Tyan Tomcat i875P S5102 User manual

Tomcat i875P S5102 User’s Manual

i

http://www.tyan.com

Tomcat i875P

///

S5102

Revision 1.03

manual may be reproduced or translated without prior written consent from TYAN Computer

Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Tomcat, i875P and S5102 are trademarks of TYAN Computer Corporation.

Intel, Pentium 4, and combinations thereof are trademarks of Intel Corporation.

Promise is a trademark of Promise Technology, Inc.

Award, AwardBIOS are trademarks of Award Software Incorporated.

Microsoft and Windows are trademarks of Microsoft Corporation.

IBM, PC, AT and PS/2 are trademarks of IBM Corporation.

ATI, ATI RAGE is a trademark of ATI Technologies Incorporated.

Winbond is a trademark of Winbond Electronics Corporation.

Analog Devices is a trademark of Analog Devices, Inc.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has

been reviewed for accuracy and reliability prior to printing. TYAN assumes no liability

whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of

TYAN products including liability or warranties relating to fitness for a particular purpose or

merchantability. TYAN retains the right to make changes to product descriptions and/or

specifications at any time, without notice. In no event will TYAN be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting

from errors or inaccuracies of information contained in this document.

Tomcat i875P S5102 Table of Contents

ii

http://www.tyan.com

Table of Contents

Before you begin… ................................................................................................................. iv

Chapter 1: Introduction.........................................................................................................1-1

1.1 – Congratulations!...................................................................................................... 1-1

1.2 – Hardware Specifications ......................................................................................... 1-1

Chapter 2: Board Installation ............................................................................................... 2-1

2.1 – Board Image ........................................................................................................... 2-2

2.2 – Board Parts ............................................................................................................. 2-3

2.3 – Block Diagram......................................................................................................... 2-4

2.4 – Jumper Settings & Definitions................................................................................. 2-5

2.5 – Connector Description ............................................................................................ 2-6

2.6 – Mounting the Motherboard.................................................................................... 2-12

2.7 – Installing the Memory............................................................................................ 2-14

2.8 – Memory Installation Procedure ............................................................................. 2-15

2.9 – Installing the Processor and Heatsink................................................................... 2-16

2.10 – Attaching Drive Cables ....................................................................................... 2-18

2.11 – Installing Add-In Cards........................................................................................ 2-20

2.12 – Connecting External Devices.............................................................................. 2-21

2.13 – Installing the Power Supply................................................................................. 2-23

2.14 – Finishing Up ........................................................................................................ 2-23

Chapter 3: BIOS Setup..........................................................................................................3-1

3.1 – Main BIOS Setup .................................................................................................... 3-2

3.2 – Standard CMOS Features ...................................................................................... 3-4

3.3 – Advanced BIOS Features ....................................................................................... 3-5

3.4 – Advanced Chipsets Features.................................................................................. 3-9

3.5 – Integrated Peripherals........................................................................................... 3-10

3.6 – Power Management Setup ................................................................................... 3-14

3.7 – PnP/PCI Configurations ........................................................................................ 3-17

3.8 – PC Health Status .................................................................................................. 3-18

3.9 – Frequency/Voltage Control ................................................................................... 3-20

3.10 – Load Fail-Safe Defaults ...................................................................................... 3-21

3.11 – Load Optimized Defaults..................................................................................... 3-21

3.12 – Supervisor/User Password Setting ..................................................................... 3-22

3.13 – Exit Selecting ...................................................................................................... 3-23

Chapter 4: SATA/RAID Setup

(for SATA RAID mode

l) ...................................................... 4-1

4.1 – Getting Started........................................................................................................ 4-1

4.2 - Creating Your Disk Array ......................................................................................... 4-2

Creating an Array for Performance ........................................................................... 4-4

Creating a Security Array with New Drives ............................................................... 4-4

Creating a Security Array with an Existing Data Drive.............................................. 4-5

4.3 - Installing Software Drivers ....................................................................................... 4-6

New Windows 2000/XP Installation .......................................................................... 4-6

Existing Windows 2000/XP Installation..................................................................... 4-6

Confirming Windows 2000/XP Installation................................................................ 4-6

New Windows 98/Me Installation .............................................................................. 4-7

Existing Windows 98/Me Installation ........................................................................ 4-7

New Windows NT 4.0 Installation ............................................................................. 4-8

Existing Windows NT 4.0 Installation........................................................................ 4-8

4.4 - Using FastBuild™ Configuration Utility.................................................................... 4-9

Viewing PDC20378 BIOS Screen............................................................................. 4-9

Navigating the FastBuild™ Setup Menu................................................................. 4-10

Creating Arrays Automatically ................................................................................ 4-11

Optimize Array For.................................................................................................. 4-11

Tomcat i875P S5102 Table of Contents

iii

http://www.tyan.com

Viewing Drive Assignments .................................................................................... 4-12

Deleting An Array.................................................................................................... 4-12

Rebuilding A Mirrored Array.................................................................................... 4-14

Chapter 5: Diagnostics .........................................................................................................5-1

5.1 Beep Codes ............................................................................................................... 5-1

5.2 Flash Utility.................................................................................................................5-1

Appendix I: Glossary ............................................................................................................6-1

Appendix II: Post Error Code for BIOS ............................................................................... 6-7

Appendix III: SMDC Information ........................................................................................ 6-12

Technical Support .......................................................................................................... 6-13

Tomcat i875P S5102 Before you begin…

iv

http://www.tyan.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Tomcat i875P S5102 motherboard

1x 34-Pin floppy drive cable

1x Ultra-DMA-133/100/66/33 IDE cable

1x Tomcat i875P S5102 User’s Manual

1x Tomcat i875P S5102 Quick Reference Guide

1x TYAN driver CD

1x I/O shield

1 x Promise FastTrak 378 RAID Driver Diskette

1 x Cable set: 9-pin Serial and 25-pin Parallel

2 x Serial ATA power cable

4 x Serial ATA cable

1 x USB2.0 cable

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

Tomcat i875P S5102 Chapter 1: Introduction

1-1

http://www.tyan.com

Chapter 1: Introduction

1.1 – Congratulations!

You have purchased one of the most powerful solutions for the Intel Pentium



4 processor, the

Tomcat i875P S5102 Based on Intel 875P chipset, this platform offers convenient remote

Intelligent Platform Management Interface (IPMI) monitoring through a Server Management

Daughter Card. The Tomcat i875P S5102 are ATX form factor, onboard Gigabit Ethernet port,

Fast Ethernet port, Serial ATA, IDE RAID and an onboard ATI 8MB PCI RAGE XL VGA.

Remember to visit TYAN’s Website at http://www.tyan.com

. There you can find information on

all of TYAN’s products with FAQs, distributors list, and BIOS setting explanations.

1.2 – Hardware Specifications

Processors

• Socket 478 processor

• Supports single Intel Pentium



4 processor

“Northwood / Prescott”

• Onboard VRM10

• Front-Side Bus support for 800/533/400MHz

Chipset

• Intel 875P North Bridge chipset

• Intel ICH5 South Bridge chipset

• Winbond W83627HF LPC I/O chip

• Analog devices ADM1027* hardware

monitoring chip

*NOTE: ADM1027 chip may be available on

some Tomcat i875P models. Check the Tyan

website for updates: http://www.tyan.com

Memory

• Four 184-pin DIMM sockets

• Supports DDR 400/333/266

• Up to 4GB of Un-buffered ECC and non-

ECC type memory modules

• Registered Memory is NOT supported

Expansion Slots

• Four 32-bit / 33MHz PCI 2.3 slots

Integrated LAN Controller(s) (Optional)

• Two Gigabit LAN controller

Intel 82547EI Gigabit Ethernet controller

- Operating at 266MB/s CSA interface

Intel 82541EI Gigabit Ethernet controller

(Optional)

• One 10/100 Mbps LAN controller

Intel 82562ET 10/100 Mbps LAN controller

Intelligent PCI Graphic

• ATI Rage XL PCI controller

• 8MB Frame Buffer

Integrated PCI IDE (ICH5)

• Dual channel master mode support up

to four IDE devices

• Support for ATA-100 / 66/ 33 IDE drives

and ATAPI compliant devices

Integrated Serial ATA RAID

• Promise PDC20378 SATA RAID

controller

• Two Serial ATA RAID ports and one

Ultra ATA/133 IDE RAID port

• Support up to two SATA and two

ATA-133/100 IDE drives

• Supports IDE RAID 0, 1, 0+1(Need to

install two SATA Hard drivers and two

ATA-133/100 IDE drives

simultaneously)

System Management

• Total of three 3-pin headers

• Three fan headers with tachometer

monitoring

• Watchdog timer

Integrated I/O Interface

• One floppy connector supports up to

two drives

• Eight USB 2.0 ports (two rear

connectors and six ports by headers)

• Two 9-pin serial port (one rear

connector and one header)

• One 25-pin ECP/EPP/SPP parallel port

header

• One IrDA connector (via optional cable)

• Power/IDE LED connectors

Tomcat i875P S5102 Chapter 1: Introduction

1-2

http://www.tyan.com

Integrated Serial ATA (ICH5)

• Two Serial ATA Host controllers embedded

in ICH5

• Support two Serial ports running at 150MB/s

Intelligent Platform Management

Interface (Optional)

• QLogic

TM

Zircon Baseboard

Management Controller (BMC) based on

powerful ARM7 technology

• Tailored for IPMI highest 1.5 Spec.

• Supports KCS and BT styles

• Supports flexible Windows and Linux

based Management Solution

• Supports RMCP and SNMP protocols

• Supports ASF standard and EMP

• I

2

C serial multi-master controllers and

UARTs

• Built-in IPMB connector

• Supports remote Power on/off and reset

support (IPMI-over-LAN)

• Server Management Daughter Card

(SMDC) via built-in 2x25 header

BIOS

• Award BIOS 4Mbit or 8Mbit Flash ROM

• Support APM 1.2 & ACPI 1.0B

• PnP, DNI 2.0, WFM 2.0 Power

Management

• Support BIOS Boot Specification v1.01

(BBS)

• Supports Watchdog timer ready and

DMI

Rear Panel I/O ports

• Stacked PS/2 Mouse & Keyboard ports

• Stacked two USB2.0 ports and one

RJ45 100/10 LAN port on top

• One Serial and One VGA connectors

• One RJ45 (LAN1) connector with LEDs

• One RJ45 (LAN2) connector with LEDs

(optional)

Power

• On board VRM, 3-phase PWM

• ATX 12V power connector

Regulatory

• EMI - CE, FCC Class B

Form Factor

• ATX footprint

• 305mm x 245mm (12” x 9.6”)

Note: TYAN reserves the right to add support or discontinue support for any OS with or

without notice.

Tomcat i875P S5102 Chapter 2: Board Installation

2-1

http://www.tyan.com

Chapter 2: Board Installation

Installation

You are now ready to install your motherboard. The mounting holes pattern of the Tomcat

i875P S5102 matches the ATX specification. Before continuing with installation, confirm that

your chassis supports a standard ATX motherboard.

How to install our products right…. the first time!

The first thing you should do read this user’s manual. It contains important information that

will make configuration and setup much easier. Here are some precautions you should take

when installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer power supply and then touch a safely

grounded object to release static charge (i.e. power supply case). For the safest

conditions, TYAN recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board, or flex

the board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors, memory

modules and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic bag that

the board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your chassis, as

well as installing the processor, memory, disk drives and cables.

Note: DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

Tomcat i875P S5102 Chapter 2: Board Installation

2-2

http://www.tyan.com

2.1 – Board Image

The following is an image of the Tomcat i875P S5102.

The above photograph is purely representative. Due to engineering updates and new

board revisions, certain components may change and or be repositioned. The picture

above may or may not look exactly like the board you received.

The following page includes details on the vital components of this motherboard.

Tomcat i875P S5102 Chapter 2: Board Installation

2-3

http://www.tyan.com

2.2 – Board Parts

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)

J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB (Bottom)

LAN (Top)

KB(Bottom)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

This jumper diagram is representative of the latest board revision available at the time

of publishing. The board you receive may or may not look exactly like the above

diagram. The board parts are not to scale.

Tomcat i875P S5102 Chapter 2: Board Installation

2-4

http://www.tyan.com

2.3 – Block Diagram

The following is a block diagram of the Tomcat i875P S5102.

mPGA478

Processor Socket

ICS-952607

VRD10.0

Intel 82875P MCH

Intel 82801EB

ICH5

DDR

CSA Interface

Intel 82547EI

Gigabit

Ethernet

ATI Rage XL

Winbond

W83627F/HF

LPC SIO

FirmWare Hub

Keyboard

Mouse

Floppy

Parallel

Serial 1/2

USB 2.0

8 ports, 480Mb/s

2 X Serial ATA

Ports 150MB/s

2 X ATA 100/66/

33 Ports

Intel 82541EI

Gigabit Ethernet

(Optional)

Promise

PDC20378

RAID 0, 1, 0+1

2 X Serial ATA

RAID Ports

150MB/s

One ATA 133 IDE

RAID Ports

Intel 82562EM

10/100 MB LAN

800/533/400 MHz

System Bus

Intel 875P Chipset

Syatem Memory

DDR 400/333/266

Channel A

Channel B

266 MB/s

Four PCI Masters

PCI BUS

LPC Interface

1 x VGA

connector

266 MB/s

Hub Link 1.5

Post Port

ADM1027

Hardware

Monitor

(optional)

®

Tomcat i875P S5102 Chapter 2: Board Installation

2-5

http://www.tyan.com

2.4 – Jumper Settings & Definitions

Jumper Function Ref. Page

JP3 Clear CMOS Page 2-5

Jumper Example

Jumper OFF – open (without jumper cap)

Jumper ON – closed (with jumper cap)

CMOS Reset (JP3)

13

Normal

13

Clear CMOS

JP3

S5102

USB3

1

KB-MO 1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winb ond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB (Bottom)

LAN (Top)

KB(B ottom)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 L AN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

You can reset the CMOS settings in case an

incorrect setting causes system instability or

you have forgotten your system / setup

password or have just flashed your BIOS by

using these jumpers.

- Power off system, disconnect power supply

from the motherboard

- Set jumper to Clear CMOS

- Wait about 5 seconds

-

Set jumper to Normal (Default)

A

nd plug the power supply back into the

motherboard.

Tomcat i875P S5102 Chapter 2: Board Installation

2-6

http://www.tyan.com

2.5 – Connector Description

Connector Function Ref. Page

J1 Chassis fan connector Page 2-6

J4 COM2 port Page 2-7

J5 SMDC Connector Page 2-7

J6 CPU fan connector Page 2-6

J7 SMBus_0 Connector Page 2-8

J8 Front panel connector Page 2-8

J9 Power fan connector Page 2-6

J12* IDE RAID connector Page 2-8

EFI1 EFI1 connector Page 2-9

LED1 Power On LED Page 2-9

LED2 Post error code for BIOS Page 2-9

LPT1 Printer Port connector Page 2-9

SATA1/SATA2 Serial ATA connector Page 2-10

SATA3/SATA4* Serial ATA RAID connector Page 2-10

USB2/USB3/USB4 USB headers Page 2-10

J11** North bridge fan connector Page 2-10

J16 / J17 / J18** Front panel LAN display headers Page 2-11

J19 / J20 / J21 / J22** Auto fan control connectors Page 2-11

JP4 / JP7** Full speed fan control headers Page 2-11

JP5 / JP6** SMDC I

2

C headers Page 2-12

*SATA RAID (SATA3/SATA4) and IDE RAID (J12) functions by Promise PDC20378 chip.

**(J11, J16, J17, J18, JP4, JP5, JP6 and JP7) These connectors and jumpers are for

OEM use only.

Fan Connector (J1 & J6 & J9)

J1 Chassis fan

Tachometer/speed Read and controlled

J6 CPU fan

Tachometer/speed Read and controlled

J9 Power fan

J1

J9

J6

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bottom)

Mouse(Top)

LAN2

AT I

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Tachometer/speed Read and controlled

Tomcat i875P S5102 Chapter 2: Board Installation

2-7

http://www.tyan.com

COM2 port (J4, via a cable)

1

9

2

10

Signal

DCD

TXD

GND

RTS

RI

Pin#

1

3

5

7

9

Pin#

2

4

6

8

10

Signal

RXD

DTR

DSR

CTS

Key

Note:

The above shows the pin assignments

for PCB Rev.: 03MOA, 03MOAA and

03MOAB use only.

J4

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bo ttom)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Signal

DCD

RX

TX

DTR

GND

Pin#

1

3

5

7

9

Pin#

2

4

6

8

10

Signal

DSR

RTS

CTS

RI

NC/Key

SMDC Connector (J5)

J5

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bottom)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Connect Server Management Daughter Card

(SMDC)

Compatible with Tyan M3289 (SMDC)

See Appendix III for details In Tyan SMDC

Tomcat i875P S5102 Chapter 2: Board Installation

2-8

http://www.tyan.com

SMBus_0 Connector (J7)

1

4

Pin 1: SMBUS_DATA

Pin 2: GND

Pin 3: SMBUS_CLK

Pin 4: NC

J7

S5102

USB3

1

KB-MO 1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bottom)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Use this connector to connect external

SMBUS devices

Front Panel Connector (J8)

Your chassis will usually come with connectors to install onto the motherboard, such as HD

and Power LEDs. The Front Panel Connector (J8) has been implemented for such purposes.

1 2

17 18

(1, 3) HDD-LED

(5, 7) RST

(9, 11, 13, 15, 17) IR

(2, 4, 6) PW-LED

(8, 10) PWR

(12, 14, 16, 18) SPKR

Function Pin Pin Function

HDD_LED+

1 2

Power_LED+

HDD_LED-

3 4

GND

5 6

GND

Reset Button

7 8

Power Button

VCC

9

10

GND

CIRRX

11 12

VCC

IRRX

13 14

GND

GND 15 16 NC

J8

S5102

USB3

1

KB-MO1

USB1

CN1

(

COM1

)

J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB (Bo ttom)

LAN (Top)

KB(Bottom)

Mouse(Top)

LAN2

AT I

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 L AN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

IRTX

17 18

Speaker

IDE RAID Connectors (J12) (from Promise PDC20378 chip)

J12

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB (B ottom)

LAN (Top)

KB(Botto m)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Supports IDE RAID 0, 1, 0+1 (Need to install

two SATA Hard drives plugged into SATA3

and SATA4 connectors simultaneously)

Tomcat i875P S5102 Chapter 2: Board Installation

2-9

http://www.tyan.com

EFI1 Connector

EFI1

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bo ttom)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 L AN

(Optional)

Intel

GbE LAN

(

Optional

)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Pin 1: GND

Pin 3: USBP2+

Pin 5: TXD

Pin 7: RXD

Pin 9: NC

Pin 2: VCC

Pin 4: USBP2-

Pin 6: VCC3

Pin 8: GND

Pin 10: +12V

LED Information (LED1 & LED2)

LED1: Power on LED

LED2

LED1

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bo ttom)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

LED2: Post error code for BIOS

(Ref. Appendix II)

Printer Port Connector (LPT1)

LPT1

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bott om)

Mouse(Top)

LAN2

AT I

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(

Option al

)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Pin 1: STB-

Pin 3: PD0

Pin 5: PD1

Pin 7: PD2

Pin 9: PD3

Pin 11: PD4

Pin 13: PD5

Pin 15: PD6

Pin 17: PD7

Pin 19: ACK-

Pin 21: BUSY

Pin 23: PE

Pin 25: SLCT

Pin 2: AFD-

Pin 4: ERR-

Pin 6: INIT-

Pin 8: SLIN-

Pin 10: GND

Pin 12: GND

Pin 14: GND

Pin 16: GND

Pin 18: GND

Pin 20: GND

Pin 22: GND

Pin 24: GND

Pin 26: NC

Tomcat i875P S5102 Chapter 2: Board Installation

2-10

http://www.tyan.com

Serial ATA Connectors (SATA1 & SATA2 & SATA3 & SATA4)

SATA1 / SATA2 (from ICH5): RAID function is NOT supported

SATA3 / SATA4 (from Promise PDC20378 chip): RAID function is supported

1 7

Pin 1 2 3 4 5 6 7

Signal

GND TXP TXN GND RXN RXP GND

SATA3

SATA2

SATA1

SATA4

S5102

USB3

1

KB-MO 1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Botto m)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 L AN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Supports serial ATA devices

Front USB Connector (USB2 & USB3 & USB4)

10

2

9

1

Pin 10: No Connect

Pin 8: GND

Pin 6: +Data

Pin 4: -Data

Pin 2: +5VDU

Pin 9: Key

Pin 7: GND

Pin 5: +Data

Pin 3: -Data

Pin 1: +5VDU

USB2

USB3

USB4

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bo ttom)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(

Optio nal

)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Use the USB2 & USB3 & USB4 header here

for front panel USB 2.0 connectors (via the

cable)

OEM Reserved Connectors and Jumpers as below:

North bridge fan connector (J11)**

+12V

NC

GND

J11

S5102

USB3

1

KB-MO 1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB (Bottom)

LAN (Top)

KB(Bo ttom)

Mouse(Top)

LAN2

AT I

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 L AN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

Without PWM fan control and fan speed

reading

Tomcat i875P S5102 Chapter 2: Board Installation

2-11

http://www.tyan.com

Front panel LAN display headers (J16, J17 and J18)**

1

4

Pin 4: GND

Pin 3: Link LED

Pin 2: GND

Pin 1: Link LED

J17

J18

J16

S5102

USB3

1

KB-MO1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB (Bo ttom)

LAN (Top)

KB(Botto m)

Mouse(Top)

LAN2

AT I

RAGE XL

1

LPT1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(

Optional

)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

J16:

Intel 82547 LAN Link LED

J17:

Intel 82541 LAN Link LED

J18:

Intel 82562 LAN Link LED

Auto fan control connectors (J19, J20, J21 and J22)**

+12V

GND

Speed

J20

J21

J22

S5102

USB3

1

KB-MO 1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB (Bo ttom)

LAN (Top)

KB(Bottom )

Mouse(Top)

LAN2

AT I

RAGE XL

1

LPT 1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

J19

With PWM fan control

With fan speed reading

Full speed fan control headers (JP4 and JP7)**

1

OPEN

(Default)

Auto fan control

1

JP7

JP4

S5102

USB3

1

KB-MO 1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bo ttom)

Mouse(Top)

LAN2

AT I

RAGE XL

1

LPT 1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 LAN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

CLOSED

Full speed fan control

Without PWM fan control

Tomcat i875P S5102 Chapter 2: Board Installation

2-12

http://www.tyan.com

SMDC I

2

C headers (JP5 and JP6)**

3

1

JP5 and JP6 CLOSED: 1 – 2

Without SMDC I

2

C function

3

1

JP6

JP5

S5102

USB3

1

KB-MO 1

USB1

CN1 (COM1)J2 (VGA)

PWR1

LAN1

J9

BIOS

J1

Intel

875P

Intel

ICH5

PCI2PCI3

SATA2

FDD J10

JP3

CMOS

BT1

SEC-IDE J15

PRI-IDE J13

1

Winbond

W83627HF

PCI4

USB4

1

LED2

PCI1

RAID-IDE J12

Chassis

FAN

J4

Intel

GbE LAN

LED1

1

USB ( Bottom)

LAN (Top)

KB(Bottom)

Mouse(Top)

LAN2

ATI

RAGE XL

1

LPT 1

USB2

1

JP2

SMDC J5

POWER FAN

EFI1

COM2

8MB

SDRAM

Intel

10/100 L AN

(Optional)

Intel

GbE LAN

(Optional)

1

JP6

JP5

1

SATA1

1 1 1

J19

J21

J22

1

JP7

JP4

SATA3

SATA4

1

J7

J17

J18

J16

1

J6

CPU - FAN

1

J11

NB - FAN

J20

1

(Default)

JP5 and JP6 CLOSED: 2 – 3

With SMDC I

2

C function

2.6 – Mounting the Motherboard

Before installing your motherboard, make sure your chassis has the necessary motherboard

support studs installed. These studs are usually metal and are gold in color. Usually, the

chassis manufacturer will pre-install the support studs. If you’re unsure of stud placement,

simply lay the motherboard inside the chassis and align the screw holes of the motherboard to

the studs inside the case. If there are any studs missing, you will know right away since the

motherboard will not be able to be securely installed.

Some chassis’ include plastic studs instead of metal. Although the plastic studs are usable,

TYAN recommends using metal studs with screws that will fasten the motherboard more

securely in place.

- Memory Type

: The Tomcat i875P S5102 supports unbuffered ECC and non-ECC type

memory modules. Registered Memory is NOT supported.

Below is a chart detailing what the most common motherboard studs look like and how they

should be installed it.

Tomcat i875P S5102 Chapter 2: Board Installation

2-13

http://www.tyan.com

TIP: Use metal studs if possible, as they hold the motherboard into place more securely than

plastic standoffs.

Tomcat i875P S5102 Chapter 2: Board Installation

2-14

http://www.tyan.com

2.7 – Installing the Memory

Before attempting to install any memory, make sure that the memory you have is compatible

with the motherboard as well as the processor. For example, while PC1600 DDR modules are

compatible with all DDR based motherboards, they

will not

work if you are required to run the

motherboard and processor buses at 133MHz. For this, PC2100 DDR modules are required.

Critically important is whether you’re using the recommended memory for the current board

you have. For this information, please check TYAN’s web site at:

www.tyan.com

The following diagram shows the types of RAM modules you may encounter depending on

your board:

DDR Unbuffered ECC

DDR Unbuffered

Here are a few key points to note before installing memory into your Tomcat i875P S5102:

• 128MB, 256MB, 512MB and 1GB unbuffered ECC and non-ECC

PC2100/PC2700/PC3200

DDR memory modules are supported

• All installed memory will be automatically detected - no need to set any jumpers

• The Tomcat i875P S5102 supports up to 4GB of memory

• Registered Memory is NOT supported.

• You can install either single- or double-sided modules on this board. Each DIMM

can work respectively for single-channel mode and dual-channel mode. Please note

that the same type and density memory modules are necessary while using dual-

channel DDR, otherwise it may cause system instability.

Please refer to the following table for detailed dual-channel DDR.

Channel A Channel B

Dual-Channel Mode

DIMM1

(Blue)

DIMM2

(Black)

DIMM3

(Blue)

DIMM4

(Black)

System

Density

Two DIMM Symmetrical

Population

9 9

256MB~2GB

Two DIMM Symmetrical

Population

9 9

256MB~2GB

Four DIMM Symmetrical

Population

9

512MB~4GB

Note

1. 9: Installing128MB~1GB Memory modules

2. Symmetrical DIMMs must be identical

- Same DRAM Technology, eg 128M-bit, 256-bit, etc.

- Same DRAM bus width, eg x8 or x16

- Matched Sided DIMMs (Single Sided or Double Sided)

Page is loading ...

Tyan Tomcat i875P S5102 User manual

This manual is also suitable for

Tyan Tomcat i875P S5102 User manual

Related papers

Other documents