Ford 2006 Explorer Owner's manual

Page is loading ...

Introduction

2

Notice To Utility Vehicle and Truck Owners

3

Vehicle Characteristics

4

Driving On Roadways

6

Driving Off-Road

9

Inspecting and Inflating Your Tires

13

Tire Replacement Requirements

15

Loading Your Vehicle

16

Trailer Towing

19

Maintenance and Modifications

20

including photocopying, recording or by any information storage and retrieval

system or translation in whole or part is not permitted without written

authorization from Ford Motor Company. Ford may change the contents without

notice and without incurring obligation.

Table of contents

1

INTRODUCTION

Welcome to Ford Motor Company’s

world of Sport Utility Vehicles

(SUV) and truck driving! Your new

vehicle opens up a completely

different and challenging world of

travel unlike what you have ever

experienced with a conventional car. Most importantly, you’ll be able to

travel with the safety, comfort and dependability of a Ford-built vehicle.

Your vehicle, particularly when loaded, will handle differently than an

ordinary passenger car. This is because your vehicle has special design

and equipment features for cargo-hauling or off-road operation.

Study this supplement and the “Owner’s Guide” for specific information

about equipment features and instructions for safe driving. You must also

learn and understand the capabilities and limitations of your vehicle

through experience. Take it slow and easy until you get to know and

understand your vehicle.

Driving at speeds safe for road conditions and the use of safety belts are

the best means of avoiding the possibility of accident and serious injury.

All occupants must wear the safety belts and children/infants must use

appropriate restraints to minimize the risk of injury or ejection.

Ford Motor Company reserves the right at any time to change

information provided herein, including specifications, design or

testing procedures without incurring obligation.

Introduction

2

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS

Utility vehicles and trucks handle

differently than passenger cars in

the various driving conditions that

are encountered on streets,

highways and off-road. Utility

vehicles and trucks are not designed

for cornering at speeds as high as

passenger cars any more than

low-slung sports cars are designed

to perform satisfactorily under

off-road conditions.

Utility vehicles have a significantly higher rollover rate than

other types of vehicles. To reduce the risk of serious injury or

death from a rollover or other crash you must:

• Avoid sharp turns and abrupt maneuvers;

• Drive at safe speeds for the conditions;

• Keep tires properly inflated;

• Never overload your vehicle; and

• Make sure every passenger is properly restrained.

In a rollover crash, an unbelted person is significantly more likely

to die than a person wearing a seat belt. All occupants must

wear safety belts and children/infants must use appropriate restraints

to minimize the risk of injury or ejection.

Study this supplement and the “Owner’s Guide” for specific information

about equipment features, instructions for safe driving and additional

precautions to reduce the risk of an accident or serious injury.

Notice To Utility Vehicle and Truck Owners

3

VEHICLE CHARACTERISTICS

4WD and AWD Systems

A vehicle equipped with AWD or 4WD (when you select the 4WD mode)

has the ability to use all four wheels to power itself. This increases

traction which may enable you to safely drive over terrain and road

conditions that a conventional two-wheel drive vehicle cannot.

Power is supplied to all four wheels

through a transfer case or power

transfer unit. 4WD vehicles allow

you to select different drive modes

as necessary. Information on shifting

procedures and maintenance can be

found in your “Owner’s Guide.” You

should become thoroughly familiar

with this information before you operate your vehicle.

On some 4WD models, the initial shift from two-wheel drive to 4WD

while the vehicle is moving can cause a momentary clunk and ratcheting

sound. These sounds are normal as the front drivetrain comes up to

speed and is not cause for concern.

Do not become overconfident in the ability of 4WD and AWD

vehicles. Although a 4WD or AWD vehicle may accelerate better

than two-wheel drive vehicle in low traction situations, it won’t stop

any faster than two-wheel drive vehicles. Always drive at a safe speed.

Vehicle Characteristics

4

How your vehicle differs from other vehicles

SUV and trucks can differ from

some other vehicles in a few

noticeable ways. Your vehicle may

be:

• Higher – to allow higher load

carrying capacity and to allow it

to travel over rough terrain

without getting hung up or

damaging underbody components.

• Shorter – to give it the capability

to approach inclines and drive

over the crest of a hill without

getting hung up or damaging

underbody components. All other

things held equal, a shorter

wheelbase may make your vehicle quicker to respond to steering

inputs than a vehicle with a longer wheelbase.

• Narrower — to provide greater

maneuverability in tight spaces,

particularly in off-road use.

As a result of the above dimensional

differences, SUV’s and trucks often

will have a higher center of gravity

and a greater difference in center of

gravity between the loaded and

unloaded condition.

These differences that make your

vehicle so versatile also make it

handle differently than an ordinary

passenger car.

Vehicle Characteristics

5

DRIVING ON ROADWAYS

Vehicles with a higher center of gravity such as utility vehicles

and trucks handle differently than vehicles with a lower center

of gravity. Utility vehicles and trucks are not designed for cornering at

speeds as high as passenger cars any more than low-slung sports cars

are designed to perform satisfactorily under off-road conditions. Avoid

sharp turns, excessive speed or abrupt maneuvers in these vehicles.

Failure to drive cautiously could result in an increased risk of loss of

vehicle control, vehicle rollover, personal injury and death.

Basic operating principles

• Drive slower in strong crosswinds which can affect the normal steering

characteristics of your vehicle.

• Be extremely careful when driving on pavement made slippery by

loose sand, water, gravel, snow or ice.

• Do not use 4WD on dry, hard surfaced roads (except models equipped

with Auto 4WD or AWD). This may damage the drivelines and axles.

If your vehicle goes off the edge of the pavement

• If your vehicle goes off the edge

of the pavement, slow down and

avoid severe brake application or

aggressive steering. Ease the

vehicle back onto the pavement

only after reducing your speed.

Do not turn the steering wheel

too sharply while returning to the

road surface.

• If you have the space, it may be

safer to stay on the apron or

shoulder of the road and slow down gradually before returning to the

pavement. You may lose control if you do not slow down or if you turn

the steering wheel too sharply or abruptly.

• It often may be less risky to strike small inanimate objects, (such as

highway reflectors), and incur minor damage to your vehicle rather

than attempt a sudden return to the pavement which could cause the

vehicle to slide sideways out of control or rollover. Remember, your

safety and the safety of others should be your primary concern.

Driving On Roadways

6

Emergency maneuvers

• In an emergency situation where a sudden sharp turn must be made,

remember to avoid “over-driving” your vehicle, i.e., turn the steering

wheel only as rapidly and as far as required to avoid the emergency.

Avoid abrupt steering, acceleration or braking which could increase

the risk of loss of vehicle control or vehicle rollover. Instead, smooth

variations of the accelerator and/or brake pedal pressure should be

utilized if changes in vehicle speed are called for. Use all available road

surface to return the vehicle to a safe direction of travel.

• In the event of an emergency stop, avoid skidding the tires and do not

attempt any sharp steering wheel movements.

• If the vehicle goes from one type of road surface to another (i.e., from

concrete to gravel), there will be a change in the way the vehicle

responds in steering, acceleration or braking. Again, avoid abrupt

inputs steering or braking inputs.

Snow and ice

Your 4WD or AWD vehicle will have advantages over two-wheel drive

vehicles in snow and on ice by providing increased driving traction.

However, if you suddenly change speed or direction, you may lose

traction and in turn, control as is the case with all vehicles. 4WD and

AWD vehicles can slide on slippery roads just like any other vehicle.

Should the rear end of the vehicle start to slide while cornering on

snowy or icy roads, turn the steering wheel in the direction of the slide

until you regain control. Avoid sudden braking as well. Although a 4WD

or AWD vehicle may accelerate better than a two-wheel drive vehicle in

snow and ice, it won’t stop any faster, because as in two-wheel drive

vehicles, braking occurs at all four wheels. Do not become overconfident

in the ability of 4WD and AWD vehicles to compensate for aggressive

driving maneuvers in poor road conditions.

Make sure you allow sufficient distance between you and other vehicles

for stopping. In emergency stopping situations, avoid locking the wheels.

• For vehicles without anti-lock brakes, use a “squeeze” technique: push

on the brake pedal with a steadily increasing force which allows the

wheels to brake yet continue to roll so that you may steer in the

direction you want to travel. If you lock the wheels, release the brake

pedal and repeat the squeeze technique.

Driving On Roadways

7

• For vehicles with anti-lock brakes, apply and hold the brake firmly. Do

not “pump” the brakes. During hard stopping or stopping on slippery

surfaces, you may feel or hear a pulsing or vibration in the brake

pedal. Do not be alarmed because this is your anti-lock brake system

working. See your “Owner’s Guide” for additional information on the

operation of the anti-lock brake system.

Parking

Before leaving the driver’s seat, make sure that the gearshift is engaged

in P (Park) with an automatic transmission or either 1 (First) or R

(Reverse) with a manual transmission. Set the parking brake fully, shut

off the ignition and remove the key.

Some 4WD vehicles include a Neutral mode. When the transfer case is in

the N (Neutral) position, the engine and transmission are disconnected

from the rest of the driveline. Therefore, the vehicle is free to roll even if

the automatic transmission is in P (Park) or the manual transmission is

in gear.

Do not leave the vehicle unattended with the transfer case in N

(Neutral) position. Always set the parking brake fully and turn

off the ignition when leaving the vehicle. If you do not follow these

precautions your vehicle may move unexpectedly and injure someone.

Driving On Roadways

8

DRIVING OFF-ROAD

“Tread Lightly” is an educational

program designed to increase

public awareness of land-use

regulations and responsibilities in

our nations wilderness areas.

Ford joins the U. S. Forest Service and the Bureau of Land

Management in encouraging you to help preserve our national forest

and other public and private lands by “treading lightly”.

Driving off-road requires good judgment to avoid personal injury and

vehicle damage from concealed objects such as rocks and stumps. Know

the terrain or examine maps of the area before driving off road. Map out

your route before driving in the area. To maintain steering and braking

control of your vehicle, you must have all four wheels on the ground and

they must be rolling, not sliding or spinning. To avoid loss of control,

maintain a firm grip on the steering wheel, especially in rough terrain.

Sudden changes in terrain can result in abrupt steering wheel

motion. To maintain better control and avoid injury to your hand

or wrist, grip the steering wheel from the outside. Do not grip the

spokes.

Driving on sand

When driving over sand, try to keep all four wheels on the most solid

area of the trail. Avoid reducing the tire pressure. Instead, shift to a

lower gear and drive steadily through the terrain. Apply the accelerator

slowly and avoid spinning the wheels.

Avoid reducing tire pressure. Operating your vehicle with below

the recommended tire pressure can increase the risk of loss of

vehicle control, vehicle rollover, personal injury and death. If you

choose to reduce the tire pressure for off-road operation, make sure

you re-inflate the tires as soon as possible.

Avoid excessive speed because vehicle momentum can work against you

and cause the vehicle to become stuck to the point that assistance may

be required from another vehicle. Remember, you may be able to back

out the way you came if you proceed with caution.

Driving Off-Road

9

Driving in mud

Be cautious of sudden changes in vehicle speed or direction when you

are driving in mud. Even 4WD and AWD vehicles can lose traction in

slick mud. As when you are driving over sand, apply the accelerator

slowly and avoid spinning your wheels. If the rear end of the vehicle

does slide while cornering, steer in the direction of the slide until you

regain control of the vehicle.

After driving through mud, clean off residue stuck to rotating tires,

wheels and driveshafts. Excess mud stuck on tires, wheels and rotating

driveshafts causes an imbalance that could damage vehicle components.

Driving through water

Before driving through water,

determine the depth. Avoid water

higher than the center of the wheel

or hubcap. Proceed slowly to avoid

splashing; if the ignition system gets

wet, the vehicle may stall.

Once through water, always try the

brakes. Wet brakes do not stop the

vehicle as effectively as dry brakes. You can dry the brakes faster by

driving the vehicle slowly while applying light pressure on the brake

pedal.

Driving in deep snow

4WD and AWD vehicles are unique in that they can be driven in deep

snow that would stop a conventional two-wheel drive vehicle. Shift to a

low gear and maintain steady pressure on the accelerator. This will help

prevent spinning the wheels while maintaining sufficient momentum to

keep from bogging down. Using tire chains will also help.

Never drive with chains on the front tires of 4WD or AWD vehicles

without also putting them on the rear tires. This could cause the rear of

the vehicle to slide and swing around.

Driving on hills

Operating your vehicle off-road on slopes or hills requires safe

off-road driving practices. Read and follow these safe off-road

driving practices to reduce the risk of loss of vehicle control, vehicle

rollover, serious injury or death.

Driving Off-Road

10

Although natural obstacles may make it necessary to travel diagonally up

or down a hill or steep incline, you should always try to drive straight up

or straight down. Avoid driving crosswise or turning on steep

slopes or hills. A danger lies in losing traction, slipping sideways and

possibly rolling over. Whenever driving on a hill, determine beforehand

the route you will use. Do not drive over the crest of a hill without

seeing what conditions are on the other side. Do not drive in reverse

over a hill without the aid of an observer.

When climbing a steep slope or hill,

start in a lower gear rather than

downshifting to a lower gear from a

higher gear once the ascent has

started. This reduces strain on the

engine and the possibility of stalling.

If you do stall out, do not try to

turn around because you might

induce a rollover. It is better to back

down to a safe location.

Apply just enough power to the

wheels to climb the hill. Too much

power can cause the tires to slip,

spin or lose traction, resulting in

loss of vehicle control.

Descend a hill in the same gear you

would use to climb up the hill to

avoid excessive brake application

and brake overheating. Do not

descend in neutral. Disengage

overdrive or manually shift to a

lower gear. When descending a

steep hill, avoid sudden hard

braking as you could lose control. In

a vehicle without four wheel

anti-lock brakes, if you lock up the

front brakes, the front wheels can’t

roll and if they aren’t rolling, you won’t be able to steer. The front wheels

have to be rolling in order to steer the vehicle. Rapid pumping of the

brake pedal will help you slow the vehicle and still maintain steering

control. If your vehicle has four wheel anti-lock brakes, apply and hold

the brakes firmly. Do not “pump” the brakes.

Driving Off-Road

11

Parking

Before leaving the driver’s seat, make sure that the gearshift is engaged

in P (Park) with an automatic transmission or either 1 (First) or R

(Reverse) with a manual transmission. Set the parking brake fully, shut

off the ignition and remove the key.

Some 4WD vehicles include a Neutral mode. When the transfer case is in

the N (Neutral) position, the engine and transmission are disconnected

from the rest of the driveline. Therefore, the vehicle is free to roll even if

the automatic transmission is in P (Park) or the manual transmission is

in gear.

Do not leave the vehicle unattended with the transfer case in N

(Neutral) position. Always set the parking brake fully and turn

off the ignition when leaving the vehicle. If you do not follow these

precautions your vehicle may move unexpectedly and injure someone.

Driving Off-Road

12

INSPECTING AND INFLATING YOUR TIRES

Safe operation of your vehicle requires that your tires are properly

inflated. Remember that a tire can lose up to half of its air pressure

without appearing flat.

Every day before you drive, check

your tires. If one looks lower than

the others, use a tire gauge to check

pressure of all tires, and adjust if

required.

At least once a month and before long

trips, inspect each tire and check the

tire pressure with a tire gauge

(including spare). Inflate all tires to

the inflation pressure recommended

by Ford Motor Company.

Inspecting your tires

Periodically inspect the tire treads for uneven or excessive wear and

remove stones, nails, glass or other objects that may be wedged in the

tread grooves. Check for holes or cuts that may permit air leakage from

the tire and make necessary repairs.

Also inspect the tire sidewalls for cuts, bruises and other damage. If

internal damage to the tire is suspected, have the tire demounted and

inspected in case it needs to be repaired or replaced. For your safety,

tires that are damaged should not be used because they are more likely

to blow out or fail. Tires can be damaged during off-road use, so

inspection after off-road use is also recommended.

Inflating Your Tires

Use a tire gauge to check the tire inflation pressure, including the spare,

at least monthly and before long trips. You are strongly urged to buy a

reliable tire pressure gauge, as automatic service station gauges may be

inaccurate. Ford recommends the use of a digital or dial type tire

pressure gauge rather than a stick type tire pressure gauge.

Always inflate your tires to the Ford recommended inflation pressure

even if it is less than the maximum inflation pressure information found

on the tire. The Ford recommended tire inflation pressure is found on

the tire and loading information label or certification label attached to

the left front door lock facing or door latch post pillar. Failure to follow

tire pressure recommendations can cause uneven treadwear patterns and

adversely affect the way your vehicle handles.

Inspecting and Inflating Your Tires

13

Maximum Permissible Inflation Pressure

Tire manufactures maximum permissible pressure and/or the pressure at

which the maximum load can be carried by the tire. This pressure is

normally higher than the manufacturer’s recommended cold inflation

pressure which can be found on either the tire label or certification label

which is located on the structure by the trailing edge of the driver’s door

or the edge of the driver’s door. The cold inflation pressure should never

be set lower than the recommended pressure on the vehicle

label.

Note: You may not find this information on all tires because it is not

required by federal law.

The tire suppliers may have additional markings, notes or warnings such

as standard load, radial tubeless, etc.

Tires can slowly lose pressure due to normal use or due to changes in

weather. For example, a 10 degree temperature drop can cause a

corresponding drop of 7 kPa (1 psi) in tire inflation pressure.

Maintain proper tire inflation pressure. Under-inflation is the

most common cause of tire failures. Under-inflation increases

sidewall flexing and rolling resistance, resulting in heat buildup and

internal damage to the tire. Operating your vehicle with under-inflated

tires may result in severe tire cracking, tread separation or tire

“blowout”, which can lead to loss of vehicle control, vehicle rollover,

serious injury or death.

The Ford recommended inflation pressure is based on cold tire pressure.

Tire pressure increases even after driving short distances, so try to check

tire inflation pressures before driving. If you are checking tire pressure

when the tire is hot, (i.e. driven more than 1.6 km [1mile]), never “bleed”

or reduce air pressure. A hot tire with a tire pressure at or below

recommended cold inflation pressure could be significantly under-inflated.

To check the pressure in your tire(s):

1. Make sure the tires are cool, meaning they are not hot from driving

even a mile.

Note: If you have to drive a distance to get air for your tire(s), check

and record the tire pressure first and add the appropriate air pressure

when you get to the pump. It is normal for tires to heat up and the air

pressure inside to go up as you drive. Never “bleed” or reduce air

pressure when tires are hot.

2. Remove the cap from the valve on one tire, then firmly press the tire

gauge onto the valve.

Inspecting and Inflating Your Tires

14

3. Add air to reach the Ford recommended air pressure.

Note: If you overfill the tire, release air by pushing on the metal stem in

the center of the valve. Then recheck the pressure with your tire gauge.

4. Replace the valve cap.

5. Repeat this procedure for each tire, including the spare.

Note: Some spare tires require higher inflation pressure than the other tires.

6. Visually inspect the tires to make sure there are no nails or other objects

embedded that could poke a hole in the tire and cause an air leak.

7. Check the sidewalls to make sure there are no gouges, cuts, bulges or

other irregularities.

TIRE REPLACEMENT REQUIREMENTS

Your vehicle is equipped with tires designed to provide safe ride and

handling capability.

Only use replacement tires and wheels that are the same size

and type (such as P-metric versus LT-metric or all-season versus

all-terrain) as those originally provided by Ford. Use of any tire or

wheel not recommended by Ford can affect the safety and

performance of your vehicle, which could result in an increased risk of

loss of vehicle control, vehicle rollover, personal injury and death.

Additionally the use of non-recommended tires and wheels could cause

steering, suspension, axle or transfer case/power transfer unit failure.

See your Owner Guide for additional information. If you have questions

regarding tire replacement, see an authorized Ford or Lincoln/Mercury

dealer.

Make sure all tires and wheels on the vehicle are of the same size, type,

tread design, brand, load-carrying capacity and speed rating because it

can affect the safety and performance of your vehicle, which could result

in an increased risk of loss of vehicle control, vehicle rollover, personal

injury and death.

Tire Replacement Requirements

15

LOADING YOUR VEHICLE

Passenger and cargo load limits

The combined weight of all occupants and all cargo (including added

accessories) must not exceed the maximum payload for your vehicle.

The maximum payload for your vehicle can be found on the tire label on

the driver’s door or door pillar. Look for statement “THE COMBINED

WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX

KG OR XXX LBS” to determine your vehicle’s maximum payload.

The appropriate loading capacity of your vehicle can be limited

either by volume capacity (how much space is available) or by

payload capacity (how much weight the vehicle should carry). Once

you have reached the maximum payload of your vehicle, do not add

more cargo, even if there is space available. Overloading or improperly

loading your vehicle can contribute to loss of vehicle control and

vehicle rollover.

In addition to maximum payload, additional loading terms and weight

ratings are very important, particularly when towing a trailer or when a

heavy accessory such as a snowplow has been added to the vehicle.

Other terms related to loading include base curb weight, gross vehicle

weight rating (GVWR), gross axle weight rating (GAWR), gross

combined weight rating (GCWR). Refer to your “Owner’s Guide” for

additional information regarding these terms and maximum safe weight

limits.

Effects of improperly loading or overloading your vehicle

Improper weight distribution and exceeding the maximum payload can

have serious consequences in terms of passenger safety, including

damage to the suspension system, springs, and shock absorbers, reduced

braking capability, handling or steering problems, irregular tire wear, tire

failure or other damage.

Loaded vehicles, with a higher center of gravity, may handle

differently than unloaded vehicles. Do not overload your vehicle

and use extra precautions, such as driving at slower speeds, avoiding

abrupt steering changes and allowing for increased stopping distance,

when driving a heavily loaded vehicle. Over loading or loading the

vehicle improperly can deteriorate handling capability and contribute

to loss of vehicle control and vehicle rollover.

Loading Your Vehicle

16

Loading and securing cargo

When using your vehicle to haul

cargo, make sure it is properly

loaded to help ensure safe handling

of the vehicle. You should tie down

or restrain items in the cargo area

so that they will not come loose and

create the risk of injury in a crash.

Cargo should be evenly distributed

over the floor of the cargo area,

with the heaviest cargo on the

bottom and ahead of the rear axle.

Do not allow people to ride in the cargo area of your vehicle.

People who are not riding in seats with their safety belts

fastened are much more likely to be injured or killed in a collision.

Loading cargo on the roof

Cargo placed on the roof will tend to make your vehicle more top heavy,

causing it to lean more in corners and creating a greater possibility of

vehicle rollover. If you must haul cargo on the roof of the vehicle, use

extra caution when loading the vehicle and when driving. Cargo on the

roof rack should be properly secured and evenly distributed over the

roof rack area, with the heaviest cargo on the bottom, near the front of

the roof rack area. Any load placed on the roof rack should not exceed

the maximum load shown on the roof rack’s label.

Truck camper loading

When the vehicle is used to carry a slide-in camper, the total cargo load

of the truck consists of the manufacturer’s camper weight figure, the

weight of installed additional camper equipment not included in the

manufacturer’s camper weight figure, the weight of the camper cargo,

and the weight of all the passengers and cargo in your vehicle.

Loading Your Vehicle

17

The total cargo load should not exceed the truck’s cargo weight rating

and the camper’s center of gravity should fall within the trucks’s

recommended center of gravity zone when installed. For more

information refer to your truck camper loading label.

Do not allow people to ride in a slide-in camper. People who are

not riding in seats with their safety belts fastened are much

more likely to be injured or killed in a collision.

Loading Your Vehicle

18

TRAILER TOWING

Your vehicle may be equipped for towing trailers (or may require a trailer

tow package). Before you operate your vehicle with a trailer, make sure

that you comply with the guidelines in the “RV & Trailer Towing Guide”.

The combined total weight of the vehicle and trailer must be less than or

equal to the recommended Gross Combination Weight Rating (GCWR)

and be properly balanced and secured. Refer to “RV & Trailer Towing

Guide,” the “Owner’s Guide” or see an authorized Ford or

Lincoln/Mercury Dealer for additional information.

Trailer Towing

19

MAINTENANCE AND MODIFICATIONS

The suspension and steering systems on your vehicle have been carefully

designed to provide safe, predictable performance and durable load

carrying capability. Do not make modifications such as adding or

removing parts (such as lift kits or stabilizer bars) or using replacement

parts not equivalent to the original factory equipment because these

modifications can affect the safety of your vehicle.

Do not use “aftermarket lift kits” or other suspension

modifications. “Aftermarket lift kits” could adversely affect the

vehicle’s handling characteristics, which could result in an increased

risk of loss of vehicle control, vehicle rollover, personal injury and

death.

Any modifications to a vehicle that raise the center of gravity can make

it easier to induce vehicle rollover. Ford recommends that you take extra

precautions, such as driving at lower speeds, avoiding abrupt steering

changes and allowing for increased stopping distance, for any vehicle

equipped with a high load (for example, roof racks).

Failure to maintain your vehicle properly may void the warranty, increase

your repair cost, reduce vehicle performance and operational capabilities

and adversely affect driver and passenger safety. Frequent inspection of

vehicle chassis and powertrain components is recommended if the

vehicle is subjected to heavy off-road usage. Refer to the “Owner’s

Guide” and “Service Guide” for proper maintenance instructions and

schedules.

Maintenance and Modifications

20

Page is loading ...

Ford 2006 Explorer Owner's manual

Ford 2006 Explorer Owner's manual

in other languages

Related papers

Other documents