Toro Bagger Dump Kit, Out-Front Z Installation guide

Brand: Toro

Model: Bagger Dump Kit, Out-Front Z

Type: Installation guide



The T

oro Company – 1999

Printed in USA

FORM NO. 3323-106

INSTALLATION

INSTRUCTIONS

Part No. 100–2441

Bagger Dump Kit

for Out Front Z

Loose

Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Dump Plate

Install Dump Plate

Hopper Floor Plate

Screw

Flat W

asher

Locknut

Install Hopper Floor

Emitter Bracket

Install Emitter Bracket

Installation Instructions

Installing

Dump Plate

1. Disengage the power take off (PTO), set the

parking brake, and turn the ignition key to

“OFF” to stop the engine. Remove the key.

2. Remove the existing three bolts that hold hopper

to the frame (Fig. 1). Save existing hardware.

3. Slide the dump plate under the hopper. Align

holes with the existing holes in hopper and

frame (Fig. 1).

4. Install nuts and bolts (Fig. 1).



Figure 1

1. Hopper

2. Nut

3. Bolt

4. Dump

Plate

Installing

Hopper Floor Plate

1. Lift rear hopper door. Clean out any loose grass

and debris.

2. Tilt hopper floor plate at an angle to place it into

the hopper.

Note: The bent tabs must face down. Short

tab must be towards back of hopper

(Fig. 2).

3. Using the two front holes in floor as a template,

drill two 9/32 holes into the floor of the hopper

(Fig. 2).

4. Install a screw, flat washer and nut to fasten the

floor plate to hopper floor (Fig. 2).

Note: No hardware is needed in the two back

holes in hopper floor (Fig. 2).



Figure 2

1. Hopper

2. Hopper

Floor Plate

3. Screw

Flat W

asher

Lock Nut

Bent T

ab (Short tab and

facing down)

Rear holes in hopper floor

(No hardware required for

them)

Installation Instructions

Installing

New Emitter Bracket

The new emitter bracket can be installed to allow an

earlier signal when hopper is full. The receiver

bracket must be moved also when an earlier signal is

desired.

Installing Emitter

1. Lift rear hopper door. Clean out any loose grass

and debris around emitter and receiver.

2. Remove the emitter from existing bracket

(Fig. 3). Save existing hardware.

3. Remove the existing emitter bracket and rear

wire clip (Fig. 3). Save existing hardware.

Note: The rear wire clip will need to be

reinstalled on the front hole in new

emitter bracket (Fig. 3).

4. Install emitter to new bracket. Install into lower

holes to receive an earlier signal when the

hopper is full.(Fig. 3). Use existing hardware.

5. Install new emitter bracket with wire clip in front

hole (Fig. 3). Use existing hardware.

Moving Receiver

1. Remove the receiver bracket from the front of

hopper. Keep the receiver attached to bracket

(Fig. 3). Save existing hardware.

2. Install a bolt through the bottom hole in the

hopper and into the top hole of bracket (Fig. 3).

The top hole in hopper is not used.

3. Using the bottom hole in the bracket as a

template, drill a 9/32” hole into the hopper.

Make sure the holes are in line vertically before

drilling (Fig. 3).

4. Install a bolt into the bottom hole of bracket and

drilled hole in hopper (Fig. 3).

Note: Make sure the wire between receiver,

wire clips and emitter is tight. It will

collect grass clippings if it is not.

(Fig. 3).



Figure 3

1. Emitter

2. New

Emitter Bracket

Receiver and Bracket

Hole to drill

Rear Wire Clip

Front of Hopper

Emitter Wire

Installation Instructions

Toro Bagger Dump Kit, Out-Front Z Installation guide

Toro Bagger Dump Kit, Out-Front Z Installation guide

Toro Bagger Dump Kit, Out-Front Z Installation guide

Related papers

Other documents