Modine Manufacturing BDP150 Installation guide

Brand: Modine Manufacturing

Model: BDP150

Type: Installation guide

75-506.10

5H0703190000

INSTALLATION INSTRUCTIONS

vertical air deflector blades

gas, electric and oil-fired unit heaters

April, 2017

1. Remove existing screws at the top and bottom of the air

discharge opening. (For oil-fired models, screws are

furnished in kit.)

2. Place the mounting flanges (item #2) so that the

indentations for the punched holes face each other, and

attach with the screws removed in step 1.

3. Insert the support rod (item #3) through the holes provided

in the mounting flanges. Secure this support rod with the

acorn push nuts (item #5) provided.

4. Assemble the coil spring (item #4) provided to the straight

end of each deflector blade (item #1) and insert the ends of

the blades with the coil springs into holes in mounting

flanges. Push on the deflector blade until the beveded end

slips into the holes of the opposite mounting flange.

5. Adjust deflector blades to obtain desired direction of heat

throw.

For:

Gas Models PDP150 - PDP/BDP400

Electric Models HER30 - 250

Oil Models POR100 - POR185

*NOTE: DO NOT OPERATE UNIT WITH DEFLECTOR BLADES IN A CLOSED POSITION.

As Modine Manufacturing Company has a continuous products improvement program, it reserves the right to change design and

specifications without notice.

page 1 of 2

1. Remove existing screws at the top and bottom of the right

hand air discharge opening.

2. Place the mounting flanges (item #2) so that the

indentations of the punched holes face each other, and

attach with the screws removed in step 1.

3. Insert the support rods (item #3) through the holes provided

in the mounting flanges. Secure these support rods with the

acorn push nuts (item #5) provided.

4. Assemble the coil springs (item #4) provided to the straight

end of each deflector blade (item #1) and insert the ends of

the blades with the coil springs into holes in the mounting

flanges. Push down on deflector blade until the beveled end

slips into the holes of the opposite mounting flange.

5. Repeat the same procedure for the left hand air discharge

opening.

6. Adjust deflector blades to obtain desired direction of heat

throw.

HER30 - HER50 32493 3H0261960043 6 2 1 6 2 -

HER50 - HER150 32488 3H0261960002 6 2 1 6 2 -

HER200 & 250 32489 3H0261960004 6 2 1 6 2 -

PDP/BDP150 78550 3H0261960005 6 2 1 6 2 -

PD/PDP/PDE/BDP175 78553 3H0261960006 6 2 1 6 2 -

PDP/BDP200 & 250 78556 3H0261960007 8 2 3 8 6 -

PD/PDP/PDE/BDP300 78559 3H0261960008 8 2 3 8 6 -

PDP/BDP350 78562 3H0261960010 10 4 4 10 8 -

PDP/BDP400 78565 3H0261960011 10 4 4 10 8 -

POR100 - 145 16412 3H0261960013 6 2 2 6 4 8

POR185 16415 3H0261960014 8 2 2 8 4 8

Modine Manufacturing Company • 1500 DeKoven Avenue • Racine, Wisconsin 53403-2552

Tel: 1.800.828.4328 (HEAT) • Fax: 262.636.1665 • www.modine.com

Part and Quantity

Unit Deflector Mounting Support Coil Push Metal

Model Item Kit Part Blade Flange Rod Spring Nut Screw

No. Code Number ➀ ➁ ➂ ➃ ➄ ➅

page 2 of 2

Modine Manufacturing BDP150 Installation guide

Modine Manufacturing BDP150 Installation guide

Modine Manufacturing BDP150 Installation guide

Related papers

Other documents