Kohler K-8300-KS-NA Dimensions Guide

Kohler
Brand
Kohler
Model
K-8300-KS-NA
Category
Faucets
Type
Dimensions Guide

Kohler K-8300-KS-NA is a valve body rough-in designed for use in standard, back to back and thin wall installations. It includes a valve body, rough-in guide, and test cap. The 1/2" Universal NPT & direct sweat inlets & outlets, with stops, and service stops include integral check valves. The valve body features integral mounting locations and symmetrical valve inlets to simplify installation. The rough-in guide is designed for both standard and thin wall installations.

Kohler K-8300-KS-NA is a valve body rough-in designed for use in standard, back to back and thin wall installations. It includes a valve body, rough-in guide, and test cap. The 1/2" Universal NPT & direct sweat inlets & outlets, with stops, and service stops include integral check valves. The valve body features integral mounting locations and symmetrical valve inlets to simplify installation. The rough-in guide is designed for both standard and thin wall installations.

Features
•
Includes valve body, rough-in guide and test cap
•
1/2" Universal NPT & direct sweat inlets & outlets, with stops
•
Service stops include integral check valves
•
Requires valve cartridge and trim to complete installation (sold
separately).
Material
•
Forged De-zincification Resistant Brass body provides long
term reliability and resistance to aggressive water conditions
Installation
•
Designed for use in standard, back to back and thin wall
installations
•
Valve body features integral mounting locations and symmetrical
valve inlets to simplify installation
Codes/Standards
ASME A112.18.1/CSA B125.1
•
Rough-in guide designed for both standard and thin wall
installations
KOHLER
®
Faucet Lifetime Limited
Warranty
•
Installed valve rough-in can be flushed and pressure tested to
150psi max (air or water) without cartridge, using K-10351 Test
Cap (supplied)
See website for detailed warranty information.
Required Accessories
K-8305/K-P8305 Series Rite-Temp® Cartridges
1-800-4KOHLER (1-800-456-4537)
Kohler Co. reserves the right to make revisions without notice to product specifications.
For the most current Specification Sheet, go to www.kohler.com.
9-28-2018 14:53
Rite-Temp
®
Valve Body Rough-In
K-8300-KS
Cutout for finished walls
Notes
Technical Information
Install this product according to the installation
guide.
All product dimensions are nominal.
Avoid cross-flow conditions. Do not install shut-off
device on either valve outlet.
Cap the shower outlet if deck-mount spout,
diverter, or handshower is connected to the spout
outlet.
Install straight pipe or tube drop of 7" (178 mm)
to 18" (457 mm) with single elbow between the
valve and wall-mount spout.
For finished walls greater than 3/4" (19 mm) and
less than 1-1/2" (38 mm), install support(s) 2" (51
mm) from the stud face.
For finished walls greater than 1-1/2" (38 mm),
install support(s) 3" (76 mm) from the face of the
finished wall.
1-800-4KOHLER (1-800-456-4537)
Kohler Co. reserves the right to make revisions without notice to product specifications.
For the most current Specification Sheet, go to www.kohler.com.
9-28-2018 14:53
Rite-Temp
®
Valve Body Rough-In
K-8300-KS
  • Page 1 1
  • Page 2 2

Kohler K-8300-KS-NA Dimensions Guide

Kohler
Brand
Kohler
Model
K-8300-KS-NA
Category
Faucets
Type
Dimensions Guide

Kohler K-8300-KS-NA is a valve body rough-in designed for use in standard, back to back and thin wall installations. It includes a valve body, rough-in guide, and test cap. The 1/2" Universal NPT & direct sweat inlets & outlets, with stops, and service stops include integral check valves. The valve body features integral mounting locations and symmetrical valve inlets to simplify installation. The rough-in guide is designed for both standard and thin wall installations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers