Fiveo VIRGO 100 Owner's manual

Type
Owner's manual
VIRGO 100
PORTABLE COMBO
SYSTEM
Elettronica Montarbo srl Via O. Pigini, 8 - 62010 Montelupone (MC) - ITALY - T + 39 0733 227 1
F + 39 0733 227 250 - [email protected] - montarbo.com - Company under control of EKO Music Group SpA
VIRGO 100
VIRGO 100
Important Safety Instructions
- 2 -
VIRGO 100
- 3 -
Table of Contents
1. FEATURES
2. DESCRIPTION OF VARIOUS PARTS
3. RECEIVER DISPLAY
4. METAL HAND MIC
5. BELTPACK MIC
6. TECHNICAL SPECIFICATION
7. CONNECTION DIAGRAM
8. BLOCK DIAGRAM
9. ACCESSORIES
10. CAUTION
4
5
8
9
10
14
15
16
17
17
VIRGO 100
- 4 -
FEATURES
● User- friendly operation.
It is equipped with professional wireless receiving module with quartz locked, output
volume control when the wireless module works, MP3 player and AUX output can be
muted.
● Built-in one microphone input and one AUX input with individual volume controls.
● Built-in one AUX input and one line output.
● Built-in two tone (treble, bass) and master volume controls.
● Digital MP3 player with clear sound, easy operation.
● Class D power amplifier and professional two way crossover.
● Professional mounting hole for heightening this unit to meet the requirements.
● Wheel and handle for easy carriage.
● Two power supplies: AC 115-120V/220-240V, DC22.2V (LITHIUM BATTERY)
● When AC works, Power LED lights up; when battery works, Power LED and battery level
LED light up.
When AC inputs, the battery will charge automatically, and Recharge indicator will light
red. After full recharged, the indicator will light green.
VIRGO 100
- 5 -
DESCRIPTION OF VARIOUS PARTS
Woofer
Tweeter
Antenna
Handle
Handle could only be pushed and pulled
to transport the unit on the wheels.
Do NOT use this handle to lift
the unit up!
VIRGO 100
- 6 -
DESCRIPTION OF VARIOUS PARTS
UP
● Short press: Select the "UP" frequency.
● Long Press and hold the button for 3 seconds up, enter into IR pairing mode,
simultaneously the CH code will flash, then release the button and paired with MIC IR.
● Press and hold the ”UP” button 6 seconds or more, the frequency/CH will be
progressively increased. Then it enter IR pairing mode and simultaneously CH code
will start to flash after the button is released.
SET
● Short press for one time: Enter the volume controlling mode and the volume can be
adjusted by “UP” and “DOWN”.
Short press for two times: Enter SQUELCH controlling mode, SQUELCH can be
adjusted by “UP” and “DOWN”.
DOWN
Short press: Select the "DOWN" frequency.
● Press and hold the ”Down” button for 3 seconds, enter swept mode and begin to
sweep the whole frequency rapidly, releasing the button, the system will select the
cleanest channels from these frequencies swept automatically. Then enter into IR
pairing mode and CH code start to flash. At this time it will pair with MIC IR.
Button for popping out the module
CH1 Volume Control
This knob is used to control the CH1 level.
CH2 Volume Control
This knob is used to control the CH2 level.
TREBLE CONTROL
This knob is used to control the treble level with range going from +10dB--10dB.
BASS CONTROL
This knob is used to control the bass level with range going from +10dB--10dB.
Master Volume control
This knob is used to control the Master level.
Battery level LED
Battery level indicator
Recharge Indicator LED
Charge indicator: lights red when charging and lights green after fully charged.
Power LED
The Power LED lights up when the amplifier is powered ON.
CH1 LINE and MIC Switch
MIC inputs when pressing MIC Switch, line inputs when the MIC Switch is popped out.
LINE1 or MIC1 Input
They are used for both balanced and unbalanced inputs.
1
2
3
4
5
6
7
8
9
10
11
12
14
13
VIRGO 100
- 7 -
DESCRIPTION OF VARIOUS PARTS
CH2 AUX Input
It is used for AUX input.
LINE OUT
It is connected to recorder or mixer.
Voice priority
When this button is engaged, CH1, RF1&RF2 will have priority over AUX and MP3
AUX and MP3 will be muted.
USB Volume control
This knob is used to control the USB player volume.
Play / Pause
Record
Press this button once and you are ready to record. Press the button again to start
record. To stop press the POWER button.
Previous song
Play the previous song.
Next song
Play the next song.
Repeat
Select between different repeat modes (repeat all, repeat one song, shuffle and
mormal playback.)
POWER (ON/OFF)
Press and hold this button for switch ON or OFF VIRGO 100.
USB PORT
For connecting with USB memory.
POWER SWITCH
If the switch is set to the position “ON”, both AC and DC supply is connected, AC
supply has priority over DC supply. When there is no AC voltage input, it will
automatically switch to DC supply and the unit keeps working during AC/DC is
switching. If the switch is set to the position “OFF”, the whole unit doesn’t work.
AC INPUT
115-120V 50-60Hz, 220-240V 50-60Hz. Please check the voltage available in your
country and how the voltage for unit is configured before attempting to connect your
unit to the main AC.
Wheel
Rubber Feet
Charging indicator LED
Lights red when charging and lights green when the battery is fully charged.
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
VIRGO 100
- 8 -
RECEIVER DISPLAY
● Standby Mode display
● Volume control display
● SQUELCH control display
SQUELCH control SQUELCH indicator
Volume control Mute or unmute AF level indicator
Frequency Channel
Current Frequency
Mic Mute indicator
Battery charge level
AF power indicator
RF power indicator
1
2
3
4
5
6
1 2 3
1 2
VIRGO 100
- 9 -
METAL HAND MIC
Status indicator
This LED displays the operation mode:
1
Power/Mute Switch
Press and hold to turn the unit on or off. Press
and release to mute or unmute the transmitter.
Battery Cover
Unscrew the battery cover and slide down to
open the MIC battery compartment.
2
3
GREEN
RED
Flashing RED
Normal Operation
Mute
Low Power
VIRGO 100H
VIRGO 100H
VIRGO 100B
VIRGO 100
- 10 -
METAL HAND MIC
BELTPACK MIC
Battery Holder
Open the battery holder by pressing the tab and lifting the cover, and insert two
standard AA (LR6) batteries here, being sure to observe the correct polarity.
WARNING: Do not insert the batteries backwards; doing so can cause severe
damage to the MIC and will void your warranty.
Input GAIN Control
This control adjusts the transmitter input sensitivity. For optimal performance, you
can use the included screwdriver to set the input GAIN control.
IR Lens
This window is used to capture the infrared signal sent from the receiver to the
transmitter during the IR UP/DOWN operation. The battery cover must be open and
the IR Lens facing towards the receiver to load the selected channel.
Plastic Screwdriver
Designed for adjusting the MIC input GAIN (See #5 Input GAIN Control HH).
Charging indicator LED
Lights red when charging and lights green after fully charged.
4
5
6
7
8
Antenna
This permanently attached transmitter antenna should be fully extended during
normal operation.
Status Indicator
This LED displays the operation mode:
Power/Mute Switch
Press and hold to turn the unit on or off. Press and release to mute or unmute the
transmitter.
GREEN
RED
Flashing RED
Normal Operation
Mute
Low Power
1
2
3
VIRGO 100
- 11 -
BELTPACK MIC
MINI 4P CONNECTOR
a). Pin 1, GND
b). Pin 2, Phantom power supply for condenser microphone
c). Pin 3, designed for guitar, bass and keyboards
d). Pin 4, designed for dynamic or condenser microphone
IR Receiving Section
This window is used to capture the infrared signal sent from the receiver during the
IR UP/DOWN to channelize the transmitter.
Input GAIN Control
This control adjusts the transmitter input sensitivity for microphone and instruments
inputs.
Driver
Designed for adjusting the MIC input GAIN.
4
5
6
7
VIRGO 100B
VIRGO 100
- 12 -
BELTPACK MIC
With the transmitter powered off, install two fresh AA batteries into the MIC.
Leave the battery compartment open.
Turn on the transmitter by pressing and holding Power switch; the indicator LED will light
green.
Press the UP/DOWN button on the front of the receiver to choose an available channel.
The channel number will increase by two digit, from 00-99. Once the last channel has
been reached, the count will cycle back to 00.
Press and hold the UP button for 2 seconds to send the channel information to the
transmitter via infrared transmission.
Press and hold DOWN button for 2 seconds and then start to scan full frequency and
finally automatically choose clearnest channel to send channel info to transmitter via
infrared transmission.
Press and hold the UP button and the channel will be fast forward.
Press and hold the DOWN button and the channel will be fast backward.
VIRGO 100H
VIRGO 100H
VIRGO 100B
VIRGO 100B
VIRGO 100
- 13 -
BELTPACK MIC
Place the transmitter about 15~30cm from the front of the receiver with the transmitter’s
IR window facing the display on the front panel of the receiver.
Press and hold the receiver UP/DOWN button to set the transmitter to the same channel
as the receiver via infrared transmission.
When the transmission is complete, the receiver will receive RF signal and tone key from
the transmitter.
The RF indicator of the screen will light on the front panel of the receiver.
VIRGO 100B
VIRGO 100
- 14 -
TECHNICAL SPECIFICATION
Power Supply AC: 100V~120V / 220~240V / Battery: 25.9V(lithium battery)
System Type 2-Way Active Vented Speaker
Transducer Low 10” Woofer, 1.5” Voice coil
Transducer driver 1” Ferrite Driver, 1” Voice coil
Horn Coverage H°x V° 90°H x 45°V
Frequency Response (-6dB) 65Hz-20KHz
Crossover Frequency 5KHz
Max SPL 117dB Max
AMP Power Output RMS: 200W(AC) (LF-Class D 135W&HF-Class D 65W)
Input sensitivity
CH1 MIC: -35dBu(±1dBu)
CH1 LINE: -3dBu(±1dBu)
CH1 AUX: -10dBu(±1dBu)
Equalizer Controls
BASS: ±10dB(at 100Hz)
TREBLE: ±10dB(at 10K)
Master Volume Control; MIC&LINE Switch; MIC1 - AUX each
Volume Control: Volce Priority Switch; Power Indicators;
Recharged Indicators; Battery Level Indicators;
External Controls
Voice Priority MIC 1 and Wireless
Battery charge time Less than 4 hours
Battery operating time More than 4 hours (Regular Play)
Wireless Frequency band 800MHZ
Built-in player MP3
Enclosure Construction Plastic cabinet, Trapezoidal, Metal grill, Rubber foot, handle
Mounting 36mm standard pole-mount
Dimensions(HxWxD) 568(H) x 300(W) x 300(D) mm
Net Weight 12.8kg
Volume 3.9CFT
VIRGO 100
- 15 -
CONNECTION DIAGRAM
Amplifier
Microphone
Tuner
CD Player
Power Cord
VIRGO 100
- 16 -
Block Diagram
VIRGO 100
- 17 -
ACCESSORIES
CAUTION
1. Do not use any volatile solvents such as toluene, Alcohol or gasoline for safety, keep
product clean and free from dust.
2. Do not put this equipment in direct sunlight.
3. Do not expose this equipment to rain when used outdoor.
4. After using, press the power switch to turn off the power.
5. If the equipment is not used for a long time, please recharge the battery to at least
80% of its full level to lengthen the battery life.
Power Cord
Wireless Microphone
User Manual
Battery
Warranty Card
x 1
x 2
x 1
x 1
x 1
VIRGO 100
Elettronica Montarbo srl Via O. Pigini, 8 - 62010 Montelupone (MC) - ITALY - T + 39 0733 227 1
F + 39 0733 227 250 - [email protected] - montarbo.com - Company under control of EKO Music Group SpA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Fiveo VIRGO 100 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI