–
INSTRUCTION MANUAL
PS4 – JUGGERNAUT VER 5.1
Congratulations, welcome to the GamerModz Family! You are now a proud owner of a GamerModz Custom
Modded Controller.
The JUGGERNAUT - VER 5.1 FOR PS4 has been completely redesigned from the ground up to maximize your
gameplay experience. It includes a much faster processor allowing you turn mods on and off much quicker than
previous releases. Additionally, we have added many new mods as well as an on/off feature that allows you to
use the controller as standard controller without the possibility of accidently turning a mod on.
Your new GamerModz JUGGERNAUT Controller includes the following mods (Note you must be in the
Juggernaut Mode to enable these mods. See Page 2):
Rapid Fire (15 Pre-Set Modes) ................................................................................................. Page 2
Adjustable Rapid Fire (5 Programmable Modes) .................................................................... Page 3
Left Trigger Rapid Fire ............................................................................................................. Page 6
Dual Trigger Rapid Fire (Akimbo) ............................................................................................ Page 6
Jitter Mod ................................................................................................................................ Page 7
Jump Shot ................................................................................................................................ Page 8
Boost Shot ............................................................................................................................... Page 8
Max Boost Shot ....................................................................................................................... Page 8
Auto Drop ................................................................................................................................ Page 9
Drop Shot ................................................................................................................................. Page 9
Slide Shot ................................................................................................................................. Page 9
Auto Run ................................................................................................................................ Page 10
Double Tap ............................................................................................................................ Page 10
Auto Burst (4 Modes) ............................................................................................................ Page 11
Auto Aim ................................................................................................................................ Page 12
Auto Breath ........................................................................................................................... Page 12
Quick Scope (5 Programmable Modes) ................................................................................. Page 13
Fast Reload (5 Programmable Modes) .................................................................................. Page 15
Zombie Mode ........................................................................................................................ Page 18
Toggle L1/R1 and L2/R2 ......................................................................................................... Page 19
Remappable Pro Buttons (Optional Add On) ........................................................................ Page 20
IMPORTANT: Verify that your GamerModz Juggernaut Controller is Version 4 by following the instructions
below. The LED will flash 5 times indicating Version 5.
, then
–
*** IMPORTANT ***
TOP LEVEL MODES
All GamerModz Controllers have been redesigned to have a top level on/off feature. Your JUGGERNAUT
controller is designed with the following top level modes:
Mode 1: Juggernaut Mod
Mode 2: Zombie Mode
Mode 3: Off (All Mods Disabled)
IMPORTANT: When you first power on your controller, you will begin in Mode 3.
To change modes, hold down the Left Thumbstick and tap the Right on the D-Pad the number of times
corresponding to the mode you would like, then release the Left Thumbstick . The LED will flash the number
of times corresponding to the mode selected.
RAPID FIRE MODES
Your GamerModz Controller comes with 20 Rapid Fire Modes. Modes 1 thru 5 are custom programmable
modes that are user re-programmable for quick access. Modes 6 thru 20 are preset modes ranging from 6 shots
per second to 20 shots per second.
, then
, then
–
SELECTING A RAPID FIRE MODES
To enter a rapid fire mode, Hold Down the Right Trigger , and tap Up on the D-Pad the amount of
times corresponding to the mode you would like to enter, then Release the Right Trigger . The PS4
Controller LED will flash the number of times corresponding to the mode you selected.
MODE 1 ---------------- X 1
CUSTOM
MODE 11 ----------------- X 11
11 SHOTS PER SECOND
MODE 2 ---------------- X 2
CUSTOM
MODE 12 ----------------- X 12
12 SHOTS PER SECOND
MODE 3 ---------------- X 3
CUSTOM
MODE 13 ----------------- X 13
13 SHOTS PER SECOND
MODE 4 ---------------- X 4
CUSTOM
MODE 14 ----------------- X 14
14 SHOTS PER SECOND
MODE 5 ---------------- X 5
CUSTOM
MODE 15 ----------------- X 15
15 SHOTS PER SECOND
MODE 6 ---------------- X 6
6 SHOTS PER SECOND
MODE 16 ----------------- X 16
16 SHOTS PER SECOND
MODE 7 ---------------- X 7
7 SHOTS PER SECOND
MODE 17 ----------------- X 17
17 SHOTS PER SECOND
MODE 8 ---------------- X 8
8 SHOTS PER SECOND
MODE 18 ----------------- X 18
18 SHOTS PER SECOND
MODE 9 ---------------- X 9
9 SHOTS PER SECOND
MODE 19 ----------------- X 19
19 SHOTS PER SECOND
MODE 10 ------------- X 10
10 SHOTS PER SECOND
MODE 20 ----------------- X 20
20 SHOTS PER SECOND
TURN ON/OFF RAPID FIRE QUICKLY
To enable/disable Rapid Fire, Hold Down the Right Trigger , Tap Down on D-Pad , then Release the
Right Trigger .
Note: If you turn Rapid Fire on this way, the Juggernaut Controller will default to the last Rapid Fire Mode
enabled.
, then
X times
Mode #
, then
, then
–
ADJUSTABLE RAPID
FIRE MODES
Your GamerModz Juggernaut Controller comes with 5 Programmable Modes - Modes 1 thru 5. To program a
Mode, you must first select the mode (Reference “Toggle Between Rapid Fire Modes” on Page 2).
Once you are in the Mode you wish to Program (Only applies to Modes 1 thru 5) follow the instructions below
to Program that Mode. Your GamerModz Juggernaut Controller will remember the Re-Programmable Mode
settings even after you turn your controller off.
PROGRAMMING ADJUSTABLE RAPID FIRE MODES
Once you are in the Mode you wish to Program, Hold Down the Right Trigger , then Hold Up on D-Pad
until the LED begins to flash. Release both the Right Trigger and Up on D-Pad .
Once in Programming Mode you can adjust your shots per second by Tapping Up on D-Pad to Increase
Shots per Second and by Tapping Down on the D-Pad to Decrease Shots per Second. Note: Each time
you Tap the D-Pad, your Rate of Fire will Increase or Decrease 1 Shot per Second.
To test the Rapid Fire Rate, fire your weapon by pulling the Right Trigger . Adjust your Rapid Fire Rate by
Tapping Up or Down on the D-Pad until the desired smoothness and rate of fire is achieved. Please
see graph on Page 4 for Reference.
Once you have the desired Rapid Fire Setting, Tap Right on D-Pad to lock in the rate of fire. The PS4 LED
will flash the number times corresponding to your rate of fire. For Example: 12 Shots per Second, The LED will
flash 12 times.
, then
= Lock Rate of Fire
= Decrease Rate of Fire
= Increase Rate of Fire
Until LED
Begins to Flash
, then
–
OPTIMIZING
ADJUSTABLE RAPID FIRE
The below graph is a visual representation on how Adjustable Rapid Fire works for your GamerModz Juggernaut
Controller. This will help you manually adjust your Rapid Fire to the optimal rate of fire by understanding how
GamerModz Rapid Fire works.
Notes:
It is possible for the Rapid Fire to be so fast that it does not register in the game. If this occurs, try
slowing it down at times.
Slowing automatic weapons down to reduce recoil and increase accuracy can be effective too.
Faster than Max Fire Rate
Weapon is Stuttering or Not Firing at All
MAX Weapon Fire Rate
Weapon is Firing too Slowly
Slower than MAX Fire Rate
–
LEFT TRIGGER RAPID FIRE MOD
Left Trigger Rapid Fire allows you to assign rapid fire to your left trigger only. Note: You must first have a Rapid
Fire Mode turned on (See Page 2) to enable Left Trigger Mod.
To enable/disable Left Trigger Rapid Fire, Hold Down the Left Trigger and Tap Down on the D-Pad .
Then Release Left trigger . The PS4 Controller LED will flash one time to indicate that the Left Trigger
Rapid Fire Mode has been toggled on/off.
DUAL TRIGGER RAPID FIRE MOD (AKIMBO)
Dual Trigger Rapid Fire (Akimbo) allows you to assign rapid fire to both the Left Trigger and Right Trigger, giving
you a greater advantage when dual wielding. Note: You must first have a rapid fire mode turned on (See Page
2).
To enable/disable Dual Trigger Rapid Fire (Akimbo), Hold Down the Left Trigger and Right Trigger and
Tap Down on the D-Pad . Then Release Both Triggers . The PS4 Controller LED will flash one
time to indicate that the Dual Trigger Rapid Fire Mode has been toggled on/off.
, then
, then
, then
, then
–
JITTER MOD
The Jitter Mod Is designed specifically for Black Ops 3. It allows you to hip fire various weapons as fully
automatics. Please note you must have the Juggernaut Mod Enabled before being able to use Jitter.
Important Notes:
1. You must have the Gung Ho Perk in your Class
2. You must have a Tactical to use Jitter (We Recommend Shock Charge)
3. Enabling a Mod that does not work with Jitter (See Page 17) will disable Jitter.
4. The Jitter Mod is a Glitch – and the very nature of the glitch is that sometimes it will be glitch during use.
5. Holding down Left Trigger will temporarily disable Jitter. This is good for guns that can perform well
when zoomed in as well as hip fire Jitter (For Example: Shiva, XR-2, Drakon, 48 Dredge, etc.)
CHOOSING A JITTER MODE
To select a Jitter Mode, Hold Down the Button and Tap a Direction on the D-Pad (See Below)
corresponding to the desired mode. Then Release the Button. The XBOX One Controller LED will flash
one time to indicate that the mod has been enabled. Note: You can switch between Jitter Modes without
disabling the current Jitter Mode by selecting the mode you want to use.
MODE
D-PAD DIRECTION
WEAPONS
MODE 1
D-PAD LEFT
SHIVA / 205 BRECCI / HAYMAKER / 48 DREDGE / DRAKON
MODE 2
D-PAD UP
PHARO
MODE 3
D-PAD RIGHT
KRM-262 / ARGUS
OFF
D-PAD DOWN
NONE
*The Juggernaut 5.1 is an update following the patch by Call of Duty in an attempt to fix jitter. If you have
5.0, only Mode 3 will work.
TURNING OFF THE JITTER MOD
To disable the Jitter Mod, Hold Down the Button and Tap Down on the D-Pad . Then Release the
Button. The XBOX One Controller LED will flash one time to indicate that the mod has been disabled.
, then
, then
–
JUMP SHOT MOD
The Jump Shot Mod allows you to jump and fire at the same time by simply pulling the Right Trigger .
To enable/disable Jump Shot, Hold Down the X Button , Tap Right on D-Pad , then Release the Right
toggled on/off.
BOOST SHOT MOD
The Boost Shot Mod allows you to boost jump using 50% of your boost and fire at the same time by simply
pulling the Right Trigger .
To enable/disable Boost Jump Shot, Hold Down the X Button , Tap Up on D-Pad , then Release the X
Button . The PS4 Controller LED will flash one time to indicate that the Boost Jump Shot Mod has been
toggled on/off.
MAX BOOST SHOT MOD
The Max Boost Shot Mod allows you to boost jump using 100% of your boost and fire at the same time by
simply pulling the Right Trigger .
To enable/disable Max Boost Jump Shot, Hold Down the X Button , Tap Left on D-Pad , then Release
the X Button . The PS4 Controller LED will flash one time to indicate that the Jump Shot Mod has been
toggled on/off.
, then
, then
, then
, then
, then
, then
–
AUTO DROP MOD
The Auto Drop Mod allows you to drop to the ground quickly by simply tapping the O Button .
To enable/disable Auto Drop, Hold Down the O Button , Tap Right on D-Pad , then Release the O
Button . The PS4 Controller LED will flash one time to indicate that the Auto Drop Mod has been toggled
on/off.
DROP SHOT MOD
The Drop Shot Mod allows you to drop to the ground and fire at the same time by simply pulling the Right
Trigger .
To enable/disable Drop Shot, Hold Down the O Button , Tap Right on D-Pad , then Release O Button
The PS4 Controller LED will flash one time to indicate that the Drop Shot Mod has been toggled on/off.
SLIDE SHOT MOD
The Drop Shot Mod allows you to drop to the ground and fire at the same time by pulling the Right Trigger .
To enable/disable Slide Shot, Hold Down the O Button , Tap Left on D-Pad , then Release O Button
The PS4 Controller LED will flash one time to indicate that the Slide Shot Mod has been toggled on/off.
NOTE: You must be either walking or running forward to perform slide shot. If you are standing still you will
perform drop shot.
, then
, then
, then
, then
, then
, then
–
AUTO RUN MOD
The Auto Run Mod allows you to run without pressing in the Left Stick . To use Auto Run, simply use the
Left Stick normally.
To enable/disable Auto Run, Press In & Hold the Left Thumbstick , Tap Up on D-Pad , then Release
the Left Thumbstick . The PS4 Controller LED will flash one time to indicate that the Auto Run Mod has
been toggled on/off.
Note: Certain button presses will temporarily disable Auto Run , ). To quickly re-enable, Press In
on the Left Stick and Release.
DOUBLE TAP MOD
The Double Tap Mod fires your weapon one time when you press the Right Trigger and fires again when you
release the Right Trigger. To enable/disable Double Tap, Hold Down Right Trigger , Tap Right on D-Pad
1x, then Release the Right Trigger . The PS4 Controller LED will flash one time to indicate that the Double
Tap Mod has been toggled on/off.
, then
, then
, then
, then
–
BURST MODE
Burst Mode allows you to set the number of shots fired with each trigger pull. Your GamerModz Juggernaut
Controller comes with 4 Settings for Burst Mode.
To enable Burst Mode - Rapid Fire must first be enabled (See Page 2 “Toggle Between Rapid Fire Modes”) –
Hold Down the Right Trigger and Tap Right on the D-Pad the number of times corresponding to the
Burst Mode below. Then Release the Right Trigger . The PS4 Controller LED will flash the number of times
corresponding to the mode selected, indicating that Burst Mode has been toggled on.
To disable Burst Mode Hold Down the Right Trigger and Tap Right on the D-Pad 6 or more times,
then Release the Right Trigger . The PS4 Controller LED will flash one time to indicate that Burst Mode has
been toggled off.
MODE 2 ----------------- X 2
2 ROUND BURST
MODE 3 ----------------- X 3
3 ROUND BURST
MODE 4 ----------------- X 4
4 ROUND BURST
MODE 5 ----------------- X 5
5 ROUND BURST
TURN OFF -------------- X 6
DISABLE BURST MODE
Notes:
You must have Rapid Fire Enabled to Enable Burst Mode. If Rapid Fire is not Enabled, Enabling Burst
Mode will fail.
Gameplay Tips:
Combine Burst Mode with a Weapon’s Optimal Max Fire Rate to increase accuracy and save on Ammo.
, then
X Mode #, then
–
AUTO AIM MOD
The Auto Aim Mod automatically pulls up your scope when you pull the Right Trigger to fire.
To enable/disable Auto Scope, Hold Down the Left trigger and Right Trigger , then Tap Left on the D-
Pad . Then Release the Left Trigger and Right Trigger . The PS4 Controller LED will flash one
time to indicate that the Auto Aim Mod has been toggled on/off.
AUTO BREATH MOD
The Auto Breath Mod steadies the aim, by automatically holding your breath when you are scoped in with a
sniper rifle.
Note: You can still run out of breath!
To enable/disable Auto Breath, Hold Down the Left trigger and Press In Left Thumbstick , then Tap
Down on the D-Pad . Then Release the Left Trigger and Left Thumbstick . The PS4 Controller
LED will flash one time to indicate that Auto Breath has been toggled on/off.
+
+
, then
, then
+
+
, then
, then
–
QUICK SCOPE MOD – CHOOSING A MODE
The Quick Scope Mod has 5 Programmable Modes. Quick Scope Mod allows the user to time perfectly the
function of scoping in and firing the weapon at the exact moment accuracy is achieved by simply tapping the
Left Trigger .
To enable a Quick Scope Mode, Hold Down on the Left Trigger , then Tap Left on the D-Pad the
number of times corresponding the Mode you would like to select. Then Release the Left Trigger . The
PS4 Controller LED will flash the number of times corresponding to the Mode you have Enabled.
To disable Quick Scope, Hold Down the Left trigger , Tap Right on the D-Pad , then Release the Left
Trigger . The PS4 Controller LED will flash one time to indicate that Quick Scope has been disabled.
MODE 1 ----------------- X 1
CUSTOM
MODE 2 ----------------- X 2
CUSTOM
MODE 3 ----------------- X 3
CUSTOM
MODE 4 ----------------- X 4
CUSTOM
MODE 5 ----------------- X 5
CUSTOM
, then
X Mode #,
then
–
QUICK SCOPE MOD – PROGRAMMING A MODE
The Quick Scope Mod has 5 Programmable Modes.
Once you are in the Mode you wish to Program, Hold Down the Left Trigger and Hold Down Left on D-Pad
until the LED Begins Flashing, then Release the Left Trigger . The PS4 Controller LED will flash 5
times letting you know that you are now in Programming Mode.
Once in Programming Mode you can adjust the timing of the Quick Scope Mod. Please follow the steps below
to optimize the timing for quick scope.
Step 1: Go into a game; choose a load out with the sniper rifle you want to configure and locate a wall in the
game that you can fire at. Be aware that perks that change the weapon ready speed, different scopes, etc. -
will affect optimal timing of the Quick Scope Mod.
Step 2: Enable the Quick Scope Mode you would like to Program (Refer to Page 10 “Quick Scope Mod – Choosing
a Mode”)
Step 3: Enter Programming Mode (See Above)
Step 4: Tap Up on the D-Pad to Increase or Down on the D-Pad to Decrease the time between how
long the scope takes to come up and when the firing happens. After every adjustment you can test the setting
by Tapping the Left Trigger .
What you are looking for when testing is finding the setting where every time you tap the Left Trigger, the scope
comes up, the gun fires and all the rounds hit the same spot on the wall. By default, all 5 Modes are configured
for the L115 in Call of Duty Ghosts with no perks on that affect the timing.
Step 5: Once you have found the ideal setting, Tap Left on the D-Pad and the LED will flash the
corresponding amount of times for that setting. For example, a Setting of 50, will flash the LED 50 times.
Note: To setup a different Quick Scope Mode, simply enter the mode and repeat the programming process
above.
, then
X 1 , then
Until LED
Begins to Flash
–
FAST RELOAD MOD – CHOOSING A MODE
The Fast Reload Mod has 5 Programmable Modes. Fast Reload cuts out the animation time and speeds up the
reloading process.
To enable a Fast Reload Mode, Hold Down on the Square Button , then Tap Up on the D-Pad the
number of times corresponding the Mode you would like to select. Then Release the Square Button . The
PS4 Controller LED will flash the number of times corresponding to the Mode you have enabled.
To disable Fast Reload, Hold Down the Square Button , Tap Down on the D-Pad , then
Release the Square Button . The PS4 Controller LED will flash one time to indicate that Fast
Reload has been disabled.
MODE 1 ----------------- X 1
CUSTOM
MODE 2 ----------------- X 2
CUSTOM
MODE 3 ----------------- X 3
CUSTOM
MODE 4 ----------------- X 4
CUSTOM
MODE 5 ----------------- X 5
CUSTOM
, then
X Mode #,
then
–
FAST RELOAD MOD – PROGRAMMING A MODE
The Fast Reload Mod has 5 Programmable Modes. Note: Start around a setting of 22 and go from there!
Once you are in the Mode you wish to Program, Hold Down the Square Button and Hold Down Up on D-
Pad until the PS4 LED begins to flash, then Release the Square Button . The PS4 Controller LED will
flash 5 times letting you know that you are now in Programming Mode.
Once in Programming Mode you can adjust the timing of the Fast Reload Mod. Please follow the steps below to
optimize the timing for Fast Reload.
Step 1: Go into a game; choose a load out with the weapon you want to configure Fast Reload for. Be aware
that perks like slight-of-hand cannot be used with the Fast Reload Mod.
Step 2: Choose the Fast Reload Mode you would like to Program (Refer to Page 12 “Fast Reload Mod – Choosing
a Mode”)
Step 3: Enter Programming Mode (See Above)
Step 4: Tap Up on the D-Pad to Increase or Down on the D-Pad to Decrease the time to optimize
Fast Reload timing. After every adjustment you can test the setting it by Tapping the Square Button .
The way Fast Reload works is by eliminating animation time. You are trying to set Fast Reload timing at the
point where he puts the clip in, the swap weapons glitch happens and your clip ends up fully loaded without
waiting for the extra animation of the reload. Increase the speed (Up on D-Pad ) and keep testing until the
full reload does not happen. Then decrease the speed (Down on D-Pad ) until it's fully reloading your clip
again. This will bring you to the fastest possible speed for the mod. Remember, every weapon is different so
there is no "one size fits all” setting.
By default, all 5 Modes of Fast Reload are configured for the SVU in Call of Duty Ghosts with no perks on that
affect the timing.
Step 5: Once you have found the ideal setting, Tap Right on D-Pad to save the setting and the LED will flash
the corresponding amount of times for that setting. For example, a Setting of 22, will flash the LED 22 times.
Note: To setup a different Fast Reload Mode, simply enter the mode and repeat the programming process
above.
, then
, then
Until LED
Begins to Flash
–
Quick reference Guide
Below is a quick reference chart showing what mods work with each other as well as some additional
information on the functionality of your GamerModz Juggernaut controller.
Rapid
Fire
Left
Trigger
Rapid
Fire
Dual
Trigger
Rapid
Fire
Jitter
Slide
Shot
Drop
Shot
Auto
Drop
Max
Boost
Shot
Boost
Shot
Jump
Shot
Auto
Run
Double
Tap
Auto
Burst
Auto
Aim
Auto
Breath
Quick
Scope
Fast
Reload
Rapid
Fire
Left
Trigger
Rapid
Fire
Dual
Trigger
Rapid
Fire
Jitter
Slide
Shot
Drop
Shot
Auto
Drop
Max
Boost
Shot
Boost
Shot
Jump
Shot
Auto
Run
Double
Tap
Auto
Burst
Auto
Aim
Auto
Breath
Quick
Scope
Fast
Reload
–
ZOMBIE MODE
The Juggernaut 5.1 comes with a new mode called Zombie Mode (Mode 2). Zombie Mode is beneficial on Single
Player Zombie where Auto Aim can be utilized.
Zombie Mode has the following Mods:
Auto Run (Ref. Page 9)
Rapid Fire with Auto Aim
To change to Zombie mode, hold down the Left Thumbstick and tap Right on the D-Pad 2 times, then
release the Left Thumbstick . The LED will flash 2 times corresponding to the mode selected.
ENABLE/DISABLE RAPID FIRE WITH AUTO AIM
To enable/disable Rapid Fire with Auto Aim, Hold Down the Right Trigger , Tap Down on D-Pad ,
then Release the Right Trigger . The PS4 Controller LED will flash one time to indicate that the Rapid Fire
with Auto Aim has been toggled on/off.
, then
, then
, then
2x, then
–
TOGGLING BETWEEN L1/R1 AND L2/R2
Your GamerModz Controller is set up where you can choose to use the default layout of L2/R2 as your primary
buttons or Flip the layout to L1/R1 to Zoom and Shoot.
To change modes, hold down the Left Thumbstick and hold down Down on the D-Pad until the main
LED flashes. The LED flashing indicates that the layout was changed for the mods.
IMPORTANT: Your GamerModz controller comes default as L2/R2 as primary. If you would like to flip the
layout to L1/R1 you must follow the instructions below as well as flip your layout in the controller layout
options of the console.
***If you flip mode to L1/R1 all instructions that call for R2/L2 will need to be replaced
with R1/L1, respectively.
, then
, then
–
INSTRUCTION MANUAL
LED PRO BUTTONS FOR PS4
(OPTIONAL ACCESSORY)
The GamerModz LED Pro Buttons allows you to remap the following buttons to either of the Pro Buttons:
A, B, X, Y, LB, RB, LT, RT, L3, R3, D-Pad Up, D-Pad Down, D-pad Left, D-Pad Right
NOTE: Guide Button, Menu Button and View Button Cannot be Remapped
Additionally, you we have given you the ability to have 5 Modes (Profiles) allowing you program 5 different
scenarios. The controller will save the profiles for you, even when you turn the controller off. You can change
any of the profiles at any time using the instruction below.
CYCLING THROUGH PRESETS
To cycle through the Presets hold the Left Thumbstick and Tap Left on the D-Pad the number of
times corresponding to the mode/preset you want. The Main LED will flash the number of times corresponding
to the mode/preset chosen. Additionally, if presets 1-5 are chosen, the LED Pro Mods will Light Up.
TAP UP ON D-PAD
PRESET
1 TIME
PRESET 1
2 TIMES
PRESET 2
3 TIMES
PRESET 3
4 TIMES
PRESET 4
5 TIMES
PRESET 5
6 TIMES
OFF
, X Times
, then
Page is loading ...
Page is loading ...
/
