Toro Rear Cover Kit, TX Series Compact Utility Loader Installation guide

Brand: Toro

Model: Rear Cover Kit, TX Series Compact Utility Loader

Type: Installation guide

Toro Rear Cover Kit, TX Series Compact Utility Loader is designed to provide a secure and protective covering for the rear of your TX Series Compact Utility Loader. It offers easy access to the engine and other components for maintenance and repairs, while also safeguarding them from dirt, debris, and other elements. Installation is straightforward and can be completed using common tools and the detailed instructions included in the kit. The kit includes all necessary hardware, including cover supports, a rear cover, rivets, washers, knobs, and retaining rings.

Form No. 3353-884 Rev A

Rear Cover Kit

For TX Series Compact Utility Loader

Model No. 108-4657

Installation Instructions

Installation

Loose Parts

Use the chart below to verify that all parts have been shipped.

Step

Description

Qty.

Use

No parts required

–

Prepare the Machine

Cover support, left side

Cover support, right side

Bolt, (1/4 x 3/4 inch)

Install the side cover supports.

Cover, rear

Rivet

Washer, back

Knob

Washer

Ring, retaining

Install the rear cover.

Note: Deter mine the left and right sides of the mac hine from the nor mal operating position.

Note: T his installation of this kit will require drilling holes into the mac hine c hassis . A v oid damaging

the mac hine b y understanding what is behind the surface to be drilled and tak e precaution not to har m

any inter nal par ts .

Step

Preparing the Machine

No Parts Required

Procedure

Lo w er the loader ar ms , stop the engine and

remo v e the k ey .

1. Open the rear co v er b y unlatc hing the fastener

on the left side of the mac hine ( Figure 1 ).

2. R emo v e the fasteners securing the latc h to the

mac hine . Discard latc h and fasteners ( Figure

1 ).

8111 Lyndale Avenue South

Bloomington, MN 55420

Printed in the USA.

Figure 1

1. Latch

3. Fastener

2. Rear cover

4. Latch plate

3. One the right side of the mac hine , remo v e the

fasteners securing the hing e plate to rear co v er

( Figure 2 ). Discard the fasteners .

Figure 2

1. Rear cover

5. Bolt

2. Washer 6. Lock nut

3. Hinge

7. Hinge plate

4. Machine frame

4. R emo v e the fasteners securing the R-clamp

and Operator’ s Manual tube to the co v er . Discard

the fasteners and co v er . R etain the Operator’ s

Manual housing tube and clamps .

5. R emo v e the fasteners securing the hing e co v er

and hing e to the mac hine ( Figure 2 ). R emo v e

the hing e co v er , hing e , and fasteners and

discard.

Step

Installing the Side Cover

Supports

Parts needed for this step:

Cover support, left side

Cover support, right side

Bolt, (1/4 x 3/4 inch)

Procedure

1. Locate the left and right side co v er suppor ts

in the loose par ts .

2. On the left side of the mac hine , measure and

mark at the location as sho wn in Figure 3 .

Measure 2-7/8 inc h bac k from the frame edg e

along the base of the control panel frame and

1/2 inc h up .

Figure 3

Left cover support

1. Drill surfaces 3. Mark and drill 0.234 inch

diameter hole here

2. Frame edge 4. Mark line

3. Drill a 15/64 inc h diameter hole a the mark ed

location.

Important: T ak e caution not to dama ge

an y inter nal machine components dir ectl y

behind the mar k ed location when drilling

the holes.

4. Scribe a line through the drilled hole , parallel

to the bottom edg e and along the side of the

control panel frame .

5. Using the left side co v er suppor t as a template

( Figure 4 ), align the upper , forw ard hole with

the hole drilled in ste p 3 .

6. Inser t a screw to in the upper , forw ard hole of

the co v er and rotate the co v er until the rear ,

upper hole sho ws the line scribed previously

( Figure 4 ). Mark the location of the upper , rear

hole and mark the location of the lo w er hole

in the co v er .

Figure 4

Left cover support

1. Left side cover 4. Mark rear hole here

2. Drilled hole 5. Bolt, 1/4 x 3/4 inch

3. Mark lower hole here

7. R emo v e the co v er and fastener . Drill tw o

15/64 inc h diameter holes in the locations

mark ed.

Important: T ak e caution not to dama ge

an y inter nal machine components dir ectl y

behind the mar k ed location when drilling

the holes.

8. Install the co v er using 3 bolts (1/4 x 3/4 inc h)

located in loose par ts ( Figure 4 ).

9. T o install the right rear co v er , re peat this

procedure on the opposite side of the mac hine

with the remaining co v er .

Step

Installing the Rear Cover

Parts needed for this step:

Cover, rear

Rivet

Washer, back

Knob

Washer

Ring, retaining

Procedure

1. Install the R-clamps with the Operator’ s Manual

tube to the rear co v er using 2 ri v ets and 2 bac k

w ashers located in loose par ts .

2. Install a knob and w asher in eac h cor ner of the

rear co v er as sho wn in Figure 5 . Secure eac h

knob and w asher with a retaining ring .

Figure 5

1. Rear cover

4. Retaining ring

2. Knob 5. Slot

3. Washer

3. Install the rear co v er to the mac hine b y

inser ting the tabs on the lo w er end of the co v er

into the slots in the co v er suppor ts installed

earlier . Push the co v er forw ard and line up

the knob with the upper holes in the co v er

suppor ts . Tighten the knobs to secure the

co v er in place .

Toro Rear Cover Kit, TX Series Compact Utility Loader Installation guide

Toro Rear Cover Kit, TX Series Compact Utility Loader Installation guide

Toro Rear Cover Kit, TX Series Compact Utility Loader Installation guide

Related papers

Other documents