Page is loading ...
Tomcat i875PR S5102-P User’s Manual
///
Tomcat i875PR S5102-P
Revision 1.00
Copyright © TYAN Computer Corporation, 2005. All rights reserved. No part of this manual
may be reproduced or translated without prior written consent from TYAN Computer Corp.
All registered and unregistered trademarks and company names contained in this manual are
property of their respective owners including, but not limited to the following.
TYAN, Tomcat, i875PR and S5102-P are trademarks of TYAN Computer Corporation.
Intel, Pentium 4, and combinations thereof are trademarks of Intel Corporation.
Promise is a trademark of Promise Technology, Inc.
Award, AwardBIOS are trademarks of Award Software Incorporated.
Microsoft and Windows are trademarks of Microsoft Corporation.
IBM, PC, AT and PS/2 are trademarks of IBM Corporation.
ATI, ATI RAGE is a trademark of ATI Technologies Incorporated.
Winbond is a trademark of Winbond Electronics Corporation.
Analog Devices is a trademark of Analog Devices, Inc.
Portable Document Format (PDF) is a trademark of Adobe Corporation.
Information contained in this document is furnished by TYAN Computer Corporation and has
been reviewed for accuracy and reliability prior to printing. TYAN assumes no liability
whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of
TYAN products including liability or warranties relating to fitness for a particular purpose or
merchantability. TYAN retains the right to make changes to product descriptions and/or
specifications at any time, without notice. In no event will TYAN be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting
from errors or inaccuracies of information contained in this document.
i
http://www.tyan.com
Tomcat i875PR S5102-P Table of Contents
Table of Contents
Before you begin… .................................................................................................................iv
Chapter 1: Introduction.........................................................................................................1-1
1.1 – Congratulations!...................................................................................................... 1-1
1.2 – Hardware Specifications ......................................................................................... 1-1
Chapter 2: Board Installation...............................................................................................2-1
2.1 – Board Image ........................................................................................................... 2-2
2.2 – Board Parts ............................................................................................................. 2-3
2.3 – Block Diagram......................................................................................................... 2-4
2.4 – Jumper Settings & Definitions................................................................................. 2-5
2.5 – Connector Description ............................................................................................ 2-6
2.6 – Mounting the Motherboard .................................................................................... 2-12
2.7 – Installing the Memory............................................................................................ 2-13
2.8 – Memory Installation Procedure ............................................................................. 2-14
2.9 – Installing the Processor and Heatsink................................................................... 2-15
2.10 – Attaching Drive Cables ....................................................................................... 2-17
2.11 – Installing Add-In Cards........................................................................................ 2-19
2.12 – Connecting External Devices.............................................................................. 2-20
2.13 – Installing the Power Supply................................................................................. 2-22
2.14 – Finishing Up ........................................................................................................ 2-22
Chapter 3: BIOS Setup..........................................................................................................3-1
3.1 – Main BIOS Setup .................................................................................................... 3-2
3.2 – Standard CMOS Features ...................................................................................... 3-4
3.3 – Advanced BIOS Features ....................................................................................... 3-5
3.4 – Advanced Chipsets Features.................................................................................. 3-9
3.5 – Integrated Peripherals........................................................................................... 3-10
3.6 – Power Management Setup ................................................................................... 3-14
3.7 – PnP/PCI Configurations ........................................................................................ 3-17
3.8 – PC Health Status .................................................................................................. 3-18
3.9 – Frequency/Voltage Control ................................................................................... 3-19
3.10 – Load Fail-Safe Defaults ...................................................................................... 3-20
3.11 – Load Optimized Defaults..................................................................................... 3-20
3.12 – Supervisor/User Password Setting ..................................................................... 3-21
3.13 – Exit Selecting ...................................................................................................... 3-22
Chapter 4: SATA/RAID Setup (for SATA RAID model) ......................................................4-1
4.1 – Getting Started ........................................................................................................ 4-1
4.2 – Creating Your Disk Array ........................................................................................ 4-2
Creating an Array for Performance........................................................................... 4-4
Creating a Security Array with New Drives............................................................... 4-4
Creating a Security Array with an Existing Data Drive.............................................. 4-5
4.3 – Installing Software Drivers ...................................................................................... 4-6
New Windows 2000/XP Installation .......................................................................... 4-6
Existing Windows 2000/XP Installation..................................................................... 4-6
Confirming Windows 2000/XP Installation................................................................ 4-6
New Windows 98/Me Installation.............................................................................. 4-7
Existing Windows 98/Me Installation ........................................................................ 4-7
New Windows NT 4.0 Installation ............................................................................. 4-8
Existing Windows NT 4.0 Installation........................................................................ 4-8
4.4 – Using FastBuild™ Configuration Utility ................................................................... 4-9
Viewing PDC20378 BIOS Screen............................................................................. 4-9
Navigating the FastBuild™ Setup Menu................................................................. 4-10
Creating Arrays Automatically ................................................................................ 4-11
Optimize Array For.................................................................................................. 4-11
ii
http://www.tyan.com
Tomcat i875PR S5102-P Table of Contents
Viewing Drive Assignments .................................................................................... 4-12
Deleting An Array.................................................................................................... 4-12
Rebuilding A Mirrored Array.................................................................................... 4-14
Chapter 5: Diagnostics.........................................................................................................5-1
5.1 – Beep Codes ............................................................................................................ 5-1
5.2 – Flash Utility.............................................................................................................. 5-1
Appendix I: Glossary ............................................................................................................6-1
Appendix II: Post Error Code for BIOS ...............................................................................6-7
Appendix III: SMDC Information ........................................................................................6-12
Technical Support .......................................................................................................... 6-13
iii
http://www.tyan.com
Tomcat i875PR S5102-P Before you begin…
Before you begin…
Check the box contents!
The retail motherboard package should contain the following:
1x Tomcat i875PR S5102-P motherboard
1x 34-Pin floppy drive cable
1x Ultra-DMA-133/100/66/33 IDE cable
1x Ultra-DMA-133/100/66/33 IDE cable
1x Tomcat i875PR S5102-P User’s Manual
1x Tomcat i875PR S5102-P Quick Reference Guide
1x TYAN driver CD
1x I/O shield
1 x Promise FastTrak 378 RAID Driver Diskette
1 x Cable set: 9-pin Serial and 25-pin Parallel
2 x Serial ATA power cable
4 x Serial ATA cable
1 x USB2.0 cable
If any of these items are missing, please contact your vendor/dealer for replacement before
continuing with the installation process.
iv
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 1: Introduction
Chapter 1: Introduction
1.1 – Congratulations!
You have purchased one of the most powerful solutions for the Intel Pentium
®
4 processor, the
Tomcat i875PR S5102-P Based on Intel 875P chipset, this platform offers convenient remote
Intelligent Platform Management Interface (IPMI) monitoring through a Server Management
Daughter Card. The Tomcat i875PR S5102-P are ATX form factor, onboard Gigabit Ethernet
port, Fast Ethernet port, Serial ATA, IDE RAID and an onboard ATI 8MB PCI RAGE XL VGA.
Remember to visit TYAN’s Website at
http://www.tyan.com. There you can find information on
all of TYAN’s products with FAQs, distributors list, and BIOS setting explanations.
1.2 – Hardware Specifications
Processors
• Socket 478 processor
• Supports single Intel
®
Pentium
®
4 processor
“Northwood / Prescott”
• Onboard VRM10
• Front-Side Bus support for 800/533/400MHz
Chipset
• Intel
®
875P North Bridge chipset
• Intel
®
ICH5 South Bridge chipset
• Winbond
®
W83627HF LPC I/O chip
• Analog devices ADM1027* hardware
monitoring chip
Memory
• Four 184-pin DIMM sockets
• Supports DDR 400/333/266
• Up to 4GB of Un-buffered ECC and non-
ECC type memory modules
• Registered Memory is NOT supported
Expansion Slots
• Four 32-bit / 33MHz PCI 2.3 slots
Integrated LAN Controller(s) (Optional)
• Two Gigabit LAN controller
Intel
®
82547 Gigabit Ethernet controller
- Operating at 266MB/s CSA interface
Intel
®
82541 Gigabit Ethernet controller
(Optional)
• One 10/100 Mbps LAN controller
Intel
®
82562 10/100 Mbps LAN controller
Intelligent PCI Graphic
• ATI
®
Rage XL PCI controller
• 8MB Frame Buffer
Integrated PCI IDE (ICH5)
• Dual channel master mode support up
to four IDE devices
• Support for ATA-100 / 66/ 33 IDE drives
and ATAPI compliant devices
Integrated Serial ATA RAID
• Promise
®
PDC20378 SATA RAID
controller
• Two Serial ATA RAID ports and one
Ultra ATA/133 IDE RAID port
• Support up to two SATA and two
ATA-133/100 IDE drives
• Supports IDE RAID 0, 1, 0+1(Need to
install two SATA Hard drivers and two
ATA-133/100 IDE drives
simultaneously)
System Management
• Total of three 3-pin headers
• Three fan headers with tachometer
monitoring
• Watchdog timer
Integrated I/O Interface
• One floppy connector supports up to
two drives
• Eight USB 2.0 ports (two rear
connectors and six ports by headers)
• Two 9-pin serial port (one rear
connector and one header)
• One 25-pin ECP/EPP/SPP parallel port
header
• One IrDA connector (via optional cable)
• Power/IDE LED connectors
1-1
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 1: Introduction
Integrated Serial ATA (ICH5)
• Two Serial ATA Host controllers embedded
in ICH5
• Support two Serial ports running at 150MB/s
Intelligent Platform Management
Interface (Optional)
• QLogic
TM
Zircon Baseboard
Management Controller (BMC) based on
powerful ARM7 technology
• Tailored for IPMI highest 1.5 Spec.
• Supports KCS and BT styles
• Supports flexible Windows and Linux
based Management Solution
• Supports RMCP and SNMP protocols
• Supports ASF standard and EMP
• I
2
C serial multi-master controllers and
UARTs
• Built-in IPMB connector
• Supports remote Power on/off and reset
support (IPMI-over-LAN)
• Server Management Daughter Card
(SMDC) via built-in 2x25 header
BIOS
• Award BIOS 8Mbit Flash ROM
• Support APM 1.2 & ACPI 1.0B
• PnP, DNI 2.0, WFM 2.0 Power
Management
• Support BIOS Boot Specification v1.01
(BBS)
• Supports Watchdog timer ready and
DMI
Rear Panel I/O ports
• Stacked PS/2 Mouse & Keyboard ports
• Stacked two USB2.0 ports and one
RJ45 100/10 LAN port on top
• One Serial and One VGA connectors
• One RJ45 (LAN1) connector with LEDs
• One RJ45 (LAN2) connector with LEDs
(optional)
Power
• On board VRM, 3-phase PWM
• ATX 12V power connector
Regulatory
• EMI - CE, FCC Class B
Form Factor
• ATX footprint
• 305mm x 245mm (12” x 9.6”)
Note: TYAN reserves the right to add support or discontinue support for any OS with or
without notice.
1-2
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
Chapter 2: Board Installation
Installation
You are now ready to install your motherboard. The mounting holes pattern of the Tomcat
i875PR S5102-P matches the ATX specification. Before continuing with installation, confirm
that your chassis supports a standard ATX motherboard.
How to install our products right…. the first time!
The first thing you should do read this user’s manual. It contains important information that will
make configuration and setup much easier. Here are some precautions you should take when
installing your motherboard:
(1) Ground yourself properly before removing your motherboard from the antistatic bag.
Unplug the power from your computer power supply and then touch a safely
grounded object to release static charge (i.e. power supply case). For the safest
conditions, TYAN recommends wearing a static safety wrist strap.
(2) Hold the motherboard by its edges and do not touch the bottom of the board, or flex
the board in any way.
(3) Avoid touching the motherboard components, IC chips, connectors, memory
modules and leads.
(4) Place the motherboard on a grounded antistatic surface or on the antistatic bag that
the board was shipped in.
(5) Inspect the board for damage.
The following pages include details on how to install your motherboard into your chassis, as
well as installing the processor, memory, disk drives and cables.
Note: DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED
2-1
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
2.1 – Board Image
The following is an image of the Tomcat i875PR S5102-P.
The above photograph is purely representative. Due to engineering updates and new
board revisions, certain components may change and or be repositioned. The picture
above may or may not look exactly like the board you received.
The following page includes details on the vital components of this motherboard.
2-2
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
2.2 – Board Parts
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)
J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bottom)
LAN (Top)
KB(Bottom)
Mouse(Top)
LAN2
ATI
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(Optional)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3
SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
This jumper diagram is representative of the latest board revision available at the time
of publishing. The board you receive may or may not look exactly like the above
diagram. The board parts are not to scale.
2-3
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
2.3 – Block Diagram
The following is a block diagram of the Tomcat i875PR S5102-P.
mPGA478
Processor Socket
ICS-952607
VRD10.0
Intel
2-4
82875P MCH
Intel 01EB
ICH5
828
DDR
DDR
DDR
DDR
CSA Interface
Intel 82547
Gigabit
Ethernet
ATI Rage XL
Winbond
W83627F/HF
LPC SIO
FirmWare Hub
Keyboard
Mouse
Floppy
Parallel
Serial 1/2
USB 2.0
8 ports, 480Mb/s
2 X Serial ATA
Ports 150MB/s
2 X ATA 100/66/
33 Ports
Intel 82541
Gigabit Ethernet
(Optional)
Promise
PDC20378
RAID 0, 1, 0+1
2 X Serial ATA
RAID Ports
150MB/s
One ATA 133 IDE
RAID Ports
Intel 82562
10/100 MB LAN
800/533/400 MHz
System Bus
Intel 875P Chipset
Syatem Memory
DDR 400/333/266
Channel A
Channel B
266 MB/s
Four PCI Masters
PCI BUS
LPC Interface
1 x VGA
connector
266 MB/s
Hub Link 1.5
Post Port
ADM1027
Hardware
Monitor
®
®
®
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
2.4 – Jumper Settings & Definitions
Jumper Function Ref. Page
JP3 Clear CMOS Page 2-5
Jumper Example
Jumper OFF – open (without jumper cap)
Jumper ON – closed (with jumper cap)
CMOS Reset (JP3)
13
Normal
13
Clear CMOS
JP3
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bott om)
LAN (Top)
KB(Bottom)
Mouse(Top)
LAN2
AT I
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(Opt iona l)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
You can reset the CMOS settings in case an
incorrect setting causes system instability or
you have forgotten your system / setup
password or have just flashed your BIOS by
using these jumpers.
- Power off system, disconnect power supply
from the motherboard
- Set jumper to Clear CMOS
- Wait about 5 seconds
- Set jumper to Normal (Default)
And plug the power supply back into the
motherboard.
2-5
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
2.5 – Connector Description
Connector Function Ref. Page
J1 Chassis fan connector Page 2-6
J4 COM2 port Page 2-7
J5** SMDC Connector Page 2-10
J6 CPU fan connector Page 2-6
J7 SMBus_0 Connector Page 2-7
J8 Front panel connector Page 2-7
J9 Power fan connector Page 2-6
J12* IDE RAID connector Page 2-8
EFI1 EFI1 connector Page 2-8
LED1 Power On LED Page 2-8
LED2 Post error code for BIOS Page 2-8
LPT1 Printer Port connector Page 2-9
SATA1/SATA2 Serial ATA connector Page 2-9
SATA3/SATA4* Serial ATA RAID connector Page 2-9
USB2/USB3/USB4 USB headers Page 2-9
J11** North bridge fan connector Page 2-10
J16 / J17 / J18** Front panel LAN display headers Page 2-10
J19 / J20 / J21 / J22** Auto fan control connectors Page 2-11
JP4 / JP7** Full speed fan control headers Page 2-11
JP5 / JP6** SMDC I
2
C headers Page 2-11
*SATA RAID (SATA3/SATA4) and IDE RAID (J12) functions by Promise PDC20378 chip.
**(J5, J11, J16, J17, J18, J19, J20, J21, J22, JP4, JP5, JP6 and JP7) These connectors
and jumpers are reserved for OEM use only.
Fan Connector (J1 & J6 & J9)
J1 Chassis fan
Tachometer/speed Read and controlled
J6 CPU fan
Tachometer/speed Read and controlled
J9 Power fan
J1
J9
J6
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bottom)
LAN (Top)
KB(Bottom)
Mou se( Top)
LAN2
ATI
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 L AN
(Optional)
Intel
GbE LAN
(Opt iona l)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Tachometer/speed Read and controlled
2-6
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
COM2 port (J4, via a cable)
1
9
2
10
J4
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB
(
Bottom
)
LAN (Top)
KB(Bottom)
Mou se(Top)
LAN2
ATI
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(Optional)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Signal
DCD
RX
TX
DTR
GND
Pin#
1
3
5
7
9
Pin#
2
4
6
8
10
Signal
DSR
RTS
CTS
RI
NC/Key
SMBus_0 Connector (J7)
1
4
Pin 1: SMBUS_DATA
Pin 2: GND
Pin 3: SMBUS_CLK
Pin 4: NC
J7
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bottom)
LAN (Top)
KB(Bo ttom)
Mou se(To p)
LAN2
ATI
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(Opt iona l)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Use this connector to connect external
SMBUS devices
Front Panel Connector (J8)
Your chassis will usually come with connectors to install onto the motherboard, such as HD
and Power LEDs. The Front Panel Connector (J8) has been implemented for such purposes.
1 2
17 18
(1, 3) HDD-LED
(5, 7) RST
(9, 11, 13, 15, 17) IR
(2, 4, 6) PW-LED
(8, 10) PWR
(12, 14, 16, 18) SPKR
Function Pin Pin Function
HDD_LED+ 1 2 Power_LED+
HDD_LED- 3 4 GND
GND 5 6 GND
Reset Button 7 8 Power Button
VCC 9
10
GND
CIRRX 11 12 VCC
IRRX 13 14 GND
GND 15 16 NC
J8
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bottom)
LAN (Top)
KB(Bottom)
Mouse(Top)
LAN2
AT I
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(Optional)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
IRTX 17 18 Speaker
2-7
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
IDE RAID Connectors (J12) (from Promise PDC20378 chip)
J12
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB
(
Bottom
)
LAN ( Top)
KB(Bott om)
Mou se(Top)
LAN2
ATI
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(Opti onal)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Supports IDE RAID 0, 1, 0+1 (Need to install
two SATA Hard drives plugged into SATA3
and SATA4 connectors simultaneously)
EFI1 Connector
EFI1
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bo ttom)
LAN ( To p)
KB(Bott om)
Mo us e(To p)
LAN2
AT I
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(O ptio nal )
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Pin 1: GND
Pin 3: USBP2+
Pin 5: TXD
Pin 7: RXD
Pin 9: NC
Pin 2: VCC
Pin 4: USBP2-
Pin 6: VCC3
Pin 8: GND
Pin 10: +12V
LED Information (LED1 & LED2)
LED1: Power on LED
LED2
LED1
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Botto m)
LAN (Top)
KB(Bottom)
Mou se (To p)
LAN2
ATI
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(O ptio nal)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
LED2: Post error code for BIOS
(Ref. Appendix II)
2-8
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
Printer Port Connector (LPT1)
LPT1
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (B ottom)
LAN (Top)
KB(Bottom)
Mouse(Top)
LAN2
ATI
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(Optional)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Pin 1: STB-
Pin 3: PD0
Pin 5: PD1
Pin 7: PD2
Pin 9: PD3
Pin 11: PD4
Pin 13: PD5
Pin 15: PD6
Pin 17: PD7
Pin 19: ACK-
Pin 21: BUSY
Pin 23: PE
Pin 25: SLCT
Pin 2: AFD-
Pin 4: ERR-
Pin 6: INIT-
Pin 8: SLIN-
Pin 10: GND
Pin 12: GND
Pin 14: GND
Pin 16: GND
Pin 18: GND
Pin 20: GND
Pin 22: GND
Pin 24: GND
Pin 26: NC
Serial ATA Connectors (SATA1 & SATA2 & SATA3 & SATA4)
SATA1 / SATA2 (from ICH5): RAID function is NOT supported
SATA3 / SATA4 (from Promise PDC20378 chip): RAID function is supported
1 7
Pin 1 2 3 4 5 6 7
Signal GND TXP TXN GND RXN RXP GND
SATA3
SATA2
SATA1
SATA4
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Botto m)
LAN (Top)
KB(Bottom)
Mou se( Top)
LAN2
AT I
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LA N
(Optional)
Intel
GbE LAN
(Opt iona l)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Supports serial ATA devices
Front USB Connector (USB2 & USB3 & USB4)
10
2
9
1
Pin 10: No Connect
Pin 8: GND
Pin 6: +Data
Pin 4: -Data
Pin 2: +5VDU
Pin 9: Key
Pin 7: GND
Pin 5: +Data
Pin 3: -Data
Pin 1: +5VDU
USB2
USB3
USB4
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
US B (Bottom)
LAN (Top)
KB(Bottom)
Mouse(Top)
LAN2
AT I
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(O pt io nal )
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Use the USB2 & USB3 & USB4 header here
for front panel USB 2.0 connectors (via the
cable)
2-9
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
OEM Reserved Connectors and Jumpers as below:
SMDC Connector (J5)**
J5
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB
(
Bottom
)
LAN ( Top)
KB(Bottom)
Mouse(Top)
LAN2
ATI
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 L AN
(Optional)
Intel
GbE LAN
(Opt io nal)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Connect Server Management Daughter Card
(SMDC)
Compatible with Tyan M3289 (SMDC)
See Appendix III for details In Tyan SMDC
North bridge fan connector (J11)**
+12V
N
C
GND
J11
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bottom)
LAN (Top)
KB(Bottom)
Mou se (To p)
LAN2
AT I
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(Opt io nal)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
Without PWM fan control and fan speed
reading
Front panel LAN display headers (J16, J17 and J18)**
1
4
Pin 4: GND
Pin 3: Link LED
Pin 2: GND
Pin 1: Link LED
J17
J18
J16
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bo ttom)
LAN (Top)
KB(Bottom)
Mouse(Top)
LAN2
ATI
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(Opt ional)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
J16: Intel 82547 LAN Link LED
J17: Intel 82541 LAN Link LED
J18: Intel 82562 LAN Link LED
2-10
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
Auto fan control connectors (J19, J20, J21 and J22)**
+12V
GND
Speed
J20
J21
J22
J19
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bottom)
LAN (Top)
KB(Bottom)
Mou se( Top)
LAN2
AT I
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LA N
(Optional)
Intel
GbE LAN
(Opt iona l)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
With PWM fan control
With fan speed reading
Full speed fan control headers (JP4 and JP7)**
1
OPEN (Default)
Auto fan control
1
JP7
JP4
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (Bottom)
LAN (Top)
KB(Bottom)
Mou se( Top)
LAN2
AT I
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LA N
(Optional)
Intel
GbE LAN
(Opt iona l)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
CLOSED
Full speed fan control
Without PWM fan control
SMDC I
2
C headers (JP5 and JP6)**
3
1
JP5 and JP6 CLOSED: 1 – 2
Without SMDC I
2
C function
3
1
JP6
JP5
S5102-P
USB3
1
1
1
1
KB-MO1
USB1
CN1 (COM1)J2 (VGA)
PWR1
LAN1
J9
BIOS
J1
Intel
875P
Intel
ICH5
PCI2PCI3
SATA2
FDD J10
JP3
CMOS
BT1
SEC-IDE J15
PRI-IDE J13
1
Winbond
W83627HF
PCI4
USB4
1
LED2
PCI1
RAID-IDE J12
Chassis
FAN
J4
Intel
GbE LAN
LED1
1
USB (B ottom)
LAN (Top)
KB(Bottom)
Mouse(Top)
LAN2
AT I
RAGE XL
1
LPT1
USB2
SMDC J5
POWER FAN
EFI1
COM2
8MB
SDRAM
Intel
10/100 LAN
(Optional)
Intel
GbE LAN
(
Optional
)
1
JP6
JP5
1
SATA1
1 1 1
J19
J21
J22
1
JP7
JP4
SATA3 SATA4
1
J7
J17
J18
J16
1
J6
CPU - FAN
1
J11
NB - FAN
J20
1
(Default)
JP5 and JP6 CLOSED: 2 – 3
With SMDC I
2
C function
2-11
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
2.6 – Mounting the Motherboard
Before installing your motherboard, make sure your chassis has the necessary motherboard
support studs installed. These studs are usually metal and are gold in color. Usually, the
chassis manufacturer will pre-install the support studs. If you’re unsure of stud placement,
simply lay the motherboard inside the chassis and align the screw holes of the motherboard to
the studs inside the case. If there are any studs missing, you will know right away since the
motherboard will not be able to be securely installed.
Some chassis’ include plastic studs instead of metal. Although the plastic studs are usable,
TYAN recommends using metal studs with screws that will fasten the motherboard more
securely in place.
- Memory Type: The Tomcat i875PR S5102-P supports unbuffered ECC and non-ECC
type memory modules. Registered Memory is NOT supported.
Below is a chart detailing what the most common motherboard studs look like and how they
should be installed it.
TIP: Use metal studs if possible, as they hold the motherboard into place more securely than
plastic standoffs.
2-12
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
2.7 – Installing the Memory
Before attempting to install any memory, make sure that the memory you have is compatible
with the motherboard as well as the processor. For example, while PC1600 DDR modules are
compatible with all DDR based motherboards, they will not work if you are required to run the
motherboard and processor buses at 133MHz. For this, PC2100 DDR modules are required.
Critically important is whether you’re using the recommended memory for the current board
you have. For this information, please check TYAN’s web site at:
www.tyan.com
The following diagram shows the types of RAM modules you may encounter depending on
your board:
DDR Unbuffered ECC
DDR Unbuffered
Here are a few key points to note before installing memory into your Tomcat i875PR S5102-P:
• 128MB, 256MB, 512MB and 1GB unbuffered ECC and non-ECC
PC2100/PC2700/PC3200
DDR memory modules are supported
• All installed memory will be automatically detected - no need to set any jumpers
• The Tomcat i875PR S5102-P supports up to 4GB of memory
• Registered Memory is NOT supported.
• You can install either single- or double-sided modules on this board. Each DIMM
can work respectively for single-channel mode and dual-channel mode. Please note
that the same type and density memory modules are necessary while using dual-
channel DDR, otherwise it may cause system instability.
Please refer to the following table for detailed dual-channel DDR.
Channel A Channel B Dual-Channel Mode
DIMM1
(Blue)
DIMM2
(Black)
DIMM3
(Blue)
DIMM4
(Black)
System
Density
Two DIMM Symmetrical
Population
9 9
256MB~2GB
Two DIMM Symmetrical
Population
9 9
256MB~2GB
Four DIMM Symmetrical
Population
9 9 9 9
512MB~4GB
Note
1. 9: Installing128MB~1GB Memory modules
2. Symmetrical DIMMs must be identical
- Same DRAM Technology, eg 128M-bit, 256-bit, etc.
- Same DRAM bus width, eg x8 or x16
- Matched Sided DIMMs (Single Sided or Double Sided)
2-13
http://www.tyan.com
Tomcat i875PR S5102-P Chapter 2: Board Installation
• Supported System Bus Frequency and Memory Speed Combinations
CPU FSB DDR DIMM Type Memory Frequency
800MHz PC3200, PC2700*, PC2100 400, 333*, 266 MHz
533MHz PC2700, PC2100 333, 266 MHz
400MHz PC2100 266 MHz
* When using 800MHz CPU FSB, PC2700 DDR DIMMS may run only at 320MHz (not 333MHz) due
to chipset limitations.
Note:
While using ECC type memory, it will take longer time to post. Due to the manner in which it
counts the memory and has to write zero’s to every bit of the stick before progressing through
the POST.
2.8 – Memory Installation Procedure
When installing memory modules, make sure the modules align properly with the memory
socket. There should be keys (small indents) on your memory modules that fit according to the
keys in the memory socket. DDR modules and sockets have only one key, which is slightly
near the center of the module/socket. The method of installing memory modules is detailed in
the following diagrams.
Once the memory modules are firmly seated in the socket, two clamps on either side will close
and secure the module into the socket. Sometimes you may need to close the clamps
manually.
To remove the memory module, simply push the clamps outwards until the memory module
pops up. Then simply remove the module.
TIP: When installing memory, a module may require a considerable amount of force to seat
properly, although this is very rare. To avoid bending and damaging your motherboard, place
it on its anti-static bag and onto a flat surface, and then proceed with memory installation.
Note: You MUST unplug the power connector to the motherboard before performing system
hardware changes, to avoid damaging the board or expansion device
2-14
http://www.tyan.com
/