Binary B-500-MTRX-230-16x16 Installation guide

Category
Supplementary music equipment
Type
Installation guide

This manual is also suitable for

B-500-MTRX-230-4x4
Binary™ HDMI Matrix Switcher
with HDMI and HDBaseT Outputs
Installation Manual
B-500-MTRX-230-4x4 Installation Manual
Pg. 2
© 2013 Binary
1. Important Safety Instructions
Toreducetheriskofreorelectricshock,donotexposethisapparatustorainormoisture.Donot
removecover.Nouserserviceablepartsinside.Referservicingtoqualiedservicepersonnel.
Thelightningashwitharrowheadsymbol,withinanequilateral
triangle, is intended to alert the user to the presence of
un-insulateddangerousvoltagewithintheproduct’senclosure
thatmaybeofsufcientmagnitudetoconstituteariskofelectric
shock to persons.
Theexclamationpointwithinanequivalenttriangleisintended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanyingtheappliance.
1. Readandfollowallinstructionsandwarningsinthismanual.Keepforfuturereference.
2. Do not use this apparatus near water.
3. Cleanonlywithadrycloth.
4. Donotblockanyventilationopenings.Installaccordingtomanufacturer’sinstructions.
5. Donotinstallnearanyheatsourcessuchasradiators,heatregisters,stovesorotherapparatus(including
ampliers)thatproduceheat.
6. Donotoverridethesafetypurposeofthepolarizedorgrounding-typeplug.Apolarizedplughastwoblades-one
widerthantheother.Agroundingtypeplughastwobladesandathirdgroundingprong.Thewidebladeorthe
thirdprongisprovidedforyoursafety.Iftheprovidedplugdoesnottintoyouroutlet,consultanelectricianfor
replacementoftheobsoleteoutlet.
7. Protectthepowercordfrombeingwalkedonorpinchedparticularlyatplug,conveniencereceptacles,andthe
pointwhereitexitsfromtheapparatus.
8. Onlyuseattachments/accessoriesspeciedbythemanufacturer.
9. Referallservicingtoqualiedservicepersonnel.Servicingisrequiredwhentheapparatushasbeendamagedin
anyway,suchaswhenthepower-supplycordorplugisdamaged,liquidhasbeenspilledorobjectshavefallen
intotheapparatus,theapparatushasbeenexposedtorainormoisture,doesnotoperatenormally,orhasbeen
dropped.
10. DONOTEXPOSETHISEQUIPMENTTODRIPPINGORSPLASHINGANDENSURETHATNOOBJECTS
FILLEDWITHLIQUIDS,SUCHASVASES,AREPLACEDONTHEEQUIPMENT.
11. TOCOMPLETELYDISCONNECTTHISEQUIPMENTFROMTHEACMAINS,DISCONNECTTHEPOWER
SUPPLYCORDPLUGFROMTHEACRECEPTACLE.
12. THEMAINSPLUGOFTHEPOWERSUPPLYCORDSHALLREMAINREADILYOPERABLE.
Warning:
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRICAL SHOCK.
DO NOT REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
B-500-MTRX-230-4x4 Installation Manual
Pg. 3
www.snapav.com Support: 866.838.5052
1. Important Safety Instructions
2. Product Overview
3. Package Contents
4. Features
5. Recommended for Installation
6. Device Layout
6.1.FrontPanel
6.2.RearPanel
7. Installation Setup
7.1. BasicInstallationDiagram
7.2. Basic Instructions
7.3. InstallationTips
7.4. SwitcherLocationandPlacement
7.4.1. RackInstallation
7.5. HDMI Input Connections
7.6. Output Connections
7.6.1. Choosing the Correct Output
7.6.2. HDMI Outputs
7.6.3. HDBaseT Outputs
7.7.MatrixControlConnections
7.7.1. IRControl
7.7.2. RS232Control
7.8.IRPass-ThroughInstallationandSetup
7.8.1. MatrixSwitcherIRConnections
7.8.2. MatrixSwitcherIRPortConguration
7.9. B-500-RX-230-IRIRConnections
7.9.1. IRReceiver
7.9.2. IRFlasher
7.9.3. YellowTagIRAdapter
7.10.IRApplicationDiagrams
7.10.1.IRPass-ThroughfromControlSystem
7.10.2. IRPass-ThroughfromRoomstoSources
8. EDIDConguration
8.1. Source Setup
8.2.DisplaySetup
8.3. AutoEDIDConguration
8.3.1. HowtoCongureAutoEDID
8.4.EmbeddedEDIDConguration
8.4.1. EmbeddedEDIDChart
8.4.2. HowtoSetEmbeddedEDIDforaSingleInput
8.4.3. HowtoSetEmbeddedEDIDforAllInputs
8.5.EDIDLearning
8.5.1. HowtoLearnEDIDtoaSingleInput
8.5.2. HowtoLearnEDIDtoaAllInputs
8.6.ViewingInputEDIDStatus
9. AdvancedSetupUsingtheCongurationUtility
9.1.IRSourceRouting
9.2.IRFrontPanelIREnable
9.3.MatrixControlfromRoomEnable
9.4.FrontPanelPowerButtonActive
10. Firmware Update
11. Operation and Control
11.1.IRRemote
11.1.1.RouteInputstoOutputs
11.1.2.TurnOff(Mute)Outputs
11.1.3.DisplayOutputStatus
11.1.4.ResettingtoFactoryDefaults
12. Troubleshooting
12.1.GeneralTroubleshootingGuidelines
12.2.NoSignalfromSourcetoanyDisplay
12.3.NoSignalfromanySourcetoanDisplay
12.4.Audioissues
13. Contacting Tech Support
14. System Layout Chart
15. Specications
16. Warranty
Table of Contents
2
4
4
4
4
5
5
6
7
7
7
8
8
8
9
9
9
9
10
11
11
11
12
12
12
13
13
13
13
14
14
15
16
16
16
16
16
17
17
18
18
18
18
19
19
20
20
20
20
20
20
21
21
21
22
22
23
24
24
24
24
25
25
26
27
27
B-500-MTRX-230-4x4 Installation Manual
Pg. 4
© 2013 Binary
2. Product Overview
Welcome to Binary™, one of the most highly regarded brands available today. This product is engineered to
provide years of exceptional reliability. We appreciate your business and we stand committed to providing our
customerswiththehighestdegreeofqualityandserviceintheindustry.
TheB-500-MTRX-230-4x4isastate-of-the-artHDMImatrixswitcherwithbothHDMIandHDBaseTOutputs.Itprovides
truematrix routingforHDMIsignals.WithfeaturessuchasHDMI3Dsupport,sophisticatedEDIDhandling,IR,and
RS232,thisproductisidealforresidentialandcommercialmediadistributionsystems.TheHDBaseTconnectionon
eachoutputextendsHDMIsignalsandbi-directionalIRtoremoteroomsupto230feetawayviaCat5e/Cat6/Cat6a.
Note: This manual covers all aspects of installation and setup of the B-500-MTRX-230-4x4 for most applications. Some
features must be congured using the Conguration Utility software. Go to the product page for the B-500-MTRX-
230-4x4 at www.SnapAV.com and click on the Support Tab to download the Conguration Utility and manual.
4. Features
• (4)HDMIinputsby(4)mirroredHDMIandHDBaseToutputs
• Upto8displayscanbeattachedintotal(usingbothHDMIandHDBaseToutputs)
• SupportsVideoresolutionsupto1080p/6036bitcolor
• SupportsallHDMIaudioformatsincludingDolbyTrueHDandDTSMasterHD
• SupportsallHDMI3Dformats
• SophisticatedEDIDhandlingincludingEmbedded,Learned,andAutomodes
• HDMIorDVIwithadapter(notincluded)
• IRControlfromintegratedreceiveror3.5mminput
• Bi-directionalIRpass-throughwhenusingB-500-RX-230-IR
• HomeAutomationControlviaIR,andRS-232
• PCSetupandCongurationusingdedicatedsoftware
• HDCP2.0compliant
• CECPassThrough
5. Recommended for Installation
• PhillipsScrewdriver(forrackearattachment)
• Upto4sources
• Upto4displays(8ifusingbothHDBaseTandHDMIoutputs,seeSection7.6,Page9)
• BinaryHighSpeedHDMICablestoconnectsourcestoB-500-MTRX-230-4x4HDMIinputs
• BinaryHDMIcablesorB-500-RX-230-IRunitsandCat5e/6cableinstalledbetweenmatrixswitcherlocationand
displays(Seesection7.6.3.1,page10forHDBaseTwiringrecommendations)
• RJ45connectorsandterminationtools(IfusingB-500-RX-230-IR)
• ControlSystemtocontroloperationofB-500-MTRX-230-4x4
• WindowsPCwithCongurationUtilityinstalledandRS232adapter
• CongurationUtilityManual
3. Package Contents
• (1)B-500-MTRX-230-4x4
• (2)Rackearsformounting(screwsincluded)
• (1)IRRemoteControl
• (1)Powersupply24V2.7ADC
• (1)InstallationManual
• (1)CD-ROM
B-500-MTRX-230-4x4 Installation Manual
Pg. 5
www.snapav.com Support: 866.838.5052
6. Device Layout
6.1. Front Panel
1. Power On/Off Switch
TogglePowerfromOntoStand-by.CanbedisabledfromCongurationUtilitysoftware.
2. Source Status LEDs
IndicatesthattheselectedsourceisonandtransmittinganHDMIsignal.
3. Output Display
Displaysthelastoutputselected.
4. IR Receiver Window
IRreceiverforMatrixtocapturecommandssentbyIRremote.
5. Input Display
Displaysthelastinputselected.
1 2
3
54
B-500-MTRX-230-4x4 Installation Manual
Pg. 6
© 2013 Binary
6.2. Rear Panel
1. HDMI Inputs 1 through 4
ConnectHDMIcablesfromsourcestothematrixswitchfordistribution.
2. RS-232 control port (DB9)
AttachconnectionfromcontrolsystemorWindowsPCforserialcontroloftheB-500-MTRX-230-4X4.
3. IR Output to Source 1 through 4
3.5mmmonominiconnectionsusedtoconnectIRashersforcontrollingsources.Theseportsmaybeconguredto
routecommandsonlyfromtheIRoutputcorrespondingtotheHDBaseToutputnumber(IRzonerouting),ordirectly
tothesourceselectedforviewingonanHDBaseToutput(IRsourcerouting).(SeeCongurationUtility)
4. RJ45 HDBaseT Outputs 1 through 4
Connect568BterminatedCat5e/6HDBaseTcableroutedtoaB-500-RX-230-IRupto230feetawaytofeedHDMI
signaltodisplay.OutputsimultaneouslydisplaysthesamesourceastheHDMIoutputofthesamenumber.
5. Link LED
ThegreenLinkLEDsindicatethestatusoftheHDBaseTconnection.Off=Nolink;On=Linkisactive.
6. HDMI Outputs 1 through 4
ConnectHDMIcablestoroutetodisplays.OutputsimultaneouslydisplaysthesamesourceastheHDBaseToutput
ofthesamenumber.
7. IR Input to Room 1 through 4
3.5mmmono-miniconnectionforIRpass-through.ConnectthecontrolsystemIRFlasheroutputstosendcommands
todisplaysorotherdevicesintheroom(onlywhenusingtheB-500-RX-230-IRtoextendtodisplays).
8. System All IR Out
3.5mmmonominiport,repeatsallIRcommandsfromallconnectedHDBaseToutputs(fromIRReceiverportof
B-500-RX-230-IR).
9. System IR In
3.5mmmonominiIRinputportformatrixcontrol.
10. Latch-Locking Power Jack
24V2.7ADCpowersupplyportwithlockingscrewcollarforsecureconnection.
LINK LINK LINK LINK
1 3
2 4
1 3
2 4
24V DC 2.7A
2 3 4 7 8 1061 95
B-500-MTRX-230-4x4 Installation Manual
Pg. 7
www.snapav.com Support: 866.838.5052
7. Installation and Setup
7.1. Basic Installation Diagram
7.2. Basic Instructions
1. Unpackthematrixandinstallitnearthesourceequipment.(7.4.SwitcherLocationandPlacement,page8)
Note: Do not power the matrix switcher until it is indicated to do so.
2. InstallandconnecteachsourcetoaninputonthematrixswitcherusingtheshortestHDMIcablepossible.
(7.5.HDMIInputConnections,page9)
3. InstallthedisplaysandoutputwiringtothematrixlocationusingHDMIcablesforstandardHDMIoutputorCat5e/6
ifB-500-RX-230-IRReceiverswillbeused.(7.6.OutputConnections,page9)
4. RecordtheinputsandoutputsusedintheSystemLayoutChartforfuturereference.
(14.SystemLayoutChart,page26)
5. Ifusingacontrolsystem,connectittotheappropriateportonthematrixswitcherforthedrivertypebeingused:
IRorRS232control.(7.7.MatrixControlConnections,page11)
6. Installandcongurethedriverformatrixswitchingcontrolintothecontrolsystemprocessor.
(7.7.MatrixControlConnections,page11)
7. InstalltheIRequipmentandsetupIRpass-throughifusingit.
(7.8.IRPass-ThroughInstallationandSetup,page12)
8. Attachthepowersuppliestothematrix,sources,anddisplays,thenpowerupthesystem.
9. Testallinputandoutputselectionsforsync,reliableswitching,correctaudioformatandvideoresolution.Usethe
factoryremoteortheMatrixCongurationUtilitytosetupEDIDsasneeded.(8.EDIDConguration,page16)
10. ChangeanyadvancedsettingsintheMatrixCongurationUtilityasneededtosuittheinstallation.
(9.AdvancedSetupUsingtheCongurationUtility,page20)
Completethebasicinstallationsectiontosetupthematrixswitcherformediadistributionbeforecompletinganyother
setup.Usethisdiagramforreferenceduringbasicinstallationofthematrixswitcher,sources,displaysandwiring.
Thesearethebasicstepsthatmustbetakentoconnectequipmenttotheinputsandoutputsofthematrixswitcherand
congurethesystemforuse.Seethesectionslistedforfullinformationoncompletingeachstep.
LINK LINK LINK LINK
1 3
2 4
1 3
2 4
24V DC 2.7A
Projector
Game
Console
PC
HDTV HDTV HDTV
HDMI
HDMi
HDMI
HDMI
HDMI
HDMI
HDMI
B-500-RX-230-
IR
Cat5e/6
HDMI
Home Automation System
Blu-ray Player Cable/Sat Box
AC Power
AC Power
RS232
B-500-MTRX-230-4x4 Installation Manual
Pg. 8
© 2013 Binary
7.3. Installation Tips
7.4. Switcher Location and Placement
Followingthesetipsduringtheinstallationprocesswillhelpguaranteeasuccessfulinstallation.
• Testeverycablebeforeuse.
Alwaystestcablesbeforeuse.Field-terminatedcablesshouldbecheckedforcontinuityafterterminationtobesure
theconnectorswereinstalledcorrectly.
• Labeleachcableasitisinstalled.
Thiswillaidinconnectionsetupandprogramming,andwillalsomakeiteasiertocomebacktoajobatalaterdate
andimmediatelyknowwhatisconnectedwhere.
• CompletetheSystemLayoutChart(page26)inthebackofthemanualduringinstallation.
Recordthesourceconnectedtoeachinput,theoutputnumberofeachdisplay,andthemethodofroutingsignalin
thechartforreferenceduringinstallationandsetup.Useitafterwardtokeeptrackofequipmentinuse,openports
forexpansion,andtohelpidentifywheretotroubleshootissuesiftheyariselater.
• LeaveanRS232connectioneasilyaccessibleforusingtheCongurationUtility.
TheB-500-MTRX-230-4x4isequippedwithmanysetupfunctionsthatmustbeaccessedbyusingaPCandthe
CongurationUtility.LeaveanRS232cableconnectedduringsetupandtestingthatcanbeconnectedtothePC
withease.IfthematrixisbeingcontrolledbyRS232,disconnectthecontrolsystemwhileusingtheUtility.
• Donotfullysecurewiringandequipmentuntilsetupandtestinghasbeensuccessfullycompleted.
Waituntilallprogramming,sources,andzoneshavebeensetupandthoroughlytestedtostrapwiringandequipment
down,inordertoavoidrestrictingaccesstoconnectionsandsettingsontheequipment.
• Completeinitialsetupwithallsourcesconnectedtothematrixlocally.
IfasourcewillbeconnectedtoaninputbyanHDMIextender,completeinitialsetupbyconnectingdirectlytothe
inputwithashortHDMIcable.Relocatethesourceandinstalltheextenderafterthesourcehasbeensetupand
tested,andthenconrmthenewarrangementworks.
Binarymatrixswitchersaredesignedtodeliverunsurpassedtechnologywithsuperiorperformance.However,where
youinstalltheswitchercanhavealargeaffectontheperformancethatyoureceive,andthelifeoftheunit.Hereare
someguidelinestofollowwheninstallingaB-500-MTRX-230-4x4Switcher.
• Besurethattheunitisinawell-ventilatedareathatprovidesadequatecooling.
• Donotblockthecoolingventslocatedonbothsidesoftheunit.
• Donotplacetheunitoncarpetingoranysimilarmaterial.
• Donotinstalltheunitnearasourceofheat,orinanextremelyhumidorwetlocation.
• Ifyourinstallationlacksgoodairow(suchassolidcabinetdoorsorwall-mountedracks),itmaybenecessaryto
createventilationtoallowoutsideairintothespace.
• Allowaminimumof3”offreeairspaceoneithersideoftheunit.(Doesnotapplytorackmounting)
• Allowaminimumof2”ofdepthbehindunittoaccommodatecablesandconnectors.
• Whenplacingonacabinetshelf,positiontheunitwithallfeetrestingonasolidlevelsurface.
7.4.1. Rack Installation
TheB-500-MTRX-230-4x4canbemountedinarackwiththefrontorrearpanelfacingoutward,andwilldisplace1Uof
verticalspacewheninstalled.Rear-facinginstallationallowsforeasyaccesstotheconnectionsforinstallationsthatdo
notrequirethefrontpaneloftheunittobeaccessed.Front-facingmountingisusefulforapplicationswherethefront
panelmustbeaccessibleorvisible.
Therackearsarepackagedseparatelyfromthematrixswitcherinthebox.Attachtheearstothesidesofthematrixat
thefrontorbackusingtheincludedscrews.Tightenthemwitha#2PhillipsScrewdriver.Itmaybenecessarytoremove
thefeetfromthebottomwhenrackmountingthematrixswitcher.Removethescrewsforthefeetwitha#2Phillips
Screwdriver,andstorethefeetandscrewstogetherincasetheyareneededinthefuture.
Note: The rack ears and mounting holes are only designed to safely hold the weight of the B-500-MTRX-230-4x4.
Do not use the matrix switcher as a shelf for other equipment in the rack.
B-500-MTRX-230-4x4 Installation Manual
Pg. 9
www.snapav.com Support: 866.838.5052
7.5. HDMI Input Connections
7.6. Output Connections
EachofthefourinputsontheB-500-MTRX-230-4X4utilizesastandardHDMIportforconnection.Followtheseguidelines
when connecting sources to the inputs.
• Alwaysusetheshortestcablepossiblebetweensourceequipmentandthematrixswitcherinputs.Usehighspeed
ratedcablestoguaranteethebestpossibleperformance.
• AvoidusingHDMIcableadaptersinruns.Alwaysrunoneunbrokencablewhenpossible.
TheB-500-MTRX-230-4X4matrixswitcherisequippedwithoneHDMIandoneHDBaseToutputportforeachofthe4
outputzones.Seethesectionsbelowforspecicinstructionsanddetailsforeachconnectiontype.
Note: Any input selected on an output zone is played on both the HDMI and HDBaseT outputs for that zone simultaneously.
This can be used to feed the same source to two devices. Read more about this feature below.
7.6.1. Choosing the Correct Output
OutputstodisplayscanbeconnectedusinganHDMIcableoraCat5e/6cableandHDBaseTReceiver(withashort
HDMIcableconnectingtheReceivertothedisplay).Foranyrunoverabout50feet,orforanyoutputthatwillutilizeIR
pass-through,useHDBaseT.
ForshortrunswhereHDMIcablescanberoutedtothedisplayand/ornoIRpass-throughisneeded,orifthereisHDMI
equipmentconnectedbetweenthematrixoutputandthedisplay(likeanAVreceiver),itmaybebesttousetheHDMI
outputtoconnectequipment.
Insomesituationsitmaybebenecialtousebothoutputs.Iftwodisplaysneedtobefedthesamesourceatalltimes,
onedisplaycanbefedfromtheHDBaseToutput,andonefromtheHDMIoutput.InjobswithanAVreceiverfeeding
surroundsoundtoazone,theaudiocanbefedtothereceiverviaHDMI,andanHDBaseTreceivercanbeusedtoroute
videotothedisplay.ThisisbenecialwithAVreceiversthathaveolderorlessreliableHDMIscalingorpass-through.
7.6.2. HDMI Outputs
TouseanHDMIoutputtofeedadisplay,connectbetweentheoutputofthematrixswitcherandtheinputofthedisplay.
FollowtheguidelinesbelowwhenusingHDMIoutputsforthebestperformanceandreliability.
• Alwaysusetheshortestcablepossiblebetweenequipment.Usehighspeedratedcablestoguaranteethebest
possibleperformance.
• AvoidusingHDMIcableadaptersinruns.AlwaysrunoneunbrokenHDMIcable.
• WhenroutingHDMItoanAVreceiverforsurroundsound,thenoutofthereceivertoadisplay,makesuretosetthe
AVreceivertoanHDMImodewherethesignalwillnotbeprocessedorscaledtoadifferentformat.Thiswillavoid
signaltimingissuesthatcancauseintermittentsyncortotallossofsync.Contactthedevicemanufacturerfordetails
regarding HDMI setup.
B-500-MTRX-230-4x4 Installation Manual
Pg. 10
© 2013 Binary
7.6.3. HDBaseT Outputs
FollowtheseguidelineswhenselectingandinstallingtheHDBaseTcable,andthenfollowtheinstructionsafterwardto
completetheconnectionsforanoutput.
7.6.3.1. HDBaseT Wiring Recommendations
Cable Type- Shielded or Unshielded Cat5e/6
• CableDistanceLimitations:
Cat5e/ Cat6: Upto200ft
Cat6a: Upto230ft
• UseatleastCategory5ehigh-qualitytwistedpairsolidconductorcableratedtonolessthan350Mhzbandwidth.
Thehigherthecablestandard,thebetteritwillperform.
• Forthe bestresults installashieldedcable.Thiswill preventsignal dropoutandartifactsfrom beingcaused by
electromagneticandradiointerference(EMI/RFI)fromceilingfans,appliancesandelectricmotors.
• Usenomorethantwo5meterorshorter,solidorstranded,568Bterminatedpatchcablesintherun.Useshielded
patchcablesiftherunisshieldedtomaintainshieldcontinuity.
• Usenomorethantwokeystonesorcouplersintherun.Useshieldedkeystonesorcouplerswithshieldedcable
tomaintaincontinuity.
• Cleanlyterminateallcableendsandtesteverycableusedbeforeconnectingtheextendertoavoidtroubleshooting
terminationproblemslater.
• MarkeachendoftheHDBaseTcablewiththeincludedlabelstoavoidconfusionlater.
Connector Type- RJ45
• UseahighqualityRJ45connectorthatmatchesorexceedsthestandardofthecableinuse.Shieldedconnectors
mustbeusedwithshieldedcables,andmustmaintaincontinuityoftheshieldtobothconnectorstoprotectfrom
interference.
• Wehighlydiscouragetheuseof“EZ”style,openendRJ45swithHDMIextenders.
• AlwaysterminateRJ45connectorsintheHDBaseTsignalpathtothe568Bterminationstandardasrequiredby
HDBaseT standards.
7.6.3.2. Installation Instructions
1. InstalltheCat5e/6cableandterminatetheends.Thentestthecabletoensureoperation.
2. ConnecttheHDBaseTcabletothedesiredHDBaseToutputofthematrixswitcher.
3. ConnecttheHDBaseTcabletotheB-500-RX-230-IRReceiverortheHDBaseTdeviceinuse.
4. ConnectanHDMIcable(2metersorshorterisrecommended)betweentheHDMIOUTportontheReceiverand
thedesiredHDMIinputontheDisplay.
5. AttachthepowersupplytotheReceiverandpowertheunit.
6. Installationiscomplete.Testallconnectedinputsandoutputstogethertoensurereliableoperation.
7. ForIRPass-ThroughIntegration,seesection7.8.IRPass-ThroughInstallationandSetup,page12.
Pin 1 White/Orange Pin 5 White/Blue
Pin 2 Orange Pin 6 Green
Pin 3 White/Green Pin 7 White/Brown
Pin 4 Blue Pin 8 Brown
TIA/EIA Standard 568-B (Gold Pins Facing Up)
B-500-MTRX-230-4x4 Installation Manual
Pg. 11
www.snapav.com Support: 866.838.5052
LINK LINK
PWR
LINK LINK LINK LINK LINK LINK
Engineered in the USA
Manufactured in Taiwan
IR IN
ALL IR OUT
Matrix IR
Control Input
7.7. Matrix Control Connections
Alldrivers,associatedsoftwareandextradocumentationisavailableontheB-500-MTRX-230-4X4productpageat
www.SnapAV.comundertheSupportTab.
7.7.1. IR Control
The B-500-MTRX-230-4X4 can be controlled by IR from the front panel receiver or by
attaching a mono cable from the control system asher output to the “System IR In” port
onthebackofthematrixswitcher.Forthemostreliablecontrol,usetheSystemIRInport.
The matrix switcher will also process commands received on IR Receiver inputs from
B-500-RX-230-IRinzonesconnectedviaHDBaseT.(SeeSection7.10.2.IRPass-ThroughfromRoomstoSourceson
page15foranapplicationexampleofthisfeature.)
Note: System IR Control and the front panel IR Receiver can be disabled when not in use by using the Conguration
Utility. See the Conguration Utility manual section, “Other Settings” for more information.
7.7.2. RS232 Control
TocontroltheB-500-MTRX-230-4x4withRS232,thedevicesmustconnectusingthecorrectpincongurationforthe
controlsysteminuse.
Thematrixswitcherreceivescontroldataonpin2(RxD–DataReceive)andtransmitscontroldataonpin3(TxD-Data
Transmit).TheconnectioncablebetweenthematrixswitcherandtheAutomationSystemwillneedtobecongured
sothatpin2(RxD)ontheswitcherisconnectedtothecontrolsystemTxD(DataTransmit)pin,andpin3(TxD)onthe
switcherisconnectedtothecontrolsystemRxD(DataReceive)pin.Seethediagrambelowfordetails.
Congurationforcontrolsystemserialportscanvary.Refertothedocumentationforthesysteminusetoensureproper
connectionandconguration.
Note: This port is also used to communicate with a PC when using the PC Conguration Utility. Refer to the Conguration
Utility manual for details.
B-500-MTRX-230-4x4RS232PortConguration
LINK LINK
PWR
LINK LINK LINK LINK LINK LINK
Engineered in the USA
Manufactured in Taiwan
IR IN
ALL IR OUT
DB9 Female Connector
RxD (Data Receive)
TxD (Data Transmit)
GND
Pin Function
2 RxD(DataReceive)
3 TxD(DataTransmit)
5 Ground/Common
B-500-MTRX-230-4x4 Installation Manual
Pg. 12
© 2013 Binary
7.8. IR Pass-Through Installation and Setup
ToutilizeIRpass-throughbetweenadisplaylocationandthematrixswitcher,installaB-500-RX-230-IRatthedisplay
anduseHDBaseTforroutingthesignal.Thematrixswitcherandthematrixreceiverareequippedwithportstoallow
commandstobesenttothedisplayorfromthedisplayarea.ThissectiondetailsthepinoutsandcorrectuseoftheIR
pass-through ports.
7.8.1. Matrix Switcher IR Connections
Theportsindicatedinthediagramaredescribedindetailbelow.Guidesforstandardapplicationsareincludedonthe
followingpagesforreferenceduringsetup.
7.8.2.MatrixSwitcherIRPortConguration
AllIRconnectionportsontheB-500-MTRX-230-4X4are3.5mmmonominiandusethispinoutconguration.Consult
withthemanufacturerofanyattachedIRequipmenttoconrmtheirpinoutmatchesbeforeuse.
IR Signal (Tip)
GND (Sleeve)
IR Signal Tip
GND (Ground) Ring
1. IR Output to Source 1 through 4
TheIRoutputfromeachconnectedB-500-RX-230-IRistransmittedtotheIROUTPUTTOSOURCEports.
Commandscanberoutedtothesourceselectedortothelike-numberedport.
2. IR Input to Room 1 through 4
Use3.5mmmini-monocablestoconnectIRasheroutputsonacontrolsystemtotheseportstosendcommands
todisplaysorequipmentlocatedattheB-500-RX-230-IRmatrixreceiverlocation.Thenumbercorrespondstothe
outputzonenumber,soIRInputtoRoomport1willsendsignalstoHDBaseToutput1.
3. System All IR Out
ThisportrepeatsanycommandsentfromtheIRReceiverportsonB-500-RX-230-IRMatrixReceiversconnected
to any HDBaseT output.
4. System IR In
3.5mmmonominiIRinputportformatrixswitchIRcontrol.
LINK LINK LINK LINK
1 3
2 4
1 3
2 4
1 2 3 4
B-500-MTRX-230-4x4 Installation Manual
Pg. 13
www.snapav.com Support: 866.838.5052
7.9. B-500-RX-230-IR IR Connections
TheB-500-RX-230-IRIRportsaredescribedbelow.Usethediagramforreference.
7.9.1. IR Receiver
AttachanIRreceivertothisporttocaptureIRcommandsintheroomforpass-throughforsources.Thisportwillalso
sendcommandsbacktothematrixswitcherforcontrolofsourceselectionineachzone.
7.9.2. IR Flasher
AttachanIRashertothisportforcontrollingadisplayorotherequipmentwithcommandssentfromacontrolsystem
asheroutput,intothematrixswitcherIRINPUTTOROOMportsandthentothisport.
1 2
IR Signal (Tip)
GND (Ring)
12V DC (Sleeve)
IR Signal Tip
GND (Ground) Ring
+12V DC Sleeve
IR Signal (Tip)
GND (Sleeve)
IR Signal Tip
GND (Ground) Ring
7.9.3. Yellow Tag IR Adapter
Theyellowtaggedadapter(illustratedbelow)includedwiththeB-500-RX-230-IRisusedwhenplugginga3.5mm
monominicableintotheIRReceiverportoftheB-500-RX-230-IR.ThisisusedtosendIRcommandstothematrix
switcherlocationfromotherdevices,insteadofanIRReceiverthatusesa3.5mmmonominiportforoutput.
IR Signal (Tip)
GND (Ring)
12V DC (Sleeve)
IR Signal (Tip)
GND (Sleeve)
To IR Control System
or
Connecting Block
To B-500-MTRX
B-500-MTRX-230-4x4 Installation Manual
Pg. 14
© 2013 Binary
7.10. IR Application Diagrams
7.10.1. IR Pass-Through from Control System
ThediagramaboveillustratesatypicalinstallationwithaB-500-MTRX-230-4X4wherealloftheequipmentisbeing
controlledbyacontrolsystemthatusesRF(RadioFrequency)remotesineachoutputzone.
• TheRFremotestransmitcommandsbacktothecontrolsystemwhichthensendscommandstoeachdevicebeing
controlled. Custom programming by the installer sets the control system up to automatically switch inputs and
outputsinthematrixswitcherasneeded,sotheenduseronlyhastoselectthesourcetheywanttowatch.
• Eachdisplay(onlyoneispicturedforreference)requiringIRcontrolisconnectedtothesystemviatheHDBaseT
output ofthe matrix switcher. Cat5e/6 cableconnects to a B-500-RX-230-IR Receiver, which is attached tothe
displayviaHDMIforsignal.AnIRasherconnectedtotheIRasherportsendstheIRcommandstothedisplay.
Sourcesaredirectlycontrolledbythecontrolsystem.
• IR control for displays is routed from the control system to the matrix switcher using 3.5mm mono mini cables
pluggedintoIRINPUTTOROOMports.ThecommandspassfromamatrixswitcherporttotheHDBaseToutputof
thesamenumber.Inthediagramthemonocableusedtosendcommandstotheoutput4zoneispluggedintoIR
INPUTTOROOMport4.Thisallowsdiscretecontrolofeachdisplayconnected,eveniftheyaremodelswiththe
samecodes.
• SomedisplaysandprojectorscanbecontrolledbyothermethodsthanIR.TheprojectorpicturedfeaturesIPcontrol,
soitisreceivingcommandsfromthecontrolsystemoveranEthernetconnection.AnHDMIcableisconnectingitto
thematrixswitcheroutputsinceitisinstalledcloseenoughtotheequipmentandrequiresnoIRasher.
• Whenthesystemisinuse,iftwooutputsareconnectedtothesameinput,thesourcewillchangeonbothoutputs
withanycommandsentsinceitcan’tsendtwoHDMIstreamsatonce.Thismustbeconsideredwhendecidingon
thesourcestoconnectfordistribution.
Example: In a home with four displays connected, if users in every room want to watch satellite on different
channels, there must be four satellite receivers set up as sources. With custom programming, each output
can be programmed to use only one of the satellite source inputs, giving each output a dedicated cable box,
while allowing other less-used sources to connect to any output.
LINK LINK LINK LINK
1 3
2 4
1 3
2 4
24V DC 2.7A
IR Outputs
RS232
IR Inputs
B-500-RX-230-IR
Projector
HDMI
Cat5e/6
HDMI
PLAY
HDMI Source HDMI Source
HDTV
IR Flasher
Ethernet Connection
RS232
IR Flasher
IR Flasher
3.5mm Mono
C5e/6
Ethernet
Connection
Cat5e/6
B-500-MTRX-230-4x4 Installation Manual
Pg. 15
www.snapav.com Support: 866.838.5052
7.10.2. IR Pass-Through from Rooms to Sources
ThediagramaboveillustratesatypicalinstallationwithaB-500-MTRX-230-4X4wherealloftheequipmentisbeing
controlledbyIRremotesineachoutputzone.
• In each room with a connected display, an entry-level universal IR remote is being used to control the display
andsourcesinuse.CustomprogrammingsetupineachremotebytheinstallersendsIRcommandsoutofthe
remotemeantforthedisplaydeviceintheroom,thesources,andthematrixswitchersimultaneously.Thematrix
commandsareprogrammedtobesentautomaticallyasneededsotheenduseronlyhastoselectthesourcethey
want to watch.
• To make this system work seamlessly, two advanced IR options have been enabled in the matrix switcher
CongurationUtility“OtherSettings”menu:IRSourceRoutingandIRMatrixControlfromroom.
o IR Source Routing allows the commands from the room to be routed directly to the source selected to be
displayedintheroom.ThissimpliesIRroutingbecauseonlyoneasherhastoconnecttothesource.
o IRMatrixControlsetsthematrixswitchersothatanycommandsentfromanyHDBaseToutputtocontrolthe
matrixisautomaticallyreceivedinternally,eliminatingtheneedforanexternalconnectionbacktothematrix
forcontrol.SeeSection9.AdvancedSetupUsingtheCongurationUtilityonpage20formoreinformationon
changing these settings.
• Whenthecommandsaresent,thedisplaydeviceiscontrolleddirectlybytheremote.Thecommandsforthematrix
switcherandsources are pickedupbytheIR receiverconnected totheB-500-RX-230-IRand sent backtothe
correctIROUTPUTTOSOURCEportandtothematrix.
• Whenthesystemisinuse,iftwooutputsareconnectedtothesameinput,thesourcewillchangeonbothoutputs
withanycommandsentsinceitcan’tsendtwoHDMIstreamsatonce.Thismustbeconsideredwhendecidingon
thesourcestoconnectfordistribution.
Example: In a home with four displays connected, if users in every room want to watch satellite on different
channels, there must be four satellite receivers set up as sources. With custom programming, each output
can be programmed to use only one of the satellite source inputs, giving each output a dedicated cable box
while allowing other less-used sources to connect to any output.
LINK LINK LINK LINK
1 3
2 4
1 3
2 4
24V DC 2.7A
Projector
PLAY
HDMI Source HDMI Source
HDTV
IR Receiver
IR Receiver
B-500-RX-230-IR
IR Receiver
IR Receiver
HDMI
HDMI
IR Flasher IR Flasher
HDMI
B-500-RX-230-IR
HDMI
Cat5e/6Cat5e/6
B-500-MTRX-230-4x4 Installation Manual
Pg. 16
© 2013 Binary
8. EDIDConguration
8.1. Source Setup
8.2. Display Setup
8.3.AutoEDIDConguration
The displaysused within an installation usually varyfrom room to room,and some may not supportall resolutions
availablefromasource.Itisnecessarytomakesuresourceswillprovideavideoandaudioformatcompatiblewith
allconnecteddisplaysprogrammedtousethem.Toaccomplishthis,theB-500-MTRX-230-4X4includesbuilt-inEDID
managementforeachsourceinput.ThestoredEDIDispersource,soalldisplaylocationswillseethesameresolution
andhavethesameaudioformatwhenthatsourceisselected.
Note: Source is only able to output one video resolution and one audio format.
Note: The default EDID for each input is always 1080p with 2 channel stereo audio, since this format is accepted by
most displays with no issues.
ThefollowingsectionsexplainconguringEDIDsviatheincludedIRRemote.BeforeconguringtheEDID,besureto
refertothesourceanddisplaymanualsforavailablefeaturesandresolutionsforeachdevice.Formoreinformation
aboutusingtheincludedremote,seeSection11.1IRRemoteonpage21.
While all EDID congurations are available via the remote, the Conguration Utility can be used for faster setup.
DownloadtheCongurationUtilityandmanualontheSupportTabfortheB-500-MTRX-230-4X4atwww.SnapAV.com.
What is EDID? EDID, or Extended Display Identication Data, is a stream of information sent from a display to a source
when the two devices are connected to tell the source what video and audio formats the display can use. This prevents
sources from outputting media that won’t work with the display.
Checkeachsourceandconrmthattheaudioformatandvideoresolutionaresetsothattheywillchangebasedonthe
EDID.Normallythissettingiscalled“Auto”orsimilar.
Note: EDID setup is not required if the source supports setting one xed video resolution and audio format.
ItisrecommendedthatConsumerElectronicsControl(CEC)beturnedOFFinalldisplayswhenusingtheB-500-MTRX-
230-4X4.Thiswillprovideforpropercommunicationofvideo/audiosignalsandallowEDIDstofunctionattheiroptimum
performance.Refertothedisplay’smanualforinformationonhowtoturnthisfunctionOFF.
ThequickestandeasiestmethodforcongurationistouseAutoEDID.Whenthismodeisusedthematrixswitcher
looksattheEDIDfromeachoftheconnecteddisplays.Itusesthehighestcommonvideoresolutiontocreateanew
EDIDandsavesthatEDIDinalloftheinputs.
Note: Auto EDID sets audio to 2ch stereo for all inputs regardless of the capability of the connected displays. If multi-
channel audio is desired, embedded EDIDs or Learned EDIDs will need to be used.
When to use Auto EDID
• Allsourceswillbeavailableonalldisplays.
• Asarststeptoconguration,followingupwithadvancedmethodsforparticulardisplaysanddedicatedsources.
Note: For advanced EDID conguration when using a legacy display and/or dedicated sources, use embedded EDIDs
or learning as described in the following sections.
Sets EDID Based on All Connected Displays Display Readout (Example)
1.PressDEFAULT
E-
2.PressNumberKey9
AA
3.PressENTER
A0
8.3.1.HowtoCongureAutoEDID
TosetupAutoEDIDconguration,rstmakesurethatalldisplaysarepoweredonandconnectedtothematrixswitcher.
Then,pressthefollowingremotebuttonsinthisorder.Besuretopresseachbuttonwithin10secondsoftheprevious
button-presstopreventthecommandfromresetting.
B-500-MTRX-230-4x4 Installation Manual
Pg. 17
www.snapav.com Support: 866.838.5052
8.4.EmbeddedEDIDConguration
Inadditiontotheautomaticcongurationmethod,EDIDsintheB-500-MTRX-230-4X4canbesettoinputsmanuallyby
selectinganEDIDfromtheembeddedlist(defaultEDIDsprogrammedintothematrixswitcher).
Thematrixswitchercontainseight‘embedded’EDIDsthatmaybeassignedtoinputs.TheseEDIDsdenegroupsof
videoandaudiocapabilitiesthatareusefulforconguringsourcesinmostsystems.
8.4.1. Embedded EDID Chart
Explanation of Embedded EDIDs
Video ResolutionintheEmbeddedEDIDsisthehighestresolutionaconnectedsourcewilloutput.Thatis,ifthesource
iscapableof1080P@60itwillberequiredbyEDIDs1-6toprovidethatresolution.However,ifthesourceisonlycapable
of1080iitwilloutput1080i,etc.Itisassumedthatanydisplaythatcanacceptthespeciedvideoresolutioncanalso
acceptallstandardvideoresolutionslessthanthatspecied.
Color Depthisthemaximumnumberofbitsusedtoencodecolor.24bitcolordepthis8bitspercolor(red,blue,green).
36bitcolordepthis12bitspercolor(red,blue,green).
3Dindicatesthatthesourcecanoutput3Difitisavailableinthecontent.
Audio Format indicatesthemaximumnumberofaudiochannels,aswellastheaudioformatthatthesourceisallowed
tooutput.ForanEmbeddedEDIDwith7.1chAudioFormat,thesourcedevicewilloutputthehighestaudiopossible
basedonthecontent.Forexample,if7.1chisnotavailableand5.1chisavailable,thentheoutputwillbe5.1ch.The
sameistrueif2chstereoistheonlyaudioavailablefromthesource.EmbeddedEDIDswith2chstereowilllimitoutput
tothataudioformatregardlessofwhatisavailableinthecontent.
Embedded EDIDs 7 and 8areprovidedforlegacydisplaysthatcanonlyacceptresolutionsuptoamaximumof1080i/
720p.The1080iislistedrstsincealmostallolderHDdisplayscanaccept1080ibutnotallcanaccept720p.Forthese
twoEmbeddedEDIDs,(7&8)thesourcewilloutput1080i.Should1080inotbeavailable,thesourcewilloutput720p.
Note: There is a possibility that 720p may not work for a very small number of older displays that may still be in use. It
will be necessary to use a Learned EDID from the display to store in the Input EDID of any sources that will be
routed to that display if 720p is not supported. See Section 8.5. EDID Learning on page 18 for directions to set a
learned EDID.
When to Use Embedded EDIDs
• Formostcurrentdisplaysandsources,usingembeddedEDID#2isrecommendedunlessmultichannelaudiois
needed.Inthatcase,useembedded#3.TheotherembeddedEDIDsareusefulforsupportinglegacyequipment.
Embedded EDID Resolution Color Depth Audio
1 1080p@60Hz 24-Bit 7.1ch
2(FactoryDefault) 1080p@60Hz 24-Bit 2ch
3 1080p@60Hz 24-Bit 3D 7.1ch
4 1080p@60Hz 24-Bit 3D 2ch
5 1080i@60Hz 36-Bit 3D 7.1ch
6 1080i@60Hz 36-Bit 3D 2ch
7 1080i@30Hz/720p@60Hz 24-Bit 7.1ch
8 1080i@30Hz/720p@60Hz 24-Bit 2ch
B-500-MTRX-230-4x4 Installation Manual
Pg. 18
© 2013 Binary
8.4.2. How to Set Embedded EDID for a Single Input
8.5.1. How to Learn EDID to a Single Input
8.4.3. How to Set Embedded EDID for All Inputs
Example: Input =1 Embedded EDID=4 Display Readout (Example)
1. PressDEFAULT
E-
2. PressNumberKey(1-8)toselectoneEmbeddedEDID
4A
3.PressINPUT
4A
4. PressNumberKey(1-4)toselecttheInputtowhichtheEDID
isapplied
41
5. PressENTER
(success)
(fail)
--
FF
Example: Input =1 Embedded EDID=4 Display Readout (Example)
1. PressDEFAULT
E-
2. PressALLtoselectallInputs
A-
3.PressNumberKey(1-8)toselectEmbeddedEDID
4A
4. PressENTER
(success)
(fail)
--
FF
8.5. EDID Learning
FormoreadvancedEDIDconguration,learningcanbeusedtoassignEDIDsdirectlyfromdisplaystooneormore
inputs.Thisisusefulwhenthesystemcontainsadisplaythatcannotacceptthehighestresolutionavailablefrom
sources,butallsourcesneedtobeavailabletoalldisplays.
Note: EDIDs can be learned from displays connected via the HDBaseT or the HDMI output.
When to Use Learned EDIDs
• AnolderdisplaydoesnotworkproperlywithanyoftheembeddedEDIDs.
• WhenthesourceisaPCitmaybenecessarytousealearnedEDID.
• LearningEDIDtoasingleinput
Example: Input =1 EDID Learned from Output 4 Display Readout (Example)
1. PressLEARNonceforHDMIportortwiceforHDBaseTport
L.-.
2.PressOUTPUT
1A
3.PressNumberkey(1-4)toselecttheOutputtheEDIDis
learnedfrom
14
4.PressINPUT
L-
5.PressNumberKey(1-4)toselecttheInputtowhichtheEDID
isapplied
1A
6.PressENTER
(success)
(fail)
--
FF
B-500-MTRX-230-4x4 Installation Manual
Pg. 19
www.snapav.com Support: 866.838.5052
8.5.2. How to Learn EDID to All Inputs
--
FF
Example: Input=All EDID Learned from Output 4 Display Readout (Example)
1.PressLEARN
L.-.
2.PressOUTPUT
L-
3.PressNumberKey(1-4)toselecttheOutputtheEDID
islearnedfrom
4A
4.PressENTER
(success)
(fail)
8.6. Viewing Input EDID Status
IfthereisaquestionabouttheEDIDsetforaninput,thestatusofthatinput’sEDIDcanbereviewedusingthe
includedIRremoteandwatchingthematrixswitcherfrontpaneldisplay.
Notes about EDID Status
• IftheEDIDwaslearnedfromanoutput,theexactEDIDspecicationswillnotbeshown,buttheoutputnumberwill
beidentied.Reviewthespecicationsofthedisplayattachedtotheoutputtodetermineitscompatibleresolutions.
• If the second digit (the Input being queried) has a dot after it, then the rst digit is the EDID number from the
EmbeddedEDIDtable.
• Iftheseconddigit(theInputbeingqueried)doesnothaveadotafterit,therstdigitistheOutputtheEDIDwas
learnedfrom(step4fromexampleabove).
Example: View the EDID for Input 3.
DisplayReadout(Example)
EDID5Assigned
fromEmbedded
EDIDTable
EDIDLearned
fromOutput4
1.PressSTATUS
-- --
2.PressINPUT
-- --
3. PressNumberKey(1-8)toselectthedesiredInput
-3 -3
4.PressENTER
5.3. 4.3
B-500-MTRX-230-4x4 Installation Manual
Pg. 20
© 2013 Binary
9. AdvancedSetupUsingtheCongurationUtility
10. Firmware Update
There are several setup options available that can only be modied using the matrix switcher Conguration Utility.
Theseitemsaredefaultedtothemostcommonsettingsthatshouldworkinmostinstallations.
TheCongurationUtilityandmanualareavailablefordownloadontheSupportTaboftheB-500-MTRX-230-4X4product
pageatwww.SnapAV.com.DownloadandruntheUtilitytogainaccesstothesesettingsbyconnectingtothematrixand
clicking“OtherSettings.”
BinarymayoccasionallyreleasenewrmwarefortheB-500-MTRX-230-4X4toaddressnewstandardsandtechnology.
Itwillneverbenecessarytoperformanupdatetoanexisting,correctlyfunctioningsystem,butduringinstallationor
serviceitisrecommendedtochecktheinstalledversiontobesureitisthenewestavailable.
Forfullupdateinstructions,seethesectiontitled,“FirmwareUpdate”intheCongurationUtilitymanual.Newrmware,
the Conguration Utility, and the Conguration Utility manual are available for download on the Support Tab of the
B-500-MTRX-230-4X4productpageatwww.SnapAV.com.
9.1. IR Source Routing
9.2. IR Front Panel IR Enable
9.4. Front Panel Power Button Active
9.3. Matrix Control from Room Enable
TheIRSourceRoutingfeatureallowsdiscretecontrolofthesourceselectedfromanyconnectedHDBaseToutputusing
anIRreceiverpluggedintotheB-500-RX-230-IR.Thissettingisonlyrelevantwhenusingin-roomIRremotestocontrol
sourcesconnectedtothematrixswitcher.WhensettoYes,thematrixwillroutecommandsfromtheHDBaseTReceiver
totheIROutputtoSourceportthatmatchesthesourceinputnumbercurrentlyselectedonthatoutput.
WhensettoNo,commandswillbesentonlyoutoftheIROutputtoSourceportthatmatchestheHDBaseTReceiver
numberfromwhichitoriginated.
ThissettingcontrolstheoperationofthefrontpanelIRreceiverbuiltintotheB-500-MTRX-230-4X4.Thisshouldbe
disabledifusingtheSYSTEMIRINporttocontrolthematrixswitcherviaIR,orifthematrixswitcherismissingor
receivingextracommandsduringuse(strayIRinterferingwiththeport).
TheFrontPanelPowerButtoncanbedisabledifdesired.Disablethebuttonwhenthematrixswitcherisprogrammedto
beonatalltimesorinjobswhereturningoffthematrixfromtheswitchercancauseissueswithcontrol.
TheMatrixControlfromRoomEnableoptionallowsMatrixControlIRcommandstobesentfromtheroomasifasource
werebeingcontrolled.Turnthisoptionoffifthematrixswitcherisbeingcontrolledbyanyothermethodthanin-roomIR.
Note: To use Matrix Control from Room, it is recommended to program a universal remote control with discrete commands
for matrix control to keep in each zone, rather than using the included IR remote or commands learned from it.
Go to the Support Tab of the B-500-MTRX-230-4X4 product page at www.SnapAV.com to see and download the
available IR codes and drivers for IR remote programming.
Default Setting: Yes
Default Setting: Yes
Default Setting: Yes
Default Setting: Yes
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Binary B-500-MTRX-230-16x16 Installation guide

Category
Supplementary music equipment
Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI