R03.002_11/01/2012
TECHNICAL FILE
NovoIistel® SliMM
Novolistel® SliMM is part of the Emac®’s SliMM range, specially
designed to its installation with low thickness ceramics, small tiles
and thin mosaics. This prole is made of aluminium and is very
versatile because in addition to its main function as decorative
listello, it can be installed as ooring separator, edge protector, stair
nosing or decorative nish. This listello is available in anodized and
lacquered nishes of latest trends, offering multiple decorative
possibilities.
General Features
Material:
Anodized/lacquered
aluminium
Length: 8ft2in / 2,5 l.m.
Dimensions: a: 7/32” / 5,7 mm.
h: 3/16” / 4,5 mm.
Packaging: 50 u/box
Finishes:
Applications
Novolistel® SliMM is a prole with multiple applications, for example:
- Decorative listello
- Edge protector
- Flooring separator
- Stair nosing or nish (worktops, half height...)
Novolistel® SliMM has a complementary piece made of zamak to place the proles in right angle with
the best nish.
Angle piece Novolistel® SliMM
Complementary pieces
Technical Features
Page 1 of 4
Alloy: 6063 (AA and ASTM)
L-3441 (UNE 38-301-89)
Fire resistance: M0 (UNE 23-727-90)
Abrasion resistance: Very good
Lightfastness: Excellent
Appearance and color: EN 12373-1
Reg. 1668435-10
R03.002_11/01/2012
TECHNICAL FILE
Novolistel® SliMM
Materials
Aluminum
Novolistel® SliMM is a prole made by extrusion of aluminum. The bright gold, matt gold, bright silver,
matt silver and matt black nishes have been anodized, improving through this process their corrosion
resistance, mechanical resistance and appearance. The anodized applied has the quality seal Quala-
nod, which guarantees the quality of the process and the resulting proles. This seal regulates several
tests: appearance and color, thickness measurements, sealing and impregnation control, abrasion re-
sistance, lightfastness, acetic saline chamber and nitric acid immersion.
The white and matt beige nishes have been lacquered, obtaining so a high quality and homogeneus
surface. The lacquering has the quality seal Qualicoat, which guarantees the quality of the process and
the nal products.
Aluminum has excellent chemical, physical and mechanical properties. It is lightweight, tough, ductile,
malleable and highly durable.
1, Spread a big amount of thin-set mortar on the surface to be tiled.
2. Align the prole with the corner and press it so the thin-set mortar passes through the holes of the
anchoring wing.
3. Place tiles on the xing wing and press them to get an optimal adhesion.
4. Continue tiling the wall.
5. Finally, clean the leftover material, remove the protective lm if necessary and let dry.
*See pictures in the next page.
Placement
Zamak
As listello
As edge protector
The complementary piece of Novocanto® SliMM is made of Zamak. Zamak is a non ferrous alloy of Zinc
with aluminium, magnesium and copper (UNE EN 1774). It is tough, has high hardness, high mechanical
strength and excellent plastic deformability.
The surface nish applied, protects the prole and is similar to Novocanto® SliMM’s nishes.
*You can nd out more information by consulting the Technical les of materials in www.emac.es
Page 2 of 4
1. First spread a big amount of thin-set mortar on the surface to be tiled and then tile it up to the ap-
proximated height where you’ll place the listello.
2. Place the tiles in the end of the next row, aligning them with the previous tiles. Then place the prole
aligned to them, embedding the anchoring wing between the wall and the tiles. Press the prole to
ensure the thin-set mortar passes through the holes of the anchoring wing.
3. Place the remaining tiles, pressing softly to get an optimal adhesion.
4. Then, continue tiling the wall up to the desired height.
5. Finally, clean the leftover material and let dry.
1
2 3
4
R03.002_11/01/2012
TECHNICAL FILE
Novolistel® SliMM
1
1
2
2
3
3
4
4
5
5
The cleaning must be done periodically with a soft cloth. If you use a neutral liquid cleaner, you must
rinse the prole with cold water and dry to remove excess moisture. If dirtiness persists, clean the
prole with a solution with clean water and detergent or neutral soap 5%, brushing with a cloth that
has no particles that could scracht the nish. Ensure the lacquered surface is totally cold (maximum
20ºC) before the cleaning.
Steel wool, abrasive cleaners, souring products as well as strong acids (hydrochloric and
perchloric),strong bases (caustic soda or ammonia) or carbonated solutions are not recommended.
Citric acid is neither recommended because disolves the protective layer of the surface of aluminium.
Waxes, petrolatum, lanolin or similar substances are not appropriate. Solvents containing haloalkanes
(hydrouoroether and chlorinated solvents) and curing accelerators containing chlorides should not be
used (use special accelerators free of chlorides).
Cleaning and maintenance
As ooring separator
To see the video, capture this
image with your mobile phone
(QR code reader software is
necessary) or click on it.
Page 3 of 4
1. Spread a big amount of thin-set mortar on the surface to be tiled.
2. Then, place the prole and press it so the thin-set mortar passes through the holes of the anchoring
wing.
3. Place a tile on the anchoring wing and press it to get an optimal contact with the thin-set mortar.
4. Repeat the the previous step by placing tiles both sides the prole until the installation is complete.
5. Finally, clean the leftover material, remove the protective lm if necessary and let dry.
* If you plan on polishing the oor, install the prole slightly below the tile.
1. Spread a big amount of thin-set mortar on the riser
2. Tile the riser.
3. Then, spread a big amount of thin-set mortar on the tread and align the prole on its vertex (Do not
let overhang, the leverage may remove the step and the tiles). Then press it so the thin-set mortar
passes through the holes of the anchoring wing
4. Place a tile on the tread, align it to the prole and press it to ensure a perfect adhesion. Continue
tiling.
5. Clean the possible leftover material and let dry
As stair nosing or
worktop nish
1 2 3
4 5
TECHNICAL FILE
R03.002_11/01/2012
Emac Complementos S.L. (Spain) info@emac.es // Emac America L.L.C. (FL,USA) [email protected] // Emac Italia S.R.L. (Italy) [email protected]
www.emac.es
The data provided are for information only and have been obtained by our supplier or Emac®.
Does not constitute legal guarantee in terms of properties and / or functionality of the application of material
You can nd out more information about the technical features of Emac®’s products by downloading
its Technical File in www.emac.es.
If you have any query, please contact our Technical Department in tecnico@emac.es.
Technical information
Novolistel® SliMM
Indoors Wall tiling Recyclable
Page 4 of 4
/
