Pro-Elec PEL01360 Operating instructions

Pro-Elec
Brand
Pro-Elec
Model
PEL01360
Category
Motion detectors
Type
Operating instructions

This manual is also suitable for

Pro-Elec PEL01360 is a solar-powered wall-mounted security light, designed for outdoor use. The light features a PIR (passive infrared) sensor, which detects motion and triggers the light to turn on. The light has two brightness settings: a low setting of 30% brightness for ambient lighting, and a high setting of 100% brightness when motion is detected. The light also has an adjustable detection range of 2-6 meters and a wide-angle lens of 120 degrees. The light is constructed to IP44 standards, making it suitable for outdoor use in all weather conditions.

Pro-Elec PEL01360 is a solar-powered wall-mounted security light, designed for outdoor use. The light features a PIR (passive infrared) sensor, which detects motion and triggers the light to turn on. The light has two brightness settings: a low setting of 30% brightness for ambient lighting, and a high setting of 100% brightness when motion is detected. The light also has an adjustable detection range of 2-6 meters and a wide-angle lens of 120 degrees. The light is constructed to IP44 standards, making it suitable for outdoor use in all weather conditions.

1
Solar Wall Security Lights
Model: PEL01359 and PEL01360
Please read these instructions carefully before use and retain for future reference.
IMPORTANT SAFETY INFORMATION
• Avoid locations of high temperature or humidity.
• The lamp is constructed to IP44 suitable for outdoor use.
WHAT’S INCLUDED
• Lamp assembly.
• User manual.
• Pack of screws and wall plugs.
POSITIONING
• The lamp is suitable for mounting on plasterboard, wood or masonry surfaces.
• It should be mounted in a position of maximum sunlight for optimum charge of the
internal battery.
• Before drilling any xing holes, check that there are no hidden obstructions behind
the mounting surface such as pipes or cables.
INSTALLATION
• Ideally mount the lamp 2-4 metres above ground for maximum sensing of
movement detection.
• Oer the lamp to the surface and mark the location of the upper xing hole.
• Measure vertically down from this location 118mm and mark the surface.
• Drill the wall if required, t the wall plugs and t the lower screw leaving the head
3-4mm proud of the surface.
• Locate the lower keyhole mounting point over the screw then attach the lamp
through the upper mounting point using the remaining screw provided.
2
OPERATION
• Allow at least 8hrs for the battery to fully charge initially.
CLEANING & MAINTENANCE
SPECIFICATION
• Clean the unit only with a soft damp cloth. Do not use any chemicals, abrasives or
solvents that could damage the casing or lens.
Solar panel: 5.5V, 0.8W.
Battery: 1 x 3.7V 1200mAh 18650 - non replaceable.
LED: 8 x white SMD and 2 x warm white SMD.
PIR: detection wide-angle lens of 120 degrees, range 2-6m.
Working time: up to 7 days.
Dimensions: L152 x W96 x H84mm.
• Press the on/o button once to activate the lamp.
• When the ambient light drops below 30 lux the lamp will illuminate at
approximately 30% of maximum brightness.
• If the PIR detector senses movement within range, the lamp will illuminate to
100% for 30 seconds after motion detection ceases before reducing to 30%
again.
NOTE: the lamp does not light except in low ambient light levels.
Lamp Unit
Solar panel
LED panel
PIR sensor
ON/OFF button
Wall plug
Screw
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical & Electronic
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area.
Made in China
PO Box 13362 Dublin 2
PR2 9PP
Man Rev 2.2
  • Page 1 1
  • Page 2 2

Pro-Elec PEL01360 Operating instructions

Pro-Elec
Brand
Pro-Elec
Model
PEL01360
Category
Motion detectors
Type
Operating instructions
This manual is also suitable for

Pro-Elec PEL01360 is a solar-powered wall-mounted security light, designed for outdoor use. The light features a PIR (passive infrared) sensor, which detects motion and triggers the light to turn on. The light has two brightness settings: a low setting of 30% brightness for ambient lighting, and a high setting of 100% brightness when motion is detected. The light also has an adjustable detection range of 2-6 meters and a wide-angle lens of 120 degrees. The light is constructed to IP44 standards, making it suitable for outdoor use in all weather conditions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents