Kenwood KVT-829DVD User manual

Category
Car video systems
Type
User manual

Kenwood KVT-829DVD is a versatile device that combines a monitor with a DVD receiver, providing a rich multimedia experience. It comes with an array of input and output options, allowing you to connect various devices such as iPods, USB drives, and external audio sources. The unit also features a rear-view camera input, enabling you to enhance your driving safety and convenience. Additionally, the KVT-829DVD includes pre-outs for front, rear, and subwoofer speakers, giving you the flexibility to expand your audio system and enjoy a more immersive sound experience.

Kenwood KVT-829DVD is a versatile device that combines a monitor with a DVD receiver, providing a rich multimedia experience. It comes with an array of input and output options, allowing you to connect various devices such as iPods, USB drives, and external audio sources. The unit also features a rear-view camera input, enabling you to enhance your driving safety and convenience. Additionally, the KVT-829DVD includes pre-outs for front, rear, and subwoofer speakers, giving you the flexibility to expand your audio system and enjoy a more immersive sound experience.

© B54-4555-00/00 (EV)
MONITOR WITH DVD RECEIVER
KVT-829DVD
INSTALLATION MANUAL
2
|
KVT-829DVD
Accessories
1
..........1
2
..........1
3
..........1
4
..........1
5
..........1
6
..........2
7
..........4
8
..........4
9
..........2
0
..........1
!
..........2
@
..........1
English
|
3
Installation Procedure
1. To prevent short circuits, remove the key from the
ignition and disconnect the - terminal of the
battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the wire on the wiring harness.
4. Take Connector B on the wiring harness and
connect it to the speaker connector in your vehicle.
5. Take Connector A on the wiring harness and
connect it to the external power connector on your
vehicle.
6. Connect the wiring harness connector to the unit.
7. Install the unit in your car.
8. Reconnect the - terminal of the battery.
9. Press the reset button.
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
Do not cut out the fuse from the ignition wire (red) and the
battery wire (yellow). The power supply must be connected
to the wires via the fuse.
¤
If the power is not turned ON (or it is ON, but will be OFF
immediately), the speaker wire may have a short-circuit
or touched the chassis of the vehicle and the protection
function may have been activated. Therefore, the speaker
wire should be checked.
If your car is not prepared for this special connection-
system, consult your Kenwood dealer.
Only use antenna conversion adapters (ISO-JASO) when the
antenna cord has an ISO plug.
Make sure that all wire connections are securely made by
inserting jacks until they lock completely.
If your vehicle’s ignition does not have an ACC position, or
if the ignition wire is connected to a power source with
constant voltage such as a battery wire, the power will not
be linked with the ignition (i.e., it will not turn on and off
along with the ignition). If you want to link the unit’s power
with the ignition, connect the ignition wire to a power
source that can be turned on and off with the ignition key.
If the fuse blows, first make sure that the wires have not
caused a short circuit, then replace the old fuse with one
with the same rating.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent short circuits, also do not remove
the caps on the ends of the unconnected wires or the
terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may receive damage or fail
to work if you share the - wires and/or ground them to
any metal part in the car.
After the unit is installed, check whether the brake lamps,
indicators, wipers, etc. on the car are working properly.
If the console has a lid, make sure to install the unit so
that the faceplate does not hit the lid when closing and
opening.
Mount the unit so that the mounting angle is 30° or less.
4
|
KVT-829DVD
Connection
iPod
PRK SW
BATT
ACC
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Monitor/Player unit
USB connector
USB device
(commercially available)
FUSE ( 10A )
FUSE ( 5A )
Ground wire (Black)
Connector A
Connector B
Ground wire (Black)
Do not connect.
The cable (Accessory 3) is
fixed with a chassis using
harness band (Accessory
!).
Accessory !
Wiring harness
(Accessory 2)
To connect the Kenwood navigation system,
consult your navigation manual.
USB connector (iPod)
USB device
(commercially available)
Accessory 0
(ISO–JASO)
Antenna Cord (ISO)
For the sake of safety, be sure to connect the parking sensor.
Connect to the vehicle's parking brake
detection switch harness
using the supplied relay connector.
Battery wire (Yellow)
Ignition wire (Red)
Steering remote control input (Light Blue/Yellow)
To steering remote
If no connections are made, do not let the cable come out from the tab.
Connect to the terminal that is grounded when either
the telephone rings or during conversation.
Mute wire (Brown)
Connect either to the power control terminal when using the optional
power amplifier, or to the antenna control terminal in the vehicle.
Power control/ Motor antenna control wire
(Blue/White)
To "EXT.AMP.CONT." terminal of the amplifier
having the external amp control function.
External amplifier control wire (Pink/Black)
(Orange/White)
Dimmer control wire (Orange/White)
To vehicle's reverse lamp harness
Reverse sensor wire (Purple/White)
Accessory 4
Parking sensor wire (Light Green)
English
|
5
REVERSE
ILLUMI
MUTE
ANT CONT
P. CONT
EXT. CONT
+
REMO.CONT
A
A
Receiver unit
Accessory 3
Receiver unit
Ground wire (Black) - (To car chassis)
Battery
If you connect the ignition wire (red) and the battery wire (yellow)
to the car chassis (ground), you may cause a short circuit, that in
turn may start a fire. Always connect those wires to the power
source running through the fuse box.
The cable (Accessory 3) is
fixed with a chassis using
harness band (Accessory
!).
Accessory !
Wiring harness
(Accessory 1)
FM/AM antenna input
6
|
KVT-829DVD
Connecting Wires to Terminals
Connector Function Guide
Pin Numbers for
ISO Connectors
Cable Colour Functions
External Power
Connector
A-4 Yellow Battery
A-5 Blue/White Power Control
A-6 Orange/White Dimmer
A-7 Red Ignition (ACC)
A-8 Black Earth (Ground)
Connection
Speaker
Connector
B-1 Purple Rear Right (+)
B-2 Purple/Black Rear Right (–)
B-3 Gray Front Right (+)
B-4 Gray/Black Front Right (–)
B-5 White Front Left (+)
B-6 White/Black Front Left (–)
B-7 Green Rear Left (+)
B-8 Green/Black Rear Left (–)
2WARNING
Connecting the ISO Connector
The pin arrangement for the ISO connectors depends on
the type of vehicle you drive. Make sure to make the proper
connections to prevent damage to the unit.
The default connection for the wiring harness is described in
1 below. If the ISO connector pins are set as described in 2
or 3, make the connection as illustrated.
Please be sure to reconnect the cable as shown 2 below to
install this unit to the Volkswagen vehicles etc.
1 (Default setting) The A-7 pin (red) of the vehicle’s
ISO connector is linked with the ignition, and the A-
4 pin (yellow) is connected to the constant power
supply.
Unit Vehicle
A-7 Pin (Red)
A-4 Pin (Yellow)
Ignition cable (Red)
Battery cable (Yellow)
2 The A-7 pin (red) of the vehicle’s ISO connector is
connected to the constant power supply, and the
A-4 pin (yellow) is linked to the ignition.
Unit Vehicle
A-7 Pin (Red)
A-4 Pin (Yellow)
Ignition cable
Battery cable
(Yellow)
3 The A-4 pin (yellow) of the vehicle’s ISO connector
is not connected to anything, while the A-7 pin
(red) is connected to the constant power supply
(or both the A-7 (red) and A-4 (yellow) pins are
connected to the constant power supply).
Unit Vehicle
A-7 Pin (Red)
A-4 Pin (Yellow)
Ignition cable (Red)
Battery cable (Yellow)
When the connection is made as in 3 above, the unit’s
power will not be linked to the ignition key. For that reason,
always make sure to turn off the unit’s power when the
ignition is turned off.
To link the units power to the ignition, connect the ignition
cable (ACC...red) to a power source that can be turned on
and off with the ignition key.
English
|
7
System Connection
RELAY 1
RELAY 2
Front Preout
• Audio left output (White)
• Audio right output (Red)
Rear Preout
• Audio left output (White)
• Audio right output (Red)
Subwoofer Preout
• Audio left output (White)
• Audio right output (Red)
Rear View Camera Input
Visual input (Yellow)
Audio/Visual Output
Visual output (Yellow)
• Audio left output (White)
• Audio right output (Red)
Audio/Visual input 2
Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
Receiver unit
Audio/Visual input 1
Visual input (Yellow)
• Audio left input (White)
• Audio right input (Red)
To Relay Box
Accessory @
8
|
KVT-829DVD
Optional Accessory Connection
TV ANTENNA INPUT
TO MONITOR UNIT
iPod
AUDIO IN
iPod
VIDEO IN
iPod
Receiver unit
KCA-iP300V
(Optional Accessory)
iPod
(commercially available)
Disc Changer etc.
(Optional Accessory)
TV Tuner
(Optional Accessory)
Connection cable
(Included in the TV tuner)
Connection cable
(Included in the Disc changer)
Audio Output
(Black)
Visual Input
Resistance-free mini plug (3.5Ф)
Visual Output
(Yellow)
Audio Input
Resistance-free stereo type mini
plug (3.5Ф)
USB terminal (iPod)
USB terminal
Navigation System
(Optional Accessory)
Connection cable
(Included in the Navigation System)
Accessory 3
Monitor/Player unit
USB terminal
iPod cannot be connected.
English
|
9
Installation for Monitor/Player Unit
1. Attach the installation brackets 9 to the sides of
the receiver unit using the sems bolts 7.
2. Use the tapping screw 8 to secure the receiver
unit to the audio board.
Installation brackets
(Accessory 9)
Sems bolts (M4 × 8 mm)
(Accessory 7)
Tapping screw (ø4 × 16 mm)
(Accessory 8)
Installation for Receiver Unit
Accessory 5
Bend the tabs of the mounting
sleeve with a screwdriver or similar
utensil and attach it in place.
Metal mounting strap
(commercially available)
Self-tapping screw
(commercially available)
Screw (M4X8)
(commercially available)
Firewall or metal support
Make sure that the unit is installed securely in place. If the unit is unstable,
it may malfunction (eg, the sound may skip).
10
|
KVT-829DVD
Removing Monitor/Player Unit
Removing the Hard Rubber Frame
(escutcheon)
1. Engage the catch pins on the removal tool 6 and
remove the two locks on the lower level.
Lower the frame and pull it forward as shown in
the figure.
Removal Tool (Accessory 6)
Lock
Catch
The frame can be removed from the top side in the same
manner.
2. When the lower level is removed, remove the
upper two locations.
Removing the Unit
1. Remove the hard rubber frame by referring to the
removal procedure in the section <Removing the
Hard Rubber Frame>.
2. Remove the Hex-head screw with integral washer
(M4 × 8) on the back panel.
3. Insert the two removal tools 6 deeply into the
slots on each side, as shown.
Removal Tool
(Accessory 6)
4. Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
Be careful to avoid injury from the catch pins on the
removal tool.
5. Pull the unit all the way out with your hands, being
careful not to drop it.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Kenwood KVT-829DVD User manual

Category
Car video systems
Type
User manual

Kenwood KVT-829DVD is a versatile device that combines a monitor with a DVD receiver, providing a rich multimedia experience. It comes with an array of input and output options, allowing you to connect various devices such as iPods, USB drives, and external audio sources. The unit also features a rear-view camera input, enabling you to enhance your driving safety and convenience. Additionally, the KVT-829DVD includes pre-outs for front, rear, and subwoofer speakers, giving you the flexibility to expand your audio system and enjoy a more immersive sound experience.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI