Grip-Rite TINTAGD5 Operating instructions

Grip-Rite
Brand
Grip-Rite
Model
TINTAGD5
Type
Operating instructions

This manual is also suitable for

Features :
provides a unique finished look to
exposed roof surfaces. Patent pending.
Titanium dioxide white coating provides an energy saving
emissive layer that reduces heat penetration.
Tear resistant high tensile strength woven PP substrate that
does not distort or belly like spun-bonded sheets.
UV resistant.
More than 5 times lighter than 30 lbs felt.
Roll coverage is 4.6 times greater than felt.
Non-skid TPO coating with high coefficient of friction.
Printed nail pattern for easy installation.
20-year limited warranty.
Available in two energy efficient colors, white or tan.
Lighter colors reduce fabric cycling (expansion and
contraction) thus reducing nail hole elongation.
Contains no asphalt.
þShingle print pattern
þ
þ
þ
þ
þ
þ
þ
þ
þ
þ
þ
Shingle Pattern TanDesert
Shingle Pattern White
Installer Print White Installer Print TanDesert
The only roofing underlayment with the high
performance of a synthetic underlayment, and the
finished look of a shingled roof.
1. Product Name:
2. Manufacturer:
3. Product Description:
exclusive shingle-look
print pattern
â
Available in energy efficient white or tan,
outperforms felt, is installer friendly, and provides both durable
temporary cover and long lasting water shedding protection .
â
Grip-Rite ShingleLayment Synthetic Underlayment
PrimeSource Building Products, Inc.
1321 Greenway Drive, Irving, TX 75038
800-676-7777
www.primesourcebp.com
www.grip-rite.com
Composition:
â â
Grip-Rite ShingleLayment synthetic underlayment is a
lightweight, woven polypropylene underlayment coated with a
non-skid TPO. ShingleLayment possesses very high tensile and
tear strength that resists tearing, ripping and blow offs from high
wind exposure. ShingleLayment can be used in any code
compliant mechanically attached roofing application.
Application:
Grip-Rite ShingleLayment synthetic underlayment is used on
steep-slope roofs beneath shingles, battened tiles, metal roofing,
slate, wood shake & shingle, and simulated slate/shake prepared
roof coverings as an alternate to ASTM D226, Type I or II or ASTM
D4869 asphalt felts.
Grip-Rite ShingleLayment synthetic underlayment is a water
shedding device designed to reduce the occurrence of leaks
caused by wind driven rain penetrating primary roof system
coverings, as well as damaged roof coverings, and as temporary
cover on exposed roof systems.
Grip-Rite ShingleLayment synthetic underlayment is available
with standard installer print pattern or
(Patent Pending). Both print patterns feature
installation and nailing grids for easy, accurate application.
Grip-Rite ShingleLayment synthetic underlayment increases
applicator productivity thanks to its low weight per roll, and
superior 10 sq. roll coverage .
Grip-Rite ShingleLayment synthetic underlayment can be
exposed to natural UV for up to 180 days.
Severe weather, jobsite
damage, chemical exposure or other conditions may shorten
exposure life.
ShingleLayment
GRSLBRO
06/2012
®
Grip-Rite ShingleLayment® is distributed by PrimeSource Building Products, Inc.
Grip-Rite ShingleLayment
OVE RLAP LI NE
OVE RLAP LI NE
OVE RLAP LI NE
OVE RLAP LI NE OVE RLAP LI NE
110.7 44mm( 4.36 in )
51.32 8 (2 in.)
51.32 8 (2 in.)
Grip-Rite ShingleLayment
101 6mm(4 0in.)
203 .2mm( 8in.)
203 .2mm( 8in.)
111 7.6mm ( 44 in.)
121 9.2 mm (4 8 in.)
SHI NGLE PR INT PAT TERN IS N OT INTE NDED FO R USE AS AN I NSTAL LATIO N GRID FO R FINAL R OOFIN G SURFA CE SHIN GLES
SHI NGLE PR INT PAT TERN IS N OT INTE NDED FO R USE AS AN I NSTAL LATIO N GRID FO R FINAL R OOFIN G SURFA CE SHIN GLES
Underwriters Laboratories
Verified to ICC-ES AC10 and AC 304
Underwriters Laboratories
Verified to ICC-ES AC10 and AC 304
ICC-ES ESR #2945 ICC-ES ESR #2945
OVE RLAP LI NE
OVE RLAP LI NE
OVE RLAP LI NE
OVE RLAP LI NE OVE RLAP LI NE
110.7 44mm( 4.36 in )
51.32 8 (2 in.)
51.32 8 (2 in.)
Underwriters Laboratories
Verified to ICC-ES AC10 and AC 304
Underwriters Laboratories
Verified to ICC-ES AC10 and AC 304
Grip-Rite ShingleLaymentGrip-Rite ShingleLayment
101 6mm(4 0in.)
203 .2mm( 8in.)
203 .2mm( 8in.)
111 7.6mm ( 44 in.)
121 9.2 mm (4 8 in.)
SHI NGLE PR INT PAT TERN IS N OT INTE NDED FO R USE AS AN I NSTAL LATIO N GRID FO R FINAL R OOFIN G SURFA CE SHIN GLES
SHI NGLE PR INT PAT TERN IS N OT INTE NDED FO R USE AS AN I NSTAL LATIO N GRID FO R FINAL R OOFIN G SURFA CE SHIN GLES
ICC-ES ESR #2945 ICC-ES ESR #2945
110.7 44mm( 4.36 in )
51.32 8 (2 in.)
51.32 8 (2 in.)
110.7 44mm( 4.36 in )
101 6mm(4 0in.)
203 .2mm( 8in.)
203 .2mm( 8in.)
111 7.6mm ( 44 in.)
121 9.2 mm (4 8 in.)
16. 054”
2.1 33”
Underwriters Laboratories
Verified to ICC-ES AC10
and AC 304
Grip-Rite ShingleLaymentICC-ES ESR #2945
Underwriters Laboratories
Verified to ICC-ES AC10
and AC 304
Grip-Rite ShingleLaymentICC-ES ESR #2945
110.7 44mm( 4.36 in )
51.32 8 (2 in.)
51.32 8 (2 in.)
110.7 44mm( 4.36 in )
101 6mm(4 0in.)
203 .2mm( 8in.)
203 .2mm( 8in.)
111 7.6mm ( 44 in.)
121 9.2 mm (4 8 in.)
16. 054”
2.1 33”
Underwriters Laboratories
Verified to ICC-ES AC10
and AC 304
Grip-Rite ShingleLaymentICC-ES ESR #2945
Underwriters Laboratories
Verified to ICC-ES AC10
and AC 304
Grip-Rite ShingleLaymentICC-ES ESR #2945
Print Patterns
®
Synthetic Roofing Underlayment
®
GRC58A Cap Stapler
GRC58A
Cap
Stapler
®
ShingleLayment Rolls
SKU
Size
Print
Color
Weight/
Roll
Pallets/
Truckload
Area
Dimensions
SLW4100GRI
4 Square
4 ft. x 100 ft.
Installer
White
13 lb.
36
SLT4100GRI
4 Square
4 ft. x 100 ft.
Installer
Desert Tan
13 lb.
36
SLW4100GRS
4 Square
4 ft. x 100 ft.
Shingle
White
13 lb.
36
SLT4100GRS
4 Square
4 ft. x 100 ft.
Shingle
Desert Tan
13 lb.
36
SLW4250GRI
10 Square
4 ft. x 100 ft.
Installer
White
30 lb.
36
SLT4250GRI
10 Square
4 ft. x 100 ft.
Installer
Desert Tan
30 lb.
36
SLW4250GRS
10 Square
4 ft. x 100 ft.
Shingle
White
30 lb.
36
SLT4250GRS
10 Square
4 ft. x 100 ft.
Shingle
Desert Tan
30 lb.
36
800-676-7777
www.grip-rite.com
www.primesourcebp.com
BUILDING PRODUCTS, INC.
© 2012 PrimeSource Building Products, Inc.
â â
Grip-Rite ShingleLayment
installed horizontally with the printed side up, and with 4-inch
horizontal laps and 6-inch vertical laps. Horizontal laps shall be in
a shingle pattern, running with the flow of water.
Single Layer; Roof Slope > 4:12:
Starting at the eave, fasten the eave edge 8-inch o.c. and vertical
laps 8-inch o.c., and 24-inch o.c. down the center of the roll.
Continue upslope in a similar manner, maintaining minimum 4-
inch horizontal and minimum 6-inch vertical laps. Fasten 8-inch
o.c. at horizontal laps and 8-inch o.c. at vertical laps and 24-inch
o.c. down the center of the roll. Ensure all vertical laps are
staggered at least 3-feet apart.
In high wind zones (> 110 mph 3-second gust design wind
speed), increase the fastening schedule to 4-inch o.c. at horizontal
laps, 4-inch o.c. at vertical laps, and 24-inch o.c. down the middle
of the roll in the field of the roof.
Double Layer; 2:12 < Roof Slope < 4:12:
Starting at the eave, fasten the eave-edge of a half-width starter-
strip 8-inch o.c. and vertical laps 8-inch o.c. Continue upslope in
a similar manner, with minimum 24-inch horizontal laps and
minimum 6-inch vertical laps. Fasten 8-inch o.c. along the low
edge and 8-inch o.c. at vertical laps and 24-inch o.c. down the
center of the roll. Ensure all vertical laps are staggered at least 3-
feet apart. In high wind zones (> 110 mph 3-second gust design
wind speed), increase the fastening schedule to 4-inch o.c. at
horizontal laps, 4-inch o.c. at vertical laps, and 24-inch o.c. down
the middle of the roll in the field of the roof.
synthetic underlayment shall be
6. Precautions & Limitations:
þ
þ
þ
þ
þ
þ
þ
þ
Depending on roof pitch and surface conditions (wet, dusty,
frost), the coefficient of friction may change, and can
become slippery. Use Caution.
Use caution
compliant fall protection.
Do not walk or stand on ShingleLayment until it is attached
to roof deck according to Installation Instructions.
Shingle print pattern is not intended for use as an
installation grid for final roofing surface shingles.
Grip-Rite ShingleLayment synthetic underlayment is not
designed as a primary roof covering. Exposure beyond sixty
days without final roof covering may subject the sheet to
jobsite abuse, chemical exposure, and severe weather.
Grip-Rite ShingleLayment synthetic underlayment may not be
used in any exposed application such as crickets, exposed
valleys, or exposed roof to wall details.
Attic spaces must be property ventilated in accordance with
the local Building Code.
Minimum roof pitch: 2:12 (9.4°).
when walking on roof deck and use OSHA
4. Standards and Approvals:
þ
þ
þ
þ
þ
þ
þ
þ
5. Installation:
ICC-ESR #2945
Miami-Dade NOA 09-0527.01 8/26/09
Florida Statewide Product Approval File No. FL12510
AC 188
ASTM D226
ASTM D4869 Type IV
Class A Fire Tested
CAN CSA A123
â
â
Grip-Rite ShingleLayment
i
nstalled in compliance with the codified requirements for ASTM
D226, D4869 or D6757 underlayment for the type of prepared roof
covering to be installed.
Re-fasten any loose decking panels, and check for protruding nail
heads. Sweep the substrate thoroughly to remove any dust and
debris prior to application.
Corrosion resistant fasteners shall be plastic cap nails or staples
with a minimum nominal 1-inch diameter head. The use of cap
staples should be limited to installations that will be covered by the
final roofing system within 60 days as the membrane will be less
resistive to the elements which may result in blow-off.
â
Grip-Rite fasteners are recommended. Ensure fasteners are
installed at 90-degree angle to the deck with flush contact between
the plastic cap and the upper surface of the underlayment. Where
â
local code requires metal cap washers, Grip-Rite Tin-Caps are
recommended.
synthetic underlayment shall be
For batten-secured roof cover installations:
When battens are installed over
synthetic underlayment, the underlayment need only be
preliminarily attached in advance of batten installation. Ensure
preliminary underlayment attachment does not interfere with
batten locations.
Where seams or joints require sealant or adhesive, use only high
quality, low solvent asbestos free plastic roofing cement meeting
ASTM D4586, Type I.
Install a leak barrier of ASTM D1970 or approved equal at
vulnerable leak areas, including but not limited to eaves, valleys,
rakes, skylights and dormers. At eaves and valleys, install the leak
â
barrier prior to installation of Grip-Rite . Along the rake, install
â
Grip-Rite ShingleLayment leaving 6 to 8-inch of the deck
â
exposed, and then install the leak barrier over the Grip-Rite and
exposed decking. At other areas, install the leak barrier over the
â
Grip-Rite ShingleLayment .
â â
Grip-Rite ShingleLayment
Synthetic Roofing Underlayment
®
â â
Physical Properties of Grip-Rite ShingleLayment Synthetic Underlayment
Properties
Standard
®
Grip-Rite
ASTM D226 Type II
ASTM D4869 Type IV
Accelerated Aging
AC188
Pass
N/A
N/A
UV Exposure
AC188
Pass
N/A
N/A
Pliability
D226
Pass
Pass
Pass
Liquid Water Transmissions
ASTM D4869
Pass
N/A
Pass
Loss on Heating (%)
ASTM D228
0.4
4
6
Thickness
ASTM D3767
8.5 mils
—
—
Temperature Range
AC188
-55° C (-67° F) – 110° C (230° F)
—
—
Permeance
ASTM E 96 Desiccant method
.03 PERMS
—
—
Tensile Strength (lb./ft./in.)
Control
ASTM D828
116/113
N/A
N/A
After Aging
—
116/99
N/A
N/A
After UV
—
117/94
N/A
N/A
Breaking Strength (lb./ft.)
Control
ASTM D146
118/116
40/20
40/20
â â
Grip-Rite ShingleLayment
installed horizontally with the printed side up, and with 4-inch
horizontal laps and 6-inch vertical laps. Horizontal laps shall be in
a shingle pattern, running with the flow of water.
Single Layer; Roof Slope > 4:12:
Starting at the eave, fasten the eave edge 8-inch o.c. and vertical
laps 8-inch o.c., and 24-inch o.c. down the center of the roll.
Continue upslope in a similar manner, maintaining minimum 4-
inch horizontal and minimum 6-inch vertical laps. Fasten 8-inch
o.c. at horizontal laps and 8-inch o.c. at vertical laps and 24-inch
o.c. down the center of the roll. Ensure all vertical laps are
staggered at least 3-feet apart.
In high wind zones (> 110 mph 3-second gust design wind
speed), increase the fastening schedule to 4-inch o.c. at horizontal
laps, 4-inch o.c. at vertical laps, and 24-inch o.c. down the middle
of the roll in the field of the roof.
Double Layer; 2:12 < Roof Slope < 4:12:
Starting at the eave, fasten the eave-edge of a half-width starter-
strip 8-inch o.c. and vertical laps 8-inch o.c. Continue upslope in
a similar manner, with minimum 24-inch horizontal laps and
minimum 6-inch vertical laps. Fasten 8-inch o.c. along the low
edge and 8-inch o.c. at vertical laps and 24-inch o.c. down the
center of the roll. Ensure all vertical laps are staggered at least 3-
feet apart. In high wind zones (> 110 mph 3-second gust design
wind speed), increase the fastening schedule to 4-inch o.c. at
horizontal laps, 4-inch o.c. at vertical laps, and 24-inch o.c. down
the middle of the roll in the field of the roof.
synthetic underlayment shall be
6. Precautions & Limitations:
þ
þ
þ
þ
þ
þ
þ
þ
Depending on roof pitch and surface conditions (wet, dusty,
frost), the coefficient of friction may change, and can
become slippery. Use Caution.
Use caution
compliant fall protection.
Do not walk or stand on ShingleLayment until it is attached
to roof deck according to Installation Instructions.
Shingle print pattern is not intended for use as an
installation grid for final roofing surface shingles.
Grip-Rite ShingleLayment synthetic underlayment is not
designed as a primary roof covering. Exposure beyond sixty
days without final roof covering may subject the sheet to
jobsite abuse, chemical exposure, and severe weather.
Grip-Rite ShingleLayment synthetic underlayment may not be
used in any exposed application such as crickets, exposed
valleys, or exposed roof to wall details.
Attic spaces must be property ventilated in accordance with
the local Building Code.
Minimum roof pitch: 2:12 (9.4°).
when walking on roof deck and use OSHA
4. Standards and Approvals:
þ
þ
þ
þ
þ
þ
þ
þ
5. Installation:
ICC-ESR #2945
Miami-Dade NOA 09-0527.01 8/26/09
Florida Statewide Product Approval File No. FL12510
AC 188
ASTM D226
ASTM D4869 Type IV
Class A Fire Tested
CAN CSA A123
â
â
Grip-Rite ShingleLayment
i
nstalled in compliance with the codified requirements for ASTM
D226, D4869 or D6757 underlayment for the type of prepared roof
covering to be installed.
Re-fasten any loose decking panels, and check for protruding nail
heads. Sweep the substrate thoroughly to remove any dust and
debris prior to application.
Corrosion resistant fasteners shall be plastic cap nails or staples
with a minimum nominal 1-inch diameter head. The use of cap
staples should be limited to installations that will be covered by the
final roofing system within 60 days as the membrane will be less
resistive to the elements which may result in blow-off.
â
Grip-Rite fasteners are recommended. Ensure fasteners are
installed at 90-degree angle to the deck with flush contact between
the plastic cap and the upper surface of the underlayment. Where
â
local code requires metal cap washers, Grip-Rite Tin-Caps are
recommended.
synthetic underlayment shall be
For batten-secured roof cover installations:
When battens are installed over
synthetic underlayment, the underlayment need only be
preliminarily attached in advance of batten installation. Ensure
preliminary underlayment attachment does not interfere with
batten locations.
Where seams or joints require sealant or adhesive, use only high
quality, low solvent asbestos free plastic roofing cement meeting
ASTM D4586, Type I.
Install a leak barrier of ASTM D1970 or approved equal at
vulnerable leak areas, including but not limited to eaves, valleys,
rakes, skylights and dormers. At eaves and valleys, install the leak
â
barrier prior to installation of Grip-Rite . Along the rake, install
â
Grip-Rite ShingleLayment leaving 6 to 8-inch of the deck
â
exposed, and then install the leak barrier over the Grip-Rite and
exposed decking. At other areas, install the leak barrier over the
â
Grip-Rite ShingleLayment .
â â
Grip-Rite ShingleLayment
Synthetic Roofing Underlayment
®
â â
Physical Properties of Grip-Rite ShingleLayment Synthetic Underlayment
Properties
Standard
®
Grip-Rite
ASTM D226 Type II ASTM D4869 Type IV
Accelerated Aging
AC188
Pass N/A N/A
UV Exposure
AC188
Pass
N/A N/A
Pliability D226
Pass
Pass
Pass
Liquid Water Transmissions
ASTM D4869
Pass
N/A
Pass
Loss on Heating (%)
ASTM D228
0.4
4
6
Thickness
ASTM D3767 8.5 mils
—
—
Temperature Range AC188
-55° C (-67° F) – 110° C (230° F) — —
Permeance
ASTM E 96 Desiccant method
.03 PERMS —
—
Tensile Strength (lb./ft./in.)
Control
ASTM D828
116/113 N/A
N/A
After Aging —
116/99
N/A N/A
After UV —
117/94 N/A
N/A
Breaking Strength (lb./ft.)
Control ASTM D146
118/116 40/20
40/20
Features :
provides a unique finished look to
exposed roof surfaces. Patent pending.
Titanium dioxide white coating provides an energy saving
emissive layer that reduces heat penetration.
Tear resistant high tensile strength woven PP substrate that
does not distort or belly like spun-bonded sheets.
UV resistant.
More than 5 times lighter than 30 lbs felt.
Roll coverage is 4.6 times greater than felt.
Non-skid TPO coating with high coefficient of friction.
Printed nail pattern for easy installation.
20-year limited warranty.
Available in two energy efficient colors, white or tan.
Lighter colors reduce fabric cycling (expansion and
contraction) thus reducing nail hole elongation.
Contains no asphalt.
þShingle print pattern
þ
þ
þ
þ
þ
þ
þ
þ
þ
þ
þ
Shingle Pattern TanDesert
Shingle Pattern White
Installer Print White Installer Print TanDesert
The only roofing underlayment with the high
performance of a synthetic underlayment, and the
finished look of a shingled roof.
1. Product Name:
2. Manufacturer:
3. Product Description:
exclusive shingle-look
print pattern
â
Available in energy efficient white or tan,
outperforms felt, is installer friendly, and provides both durable
temporary cover and long lasting water shedding protection .
â
Grip-Rite ShingleLayment Synthetic Underlayment
PrimeSource Building Products, Inc.
1321 Greenway Drive, Irving, TX 75038
800-676-7777
www.primesourcebp.com
www.grip-rite.com
Composition:
â â
Grip-Rite ShingleLayment synthetic underlayment is a
lightweight, woven polypropylene underlayment coated with a
non-skid TPO. ShingleLayment possesses very high tensile and
tear strength that resists tearing, ripping and blow offs from high
wind exposure. ShingleLayment can be used in any code
compliant mechanically attached roofing application.
Application:
Grip-Rite ShingleLayment synthetic underlayment is used on
steep-slope roofs beneath shingles, battened tiles, metal roofing,
slate, wood shake & shingle, and simulated slate/shake prepared
roof coverings as an alternate to ASTM D226, Type I or II or ASTM
D4869 asphalt felts.
Grip-Rite ShingleLayment synthetic underlayment is a water
shedding device designed to reduce the occurrence of leaks
caused by wind driven rain penetrating primary roof system
coverings, as well as damaged roof coverings, and as temporary
cover on exposed roof systems.
Grip-Rite ShingleLayment synthetic underlayment is available
with standard installer print pattern or
(Patent Pending). Both print patterns feature
installation and nailing grids for easy, accurate application.
Grip-Rite ShingleLayment synthetic underlayment increases
applicator productivity thanks to its low weight per roll, and
superior 10 sq. roll coverage .
Grip-Rite ShingleLayment synthetic underlayment can be
exposed to natural UV for up to 180 days.
Severe weather, jobsite
damage, chemical exposure or other conditions may shorten
exposure life.
ShingleLayment
GRSLBRO
06/2012
®
Grip-Rite ShingleLayment® is distributed by PrimeSource Building Products, Inc.
Grip-Rite ShingleLayment
OVE RLAP LI NE
OVE RLAP LI NE
OVE RLAP LI NE
OVE RLAP LI NE OVE RLAP LI NE
110.7 44mm( 4.36 in )
51.32 8 (2 in.)
51.32 8 (2 in.)
Grip-Rite ShingleLayment
101 6mm(4 0in.)
203 .2mm( 8in.)
203 .2mm( 8in.)
111 7.6mm ( 44 in.)
121 9.2 mm (4 8 in.)
SHI NGLE PR INT PAT TERN IS N OT INTE NDED FO R USE AS AN I NSTAL LATIO N GRID FO R FINAL R OOFIN G SURFA CE SHIN GLES
SHI NGLE PR INT PAT TERN IS N OT INTE NDED FO R USE AS AN I NSTAL LATIO N GRID FO R FINAL R OOFIN G SURFA CE SHIN GLES
Underwriters Laboratories
Verified to ICC-ES AC10 and AC 304
Underwriters Laboratories
Verified to ICC-ES AC10 and AC 304
ICC-ES ESR #2945 ICC-ES ESR #2945
OVE RLAP LI NE
OVE RLAP LI NE
OVE RLAP LI NE
OVE RLAP LI NE OVE RLAP LI NE
110.7 44mm( 4.36 in )
51.32 8 (2 in.)
51.32 8 (2 in.)
Underwriters Laboratories
Verified to ICC-ES AC10 and AC 304
Underwriters Laboratories
Verified to ICC-ES AC10 and AC 304
Grip-Rite ShingleLaymentGrip-Rite ShingleLayment
101 6mm(4 0in.)
203 .2mm( 8in.)
203 .2mm( 8in.)
111 7.6mm ( 44 in.)
121 9.2 mm (4 8 in.)
SHI NGLE PR INT PAT TERN IS N OT INTE NDED FO R USE AS AN I NSTAL LATIO N GRID FO R FINAL R OOFIN G SURFA CE SHIN GLES
SHI NGLE PR INT PAT TERN IS N OT INTE NDED FO R USE AS AN I NSTAL LATIO N GRID FO R FINAL R OOFIN G SURFA CE SHIN GLES
ICC-ES ESR #2945 ICC-ES ESR #2945
110.7 44mm( 4.36 in )
51.32 8 (2 in.)
51.32 8 (2 in.)
110.7 44mm( 4.36 in )
101 6mm(4 0in.)
203 .2mm( 8in.)
203 .2mm( 8in.)
111 7.6mm ( 44 in.)
121 9.2 mm (4 8 in.)
16. 054”
2.1 33”
Underwriters Laboratories
Verified to ICC-ES AC10
and AC 304
Grip-Rite ShingleLaymentICC-ES ESR #2945
Underwriters Laboratories
Verified to ICC-ES AC10
and AC 304
Grip-Rite ShingleLaymentICC-ES ESR #2945
110.7 44mm( 4.36 in )
51.32 8 (2 in.)
51.32 8 (2 in.)
110.7 44mm( 4.36 in )
101 6mm(4 0in.)
203 .2mm( 8in.)
203 .2mm( 8in.)
111 7.6mm ( 44 in.)
121 9.2 mm (4 8 in.)
16. 054”
2.1 33”
Underwriters Laboratories
Verified to ICC-ES AC10
and AC 304
Grip-Rite ShingleLaymentICC-ES ESR #2945
Underwriters Laboratories
Verified to ICC-ES AC10
and AC 304
Grip-Rite ShingleLaymentICC-ES ESR #2945
Print Patterns
®
Synthetic Roofing Underlayment
®
GRC58A Cap Stapler
®
ShingleLayment Rolls
SKU
Size
Print
Color
Weight/
Roll
Rolls/
Pallet
Pallets/
Truckload
Area
Dimensions
SLW4100GRI
4 Square
4 ft. x 100 ft. Installer
White 13 lb.
90
36
SLT4100GRI
4 Square
4 ft. x 100 ft. Installer
Desert Tan
13 lb.
90 36
SLW4100GRS
4 Square
4 ft. x 100 ft. Shingle
White
13 lb.
90 36
SLT4100GRS
4 Square
4 ft. x 100 ft. Shingle
Desert Tan
13 lb.
90
36
SLW4250GRI
10 Square 4 ft. x 100 ft.
Installer
White
30 lb.
35 36
SLT4250GRI
10 Square 4 ft. x 100 ft.
Installer
Desert Tan
30 lb.
35
36
SLW4250GRS
10 Square 4 ft. x 100 ft.
Shingle
White
30 lb.
35 36
SLT4250GRS
10 Square 4 ft. x 100 ft.
Shingle
Desert Tan
30 lb. 35 36
800-676-7777
www.grip-rite.com
www.primesourcebp.com
BUILDING PRODUCTS, INC.
© 2012 PrimeSource Building Products, Inc.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Grip-Rite TINTAGD5 Operating instructions

Grip-Rite
Brand
Grip-Rite
Model
TINTAGD5
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents