Grip-Rite SLG4250GRE is a lightweight synthetic underlayment designed to replace #15 saturated asphalt felt. It is a water shedding device designed to reduce the occurrence of leaks caused by wind-driven rain penetrating the primary roof system coverings as well as a temporary cover on exposed roof decks.
Grip-Rite SLG4250GRE is 10 SQ coverage and has superior tear resistance. It is UV treated for 180 day exposure and is 5 times lighter than #15 felt. It contains no asphalt and is mold and crack resistant. It has a printed nail and overlap pattern and is AC 188 approved. It meets ASTM D226 (non-asphalt properties), ASTM D4869 (non-asphalt properties), ASTM E96 (non-asphalt properties), and CAN CSA 123.3-05 (non-asphalt properties) standards.
Grip-Rite SLG4250GRE is a lightweight synthetic underlayment designed to replace #15 saturated asphalt felt. It is a water shedding device designed to reduce the occurrence of leaks caused by wind-driven rain penetrating the primary roof system coverings as well as a temporary cover on exposed roof decks.
Grip-Rite SLG4250GRE is 10 SQ coverage and has superior tear resistance. It is UV treated for 180 day exposure and is 5 times lighter than #15 felt. It contains no asphalt and is mold and crack resistant. It has a printed nail and overlap pattern and is AC 188 approved. It meets ASTM D226 (non-asphalt properties), ASTM D4869 (non-asphalt properties), ASTM E96 (non-asphalt properties), and CAN CSA 123.3-05 (non-asphalt properties) standards.
ShingleLayment
®
Lightweight Synthetic Underlayments
ShingleLayment
®
Lightweight synthetic underlayments
GRSLLBRO
03/2014
Introducing two new
lightweight synthetic roong
underlayments, designed
to replace #15 saturated
asphalt felt.
Product Name:
Grip-Rite ShingleLayment-E
®
Grip-Rite ShingleLayment-15
®
Manufacturer:
PrimeSource Building Products, Inc.
1321 Greenway Drive, Irving, TX 75038
800-676-7777
www.primesourcebp.com
www.grip-rite.com
Product Description:
ShingleLayment-E is a lightweight version of our
proven Grip-Rite ShingleLayment. Woven 8 x 7 scrim
Polypropylene substrate coated on the walking surface
with a non-skid TPO. ShingleLayment-E has high tensile
strength to resist blow off from high wind exposure.
ShingleLayment-E can be used under any mechanically
attached asphalt shingle application.
ShingleLayment-15 is a woven 10 x 10 scrim
polypropylene substrate coated on the walking surface
with a spun bonded non-woven that provides non-skid
traction. ShingleLayment-15 has high tensile
strength to resist blow-off from high wind exposure.
ShingleLayment-15 can be used under any mechanically
attached asphalt shingle application.
Application:
Both products are designed for use on steep slope
roofs beneath asphalt shingles as an alternate to
ASTM D226, Type I or II or ASTM D4869 asphalt felts.
Both are a water shedding device designed to reduce
the occurrence of leaks caused by wind-driven rain
penetrating the primary roof system coverings
as well as a temporary cover on exposed roof decks.
These new synthetics outperform felt in every way – they roll out at, hold a chalk line, have a non-skid surface,
are mold resistant, and resist tear and cracking.
ShingleLayment Lightweights™ are backed by a limited warranty – felt paper doesn’t come close.
Finish the job right with Grip-Rite Eave & Valley Protector
™
and Grip-Rite Fasteners
®
.
Grip-Rite ShingleLayment
®
is distributed by PrimeSource Building Products, Inc.
© 2014 PrimeSource Building Products, Inc.
800-676-7777
www.grip-rite.com
www.primesourcebp.com
SKU Description
Size
Color
Weight/
Roll
Rolls/
Pallet
Pallets/
Truckload
Rolls/
TruckloadArea Dimensions
SLG4250GRE ShingleLayment-E 10 SQ 4 ft. x 250 ft. Gray 19.5 lb. 64 30 1,920
SL154250GR ShingleLayment-15 10 SQ 4 ft. x 250 ft. Gray 22.5 lb. 49 35 1,715
ShingleLayment-E
- Gray
ShingleLayment-15
- Gray
The time to convert from asphalt felt is NOW, with the new Grip-Rite
ShingleLayment Lightweight series of synthetic underlayments.
Features & Approvals:
Both Products
10 SQ coverage
Superior tear resistance
UV treated for 180 day exposure
5 times lighter than #15 felt
Contains no asphalt
Mold & crack resistant
Printed nail and overlap pattern
AC 188
ASTM D226 (non-asphalt properties)
ASTM D4869 (non-asphalt properties)
ASTM E96 (non-asphalt properties)
CAN CSA 123.3-05 (non-asphalt properties)
ShingleLayment-E
Non skid TPO walking surface
10 year warranty
Exclusive shingle print pattern
ShingleLayment-15
Non-skid SBPP surface
10 year limited warranty
Installer print pattern
ShingleLayment
®
Lightweight Synthetic Underlayments
ShingleLayment
®
Lightweight Synthetic Underlayments
Precautions & Limitations:
Depending on roof pitch and surface conditions (wet, dusty, frost), the coefcient of friction may change, and can become
slippery. Use caution.
Use caution when walking on roof deck and use OSHA compliant fall protection.
Do not walk or stand on ShingleLayment-E or ShingleLayment-15 until it is attached to roof deck according to installation
instructions.
Shingle print pattern is not intended for use as an installation grid for nal roong surface shingles.
ShingleLayment-E and ShingleLayment-15 are not designed as a primary roof covering. Exposure beyond 30-days without nal
roof covering may subject the sheet to jobsite abuse, chemical exposure, and severe weather.
ShingleLayment-E and ShingleLayment-15 may not be used in any exposed application such as crickets, exposed valleys,
or exposed roof to wall details.
Attic spaces must be property ventilated in accordance with the local Building Code.
Minimum roof pitch: 2:12 (9.4°).
Physical Properties
Properties Standard ShingleLayment-15 ShingleLayment-E
ASTM D226
Type II
ASTM D4869
Type IV
Accelerated Aging AC188 Pass Pass N/A N/A
UV Exposure AC188 Pass Pass N/A N/A
Pliability D226 Pass Pass Pass Pass
Liquid Water Transmissions ASTM D4869 Pass Pass N/A Pass
Loss on Heating (%) ASTM D228 1 0 max 4 max 6
Thickness ASTM D3767 8.70 5.40 — —
Temperature Range AC 188 67°F – 230°F -70°F – 212°F — —
Permeance ASTM E96 desiccant method 0.10 0.07 — —
Breaking Strength (lbf/in-width)
Control ASTM D146 89/89 73/56 40/20 40/20
Installation:
Both Grip-Rite ShingleLayment
®
Lightweights™ shall be
installed in compliance with the codied requirements
for ASTM D226, D4869 or underlayment for the type of
prepared roof covering to be installed.
Instructions:
Re-fasten any loose decking panels and check for
protruding nail heads. Sweep the substrate thoroughly
to remove any dust and debris prior to application.
Corrosion-resistant fasteners shall be plastic cap nails
or staples with a minimum nominal 1 in. diameter head.
The use of cap staples should be limited to installations
that will be covered by the nal roong system within
30-days as the membrane will be less resistive to the
elements which may result in blow-off.
Grip-Rite fasteners are recommended. Ensure fasteners
are installed at 90 degree angle to the deck with ush
contact between the plastic cap and the upper surface
of the underlayment. Where local code requires metal
cap washers, Grip-Rite Tin-Caps are recommended.
The use of staples or any other fastener without a 1 in.
diamter cap will void the Limited Warranty.
Grip-Rite ShingleLayment Lightweights shall be installed
horizontally with the printed side up, and with 4 in.
horizontal laps and 6 in. vertical laps. Horizontal laps
shall be in a shingle pattern, running with the ow of water.
Single Layer; Roof Slope > 4:12:
Starting at the eave, fasten the eave edge 8 in. OC and
vertical laps 8 in. OC, and 24 in. OC down the center of
the roll. Continue upslope in a similar manner, maintaining
minimum 4 in. horizontal and minimum 6 in. vertical laps.
Fasten 8 in. OC at horizontal laps and 8 in. OC at vertical
laps and 24 in. OC down the center of the roll. Ensure
all vertical laps are staggered at least 3 ft. apart. In high
wind zones (V-asd > 110 mph 3 second gust design
wind speed), increase the fastening schedule to 4 in. OC
at horizontal laps, 4 in. OC at vertical laps, and 24 in. OC
down the middle of the roll in the eld of the roof.
Double Layer; 2:12 < Roof Slope < 4:12:
Starting at the eave, fasten the eave-edge of a half-width
starter-strip 8 in. OC and vertical laps 8 in. OC Continue
upslope in a similar manner, with minimum 24 in.
horizontal laps and minimum 6 in. vertical laps. Fasten 8
in. OC along the low edge and 8 in. OC at vertical laps and
24 in. OC down the center of the roll. Ensure all vertical
laps are staggered at least 3 ft. apart. In high wind zones
(> 110 mph 3 second gust design wind speed), increase
the fastening schedule to 4 in. OC at horizontal laps, 4 in.
OC at vertical laps, and 24 in. OC down the middle of the
roll in the eld of the roof.
Installation for batten-secured roof cover:
When battens are installed over Grip-Rite ShingleLayment,
the underlayment need only be preliminarily attached
in advance of batten installation. Ensure preliminary
underlayment attachment does not interfere with batten
locations. Where seams or joints require sealant or
adhesive, use only high quality, low solvent asbestos
free plastic roong cement meeting ASTM D4586, Type
I. Install a leak barrier of ASTM D1970 or approved
equal at vulnerable leak areas, including but not limited
to eaves, valleys, rakes, skylights and dormers. At eaves
and valleys, install the leak barrier prior to installation of
ShingleLayment. Along the rake, install ShingleLayment
leaving 6 to 8 in. of the deck exposed, and then install
the leak barrier over the ShingleLayment and exposed
decking. At other areas, install the leak barrier over the
ShingleLayment.
Specications subject to change without notice.
ShingleLayment
®
Lightweight Synthetic Underlayments
ShingleLayment
®
Lightweight Synthetic Underlayments
Precautions & Limitations:
Depending on roof pitch and surface conditions (wet, dusty, frost), the coefcient of friction may change, and can become
slippery. Use caution.
Use caution when walking on roof deck and use OSHA compliant fall protection.
Do not walk or stand on ShingleLayment-E or ShingleLayment-15 until it is attached to roof deck according to installation
instructions.
Shingle print pattern is not intended for use as an installation grid for nal roong surface shingles.
ShingleLayment-E and ShingleLayment-15 are not designed as a primary roof covering. Exposure beyond 30-days without nal
roof covering may subject the sheet to jobsite abuse, chemical exposure, and severe weather.
ShingleLayment-E and ShingleLayment-15 may not be used in any exposed application such as crickets, exposed valleys,
or exposed roof to wall details.
Attic spaces must be property ventilated in accordance with the local Building Code.
Minimum roof pitch: 2:12 (9.4°).
Physical Properties
Properties Standard ShingleLayment-15 ShingleLayment-E
ASTM D226
Type II
ASTM D4869
Type IV
Accelerated Aging AC188 Pass Pass N/A N/A
UV Exposure AC188 Pass Pass N/A N/A
Pliability D226 Pass Pass Pass Pass
Liquid Water Transmissions ASTM D4869 Pass Pass N/A Pass
Loss on Heating (%) ASTM D228 1 0 max 4 max 6
Thickness ASTM D3767 8.70 5.40 — —
Temperature Range AC 188 67°F – 230°F -70°F – 212°F — —
Permeance ASTM E96 desiccant method 0.10 0.07 — —
Breaking Strength (lbf/in-width)
Control ASTM D146 89/89 73/56 40/20 40/20
Installation:
Both Grip-Rite ShingleLayment
®
Lightweights™ shall be
installed in compliance with the codied requirements
for ASTM D226, D4869 or underlayment for the type of
prepared roof covering to be installed.
Instructions:
Re-fasten any loose decking panels and check for
protruding nail heads. Sweep the substrate thoroughly
to remove any dust and debris prior to application.
Corrosion-resistant fasteners shall be plastic cap nails
or staples with a minimum nominal 1 in. diameter head.
The use of cap staples should be limited to installations
that will be covered by the nal roong system within
30-days as the membrane will be less resistive to the
elements which may result in blow-off.
Grip-Rite fasteners are recommended. Ensure fasteners
are installed at 90 degree angle to the deck with ush
contact between the plastic cap and the upper surface
of the underlayment. Where local code requires metal
cap washers, Grip-Rite Tin-Caps are recommended.
The use of staples or any other fastener without a 1 in.
diamter cap will void the Limited Warranty.
Grip-Rite ShingleLayment Lightweights shall be installed
horizontally with the printed side up, and with 4 in.
horizontal laps and 6 in. vertical laps. Horizontal laps
shall be in a shingle pattern, running with the ow of water.
Single Layer; Roof Slope > 4:12:
Starting at the eave, fasten the eave edge 8 in. OC and
vertical laps 8 in. OC, and 24 in. OC down the center of
the roll. Continue upslope in a similar manner, maintaining
minimum 4 in. horizontal and minimum 6 in. vertical laps.
Fasten 8 in. OC at horizontal laps and 8 in. OC at vertical
laps and 24 in. OC down the center of the roll. Ensure
all vertical laps are staggered at least 3 ft. apart. In high
wind zones (V-asd > 110 mph 3 second gust design
wind speed), increase the fastening schedule to 4 in. OC
at horizontal laps, 4 in. OC at vertical laps, and 24 in. OC
down the middle of the roll in the eld of the roof.
Double Layer; 2:12 < Roof Slope < 4:12:
Starting at the eave, fasten the eave-edge of a half-width
starter-strip 8 in. OC and vertical laps 8 in. OC Continue
upslope in a similar manner, with minimum 24 in.
horizontal laps and minimum 6 in. vertical laps. Fasten 8
in. OC along the low edge and 8 in. OC at vertical laps and
24 in. OC down the center of the roll. Ensure all vertical
laps are staggered at least 3 ft. apart. In high wind zones
(> 110 mph 3 second gust design wind speed), increase
the fastening schedule to 4 in. OC at horizontal laps, 4 in.
OC at vertical laps, and 24 in. OC down the middle of the
roll in the eld of the roof.
Installation for batten-secured roof cover:
When battens are installed over Grip-Rite ShingleLayment,
the underlayment need only be preliminarily attached
in advance of batten installation. Ensure preliminary
underlayment attachment does not interfere with batten
locations. Where seams or joints require sealant or
adhesive, use only high quality, low solvent asbestos
free plastic roong cement meeting ASTM D4586, Type
I. Install a leak barrier of ASTM D1970 or approved
equal at vulnerable leak areas, including but not limited
to eaves, valleys, rakes, skylights and dormers. At eaves
and valleys, install the leak barrier prior to installation of
ShingleLayment. Along the rake, install ShingleLayment
leaving 6 to 8 in. of the deck exposed, and then install
the leak barrier over the ShingleLayment and exposed
decking. At other areas, install the leak barrier over the
ShingleLayment.
Specications subject to change without notice.
ShingleLayment
®
Lightweight Synthetic Underlayments
ShingleLayment
®
Lightweight synthetic underlayments
GRSLLBRO
03/2014
Introducing two new
lightweight synthetic roong
underlayments, designed
to replace #15 saturated
asphalt felt.
Product Name:
Grip-Rite ShingleLayment-E
®
Grip-Rite ShingleLayment-15
®
Manufacturer:
PrimeSource Building Products, Inc.
1321 Greenway Drive, Irving, TX 75038
800-676-7777
www.primesourcebp.com
www.grip-rite.com
Product Description:
ShingleLayment-E is a lightweight version of our
proven Grip-Rite ShingleLayment. Woven 8 x 7 scrim
Polypropylene substrate coated on the walking surface
with a non-skid TPO. ShingleLayment-E has high tensile
strength to resist blow off from high wind exposure.
ShingleLayment-E can be used under any mechanically
attached asphalt shingle application.
ShingleLayment-15 is a woven 10 x 10 scrim
polypropylene substrate coated on the walking surface
with a spun bonded non-woven that provides non-skid
traction. ShingleLayment-15 has high tensile
strength to resist blow-off from high wind exposure.
ShingleLayment-15 can be used under any mechanically
attached asphalt shingle application.
Application:
Both products are designed for use on steep slope
roofs beneath asphalt shingles as an alternate to
ASTM D226, Type I or II or ASTM D4869 asphalt felts.
Both are a water shedding device designed to reduce
the occurrence of leaks caused by wind-driven rain
penetrating the primary roof system coverings
as well as a temporary cover on exposed roof decks.
These new synthetics outperform felt in every way – they roll out at, hold a chalk line, have a non-skid surface,
are mold resistant, and resist tear and cracking.
ShingleLayment Lightweights™ are backed by a limited warranty – felt paper doesn’t come close.
Finish the job right with Grip-Rite Eave & Valley Protector
™
and Grip-Rite Fasteners
®
.
Grip-Rite ShingleLayment
®
is distributed by PrimeSource Building Products, Inc.
© 2014 PrimeSource Building Products, Inc.
800-676-7777
www.grip-rite.com
www.primesourcebp.com
SKU Description
Size
Color
Weight/
Roll
Rolls/
Pallet
Pallets/
Truckload
Rolls/
TruckloadArea Dimensions
SLG4250GRE ShingleLayment-E 10 SQ 4 ft. x 250 ft. Gray 19.5 lb. 64 30 1,920
SL154250GR ShingleLayment-15 10 SQ 4 ft. x 250 ft. Gray 22.5 lb. 49 35 1,715
ShingleLayment-E
- Gray
ShingleLayment-15
- Gray
The time to convert from asphalt felt is NOW, with the new Grip-Rite
ShingleLayment Lightweight series of synthetic underlayments.
Features & Approvals:
Both Products
10 SQ coverage
Superior tear resistance
UV treated for 180 day exposure
5 times lighter than #15 felt
Contains no asphalt
Mold & crack resistant
Printed nail and overlap pattern
AC 188
ASTM D226 (non-asphalt properties)
ASTM D4869 (non-asphalt properties)
ASTM E96 (non-asphalt properties)
CAN CSA 123.3-05 (non-asphalt properties)
ShingleLayment-E
Non skid TPO walking surface
10 year warranty
Exclusive shingle print pattern
ShingleLayment-15
Non-skid SBPP surface
10 year limited warranty
Installer print pattern
-
1
-
2
-
3
-
4
Grip-Rite SLG4250GRE Installation guide
- Type
- Installation guide
- This manual is also suitable for
Grip-Rite SLG4250GRE is a lightweight synthetic underlayment designed to replace #15 saturated asphalt felt. It is a water shedding device designed to reduce the occurrence of leaks caused by wind-driven rain penetrating the primary roof system coverings as well as a temporary cover on exposed roof decks.
Grip-Rite SLG4250GRE is 10 SQ coverage and has superior tear resistance. It is UV treated for 180 day exposure and is 5 times lighter than #15 felt. It contains no asphalt and is mold and crack resistant. It has a printed nail and overlap pattern and is AC 188 approved. It meets ASTM D226 (non-asphalt properties), ASTM D4869 (non-asphalt properties), ASTM E96 (non-asphalt properties), and CAN CSA 123.3-05 (non-asphalt properties) standards.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Gibraltar Building Products GE12G Operating instructions
-
Rust-Oleum 347428 User manual
-
Dot Metal Products RE15B Operating instructions
-
Construction Metals RE15B Operating instructions
-
Construction Metals 11398 Operating instructions
-
BLACK JACK 6150-9-30 Installation guide
-
Construction Metals 3W4BR Installation guide
-
-
-