Exerpeutic 1220.2 Owner's manual

Brand: Exerpeutic

Model: 1220.2

Type: Owner's manual

OWNER’SMANUAL

INDOORTRAININGBIKE

IMPORTANT: Read all instructions carefully before using this product. Retain

this owner’s manual for future reference.

The specifications of this product may vary from this photo, subject to change

without notice.

1220.2‐050916



SERVICE ------------------------------------------------------------------------ 2

LABEL PLACEMENT --------------------------------------------------------- 3

PRODUCT SAFETY ---------------------------------------------------------- 4

OVERVIEW DRAWING ------------------------------------------------------ 5

PARTS LIST --------------------------------------------------------------------- 6

HARDWARE & TOOLS PACK---------------------------------------------- 7

ASSEMBLY --------------------------------------------------------------------- 8

COMPUTER --------------------------------------------------------------------- 15

ADJUSTMENTS ---------------------------------------------------------------- 16

EMERGENCY STOP ---------------------------------------------------------- 18

MOVING THE BIKE ----------------------------------------------------------- 19

TROUBLE SHOOTING & MAINTENANCE ----------------------------- 20

WARRANTY -------------------------------------------------------------------- 21

PART REQUEST FORM ----------------------------------------------------- 22

TABLEOFCONTENTS

IMPORTANT: FOR NORTH AMERICA ONLY

For damaged or defective product, questions, replacement parts or any

other service support, please contact our customer service department

(8:00 AM - 5:00 PM Pacific Standard Time, Daily) by the below methods:

For Best Service, please Email:

Service@paradigmhw.com

Response Time: 1-2 Business Days

Website:

www.paradigmhw.com

Toll-Free:

1-844-641-7921

Response time may vary.

Please have the following information ready when requesting for service:

Your name

Phone number

Model number

Serial number

Part number

Proof of Purchase

For damaged or defective product please contact our customer service

before returning to the store.

Paradigm Health & Wellness, Inc.

1189 Jellick Ave.

City of Industry, CA 91748, USA

SERVICE

LABELPLACEMENT

Basic precautions should always be followed when using this equipment.

Read all instructions before using this equipment which include the

following safety instructions:

1. Read all the instructions in this manual and do warm up exercises before

using this equipment.

2. Before exercising, and in order to avoid injuring your muscles, it is

recommended that you perform warm-up exercises for every muscle

group.

3. Make sure all the components are not damaged and tightened well

before use. This equipment should be placed on a flat surface when

using. Using a mat or other covering material on the ground is

recommended.

4. Wear proper clothes and shoes when using this equipment; do not

wear clothes that might get caught by any part of the equipment;

remember to tighten the pedaling straps.

5. Do not attempt any maintenance or adjustments other than those

described in this manual. Should any problems arise, discontinue use

and consult customer service.

6. Do not use or leave the equipment outdoors.

7. This equipment is for household use only.

8. Only one person should be on the equipment while in use.

9. Keep children and pets away from the equipment while in use. This

machine is designed for adults only. This product requires a minimum of

6 square feet of space for safe operation.

10. If you feel any chest pains, nausea, dizziness, or shortness of breath, you

should stop exercising immediately and consult your physician before

continuing.

11. The maximum weight capacity for this product is 300 lbs/136 kgs.

WARNING: Before beginning any exercise program consult

your physician. This is especially important for the people who are

over 35 years old or who have pre-existing health problems. Read all

instructions before using any fitness equipment.

CAUTION: Read all instructions carefully before operating this

product. Retain this Owner’s Manual for future reference.

PRODUCTSAFETY

OVERVIEWDRAWING

No. Description Qty

1 Main Frame 1

2 Front Stabilizer 1

3 Rear Stabilizer 1

4 Seat Post 1

5 Seat Slide Tube 1

6 Handlebar Post 1

7 Hand Pulse Handlebar 1

8 Handlebar 1

14 Right Pedal 1

15 Left Pedal 1

19 Adjustable leveler M12*30 4

20 Carriage Bolt M8*75 4

21 Curved Washer φ8*φ16*1.5 4

22 Cap Nut M8 4

37 Round Knob M16*1.5*18 3

41 Seat DD-6619 1

66 Lock Knob M16*1.5*20 1

75 Console 1

76 Hex Bolt M8*20 4

77 Spring Washer φ8 10

78 Flat Washer Ф8*Ф16*1.5 4

79 Console Bracket 64*60*δ2.5 1

80 Chain 1

84 Hex Bolt M8*45 2

87 Sensor Wire L=700 MM 1

88 Hand Pulse Sensor Wire L=750MM 1

89 Lock Nut M8 S13 2

90 Big Curved Washer Ф8*Ф20*2 2

PARTSLIST

HARDWARE&TOOLSPACK

(20) Carriage Bolt M8x75 4PCS

(21) Curve Washer φ8xφ16x1.5 4PCS

(77) Spring Washer φ8 4PCS

(22) Cap Nut M8 4PCS

(84) Hex Bolt M8x45 2PCS

(90) Big Curve Washer φ8xφ20x2 2PCS

(77) Spring Washer φ8 2PCS

(76) Hex Bolt M8x20 2PCS

(78) Flat Washer φ8xφ16x1.5 2PCS

(77) Spring Washer φ8 2PCS

(89) Lock Nut M8 2PCS

13, 15mm Double Open-Ended Wrench 2PCS

(76) Hex Bolt M8x20 2PCS

(78) Flat Washer φ8xφ16x1.5 2PCS

(77) Spring Washer φ8 2PCS

6mm Allen Wrench 1PCS

Step 6

1 petS

Step 7

Att

ach four Adjustable Levelers (19) onto the Front and Rear Stabilizer (2/3) as shown in

Fig. AA-1.

Front and Rear Stabilizer Inst

allation

Remove the Metal Protective Tube and all hardware. This will not be used in installation

and should be discarded.

Lift up the Front of the Mainframe (1) and align the holes of the Front Stabilizer (2)

with

the

holes on the front bracket. Install the Front Stabilizer (2) using two Carriage Bolts

(20),

two

Curved Washers (21) two Spring Washers (77) and two Cap Nuts (22). Then tighten the

Cap Nuts (22) using the 13, 15mm Double Open Ended Wrench provided.

Lift up the Rear of the Mainframe (1) and align the holes of the Rear Stabilizer (3)

with

the

holes on the rear bracket. Install the Rear Stabilizer (3) using two Carriage Bolts (20), two

Curved Washers (21) two Spring Washers (77) and two Cap Nuts (22). Then tighten the Ca

Nuts (2

2) using the 13, 15mm Double Open Ended Wrench provided.

ASSEMBLY

Hardware:

No. 20 Carriage Bolt

4 PCS

No. 21 Curved Washer

4PCS

No. 22 Cap Nut

4 PCS

No. 77 Spring Washer

4PCS

Tool:

13, 15mm Double Open

Ended Wrench

2PCS

2. Foot

Pedal Installati

Insert the treaded shaft of the Left Pedal (15) into the threaded hole on the left

side of

the

crank. Turn the pedal shaft by hand in a counter-clockwise direction until snug.

DO NOT turn the LEFT pedal shaft in a clockwise direction. Doing so will damage the

threads.

Tighten the pedal shaft of the Left Pedal (15) using the 13, 15mm Double Open Ended

Wrench provided

Insert the treaded shaft of the Right Pedal (14) into the threaded hole on the right side

the

crank. Turn the pedal shaft by hand in a clockwise direction until snug.

DO NOT turn the RIGHT pedal shaft in a counter-clockwise direction. Doing so will

damage the threads.

Tighten the pedal shaft of the Right Pedal (14) using the 13, 15mm Double Open Ended

Wrench provided

Important:

Screw the Right Foot Pedal

(14) into the right crank

clock

se!

Screw the Left Foot Pedal

(15) into the Left crank

ASSEMBLY

The Cranks, Pedal Straps,

Pedal Shafts, and Foot

Pedals are marked “R” for

Right and “L” for Left.

Tool:

13, 15mm Double Open

Ended Wrench

Tool:

13, 15mm Double Open

Ended Wrench

Seat Post Installati

Turn the Round Knob (37) on the Main Frame (1) in a counterclockwise direction until it can be pulled

out. Pull out the Round Knob (37) and slide the Seat Post (4) into the slot on the back of the Mainframe (1).

Lock the Seat Post (4) in place by releasing the Round Knob (37) and sliding the Seat Post (4) up or down

slightly until the Round Knob (37) "pops" into the locked position. Tighten the Round Knob (37) in a

clockwise direction.

NOTE: When adjusting the height of seat post, the MAX line cannot be higher than

the edge of plastic bushing.

Seat Cushion and Seat Slide Tube Installation

a. Install the Seat Cushion (41) onto the Seat Slide Tube (5) and tighten using the two 13, 15mm

Doubl

e Open Ended Wrenches provided as shown in Fig. AA-2.

b. Insert the Seat S

liding Tube (5) into the Seat Post (4), and a

ttach the Round Knob (37) onto

the

tube of the Seat Post (4) by tuning it in a clockwise direction.

ASSEMBLY

5. Ha

ndlebar Post Inst

allation

a. Insert the Handlebar Post (6) into the tube of the Main Frame (1). Attach the Round Knob (10)

onto the tube of the Main Frame (1) by turning it in a clockwise direction.

b. T

o adjust the position of the Handlebar Post (6), loosen the Round Kn

ob (37) by turning it

coun

ter-clockwise. Slide the Handlebar Post (6) up or down to the desired position and tighten the

knob by turning clockwise. Ensure that the Round Knob (37) has “popped” into one of the holes in

the Handlebar Post (6).

NOTE: When adjusting the height of handlebar post, the MAX line cannot be higher

than the edge of plastic bushing.

c. Finally, attach the Lock Knob (66) onto the tube of the Main Frame (1) by turning it in a

ockwise direction until firm and secure.

ASSEMBLY

Tool:

13, 15mm Double Open

Ended Wrench

6. Handlebar Installation

Attach the Handlebar (8) onto the Hand Pulse Handlebar (7) using two Big Curve

Washers (90), two Spring Washers (77), and two Hex Bolts (84). Tighten bolts with the 6mm

Allen Wrench provided.

ASSEMBLY

Tool:

6mm Allen Wrench

Hardware:

No. 90 Big Curve Washer

2PCS

No. 77 Spring Washer

2PCS

No. 84 Hex Bolt

2PCS

7. Hand Pulse Handlebar and Computer Bracket Installation

Attach the Computer Bracket (7) and Hand Pulse Handlebar (7) onto the

Handlebar Post (2) using four Hex Bolts (76), four Spring Washers (78), four Flat

Washers (77) and two Lock Nuts (89). Tighten the Bolts and Nuts using the 6mm Allen

Wrench and 13, 15mm Double Open-Ended Wrench provided.

ASSEMBLY

Tool:

6mm Allen Wrench

13, 15mm Double Open

Ended Wrench

Hardware:

No. 78 Spring Washer

4 PCS

No. 77 Flat Washer

4 PCS

No. 89 Lock Nut

2 PCS

No. 76 Hex Bolt

4 PCS

8. Connecting the Wires

a. Attach the Console (75) onto the Console Bracket (79).

b. Connect the Sensor Wire (87) to the wire that comes from the Console (75) as

shown in Fig. AA-3. Plug the Hand Pulse Sensor Wire (88) into the receptacle located

on the back of the Console (8).

ASSEMBLY

USING YOUR COMPUTER

The computer can be activated by pressing the “MODE” button or by pedaling. If

you leave the computer idle for 4 minutes, the power will shut off automatically.

BUTTON FUNCTIONS:

MODE: Press the MODE button to navigate through each function of the computer.

Press and hold the MODE button for 4 seconds to reset all data values to zero.

COMPUTER FUNCTIONS:

SCAN: Press the MODE button until the “◄” points to SCAN, the computer will

automatically scan each function in sequence and change every 4 seconds.

TIME: Press the MODE button until the “◄” points to TIME, the computer will display

your elapsed workout time in minutes and seconds.

SPEED: Press the MODE button until the “►” points to SPEED, the computer will

display the current training speed.

DIST (DISTANCE): Press the MODE button until the “►” points to DIST (DISTANCE),

the computer will display the accumulative distance traveled during workout.

CAL (CALORIES): Press the MODE button until the “►” points to CAL (CALORIES),

the computer will display the total accumulated calories burned during workout.

RPM: Press the MODE button until the “►” points to RPM, the computer will display

the revolutions per minute.

PULSE: Press the MODE button until the “◄” points to PULSE, the computer will

display the users heart rate while gripping the handlebar sensors during exercise. To

ensure the pulse readout is more precise, always hold on to the handlebar grip sensors

with two hands instead of just with one.

COMPUTER

Brake Knob

Adjustable Leveler

HOW TO INSTALL THE BATTERIES:

1. Remove the battery cover on the back of the computer.

2. Place two "SIZE-AA" batteries into the battery housing.

3. Ensure that the batteries are correctly positioned and that the battery springs are in

proper contact with the batteries.

4. Re-install the battery cover.

5. If the display is illegible or only partial segments appear, remove the batteries and

wait 15 seconds before reinstalling.

ADJUSTMENTS

Adjusting the Adjustable Leveler

Turn the Adjustable Leveler on the front and rear stabilizers as needed to level the bike.

Adjusting the Brake Knob

To increase the resistance, turn the Brake Knob in a clockwise direction.

To decrease the resistance, turn the Brake Knob in a counter-clockwise direction.

ADJUSTMENTS

Round Knob

Lock Knob

Adjusting the Handlebar Height

Loosen the Lock Knob and then loosen the Round Knob by turning in a

counter-clockwise direction until it can be pulled out. Pull out the Round Knob and then

slide the Handlebar Post up or down to a suitable position. Lock the Handlebar Post in

place by releasing the Round Knob and sliding the Handlebar Post up or down slightly

until the Round Knob "pops" down into the locked position. Then tighten both Lock Knob

and Round Knob in a clockwise direction.

NOTE: When adjusting the height of handlebar post, the MAX line cannot higher

than the edge of plastic bushing.

Adjusting the Seat Height

Loosen the Round Knob by turning in a counter-clockwise direction until it can be

pulled out. Pull out the Round Knob and slide the Seat Post up or down to a suitable

position. Lock the Seat Post in place by releasing the Round Knob and sliding the Seat

Post up or down slightly until the Round Knob "pops" down into the locked position. Then

tighten the Round Knob in a clockwise direction.

NOTE: When adjusting the height of seat post, the MAX line cannot higher than

the edge of plastic bushing.

ADJUSTMENTS

Round Knob

Adjusting the Seat Forward or Back

Loosen the Round Knob by turning it in a counter-clockwise direction. Slide the

Seat Sliding Tube in a forward or backwards to a suitable position. Lock the Seat Sliding

Tube in place by turning it in a clockwise direction.

EMERGENCY STOP

To emergency stop, press firmly down onto the BRAKE KNOB. Continue holding the

BRAKE KNOB down until the flywheel comes to a complete stop

Round Knob

EMERGENCYSTOP

Page is loading ...

Exerpeutic 1220.2 Owner's manual

Exerpeutic 1220.2 Owner's manual

Exerpeutic 1220.2 Owner's manual

Related papers

Other documents