Fantech FQ110 Instructions Manual

Brand: Fantech

Model: FQ110

Category: Household fans

Type: Instructions Manual

This manual is also suitable for

FQ Series

Quiet Exhaust Fans

and Fan-Lights

1. Use this unit in the manner intended by the manufacturer. If you have

any questions, please contact the manufacturer .

2. Before servicing or cleaning unit, switch power off at service panel

and lock the service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction.

4. Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fuel burning equipment to pre-

vent back drafting. Follow the heating equipment manufacturer’s

guideline and safety standards such as those published by the

National Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

5. When cutting or drilling into wall or ceiling, do not damage electrical

wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it must be marked

as appropriate for the application and be connected to a GFCI

(Ground Fault Circuit Interrupter) – protected branch circuit.

8. NEVER place a switch where it can be reached from a tub or shower.

9. This fan must be properly grounded.

10. Do not use in the cooking area (Figure. 1).

Floor

Cooking

Equipment

Cooking area

Do not install above

or inside this area

Figure 1

11. Do not block the air intakes or exhaust.

12. Power supply wiring is to be No. 14 AWG wire or larger (suitable

for at least 90°C (190°F) ).

13. Not for use outdoors.

14. For lighted units, use only CFL type T4, 26W lamp and a maxi-

mum 4 W night light .

15. The fan must not be installed in a ceiling with an “R” rating

greater than 40.

16. The fan is type IC (Inherently Protected).

17. To reduce the risk of injury, install the fan at least 7 feet (2.1m)

above the floor.

18. Acceptable for use over a shower or tub when installed in a GFCI

protected branch circuit.

19. The fan should not be turned on or off rapidly.

20. Do not clean the fan with corrosive chemicals or water in excess of

60° C (140° F).

21. If the fan is not operating properly, shut the power off immediately,

and have a certified installer inspect it and have it serviced as

required.

22. These fan must be mounted to structural members that are strong

enough to support the fan’s weight.

23. Do not allow foreign objects to enter the fan; this could result in

electric shock or fan damage.

READ AND SAVE THESE INSTRUCTIONS!

Read carefully all instructions before installing or using this product

FQ Series Fan

FQ Series Fan-Lights

Package Includes:

1 Fantech Exhaust Fan or Fan-Light

5 Mounting Brackets

8 Mounting screws

1 26W CFL Type T4 (Fan-Light models only)

1 4w night light (Fan-Light Models only)

WARNINGS: BEFORE INSTALLATION, TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

CAUTION:

1. For general ventilating use only. Do not use to exhaust haz-

ardous or explosive materials and vapors.

2. This product is designed for installation in flat ceilings only.

Do not install it in a sloping ceiling or in a wall.

3. To avoid motor bearing damage and noisy unbalanced impel-

lers keep construction material / dust from entering the fan.

4. Please read specification label on the product for further

information and requirements.

Installation

The unit should only be installed in a ceiling. The size of joists should be at least

2” wide and 4” high . The space between two joists should be 16”. From the above

surface of the suspended ceiling there should be minimum 9” distance to the roof.

(Figure 2) Select the suspension brackets as shown in (Figure 3)

Power supply

protective tube

Housing

Fan outlet

Ceiling joist

Ceiling

Wire box

Wire box cover

Hanger bar

Spacing A on center joist Insert Suspension bracket

16 inches Figure 3-1

24 inches Figure 3-2

Joists

Plug-in

Figure 3

1. Remove the grille by gently squeezing the wire springs and extracting

them from the slots in the housing.

2. Remove the wire box cover and install the 3 brackets on the fan housing.

(Figure. 3-1, Figure. 3-2).

Figure 3-1

Figure 3-2

3. To install the housing in the ceiling, position it between the joists and

extend the brackets to the adjacent joists.. Mark the screw locations (at

the top of the keyhole on each bracket) on the joists.

NOTE:

The bottom edge of the housing should be flush with the bottom of the joist.

(Figure 4)

4. Remove the housing and drive the screws part way into the joists at the

marked locations. (Figure 5)

Power supply

protective tube

Housing

Fan outlet

Ceiling joist

Ceiling

Wire box

Wire box cover

Hanger bar

Spacing A on center joist Insert Suspension bracket

16 inches Figure 3-1

24 inches Figure 3-2

Joists

Plug-in

Figure 5

Power supply

protective tube

Housing

Fan outlet

Ceiling joist

Ceiling

Wire box

Wire box cover

Hanger bar

Spacing A on center joist Insert Suspension bracket

16 inches Figure 3-1

24 inches Figure 3-2

Joists

Plug-in

Figure 6

5. Mount the housing using the screws in the joists and then secure them

tightly. Make all the electrical connections in the wire box, per the wiring

diagram, and attach the wire box cover. Attach the discharge duct tightly

onto the fan outlet.

NOTE:

In order for the fan to operate efficiently, keep the discharge duct as

straight as possible. (Figure 6)

6. To complete the installation, install the lamps (if applicable) and mount the grille.

Power supply

protective tube

Housing

Fan outlet

Ceiling joist

Ceiling

Wire box

Wire box cover

Hanger bar

Spacing A on center joist Insert Suspension bracket

16 inches Figure 3-1

24 inches Figure 3-2

Joists

Plug-in

Figure 4

Power supply

protective tube

Housing

Fan outlet

Ceiling joist

Ceiling

Wire box

Wire box cover

Hanger bar

Spacing A on center joist Insert Suspension bracket

16 inches Figure 3-1

24 inches Figure 3-2

Joists

Plug-in

Figure 2

Wiring Diagram

Maintenance

1. Turn the power off and lock it out prior to servicing or cleaning.

2. To clean the grille, first remove it from the fan then use a soft brush and

clean water to remove the dirt. If the dirt is not easily removed, wash with

a neutral detergent.

3. In order to remove the impeller and housing for maintenance, first remove

the light, night light and reflector (if applicable). Then unplug the electrical

connection and remove the 4 screws that secure the fan assembly to the

housing. To clean the impeller and housing, remove the motor and then wash

with water or a neutral detergent, as required.

NOTE:

Keep all electrical components away from water. Do not use corrosive chemi-

cals or water in excess of 60C (140°F) to clean plastic parts.

For Fan-Light Combination For Fan Only Units

Fan Speciﬁcations

Model

Power Consumption (W)

Airﬂow (CFM)

Power Motor Light (CFL) Night Light

FQ80 120V/60 Hz 25 – – 80

FQ110 120V/60 Hz 30 – – 110

FQ80FL 120V/60 Hz 25 26W 4W 80

FQ110FL 120V/60 Hz 30 26W 4W 110

Specifications

Power supply

protective tube

Housing

Fan outlet

Ceiling joist

Ceiling

Wire box

Wire box cover

Hanger bar

Spacing A on center joist Insert Suspension bracket

16 inches Figure 3-1

24 inches Figure 3-2

Joists

Plug-in

Figure 7

11 7/8''

9 1/2''

3 3/8''

9 1/2''

11''

3 7/8''

8 1/2''

4''

Dimensions

Five (5) Year Warranty

Limitation of Warranty and Liability

Warning

DURING ENTIRE WARRANTY PERIOD:

FANTECH will repair or replace any part which has a factory defect in workman-

ship or material. Product may need to be returned to the Fantech factory, togeth-

er with a copy of the bill of sale and identified with RMA number.

FOR FACTORY RETURN YOU MUST:

• Have a Return Materials Authorization (RMA) number. This may be obtained by

calling FANTECH either in the USA at 1.800.747.1762 or in CANADA at

1.800.565.3548. Please have bill of sale available.

• The RMA number must be clearly written on the outside of the carton, or the

carton will be refused.

• All parts and/or product will be repaired/replaced and shipped back to buyer; no

credit will be issued.

THE FOLLOWING WARRANTIES DO NOT APPLY:

• Damages from shipping, either concealed or visible. Claim must be filed

with freight company.

• Damages resulting from improper wiring or installation.

• Damages or failure caused by acts of God, or resulting from improper

consumer procedures, such as:

1. Improper maintenance

2. Misuse, abuse, abnormal use, or accident, and

3. Incorrect electrical voltage or current.

• Removal or any alteration made on the FANTECH label control number

or date of manufacture.

• Any other warranty, expressed, implied or written, and to any consequential or

incidental damages, loss or property, revenues, or profit, or costs of removal,

installation or reinstallation, for any breach of warranty.

WARRANTY VALIDATION

• The user must keep a copy of the bill of sale to verify purchase date.

• These warranties give you specific legal rights, and are subject to an applicable

consumer protection legislation. You may have additional rights which vary from state

to state.

Fantech, reserves the right to modify, at any time and without notice, any or all

of its products’ features, designs, components and specifications to maintain

their technological leadership position.

Item #: 483431

Rev Date:

062711

United States

10048 Industrial Blvd.

Lenexa, KS 66215

Phone: 800.747.1762; 913.752.6000

Fax: 800.487.9915; 913.752.6466

www.fantech.net; [email protected]

Canada

50 Kanalflakt Way,

Bouctouche, NB E4S 3M5

Phone: 800.565.3548; 506.743.9500

Fax: 877.747.8116; 506.743.9600

www.fantech.net; [email protected]

This warranty does not apply to any FANTECH INC. product or part which has failed as a result of faulty installation or abuse, incorrect electrical

connections or alterations made by others, or use under abnormal operating conditions or misapplication of the product or parts. We will not

approve for payment any repair not made by us or our authorized agent without prior written consent. The foregoing shall constitute our sole and

exclusive warranty and our sole exclusive liability, and is in lieu of any other warranties, whether written, oral, implied or statutory. There are no

warranties which extend beyond the description on the page hereof. In no event, whether as a result of breach of contract, or warranty or alleged

negligence, defect incorrect advice or other causes, shall FANTECH be liable for special or consequential damages, including, but not limited to,

loss of profits or revenue, loss of use of equipment or any other associated equipment, cost of capital, cost of substitute equipment, facilities or

services, downtime costs, or claims of customers of purchase for such damages. FANTECH neither assumes or authorizes any person to assume

for it any other liability in connection with the sale of product(s) or part(s). Some jurisdictions do not allow the exclusion or limitation of incidental

or consequential damages so the above limitations and exclusions may not apply to you.

FANTECH, INC. products are designed and manufactured to provide reliable performance, but they are not guaranteed to be 100% free from defects. Even reliable

products will experience occasional failures and this possibility should be recognized by the user. If these products are used in a life support ventilation system where

failure could result in loss or injury, the user should provide adequate backup ventilation, supplementary natural ventilation, failure alarm system, or acknowledge

willingness to accept the risk of such loss or injury.

Page is loading ...