ROOMS TO GO 90234279 Assembly Instructions

ROOMS TO GO
Brand
ROOMS TO GO
Model
90234279
Type
Assembly Instructions

ROOMS TO GO 90234279 is a floor lamp with a rotary on/off socket switch, suitable for dry locations only. It has a polarized plug for added safety and requires a single 60-watt bulb (not included). The lamp's shade consists of two parts (A and B) that attach to the socket and are secured with a socket ring. Assembly involves connecting the three tubes (bottom, middle, and upper) to form the base and attaching the shade components. The cable is then pulled under the base and up the side.

ROOMS TO GO 90234279 is a floor lamp with a rotary on/off socket switch, suitable for dry locations only. It has a polarized plug for added safety and requires a single 60-watt bulb (not included). The lamp's shade consists of two parts (A and B) that attach to the socket and are secured with a socket ring. Assembly involves connecting the three tubes (bottom, middle, and upper) to form the base and attaching the shade components. The cable is then pulled under the base and up the side.

21 Penn Plaza Suite 909 New York, NY 10001
Tel: (212) 736 4440 Fax: (212) 736 4806
www.adessohome.com
ASSEMBLY INSTRUCTIONS FOR
BRADBURY FLOOR LAMP
Model # 6049-20
1.06049-20
Base
Plug
Upper Tube
Middle Tube
Bottom Tube
Rotary on/o socket switch
Socket
Shade #A
Shade #B
Socket ring
Bulb (Not Included)
60 Watt
1. Screw bottom tube to base then screw middle
tube into bottom tube, and then upper tube into
middle tube.
2. Pull the cable under the base, then do the same on
side of base.
3. Attach shade A and shade B to socket then screw
on socket ring to fix shades.
4. Install the bulb (Not Included) by screwing it into
the socket. Refer to the label on the lamp socket
for maximum wattage information.
IMPORTANT SAFETY INSTRUCTIONS:
This portable lamp has a polarized plug (one
blade is wider than the other) as a feature to
reduce the risk of electric shock. This plug will
fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified
electrician. Never use with an extension cord
unless plug can be fully inserted.
DO NOT ALTER THE PLUG.
GENERAL PRODUCT INFORMATION:
This product is suitable
for dry locations only.
BULB TYPE: (1) 60Watt
Base
Enchufe
Poste superior
Poste del medio
Poste inferior
Interruptor giratorio de encendido/apagado
Boquilla
Pantalla A
Pantalla B
Anillo
Bombilla (no incluida)
60 vatios
LAMPARA DE PIE BRADBURY
21 Penn Plaza Suite 909 New York, NY 10001
Tel: (212) 736 4440 Fax: (212) 736 4806
www.adessohome.com
INSTRUCCIONES DE ENSAMBLAJE PARA
Modelo # 6049-20
1.06049-20
1. Enrosque el poste inferior en la base, después
enrosque el poste del medio en el poste inferior,
y luego el poste superior en el poste del medio..
2. Hale del cable debajo de la base, después haga lo
mismo en el lado de la base.
3. Coloque la pantalla A y la pantalla B en la
boquilla, después enrosque el anillo de la boquilla
para fijar las pantallas.
4. Coloque la bombilla (no incluida) enroscándolo
en la boquilla. Consulte la etiqueta en la boquilla
de la lámpara para obtener información máxima
de los vatios. .
INSTRUCCIONES IMPORTANTES DE SEGURIDAD:
Esta lámpara portátil tiene un enchufe polarizado
(una paleta es más ancha que la otra), función de
seguridad que reduce el riesgo de una descarga
eléctrica. Este enchufe encajará en un
tomacorriente polarizado en un sólo sentido.
Si el enchufe no entra completamente en el
tomacorriente, invierta el enchufe. Si aún así no
encaja, llame a un electricista calificado. Nunca
use un cable de extensión a menos que el enchufe
pueda insertarse por completo.
NO MODIFICAR EL ENCHUFE.
INFORMACION GENERAL DEL PRODUCTO:
Este producto es adecuado
sólo .para lugares secos
TIPO DE BOMBILLA (1) 60 Vatios
  • Page 1 1
  • Page 2 2

ROOMS TO GO 90234279 Assembly Instructions

ROOMS TO GO
Brand
ROOMS TO GO
Model
90234279
Type
Assembly Instructions

ROOMS TO GO 90234279 is a floor lamp with a rotary on/off socket switch, suitable for dry locations only. It has a polarized plug for added safety and requires a single 60-watt bulb (not included). The lamp's shade consists of two parts (A and B) that attach to the socket and are secured with a socket ring. Assembly involves connecting the three tubes (bottom, middle, and upper) to form the base and attaching the shade components. The cable is then pulled under the base and up the side.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents