Swingline 1757571 User manual

To register this product go to www.swingline.com

Pour enregistrer ce produit allez sur www.swingline.com

Para registrar este producto vaís en www.swingline.com

Swingline

™

Stack-and-Shred

™

100X Shredder

Auto+

™

Technology

Déchiqueteuse

Swingline

™

Stack-and-Shred

™

100X

à technologie

Auto+

™

Swingline

™

Stack-and-Shred

™

100X Destructora

de papel

Tecnología Auto+

™

Instruction Manual

Manuel d’utilisation

Manual de instrucciones

Page is loading ...

Introduction

Thank you for choosing this shredder from ACCO. We are sure

it will serve you well, but please take a little time to study these

instructions to ensure you get the best out of your machine.

Decal Panel (B)

• Paper Jam indicator – This means there is a Paper Jam

• Bin full / loading door open indicator – This means

the bin is full or open or the loading door is open

• Cool down indicator – This means the machine is

cooling down

Description of product parts

A

On/off switch (at rear of machine)

B

Important safety symbols

C

Manual entry slot

D

Credit card slot

E

Auto/Standby button

F

Reverse button

G

Continuous Jam Boost button

H

Loading door button

I

Loading door/lid

J

Paper stack viewing window

K

Bin full/Door open, Cool down and Paper Jam indicators

L

Pull out bin with viewing window

M

Autofeed chamber

N

Interlock actuator switch

Speciﬁcations

Sheet capacity

(Manual Entry Slot C)

Sheet capacity

(Autofeed chamber M)

Auto Shutdown

Duty cycle

Run time from cold

Volts / Hz

Amperage

Motor watts

Swingline 100X Shredder

6 sheets (75gsm)

100 sheets (75gsm)

After 2 minutes

5min ON / 30min OFF

10 minutes

120V / 60Hz

1.8 amps

200 watts

Shredder Control Panel

This means read instructions before use.

This means do not use any aerosol sprays.

This means you should be careful because long hair can

become entangled in the cutting head.

This means don’t reach into the feed opening of the

cutting head.

This means be careful of ties and other loose clothing

which could become entangled in the cutting head.

This means keep children away from shredder.

This means be careful of loose jewelry which could

become entangled in the cutting head.

This means do not shred CD/DVD.

This means do not use any oil lubricant.

ReverseForwardAuto

Important Safety Symbols

Safety First

To guard against injury, the following basic safety precautions

must be observed in the setup and use of this product.

• Electrical shock hazard. Do not open. No user serviceable

parts inside.

• Do not operate the shredder near children and pets.

• Do not use aerosol dusters or cleaners.

• Do not spray anything into the shredder.

• Do not use near water.

• Do not alter the attachment plug. The plug is congured for the

appropriate electrical supply.

• Do not operate with a damaged power supply cord or plug,

after it malfunctions, or after it has been damaged in any

manner.

• The socket-outlet should be installed near the equipment and

shall be easily accessible.

• Do not overload electrical outlets beyond capacity as this can

result in re or electrical shock.

• Unplug your shredder before moving it or when it is not in use

for an extended period of time.

• Ensure the machine is plugged into an easily accessible power

outlet, and ensure the cable is not likely to trip up a passer by.

There is an interlock actuator switch (N) located on the left of

the internal loading bay (see Fig. 4) which is designed to prevent

the shredder from operating when the loading door is open. You

must NOT under any circumstances tamper with this interlock

actuator switch. You must NOT insert any object into the interlock

actuator switch other than the interlock actuator pin on the

loading door, as to do so could activate the cutter blades.

Any attempt to repair this unit by unqualied personnel will

invalidate the warranty. Please return to supplier.

3

4

20lb / 80gsm paper

- Letter - 8.5" x 11"

- Legal - Single sheet folded in half

- A4 - 210mm x 297mm

- A5 - 148mm x 210mm

- A3 - Single sheet folded in half

1" (26 mm) and ¼" (6 mm) or smaller staples.

NOT suitable for heavy duty staples

above this size

NOT suitable for stapled documents

> 25 sheets

Capable of shredding small/medium

(max wire thickness = 0.03"/0.9 mm) paper

clips, < 0.25"/32mm length

NOT suitable for clipped documents

> 25 sheets

Paper type Staples Paper Clips

The 100X can handle the following…

100X Shredding Capability

OK to shred:

Do not shred:

The Swingline Stack and Shred

(100X) accepts fastened sheets,

however, to extend the life of

your product we recommend

that staples and paper clips be

removed prior to shredding.

- Stapled paper within 1"/

25mm from any corner

- Paper clip paper within 1"/

25mm from any corner

- Single folded sheets

- 100 sheets single side

color printed paper

- Credit cards

(through credit card slot)

- 20-50lb/80-100gsm paper

(through manual entry slot)

- 100 sheets plain paper - 100 sheets single side

printed paper

Document edge bound by

staples and paperclips

OTHER ITEMS INCLUDE:

Laminated documents

Adhesive Labels Plastic folders

Double sided color

printed paper

>25 sheets stapled or paper

clipped documents

Glossy paper

1.25"

>

¼"

>

1"

✓

✗

Auto+

™

Technology

The 100X has been designed to automatically shred up to 100 sheets from the autofeed chamber and up to 6 sheets through the

manual slot. The patent pending autofeed mechanism has been designed to handle paper fastened with staples and paper clips and

to only pull a few sheets of paper into the cutting mechanism to minimise the risk of paper jams. The stack of paper does not need to

be prearranged before loading into the chamber.

To load the shredder, simply press the loading door button which automatically opens the loading door to a 45 degree angle and insert

documents. You can open the door further to 90 degrees for easier access if required. Closing the loading door will automatically start

the shredding cycle.

Fig. 1

Autofeed

Fig. 2

Manual feed

Fig. 3

Credit card

Fig. 4

Safety device

If the 100X is used continuously for over 10 minutes the

shredder may overheat and the thermometer symbol will

illuminate . Please allow the shredder to cool down. When

the shredder is ready to be used the thermometer symbol

will no longer be illuminated. If the shredder needs to cool

down while shredding, no action is needed. The shredder will

automatically restart shredding paper once it has cooled down

after periods of continuous use. All you need to do is ensure

paper is loaded into the chamber and the bin is not full when

the machine is cooling down.

Over Heating

Auto Paper Jam Bin full / Cool down

bin open /

loading

door open

Color of symbol Blue Red Red Red

Power OFF Mode Off

Auto Mode Light

Continuous Jam Boost Mode Light Light

Reverse Mode Light Light

Paper Jam Light Light

Loading Door open Light Light

Bin full or open Light Light

Motor Cool Down Required Light Light Flashing

Self cleaning of cutters Light Flashing

Sleep Mode Off

5

Lights and Icons Explained

Automatic Shredding (Fig. 1)

Press the loading door button (H) to open the loading door.

Load up to 100 sheets at a time into the autofeed chamber

(M). Do not ll above the 100 MAX level (see inside front right

of loading bay) this could damage the shredder.

Close the loading door without pressing the loading door

button. The shredder will now start automatically.

Manual Shredding (Fig. 2)

If you only have up to 6 sheets to shred, you can use the

manual entry slot (C), provided the autofeed chamber

is empty.

Credit Card Shredding (Fig. 3)

100X can shred credit cards. Switch the shredder to auto

mode (see #4 under “Operation”). Insert the credit card

into the opening on top of the manual entry slot (C). ACCO

encourages customers to recycle shredded paper. Please note

that sometimes shredded paper cannot be recycled if mixed

with credit card shards. If recycling, please separate shredded

paper and credit cards

Operation

➊ After unpacking the product, pull out the shredder bin (L).

Remove and t the recyclable paper bag (as per instructions

printed on the bag).

➋ Connect the shredder to power supply.

➌ Ensure the on/off button (A) on the back of the machine is

in the on position.

➍ To start shredding, press the central Auto button (E). This

will illuminate the blue standby symbol on the auto button.

This sets the shredder into auto mode. You are now ready

to shred.

➎ If the shredder is left in auto mode for more than 2 minutes

without being used, it will automatically turn to standby

mode to save power.

➏ The shredder will automatically operate from standby mode

when paper is inserted into the manual entry slot. Opening

either the loading door/lid (I), pull-out bin (L) or pressing

any button will return the product to auto mode.

Rare Occasions of Jamming

In the unlikely event of the shredder jamming, the 100X will

automatically reverse and forward the engine three times

to clear a jam. If after this auto jam clearance cycle the shred-

der still has a paper jam, the jam indicator will continue to

illuminate . Try clearing the jam using the reverse (F) and

continuous jam boost (G) buttons. If this is unsuccessful, open

the loading door (I), remove the remaining stack of paper,

then pull the jammed paper free of the cutting mechanism.

Bin/Loading Door Open

Protection Function (Fig. 4)

As an added precaution, if the bin or loading door is opened

during shredding, the shredder will stop, and the bin full / door

open indicator will glow red .

There is an interlock actuator switch (N) located on the left

of the internal loading bay which is designed to prevent the

shredder from operating when the loading door is open. You

must NOT under any circumstances tamper with this interlock

actuator switch. You must NOT insert any object into the

interlock actuator switch other than the interlock actuator

pin on the loading door, as to do so could activate the cutter

blades.

6

Bin Full

The shredder will not function when the bin is full and the bin

full symbol is illuminated red. You should empty the bin.

• Pull open the bin

• Never try to reach for any shreds hanging from cutters

• Empty bin and replace shredder bag if you are using one

• Push the empty bin back into place and press the auto button

to resume shredding.

Self-cleaning Cutters

After emptying and replacing a full bin, the shredder will run in

forward and reverse for 10-18 seconds to clear any remaining

paper from the cutter mechanism. This unique ‘self-cleaning’

mechanism is additional jam prevention technology from

Swingline.

Lubrication of the Shredder

ACCO Brands accepts no liability for product performance or

safety when lubricants are used on any part(s) of this machine.

Do not oil any part of the shredder.

The rollers on the auto-feed mechanism may become dirty over

time, please wipe clean with a dry cloth to maintain maximum

product performance.

Do not use any aerosols or sprays to either oil or clean the

shredder.

Protection Features

Protection features on the 100X include:

➊ Enclosed cutters are inside the Autofeed chamber (M) so

they are isolated from outside surfaces when in operation.

➋ Interlock switches that shut off power to the cutters when

either the loading door/lid (I) pull-out bin (L) or both are

open.

➌ Curved paper entry path for manual entry slot (C) to

reduce chances of cutters “grabbing” paper.

Reverse Function

➊ Should you wish to reverse paper out while shredding,

a reverse button ( ) has been provided for your

convenience. The jam indicator will turn to red while using

reverse mode.

➋ The reverse function will only run when the button is being

pressed. When the reverse button is released the shredder

will revert to auto mode.

Shredder Accessories

and Maintenance

We recommend using a paper bag for recycling shredded

paper. Our paper bags are made from 80% post-consumer

recycled material and are fully recyclable.

Accessory Part Number

Recycling Paper Bag 1765026

7

Warranty

Limited 5 year Cutter Warranty for 100X Shredder and

Limited 2 Year Warranty for all other Parts

ACCO Brands USA LLC, 300 Tower Parkway, Lincolnshire, IL 60069 (in Canada,

ACCO Brands Canada Inc., 5 Precidio Court, Brampton, ON L6S-6B7; and in Mexico,

ACCO Mexicana, S.A. de C.V. Av. Circuito Industrial Norte #6 Parque Industrial Lerma

52000, Lerma Edo. De México) (each, respectively, “ACCO Brands”) warrants to the

original purchaser that the cutters of this Swingline ™ Shredder 100X are free from

defects in workmanship and material under normal use and service for a period of

5 years after purchase and all other parts are free from defects in workmanship and

material under normal use and service for a period of 2 years after purchase.

ACCO Brands’ obligation under this warranty is limited to replacement or repair, at

ACCO Brands’ option, of any warranted part found defective by ACCO Brands without

charge for material or labor. Any replacement, at ACCO Brands’ option, may be the

same product or a substantially similar product that may contain remanufactured or

refurbished parts. This warranty shall be void in the following circumstances:

(i) if the product has been misused,

(ii) if the product has been damaged by negligence or accident, or

(iii) if the product has been altered by anyone other than ACCO Brands or ACCO

Brands’ authorized agents.

For warranty execution, please call:

1-800-541-0094 in the USA

1-800-263-1063 in Canada

1-800-758-6825 in Mexico

Or go to www.swingline.com.

TO THE EXTENT ALLOWED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU

OF ALL OTHER EXPRESSED WARRANTIES. REPRESENTATIONS OR PROMISES

INCONSISTENT WITH OR IN ADDITION TO THIS WARRANTY ARE UNAUTHORIZED

AND SHALL NOT BE BINDING ON ACCO BRANDS. TO THE EXTENT PERMITTED

BY APPLICABLE LAWS, ANY IMPLIED WARRANTIES (IF APPLICABLE) ARE

LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. SOME STATES

AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED

WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. TO THE

EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ACCO BRANDS BE

LIABLE FOR ANY SPECIAL, INCIDENTAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL

OR SIMILAR DAMAGES, WHETHER OR NOT FORSEEABLE. SOME STATES AND

JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF SPECIAL,

INCIDENTAL, PUNITIVE, EXEMLARY, CONSEQUENTIAL, OR SIMILAR DAMAGES, SO

THE ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.

FOR CONSUMERS WHO HAVE THE BENEFIT OF CONSUMER PROTECTION LAWS OR

REGULATIONS IN THEIR JURISDICTION OF PURCHASE OR, IF DIFFERENT, IN THEIR

JURISDICTION OF RESIDENCE, THE BENEFITS CONFERRED BY THIS WARRANTY

ARE IN ADDITION TO ALL RIGHTS AND REMEDIES CONVEYED BY SUCH CONSUMER

PROTECTION LAWS AND REGULATIONS.

To the extent permitted by law, this warranty is not transferable and will automatically

terminate if the original product purchaser sells or otherwise disposes of the product.

This warranty gives you specic legal rights. Other rights, which vary from

jurisdiction to jurisdiction, may exist. In addition some jurisdictions do not allow (i)

the exclusion of certain warranties, (ii) limitations on how long an implied warranty

lasts and/or (iii) the exclusion or limitation of certain types of costs and/or damages,

so the above limitations may not apply.

8

TM/MC

APPLICABLE MACHINES

QUESTION ANSWER

60X 80X 100X 250X 500X

1 The shredder will not

start.

a

Check power switch on the back of the machine is turned on. (

)

Y Y Y Y Y

b

Check that the Auto button (

) has been pressed or the switch

is in the Auto position and the power switch on the back has been

turned on.

Note: The Auto button light turns off after 2 mins of non-use.

The shredder wakes up automatically if paper is in the autofeed

chamber or fed into the manual feed slot

Y Y Y

c Is the “bin door/ loading door open” indicator light red

(

)? Make sure both the loading door and the bin door are

closed.

Y Y Y Y

2 There are documents in

the autofeed chamber

but the shredder has

stopped running.

a

Is the cool-down indicator light red (

)? If so, allow the shredder

to cool down. Shredding will resume automatically after the

shredder has cooled down.

Y Y Y Y

b If the “bin door/ loading door open/bin full” indicator light is red

(

), empty the bin. Also check to see if the loading door and

bin doors are closed. Shredding will resume automatically.

Y Y Y Y

c

Is the jam indicator light red (

)? If so, the shredder was unable

to clear a jam even after the automatic jam clearance cycle. Use the

manual reverse button (

) to back out paper from the cutters.

Open the lid and remove the offending papers.

Y Y Y Y

d If there are crumpled sheets in the stack, they may not feed

properly. It is recommended that you feed them through the manual

feed slot.

Y Y Y Y Y

e If there are multiple folded sheets in the stack, unfold the sheets

before placing them back in the stack or feed through the manual

feed slot.

Y Y Y Y Y

f If there are unopened envelopes in the stack, remove them, open

the envelopes and lay the contents ﬂat into the autofeed chamber,

unfolding any folded sheets. Envelopes can be shredded through

the manual feed slot.

Y Y Y Y Y

g Examine the rollers, if they are covered with paper dust, clean them

with a dry cloth.

Y Y Y Y Y

FOR ADDITIONAL INFORMATION ON WHAT TO SHRED THROUGH AUTO FEED AND WHAT TO SHRED

VIA MANUAL FEED SLOT, PLEASE SEE SECTION IN THE MANUAL ON ‘SHREDDING CAPABILITY’

Troubleshooting Guide for Stack-and-Shred

™

100X

Tel. 800-541-0094

www.acco.com/service

www.swingline.com/shredders

APPLICABLE MACHINES

QUESTION ANSWER

60X 80X 100X 250X 500X

3 There isn’t any paper

in the shredder but it

won’t stop running.

a The auto-start infra-red sensor, located in the paper feed entry-

slot, can occasionally become covered in paper-dust causing the

shredder to run despite no paper being fed into the machine. Switch

the shredder off at the rear of the machine and carefully clean the

sensor using a cotton-swab (see g 6).

Y Y Y Y Y

b If the shredder still does not stop running, call ACCO at:

800-541-0094

Y Y Y Y Y

4 Every time I shut the

bin, the shredder turns

itself on automatically

for a few seconds.

a After the bin is removed and replaced, the shredder will run for

approximately 8 seconds to clear away any remaining paper from

the cutter mechanism.

Y Y Y Y

5 I have to feed the paper

quite a long way into

the manual feed slot

before it engages with

the cutting mechanism

a Unlike conventional shredders, the paper needs to pass through the

autofeed chamber before the paper meets

the cutting mechanism. For this reason, the manual feed slot has

been designed to be extremely easy to slide paper into.

Y Y Y Y Y

6 I have locked the

shredder but there is

a paper jam and my

sensitive documents

are still in the machine

a Enter your PIN to unlock the loading door and clear the jam. If you

have forgotten the code or you have left the shredder to continue

your working day, the machine will open automatically after 30

minutes of inactivity. After clearing the jam, reload the shredder

before locking the loading door again.

Y Y

Do I need to enter the

same four digits, as a

locking PIN, each time I

use the shredder?

b No. The shredder will register the four digit PIN code each time so

you could change your PIN number every time you use the shredder.

Y Y

I have just realized that

I have some documents

in the autofeed

chamber that I don’t

want to shred but the

loading door is locked.

c Re-entering your four digit PIN code unlocks the paper loading door.

Y Y

What happens if

someone tries to

guess my PIN code

to get access to my

documents?

d After 5 incorrect attempts to enter the code the locking mechanism

will not accept any more entries. The loading door will remain

locked until the shredding is complete. Y Y

7 How should I maintain

my shredder?

a Use Swingline oil sheets to lubricate the cutting head, do not use

other types/brands of oil

Y Y Y Y

b Clean the auto-start infra red sensor on a regular basis

(see point 3a).

Y Y Y Y Y

c Clean rollers free of any paper dust with a dry cloth Y Y Y Y Y

9

Page is loading ...

Service

ACCO Brands USA

300 Tower Parkway,

Lincolnshire, IL 60069-3640

(800) 541-0094

ACCO Brands Canada

5 Precidio Court,

Brampton, ON L6S-6B7

(800) 263-1063

Auto+ Technology™, and Autofeed Chamber™ are trademarks of ACCO Brands.

Auto + Technology ™, et Autofeed Chambre ™ sont des marques déposées d’ACCO Brands.

Stack-y-Shred ™, Auto + ™ Tecnología, y Autofeed Cámara ™ son marcas registradas

de ACCO Brands.

04713P001R2 1111

ACCO Mexicana

S.A. de C.V. Av.

Circuito Indusrial Norte #6

Parque Industrial Lerma 52000,

Lerma Edo. De México

800-758-6825

FCC Class B Notice - Notication pour les Etats-Unis

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorientorrelocatethereceivingantenna.

• Increasetheseparationbetweentheequipmentandreceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.

• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.

Canada Class B Notice - Avis Canada, Classe B

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Modications:

Any modiﬁcations made to this device that are not approved by ACCO Brands Corporation may void the authority granted to the user by the FCC

and/or by Industry Canada to operate this equipment.

Toutes modiﬁcations apportées à ce dispositif et non approuvées par ACCO Brands Corporation annuleront le droit accordé à l’utilisateur par le FCC

et/ou par Industrie Canada de faire fonctionner cet équipement.

ACCO Brands

300 Tower Parkway

Lincolnshire, IL 60069-3640

In USA call 800.541.0094

www.acco.com

www.swingline.com

Swingline 1757571, Stack-and-Shred, STACK-AND-SHRED 100X User manual

Related papers

Other documents