Kenwood KVT-829DVD User manual

Brand: Kenwood

Model: KVT-829DVD

Category: Car video systems

Type: User manual

Kenwood KVT-829DVD is a versatile device that combines a monitor with a DVD receiver, providing a rich multimedia experience. It comes with an array of input and output options, allowing you to connect various devices such as iPods, USB drives, and external audio sources. The unit also features a rear-view camera input, enabling you to enhance your driving safety and convenience. Additionally, the KVT-829DVD includes pre-outs for front, rear, and subwoofer speakers, giving you the flexibility to expand your audio system and enjoy a more immersive sound experience.

MONITOR WITH DVD RECEIVER

KVT-829DVD

INSTALLATION MANUAL

KVT-829DVD

Accessories

..........1

..........2

..........4

..........2

..........1

..........2

..........1

English

Installation Procedure

1. To prevent short circuits, remove the key from the

ignition and disconnect the - terminal of the

battery.

2. Make the proper input and output wire

connections for each unit.

3. Connect the wire on the wiring harness.

4. Take Connector B on the wiring harness and

connect it to the speaker connector in your vehicle.

5. Take Connector A on the wiring harness and

connect it to the external power connector on your

vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

8. Reconnect the - terminal of the battery.

9. Press the reset button.

2WARNING

• If you connect the ignition wire (red) and the battery wire

(yellow) to the car chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always connect those

wires to the power source running through the fuse box.

• Do not cut out the fuse from the ignition wire (red) and the

battery wire (yellow). The power supply must be connected

to the wires via the fuse.

• If the power is not turned ON (or it is ON, but will be OFF

immediately), the speaker wire may have a short-circuit

or touched the chassis of the vehicle and the protection

function may have been activated. Therefore, the speaker

wire should be checked.

• If your car is not prepared for this special connection-

system, consult your Kenwood dealer.

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

• Make sure that all wire connections are securely made by

inserting jacks until they lock completely.

• If your vehicle’s ignition does not have an ACC position, or

if the ignition wire is connected to a power source with

constant voltage such as a battery wire, the power will not

be linked with the ignition (i.e., it will not turn on and off

along with the ignition). If you want to link the unit’s power

with the ignition, connect the ignition wire to a power

source that can be turned on and off with the ignition key.

• If the fuse blows, first make sure that the wires have not

caused a short circuit, then replace the old fuse with one

with the same rating.

• Insulate unconnected wires with vinyl tape or other similar

material. To prevent short circuits, also do not remove

the caps on the ends of the unconnected wires or the

terminals.

• Connect the speaker wires correctly to the terminals to

which they correspond. The unit may receive damage or fail

to work if you share the - wires and/or ground them to

any metal part in the car.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• If the console has a lid, make sure to install the unit so

that the faceplate does not hit the lid when closing and

opening.

• Mount the unit so that the mounting angle is 30° or less.

KVT-829DVD

Connection

iPod

PRK SW

BATT

ACC

Monitor/Player unit

USB connector

USB device

(commercially available)

FUSE ( 10A )

FUSE ( 5A )

Ground wire (Black)

Connector A

Connector B

Ground wire (Black)

Do not connect.

The cable (Accessory 3) is

fixed with a chassis using

harness band (Accessory

!).

Accessory !

Wiring harness

(Accessory 2)

To connect the Kenwood navigation system,

consult your navigation manual.

USB connector (iPod)

USB device

(commercially available)

Accessory 0

(ISO–JASO)

Antenna Cord (ISO)

For the sake of safety, be sure to connect the parking sensor.

Connect to the vehicle's parking brake

detection switch harness

using the supplied relay connector.

Battery wire (Yellow)

Ignition wire (Red)

Steering remote control input (Light Blue/Yellow)

To steering remote

If no connections are made, do not let the cable come out from the tab.

Connect to the terminal that is grounded when either

the telephone rings or during conversation.

Mute wire (Brown)

Connect either to the power control terminal when using the optional

power amplifier, or to the antenna control terminal in the vehicle.

Power control/ Motor antenna control wire

(Blue/White)

To "EXT.AMP.CONT." terminal of the amplifier

having the external amp control function.

External amplifier control wire (Pink/Black)

(Orange/White)

Dimmer control wire (Orange/White)

To vehicle's reverse lamp harness

Reverse sensor wire (Purple/White)

Accessory 4

Parking sensor wire (Light Green)

English

REVERSE

ILLUMI

MUTE

ANT CONT

P. CONT

EXT. CONT

REMO.CONT

Receiver unit

Accessory 3

Receiver unit

Ground wire (Black) - (To car chassis)

Battery

If you connect the ignition wire (red) and the battery wire (yellow)

to the car chassis (ground), you may cause a short circuit, that in

turn may start a fire. Always connect those wires to the power

source running through the fuse box.

The cable (Accessory 3) is

fixed with a chassis using

harness band (Accessory

!).

Accessory !

Wiring harness

(Accessory 1)

FM/AM antenna input

KVT-829DVD

Connecting Wires to Terminals

Connector Function Guide

Pin Numbers for

ISO Connectors

Cable Colour Functions

External Power

Connector

A-4 Yellow Battery

A-5 Blue/White Power Control

A-6 Orange/White Dimmer

A-7 Red Ignition (ACC)

A-8 Black Earth (Ground)

Connection

Speaker

Connector

B-1 Purple Rear Right (+)

B-2 Purple/Black Rear Right (–)

B-3 Gray Front Right (+)

B-4 Gray/Black Front Right (–)

B-5 White Front Left (+)

B-6 White/Black Front Left (–)

B-7 Green Rear Left (+)

B-8 Green/Black Rear Left (–)

2WARNING

Connecting the ISO Connector

The pin arrangement for the ISO connectors depends on

the type of vehicle you drive. Make sure to make the proper

connections to prevent damage to the unit.

The default connection for the wiring harness is described in

1 below. If the ISO connector pins are set as described in 2

or 3, make the connection as illustrated.

Please be sure to reconnect the cable as shown 2 below to

install this unit to the Volkswagen vehicles etc.

1 (Default setting) The A-7 pin (red) of the vehicle’s

ISO connector is linked with the ignition, and the A-

4 pin (yellow) is connected to the constant power

supply.

Unit Vehicle

A-7 Pin (Red)

A-4 Pin (Yellow)

Ignition cable (Red)

Battery cable (Yellow)

2 The A-7 pin (red) of the vehicle’s ISO connector is

connected to the constant power supply, and the

A-4 pin (yellow) is linked to the ignition.

Unit Vehicle

A-7 Pin (Red)

A-4 Pin (Yellow)

Ignition cable

Battery cable

(Yellow)

3 The A-4 pin (yellow) of the vehicle’s ISO connector

is not connected to anything, while the A-7 pin

(red) is connected to the constant power supply

(or both the A-7 (red) and A-4 (yellow) pins are

connected to the constant power supply).

Unit Vehicle

A-7 Pin (Red)

A-4 Pin (Yellow)

Ignition cable (Red)

Battery cable (Yellow)

⁄

• When the connection is made as in 3 above, the unit’s

power will not be linked to the ignition key. For that reason,

always make sure to turn off the unit’s power when the

ignition is turned off.

To link the unit’s power to the ignition, connect the ignition

cable (ACC...red) to a power source that can be turned on

and off with the ignition key.

English

System Connection

RELAY 1

RELAY 2

■ Front Preout

• Audio left output (White)

• Audio right output (Red)

■ Rear Preout

• Audio left output (White)

• Audio right output (Red)

■ Subwoofer Preout

• Audio left output (White)

• Audio right output (Red)

■ Rear View Camera Input

• Visual input (Yellow)

■ Audio/Visual Output

• Visual output (Yellow)

• Audio left output (White)

• Audio right output (Red)

■ Audio/Visual input 2

• Visual input (Yellow)

• Audio left input (White)

• Audio right input (Red)

Receiver unit

■ Audio/Visual input 1

• Visual input (Yellow)

• Audio left input (White)

• Audio right input (Red)

To Relay Box

Accessory @

KVT-829DVD

Optional Accessory Connection

TV ANTENNA INPUT

TO MONITOR UNIT

iPod

AUDIO IN

iPod

VIDEO IN

iPod

Receiver unit

KCA-iP300V

(Optional Accessory)

iPod

(commercially available)

Disc Changer etc.

(Optional Accessory)

TV Tuner

(Optional Accessory)

Connection cable

(Included in the TV tuner)

Connection cable

(Included in the Disc changer)

Audio Output

(Black)

Visual Input

Resistance-free mini plug (3.5Ф)

Visual Output

(Yellow)

Audio Input

Resistance-free stereo type mini

plug (3.5Ф)

USB terminal (iPod)

USB terminal

Navigation System

(Optional Accessory)

Connection cable

(Included in the Navigation System)

Accessory 3

Monitor/Player unit

USB terminal

iPod cannot be connected.

English

Installation for Monitor/Player Unit

1. Attach the installation brackets 9 to the sides of

the receiver unit using the sems bolts 7.

2. Use the tapping screw 8 to secure the receiver

unit to the audio board.

Installation brackets

(Accessory 9)

Sems bolts (M4 × 8 mm)

(Accessory 7)

Tapping screw (ø4 × 16 mm)

(Accessory 8)

Installation for Receiver Unit

Accessory 5

Bend the tabs of the mounting

sleeve with a screwdriver or similar

utensil and attach it in place.

Metal mounting strap

(commercially available)

Self-tapping screw

(commercially available)

Screw (M4X8)

(commercially available)

Firewall or metal support

Make sure that the unit is installed securely in place. If the unit is unstable,

it may malfunction (eg, the sound may skip).

KVT-829DVD

Removing Monitor/Player Unit

Removing the Hard Rubber Frame

(escutcheon)

1. Engage the catch pins on the removal tool 6 and

remove the two locks on the lower level.

Lower the frame and pull it forward as shown in

the figure.

Removal Tool (Accessory 6)

Lock

Catch

⁄

• The frame can be removed from the top side in the same

manner.

2. When the lower level is removed, remove the

upper two locations.

Removing the Unit

1. Remove the hard rubber frame by referring to the

removal procedure in the section <Removing the

Hard Rubber Frame>.

2. Remove the Hex-head screw with integral washer

(M4 × 8) on the back panel.

3. Insert the two removal tools 6 deeply into the

slots on each side, as shown.

Removal Tool

(Accessory 6)

4. Lower the removal tool toward the bottom, and

pull out the unit halfway while pressing towards

the inside.

⁄

• Be careful to avoid injury from the catch pins on the

removal tool.

5. Pull the unit all the way out with your hands, being

careful not to drop it.

Kenwood KVT-829DVD User manual

Brand: Kenwood

Model: KVT-829DVD

Category: Car video systems

Type: User manual

Download PDF

report

Kenwood KVT-829DVD User manual

Kenwood KVT-829DVD User manual

Related papers

Other documents