ATEN VE849 User manual

Type
User manual

This manual is also suitable for

ATEN VE849R is a multicast HDMI wireless receiver, designed to transmit uncompressed 1080p video and digital audio signals wirelessly up to 30 meters. It supports up to 4 receivers, allowing multiple displays to be connected simultaneously. With plug-and-play installation and no software required, it's perfect for use in home theater, corporate training, and digital signage applications.

ATEN VE849R is a multicast HDMI wireless receiver, designed to transmit uncompressed 1080p video and digital audio signals wirelessly up to 30 meters. It supports up to 4 receivers, allowing multiple displays to be connected simultaneously. With plug-and-play installation and no software required, it's perfect for use in home theater, corporate training, and digital signage applications.

Multicast HDMI Wireless Extender
VE849
User Manual
www.aten.com
VE849 User Manual
ii
EMC Information
FEDERAL COMMUNICATIONS COMMISSION STATEMENT:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
KCC Statement:
RoHS
This product is RoHS compliant.
© Copyright 2020 ATEN® International Co., Ltd.
Manual Date: 2020-12-16
ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved.
All other brand names and trademarks are the registered property of their respective owners. The
terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing Administrator, Inc.
VE849 User Manual
iii
1. 1.The frequency and maximum EIRP Power in EU are listed as below
Transmitter:
5.19 ~ 5.31GHz:22.63dBm
5.51 ~ 5.67GHz:22.71dBm
Receiver:
5.18 ~ 5.24GHz:21.88dBm
5.19 ~ 5.31GGz:21.92dBm
5.51 ~ 5.67GHz:21.86dBm
2. 2.Operations in the 5.15~5.35GHz band are restricted to indoor usage
only.
This equipment should be installed and operated with a minimum distance
of 20 cm between the radiator and your body.
Dieses Gerät sollte mit einem Mindestabstand von 20 cm zwischen dem
Kühler und Ihrem Körper installiert und betrieben werden.
You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement:
1. 1.This Transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
2.This equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20 centimeters between the radiator and your
body.
VE849 User Manual
iv
User Information
Online Registration
Be sure to register your product at our online support center:
Telephone Support
For telephone support, call this number:
User Notice
All information, documentation, and specifications contained in this manual
are subject to change without prior notification by the manufacturer. The
manufacturer makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties as to merchantability or fitness for any particular purpose. Any of
the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and
not the manufacturer, its distributor, or its dealer), assumes the entire cost of all
necessary servicing, repair and any incidental or consequential damages
resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV
interference caused by unauthorized modifications to this device. It is the
responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation
of this system if the correct operational voltage setting was not selected prior
to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
International http://eservice.aten.com
International 886-2-8692-6959
China 86-10-5255-0110
Japan 81-3-5615-5811
Korea 82-2-467-6789
North America 1-888-999-ATEN ext 4988
United Kingdom 44-8-4481-58923
VE849 User Manual
v
Package Contents
The VE849T package consists of:
1 VE849T HDMI Wireless Transmitter
1 IR Remote Control with 2 AAA Batteries
1 IR Blaster Cable
1 Power Adapter (VE849T)
1 User Instructions*
The VE849R package consists of:
1 VE849R Multicast HDMI Wireless Receiver
1 Mini USB Power Adapter (VE849R)
1 IR Receiver Cable
1 HDMI Cable
1 User Instructions*
Note: The VE849T and VE849R are sold separately.
Check to make sure that all the components are present and that nothing got
damaged in shipping. If you encounter a problem, contact your dealer.
Read this manual thoroughly and follow the installation and operation
procedures carefully to prevent any damage to the unit, and/or any of the
devices connected to it.
* Features may have been added to the VE849 since this manual was
published. Please visit our website to download the most up-to-date version.
VE849 User Manual
vi
Contents
EMC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iv
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
About this Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ix
Chapter 2.
Introduction
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Source Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Display Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
VE849T Transmitter Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
VE849R Receiver Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
VE849T Transmitter Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
VE849R Receiver Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
IR Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 3.
Hardware Setup
VE849T - Transmitter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
VE849R - Receiver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
IR Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 4.
Operation
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
IR Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
POWER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
INFO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
IR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
RX PAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
EDID Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appendix
VE849 User Manual
vii
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
International. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
North America . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
VE849 User Manual
viii
About this Manual
This User Manual is provided to help you get the most from your system. It
covers all aspects of installation, configuration and operation. An overview of
the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the VE849 system. Its purpose,
features and benefits are presented, its front and back panel components and
remote control are described.
Chapter 2, Hardware Setup, describes how to set up your installation. The
necessary steps needed to install the transmitter, receiver, and IR blaster are
explained.
Chapter 3, Operation, explains the fundamental concepts involved in
pairing transmitters and receivers, and operating the VE849, IR Blaster cable,
remote control and EDID management.
An Appendix, provides specifications, troubleshooting, and other technical
information regarding the VE849.
VE849 User Manual
ix
Conventions
This manual uses the following conventions:
Product Information
For information about all ATEN products and how they can help you connect
without limits, visit ATEN on the Web or contact an ATEN Authorized
Reseller. Visit ATEN on the Web for a list of locations and telephone numbers:
Monospaced Indicates text that you should key in.
[ ] Indicates keys you should press. For example, [Enter] means to
press the Enter key. If keys need to be chorded, they appear
together in the same bracket with a plus sign between them:
[Ctrl+Alt].
1. Numbered lists represent procedures with sequential steps.
Bullet lists provide information, but do not involve sequential steps.
Indicates selecting the option (on a menu or dialog box, for
example), that comes next. For example, Start
Run means to
open the Start menu, and then select Run.
Indicates critical information.
International http://www.aten.com
North America http://www.aten-usa.com
VE849 User Manual
x
This Page Intentionally Left Blank
1
Chapter 1
Introduction
Overview
The VE849 Multicast HDMI Wireless Extender extends your HDMI display
up to 30m* from the HDMI source to up to four separate receivers using
wireless technology. Easily connect two HDMI source devices, a local HDTV
and up to four receivers connected to HDTVs – wirelessly with crystal clear
image quality capable of streaming Full 1080p with 5.1 channel Dolby digital
audio and 3D technology. Supporting Dynamic Frequency Selection (DFS),
the VE849 is able to operate within the U-NII Worldwide radio band (operating
within this regulated and less commonly used range greatly reduces Wi-Fi
signal interference and improves transmission quality and stability). The
included IR remote control allows you to switch between HDMI source
devices from the receiver side, remotely; and allows you to watch a local and
four wirelessly connected HDTV- simultaneously. The VE849 consists of a
wireless audio/video transmitter and receiver. Consolidate your HDMI
electronics and use the VE849 as a wireless 2-port HDMI switch to connect
remote devices such as Blu-ray players and HD Cable boxes to design your
own custom wireless entertainment space.
* Distance may vary depending on the actual environment; solid objects such
as steel, concrete, or brick may cause interference and shorten the
transmission distance.
VE849 User Manual
2
Features
Wirelessly extend four HDMI displays up to 30m from the HDMI source*
Setup five HDTVs and view HD content on five HDTVs simultaneously*
Connect and transmit wireless video content from your Blu-ray DVD
player, HD Cable box or other HDMI device wirelessly
Multicast signal – 1 transmitter streams HDMI transmissions to 4
receivers simultaneously
Supports Dynamic Frequency Selection (DFS) - greatly reduces Wi-Fi
signal interference for improved transmission quality and stability
HDMI compliant
Wireless 3D Supported
Wireless HD in Full 1080p and 5.1 channel Dolby with AC3 and DTS
digital audio
Video Resolutions: 480p, 720p, 1080i and 1080p (24 / 30 / 60fps)
Local Transmitter: 2 HDMI Inputs and 1 HDMI Output
Remote Receiver: 1 HDMI Output
Keep home theater electronic devices neatly out-of-sight
Supports video games consoles with less than 1ms latency
Built-in IR receiver allows control of source devices from the remote side
No software or driver installation needed
HDCP Compliant
Based on WHDI™ Technology - Low latency <1ms
* Distance may vary depending on the actual environment; solid objects such
as steel, concrete, or brick may cause interference and shorten the
transmission distance.
1. Introduction
3
Requirements
Source Device
A source player with an HDMI Type A output connector
Display Device
A display device or receiver with an HDMI Type A input connector
VE849 User Manual
4
Components
VE849T Transmitter Front View
VE849R Receiver Front View
No. Component Description
1 Port LED The selected port LED (Blue) lights up to indicate that the
port is selected for use.
2 Port Selection
Pushbutton
The port selection pushbutton switches the VE849 between
the two connected HDMI media sources.
3 Power
Pushbutton / LED
Press this button to turn the VE849 on / off. The blue LED
indicates the VE849 is powered on,. The red LED indicates
the VE849 is in power saving mode.
1
2
3
4
4
3
2
1
1. Introduction
5
4 IR Receiver This receives the signals from the IR remote control.
No. Component Description
VE849 User Manual
6
VE849T Transmitter Rear View
VE849R Receiver Rear View
No. Component Description
1 Tripod Bracket Use this bracket to mount the VE849 to a tripod.
2 Power Jack The power adapter cable plugs in here.
3 HDMI In The cables from the HDMI source devices plug into these
ports.
4 HDMI Out Plug the local HDMI display into this port.
5 IR Blaster Port Plug the IR Blaster cable that came with your unit into this
port.
6 Service Port This port is used by the manufacturer to service the VE849.
7 USB Mini Power
Adapter Port
The Mini USB Power Adapter that came with your unit plugs
in here.
8 HDMI Out Plug the remote HDMI display into this port.
9 IR Receiver This receives signals from the IR remote control.
1
2
3
4
6
5
1
7
8
9
1. Introduction
7
IR Remote Control
No. Component Description
1 Power Press to turn transmitter and receiver on or off.
2 Info Press to show on-screen display (OSD) information on the
HDTV connected to the receiver.
3 IR Press to switch the IR Blaster frequency to meet the media
source devices requirements. Please refer to your source
devices IR specifications for the correct frequency.
The IR Blaster frequency ranges from 47KHz to 56KHz, to
38KHz recurring. The default is 47KHz.
4 RX Pair Press this key twice to have a receiver (VE849R) enter
pairing mode.
5 Source Press to switch between the media sources connected to
the transmitters HDMI In ports.
1
3
2
4
5
VE849 User Manual
8
This Page Intentionally Left Blank
9
Chapter 2
Hardware Setup
To install the VE849 Multicast HDMI Wireless Extender, refer to the
installation diagrams below as you preform the following steps:
VE849T - Transmitter Installation
1. Use an HDMI cable to connect the HDMI source device(s) to the HDMI
input port(s) on the rear of the VE849T.
2. Use an HDMI cable to connect the local HDMI video display (HDTV) to
the HDMI output port on the rear of the VE849T.
3. Plug the provided power adapter into an appropriate power source; plug
the power adapter cable into the power jack on the VE849T.
4. Connect the IR Blaster cable included with your package into the IR
Blaster port (see IR Cable Installation, page 10). (Optional)
1. Important safety information regarding the placement of this
device is provided on page 21. Please review it before
proceeding.
2. Make sure that the power to all devices connected to the
installation are turned off.
1
2
3
4
VE849 User Manual
10
VE849R - Receiver Installation
1. Place the VE849R receiver up to 30m from the VE849T transmitter.
2. Use the HDMI cable included with this package to connect the HDMI
video display (HDTV) to the HDMI output port on the rear of the VE849R
receiver.
3. Plug the provided Mini USB Power Adapter into an appropriate power
source; plug the power adapter cable into the USB port on the VE849R.
4. Connect the IR Blaster cable included with your package into the IR
Blaster port (see IR Cable Installation, page 10). (Optional)
5. Repeat these steps to install up to 4 receivers (VE849R).
IR Cable Installation
The IR Blaster cable allows you to use a source device’s remote control from
the receiver side of the installation. To install the IR Blaster, do the following:
1. Plug the IR Blaster cable into the IR Out port on the rear of the transmitter.
2. Connect the IR Sensor Extender Cable to the IR In port on the VE849R,
and attach the IR sensor to a visible area for IR remote control operation.
2
3
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37

ATEN VE849 User manual

Type
User manual
This manual is also suitable for

ATEN VE849R is a multicast HDMI wireless receiver, designed to transmit uncompressed 1080p video and digital audio signals wirelessly up to 30 meters. It supports up to 4 receivers, allowing multiple displays to be connected simultaneously. With plug-and-play installation and no software required, it's perfect for use in home theater, corporate training, and digital signage applications.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI