page12.

Pin 1 White/Orange Pin 5 White/Blue

Pin 2 Orange Pin 6 Green

Pin 3 White/Green Pin 7 White/Brown

Pin 4 Blue Pin 8 Brown

TIA/EIA Standard 568-B (Gold Pins Facing Up)

B-500-MTRX-230-4x4 Installation Manual

Pg. 11

www.snapav.com Support: 866.838.5052

LINK LINK

PWR

LINK LINK LINK LINK LINK LINK

Engineered in the USA

Manufactured in Taiwan

IR IN

ALL IR OUT

Matrix IR

Control Input

7.7. Matrix Control Connections

Alldrivers,associatedsoftwareandextradocumentationisavailableontheB-500-MTRX-230-4X4productpageat

www.SnapAV.comundertheSupportTab.

7.7.1. IR Control

The B-500-MTRX-230-4X4 can be controlled by IR from the front panel receiver or by

attaching a mono cable from the control system asher output to the “System IR In” port

onthebackofthematrixswitcher.Forthemostreliablecontrol,usetheSystemIRInport.

The matrix switcher will also process commands received on IR Receiver inputs from

B-500-RX-230-IRinzonesconnectedviaHDBaseT.(SeeSection7.10.2.IRPass-ThroughfromRoomstoSourceson

page15foranapplicationexampleofthisfeature.)

Note: System IR Control and the front panel IR Receiver can be disabled when not in use by using the Conguration

Utility. See the Conguration Utility manual section, “Other Settings” for more information.

7.7.2. RS232 Control

TocontroltheB-500-MTRX-230-4x4withRS232,thedevicesmustconnectusingthecorrectpincongurationforthe

controlsysteminuse.

Thematrixswitcherreceivescontroldataonpin2(RxD–DataReceive)andtransmitscontroldataonpin3(TxD-Data

Transmit).TheconnectioncablebetweenthematrixswitcherandtheAutomationSystemwillneedtobecongured

sothatpin2(RxD)ontheswitcherisconnectedtothecontrolsystemTxD(DataTransmit)pin,andpin3(TxD)onthe

switcherisconnectedtothecontrolsystemRxD(DataReceive)pin.Seethediagrambelowfordetails.

Congurationforcontrolsystemserialportscanvary.Refertothedocumentationforthesysteminusetoensureproper

connectionandconguration.

Note: This port is also used to communicate with a PC when using the PC Conguration Utility. Refer to the Conguration

Utility manual for details.

B-500-MTRX-230-4x4RS232PortConguration

LINK LINK

PWR

LINK LINK LINK LINK LINK LINK

Engineered in the USA

Manufactured in Taiwan

IR IN

ALL IR OUT

DB9 Female Connector

RxD (Data Receive)

TxD (Data Transmit)

GND

Pin Function

2 RxD(DataReceive)

3 TxD(DataTransmit)

5 Ground/Common

B-500-MTRX-230-4x4 Installation Manual

Pg. 12

™

7.8. IR Pass-Through Installation and Setup

ToutilizeIRpass-throughbetweenadisplaylocationandthematrixswitcher,installaB-500-RX-230-IRatthedisplay

anduseHDBaseTforroutingthesignal.Thematrixswitcherandthematrixreceiverareequippedwithportstoallow

commandstobesenttothedisplayorfromthedisplayarea.ThissectiondetailsthepinoutsandcorrectuseoftheIR

pass-through ports.

7.8.1. Matrix Switcher IR Connections

Theportsindicatedinthediagramaredescribedindetailbelow.Guidesforstandardapplicationsareincludedonthe

followingpagesforreferenceduringsetup.

7.8.2.MatrixSwitcherIRPortConguration

AllIRconnectionportsontheB-500-MTRX-230-4X4are3.5mmmonominiandusethispinoutconguration.Consult

withthemanufacturerofanyattachedIRequipmenttoconrmtheirpinoutmatchesbeforeuse.

IR Signal (Tip)

GND (Sleeve)

IR Signal Tip

GND (Ground) Ring

1. IR Output to Source 1 through 4

TheIRoutputfromeachconnectedB-500-RX-230-IRistransmittedtotheIROUTPUTTOSOURCEports.

Commandscanberoutedtothesourceselectedortothelike-numberedport.

2. IR Input to Room 1 through 4

 Use3.5mmmini-monocablestoconnectIRasheroutputsonacontrolsystemtotheseportstosendcommands

todisplaysorequipmentlocatedattheB-500-RX-230-IRmatrixreceiverlocation.Thenumbercorrespondstothe

outputzonenumber,soIRInputtoRoomport1willsendsignalstoHDBaseToutput1.

3. System All IR Out

 ThisportrepeatsanycommandsentfromtheIRReceiverportsonB-500-RX-230-IRMatrixReceiversconnected

to any HDBaseT output.

4. System IR In

 3.5mmmonominiIRinputportformatrixswitchIRcontrol.

LINK LINK LINK LINK

1 3

2 4

1 3

2 4

1 2 3 4

B-500-MTRX-230-4x4 Installation Manual

Pg. 13

www.snapav.com Support: 866.838.5052

7.9. B-500-RX-230-IR IR Connections

TheB-500-RX-230-IRIRportsaredescribedbelow.Usethediagramforreference.

7.9.1. IR Receiver

AttachanIRreceivertothisporttocaptureIRcommandsintheroomforpass-throughforsources.Thisportwillalso

sendcommandsbacktothematrixswitcherforcontrolofsourceselectionineachzone.

7.9.2. IR Flasher

AttachanIRashertothisportforcontrollingadisplayorotherequipmentwithcommandssentfromacontrolsystem

asheroutput,intothematrixswitcherIRINPUTTOROOMportsandthentothisport.

1 2

IR Signal (Tip)

GND (Ring)

12V DC (Sleeve)

IR Signal Tip

GND (Ground) Ring

+12V DC Sleeve

IR Signal (Tip)

GND (Sleeve)

IR Signal Tip

GND (Ground) Ring

7.9.3. Yellow Tag IR Adapter

Theyellowtaggedadapter(illustratedbelow)includedwiththeB-500-RX-230-IRisusedwhenplugginga3.5mm

monominicableintotheIRReceiverportoftheB-500-RX-230-IR.ThisisusedtosendIRcommandstothematrix

switcherlocationfromotherdevices,insteadofanIRReceiverthatusesa3.5mmmonominiportforoutput.

IR Signal (Tip)

GND (Ring)

12V DC (Sleeve)

IR Signal (Tip)

GND (Sleeve)

To IR Control System

Connecting Block

To B-500-MTRX

B-500-MTRX-230-4x4 Installation Manual

Pg. 14

™

7.10. IR Application Diagrams

7.10.1. IR Pass-Through from Control System

ThediagramaboveillustratesatypicalinstallationwithaB-500-MTRX-230-4X4wherealloftheequipmentisbeing

controlledbyacontrolsystemthatusesRF(RadioFrequency)remotesineachoutputzone.

• TheRFremotestransmitcommandsbacktothecontrolsystemwhichthensendscommandstoeachdevicebeing

controlled. Custom programming by the installer sets the control system up to automatically switch inputs and

outputsinthematrixswitcherasneeded,sotheenduseronlyhastoselectthesourcetheywanttowatch.

• Eachdisplay(onlyoneispicturedforreference)requiringIRcontrolisconnectedtothesystemviatheHDBaseT

output ofthe matrix switcher. Cat5e/6 cableconnects to a B-500-RX-230-IR Receiver, which is attached tothe

displayviaHDMIforsignal.AnIRasherconnectedtotheIRasherportsendstheIRcommandstothedisplay.

Sourcesaredirectlycontrolledbythecontrolsystem.

• IR control for displays is routed from the control system to the matrix switcher using 3.5mm mono mini cables

pluggedintoIRINPUTTOROOMports.ThecommandspassfromamatrixswitcherporttotheHDBaseToutputof

thesamenumber.Inthediagramthemonocableusedtosendcommandstotheoutput4zoneispluggedintoIR

INPUTTOROOMport4.Thisallowsdiscretecontrolofeachdisplayconnected,eveniftheyaremodelswiththe

samecodes.

• SomedisplaysandprojectorscanbecontrolledbyothermethodsthanIR.TheprojectorpicturedfeaturesIPcontrol,

soitisreceivingcommandsfromthecontrolsystemoveranEthernetconnection.AnHDMIcableisconnectingitto

thematrixswitcheroutputsinceitisinstalledcloseenoughtotheequipmentandrequiresnoIRasher.

• Whenthesystemisinuse,iftwooutputsareconnectedtothesameinput,thesourcewillchangeonbothoutputs

withanycommandsentsinceitcan’tsendtwoHDMIstreamsatonce.Thismustbeconsideredwhendecidingon

thesourcestoconnectfordistribution.

Example: In a home with four displays connected, if users in every room want to watch satellite on different

channels, there must be four satellite receivers set up as sources. With custom programming, each output

can be programmed to use only one of the satellite source inputs, giving each output a dedicated cable box,

while allowing other less-used sources to connect to any output.

LINK LINK LINK LINK

1 3

2 4

1 3

2 4

24V DC 2.7A

IR Outputs

RS232

IR Inputs

B-500-RX-230-IR

Projector

HDMI

Cat5e/6

HDMI

PLAY

HDMI Source HDMI Source

HDTV

IR Flasher

Ethernet Connection

RS232

IR Flasher

3.5mm Mono

C5e/6

Ethernet

Connection

Cat5e/6

B-500-MTRX-230-4x4 Installation Manual

Pg. 15

www.snapav.com Support: 866.838.5052

7.10.2. IR Pass-Through from Rooms to Sources

ThediagramaboveillustratesatypicalinstallationwithaB-500-MTRX-230-4X4wherealloftheequipmentisbeing

controlledbyIRremotesineachoutputzone.

• In each room with a connected display, an entry-level universal IR remote is being used to control the display

andsourcesinuse.CustomprogrammingsetupineachremotebytheinstallersendsIRcommandsoutofthe

remotemeantforthedisplaydeviceintheroom,thesources,andthematrixswitchersimultaneously.Thematrix

commandsareprogrammedtobesentautomaticallyasneededsotheenduseronlyhastoselectthesourcethey

want to watch.

• To make this system work seamlessly, two advanced IR options have been enabled in the matrix switcher

CongurationUtility“OtherSettings”menu:IRSourceRoutingandIRMatrixControlfromroom.

 o IR Source Routing allows the commands from the room to be routed directly to the source selected to be

displayedintheroom.ThissimpliesIRroutingbecauseonlyoneasherhastoconnecttothesource.

 o IRMatrixControlsetsthematrixswitchersothatanycommandsentfromanyHDBaseToutputtocontrolthe

matrixisautomaticallyreceivedinternally,eliminatingtheneedforanexternalconnectionbacktothematrix

forcontrol.SeeSection9.AdvancedSetupUsingtheCongurationUtilityonpage20formoreinformationon

changing these settings.

• Whenthecommandsaresent,thedisplaydeviceiscontrolleddirectlybytheremote.Thecommandsforthematrix

switcherandsources are pickedupbytheIR receiverconnected totheB-500-RX-230-IRand sent backtothe

correctIROUTPUTTOSOURCEportandtothematrix.

• Whenthesystemisinuse,iftwooutputsareconnectedtothesameinput,thesourcewillchangeonbothoutputs

withanycommandsentsinceitcan’tsendtwoHDMIstreamsatonce.Thismustbeconsideredwhendecidingon

thesourcestoconnectfordistribution.

Example: In a home with four displays connected, if users in every room want to watch satellite on different

channels, there must be four satellite receivers set up as sources. With custom programming, each output

can be programmed to use only one of the satellite source inputs, giving each output a dedicated cable box

while allowing other less-used sources to connect to any output.

LINK LINK LINK LINK

1 3

2 4

1 3

2 4

24V DC 2.7A

Projector

PLAY

HDMI Source HDMI Source

HDTV

IR Receiver

B-500-RX-230-IR

IR Receiver

HDMI

IR Flasher IR Flasher

HDMI

B-500-RX-230-IR

HDMI

Cat5e/6Cat5e/6

B-500-MTRX-230-4x4 Installation Manual

Pg. 16

™

8. EDIDConguration

8.1. Source Setup

8.2. Display Setup

8.3.AutoEDIDConguration

The displaysused within an installation usually varyfrom room to room,and some may not supportall resolutions

availablefromasource.Itisnecessarytomakesuresourceswillprovideavideoandaudioformatcompatiblewith

allconnecteddisplaysprogrammedtousethem.Toaccomplishthis,theB-500-MTRX-230-4X4includesbuilt-inEDID

managementforeachsourceinput.ThestoredEDIDispersource,soalldisplaylocationswillseethesameresolution

andhavethesameaudioformatwhenthatsourceisselected.

Note: Source is only able to output one video resolution and one audio format.

Note: The default EDID for each input is always 1080p with 2 channel stereo audio, since this format is accepted by

most displays with no issues.

ThefollowingsectionsexplainconguringEDIDsviatheincludedIRRemote.BeforeconguringtheEDID,besureto

refertothesourceanddisplaymanualsforavailablefeaturesandresolutionsforeachdevice.Formoreinformation

aboutusingtheincludedremote,seeSection11.1IRRemoteonpage21.

While all EDID congurations are available via the remote, the Conguration Utility can be used for faster setup.

DownloadtheCongurationUtilityandmanualontheSupportTabfortheB-500-MTRX-230-4X4atwww.SnapAV.com.

What is EDID? EDID, or Extended Display Identication Data, is a stream of information sent from a display to a source

when the two devices are connected to tell the source what video and audio formats the display can use. This prevents

sources from outputting media that won’t work with the display.

Checkeachsourceandconrmthattheaudioformatandvideoresolutionaresetsothattheywillchangebasedonthe

EDID.Normallythissettingiscalled“Auto”orsimilar.

Note: EDID setup is not required if the source supports setting one xed video resolution and audio format.

ItisrecommendedthatConsumerElectronicsControl(CEC)beturnedOFFinalldisplayswhenusingtheB-500-MTRX-

230-4X4.Thiswillprovideforpropercommunicationofvideo/audiosignalsandallowEDIDstofunctionattheiroptimum

performance.Refertothedisplay’smanualforinformationonhowtoturnthisfunctionOFF.

ThequickestandeasiestmethodforcongurationistouseAutoEDID.Whenthismodeisusedthematrixswitcher

looksattheEDIDfromeachoftheconnecteddisplays.Itusesthehighestcommonvideoresolutiontocreateanew

EDIDandsavesthatEDIDinalloftheinputs.

Note: Auto EDID sets audio to 2ch stereo for all inputs regardless of the capability of the connected displays. If multi-

channel audio is desired, embedded EDIDs or Learned EDIDs will need to be used.

When to use Auto EDID

• Allsourceswillbeavailableonalldisplays.

• Asarststeptoconguration,followingupwithadvancedmethodsforparticulardisplaysanddedicatedsources.

Note: For advanced EDID conguration when using a legacy display and/or dedicated sources, use embedded EDIDs

or learning as described in the following sections.

Sets EDID Based on All Connected Displays Display Readout (Example)

1.PressDEFAULT

E-

2.PressNumberKey9

3.PressENTER

8.3.1.HowtoCongureAutoEDID

TosetupAutoEDIDconguration,rstmakesurethatalldisplaysarepoweredonandconnectedtothematrixswitcher.

Then,pressthefollowingremotebuttonsinthisorder.Besuretopresseachbuttonwithin10secondsoftheprevious

button-presstopreventthecommandfromresetting.

B-500-MTRX-230-4x4 Installation Manual

Pg. 17

www.snapav.com Support: 866.838.5052

8.4.EmbeddedEDIDConguration

Inadditiontotheautomaticcongurationmethod,EDIDsintheB-500-MTRX-230-4X4canbesettoinputsmanuallyby

selectinganEDIDfromtheembeddedlist(defaultEDIDsprogrammedintothematrixswitcher).

Thematrixswitchercontainseight‘embedded’EDIDsthatmaybeassignedtoinputs.TheseEDIDsdenegroupsof

videoandaudiocapabilitiesthatareusefulforconguringsourcesinmostsystems.

8.4.1. Embedded EDID Chart

Explanation of Embedded EDIDs

Video ResolutionintheEmbeddedEDIDsisthehighestresolutionaconnectedsourcewilloutput.Thatis,ifthesource

iscapableof1080P@60itwillberequiredbyEDIDs1-6toprovidethatresolution.However,ifthesourceisonlycapable

of1080iitwilloutput1080i,etc.Itisassumedthatanydisplaythatcanacceptthespeciedvideoresolutioncanalso

acceptallstandardvideoresolutionslessthanthatspecied.

Color Depthisthemaximumnumberofbitsusedtoencodecolor.24bitcolordepthis8bitspercolor(red,blue,green).

36bitcolordepthis12bitspercolor(red,blue,green).

3Dindicatesthatthesourcecanoutput3Difitisavailableinthecontent.

Audio Format indicatesthemaximumnumberofaudiochannels,aswellastheaudioformatthatthesourceisallowed

tooutput.ForanEmbeddedEDIDwith7.1chAudioFormat,thesourcedevicewilloutputthehighestaudiopossible

basedonthecontent.Forexample,if7.1chisnotavailableand5.1chisavailable,thentheoutputwillbe5.1ch.The

sameistrueif2chstereoistheonlyaudioavailablefromthesource.EmbeddedEDIDswith2chstereowilllimitoutput

tothataudioformatregardlessofwhatisavailableinthecontent.

Embedded EDIDs 7 and 8areprovidedforlegacydisplaysthatcanonlyacceptresolutionsuptoamaximumof1080i/

720p.The1080iislistedrstsincealmostallolderHDdisplayscanaccept1080ibutnotallcanaccept720p.Forthese

twoEmbeddedEDIDs,(7&8)thesourcewilloutput1080i.Should1080inotbeavailable,thesourcewilloutput720p.

Note: There is a possibility that 720p may not work for a very small number of older displays that may still be in use. It

will be necessary to use a Learned EDID from the display to store in the Input EDID of any sources that will be

routed to that display if 720p is not supported. See Section 8.5. EDID Learning on page 18 for directions to set a

learned EDID.

When to Use Embedded EDIDs

• Formostcurrentdisplaysandsources,usingembeddedEDID#2isrecommendedunlessmultichannelaudiois

needed.Inthatcase,useembedded#3.TheotherembeddedEDIDsareusefulforsupportinglegacyequipment.

Embedded EDID Resolution Color Depth Audio

1 1080p@60Hz 24-Bit 7.1ch

2(FactoryDefault) 1080p@60Hz 24-Bit 2ch

3 1080p@60Hz 24-Bit 3D 7.1ch

4 1080p@60Hz 24-Bit 3D 2ch

5 1080i@60Hz 36-Bit 3D 7.1ch

6 1080i@60Hz 36-Bit 3D 2ch

7 1080i@30Hz/720p@60Hz 24-Bit 7.1ch

8 1080i@30Hz/720p@60Hz 24-Bit 2ch

B-500-MTRX-230-4x4 Installation Manual

Pg. 18

™

8.4.2. How to Set Embedded EDID for a Single Input

8.5.1. How to Learn EDID to a Single Input

8.4.3. How to Set Embedded EDID for All Inputs

Example: Input =1 Embedded EDID=4 Display Readout (Example)

1. PressDEFAULT

E-

2. PressNumberKey(1-8)toselectoneEmbeddedEDID

3.PressINPUT

4. PressNumberKey(1-4)toselecttheInputtowhichtheEDID

isapplied

5. PressENTER

(success)

(fail)

Example: Input =1 Embedded EDID=4 Display Readout (Example)

1. PressDEFAULT

E-

2. PressALLtoselectallInputs

A-

3.PressNumberKey(1-8)toselectEmbeddedEDID

4. PressENTER

(success)

(fail)

8.5. EDID Learning

FormoreadvancedEDIDconguration,learningcanbeusedtoassignEDIDsdirectlyfromdisplaystooneormore

inputs.Thisisusefulwhenthesystemcontainsadisplaythatcannotacceptthehighestresolutionavailablefrom

sources,butallsourcesneedtobeavailabletoalldisplays.

Note: EDIDs can be learned from displays connected via the HDBaseT or the HDMI output.

When to Use Learned EDIDs

• AnolderdisplaydoesnotworkproperlywithanyoftheembeddedEDIDs.

• WhenthesourceisaPCitmaybenecessarytousealearnedEDID.

• LearningEDIDtoasingleinput

Example: Input =1 EDID Learned from Output 4 Display Readout (Example)

1. PressLEARNonceforHDMIportortwiceforHDBaseTport

L.-.

2.PressOUTPUT

3.PressNumberkey(1-4)toselecttheOutputtheEDIDis

learnedfrom

4.PressINPUT

L-

5.PressNumberKey(1-4)toselecttheInputtowhichtheEDID

isapplied

6.PressENTER

(success)

(fail)

B-500-MTRX-230-4x4 Installation Manual

Pg. 19

www.snapav.com Support: 866.838.5052

8.5.2. How to Learn EDID to All Inputs

Example: Input=All EDID Learned from Output 4 Display Readout (Example)

1.PressLEARN

L.-.

2.PressOUTPUT

L-

3.PressNumberKey(1-4)toselecttheOutputtheEDID

islearnedfrom

4.PressENTER

(success)

(fail)

8.6. Viewing Input EDID Status

IfthereisaquestionabouttheEDIDsetforaninput,thestatusofthatinput’sEDIDcanbereviewedusingthe

includedIRremoteandwatchingthematrixswitcherfrontpaneldisplay.

Notes about EDID Status

• IftheEDIDwaslearnedfromanoutput,theexactEDIDspecicationswillnotbeshown,buttheoutputnumberwill

beidentied.Reviewthespecicationsofthedisplayattachedtotheoutputtodetermineitscompatibleresolutions.

• If the second digit (the Input being queried) has a dot after it, then the rst digit is the EDID number from the

EmbeddedEDIDtable.

• Iftheseconddigit(theInputbeingqueried)doesnothaveadotafterit,therstdigitistheOutputtheEDIDwas

learnedfrom(step4fromexampleabove).

Example: View the EDID for Input 3.

DisplayReadout(Example)

EDID5Assigned

fromEmbedded

EDIDTable

EDIDLearned

fromOutput4

1.PressSTATUS

-- --

2.PressINPUT

-- --

3. PressNumberKey(1-8)toselectthedesiredInput

-3 -3

4.PressENTER

5.3. 4.3

B-500-MTRX-230-4x4 Installation Manual

Pg. 20

™

9. AdvancedSetupUsingtheCongurationUtility

10. Firmware Update

There are several setup options available that can only be modied using the matrix switcher Conguration Utility.

Theseitemsaredefaultedtothemostcommonsettingsthatshouldworkinmostinstallations.

TheCongurationUtilityandmanualareavailablefordownloadontheSupportTaboftheB-500-MTRX-230-4X4product

pageatwww.SnapAV.com.DownloadandruntheUtilitytogainaccesstothesesettingsbyconnectingtothematrixand

clicking“OtherSettings.”

BinarymayoccasionallyreleasenewrmwarefortheB-500-MTRX-230-4X4toaddressnewstandardsandtechnology.

Itwillneverbenecessarytoperformanupdatetoanexisting,correctlyfunctioningsystem,butduringinstallationor

serviceitisrecommendedtochecktheinstalledversiontobesureitisthenewestavailable.

Forfullupdateinstructions,seethesectiontitled,“FirmwareUpdate”intheCongurationUtilitymanual.Newrmware,

the Conguration Utility, and the Conguration Utility manual are available for download on the Support Tab of the

B-500-MTRX-230-4X4productpageatwww.SnapAV.com.

9.1. IR Source Routing

9.2. IR Front Panel IR Enable

9.4. Front Panel Power Button Active

9.3. Matrix Control from Room Enable

TheIRSourceRoutingfeatureallowsdiscretecontrolofthesourceselectedfromanyconnectedHDBaseToutputusing

anIRreceiverpluggedintotheB-500-RX-230-IR.Thissettingisonlyrelevantwhenusingin-roomIRremotestocontrol

sourcesconnectedtothematrixswitcher.WhensettoYes,thematrixwillroutecommandsfromtheHDBaseTReceiver

totheIROutputtoSourceportthatmatchesthesourceinputnumbercurrentlyselectedonthatoutput.

WhensettoNo,commandswillbesentonlyoutoftheIROutputtoSourceportthatmatchestheHDBaseTReceiver

numberfromwhichitoriginated.

ThissettingcontrolstheoperationofthefrontpanelIRreceiverbuiltintotheB-500-MTRX-230-4X4.Thisshouldbe

disabledifusingtheSYSTEMIRINporttocontrolthematrixswitcherviaIR,orifthematrixswitcherismissingor

receivingextracommandsduringuse(strayIRinterferingwiththeport).

TheFrontPanelPowerButtoncanbedisabledifdesired.Disablethebuttonwhenthematrixswitcherisprogrammedto

beonatalltimesorinjobswhereturningoffthematrixfromtheswitchercancauseissueswithcontrol.

TheMatrixControlfromRoomEnableoptionallowsMatrixControlIRcommandstobesentfromtheroomasifasource

werebeingcontrolled.Turnthisoptionoffifthematrixswitcherisbeingcontrolledbyanyothermethodthanin-roomIR.

Note: To use Matrix Control from Room, it is recommended to program a universal remote control with discrete commands

for matrix control to keep in each zone, rather than using the included IR remote or commands learned from it.

Go to the Support Tab of the B-500-MTRX-230-4X4 product page at www.SnapAV.com to see and download the

available IR codes and drivers for IR remote programming.

Default Setting: Yes

Page is loading ...

Binary B-500-MTRX-230-8x8 Installation guide

Brand: Binary

Model: B-500-MTRX-230-8x8

Category: Supplementary music equipment

Type: Installation guide

This manual is also suitable for

Download PDF

report

Binary B-500-MTRX-230-8x8 Installation guide

This manual is also suitable for

Binary B-500-MTRX-230-8x8 Installation guide

Related papers

Other documents