Ancona AN-1157 User manual

Brand: Ancona

Model: AN-1157

Category: Cooker hoods

Type: User manual

Range Hood

WRP430 & WRP436

User Manual

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

Carefully read the important information

regarding installation, safety and maintenance.

Keep these instructions for future reference.

MAAN-1156-01

— 2 —

INSTALLERS - Start Here

Safety Instructions are on pages 4 and 5 and

Installation Instructions are on pages 9 to 15.

Please perform these steps:

1. Read the safety instructions.

2. Read all instructions in the Installation section of

this manual BEFORE installing the range hood.

3. Remove all packing materials.

4. When nished, make sure to leave these instructions with the consumer.

5. Installation is to be done by a qualied technician only. However, the

ultimate responsibility for proper installation falls to the owner.

Product failure due to improper installation is not covered under the Warranty.

CONSUMERS - Start Here

Safety Instructions are on pages 4 and 5 and Operating Instructions are

on pages 16 and 17.

Please perform these steps:

1. Read the safety instructions.

2. Read all instructions in the manual BEFORE operating the range hood.

3. Remove all packing materials.

4. Installation is to be done by a qualied technician only. However, the

ultimate responsibility for proper installation falls to the owner.

Product failure due to improper installation is not covered under the Warranty.

Before You Begin

Hardware Note: For safety reasons, range hood mounting screws and anchors will not be

included due to the variation of cabinetry constructions and wall material. Please consult your

installation specialist regarding the optimal type of mounting screws and wall anchors to suit your

home’s construction.

— 3 —

Before You Begin ............................................................................................................................... 2

Table of Contents .............................................................................................................................. 3

Important Safety Information ............................................................................................................ 4

Included Parts ................................................................................................................................... 6

Range Hood Dimensions .................................................................................................................. 7

Specications .................................................................................................................................... 7

Mounting Brackets ............................................................................................................................ 8

Installation ......................................................................................................................................... 9

Step 1 - Read the Safety Instructions ............................................................................................ 9

Step 2 - Unpack Range Hood and Prepare Tools .......................................................................... 9

Step 3 - Plan Desired Location ...................................................................................................... 9

Step 4 - Test Unit Functions .......................................................................................................... 9

Step 5 - Venting Installation Guidelines ....................................................................................... 10

Step 6 - Preparations ................................................................................................................... 12

Step 7 - Installing the hood mounting bracket ............................................................................ 12

Step 8 - Installing the upper chimney bracket ............................................................................. 12

Step 9 - Venting ........................................................................................................................... 13

Step 10 - Mount Range Hood Onto Wall ..................................................................................... 13

Step 11 - Install Chimney ............................................................................................................. 13

Step 12 - Connect Ductwork ....................................................................................................... 14

Step 13 - Connect to AC.............................................................................................................. 14

Step 14 - Install Filters ................................................................................................................. 15

Operation ........................................................................................................................................ 16

Time/Delay (Double Function Button) .......................................................................................... 16

Lighting ........................................................................................................................................ 16

Blower .......................................................................................................................................... 16

Maintenance.................................................................................................................................... 17

Replacing the Light Bulbs ............................................................................................................ 17

Range Hood Assembly ................................................................................................................... 18

Assembly ......................................................................................................................................... 19

Circuit Diagram ............................................................................................................................ 19

Blower Assembly ......................................................................................................................... 19

Electrical Assembly ...................................................................................................................... 19

Use and Care Information ............................................................................................................... 20

Table of Contents

— 4 —

Important Safety Information

• Theinstallationinthismanualisintended

for qualied installers, service technicians or

persons with a similar qualied background.

Installation must be done by qualied

professionals and in accordance with all

applicable codes and standards, including

re-rated construction.

•

The range hood may have very sharp

edges; please wear protective gloves if it is

necessary to remove any parts for installing,

cleaning or servicing.

•

Activating any switch to ON position before

completing installation may cause damage or

electric shock.

• Duetothesizeofthisrangehood,atwo

person installation is recommended.

To reduce the risk of re, electric shock, or

injury to persons:

• Forgeneralventilatinguseonly.DO NOT use

toexhausthazardousorexplosivematerials

and vapors.

• WARNING: To Reduce The Risk Of Fire Or

Electric Shock, Do Not Use This Fan With Any

Solid-State Speed Control Device.

• Thecombustionairowneededforsafe

operation of fuel-burning equipment may be

affected by this unit’s operation. Follow the

heating equipment manufacturer’s guideline

and safety standards such as those published

by the National Fire Protection Association

(NFPA), and the American Society of Heating,

Refrigeration and Air Conditioning Engineers

(ASHRAE), and other local code authorities.

• Beforeservicingorcleaningtheunit,switch

power off at service panel and lock the service

disconnecting means to prevent power from

being switched on accidentally. When the

service disconnecting means cannot be

locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

• Cleangrease-ladensurfacesfrequently.To

optimizeperformanceandtodisperseair

properly, make sure to vent air outside. DO

NOT vent exhaust into spaces between walls,

crawl spaces, ceilings, attics or garages.

•

Ducted fans MUST always be vented to

the outdoors.

• ThisunitMUSTbegroundedandusedwith

metal ductwork only.

• Sufcientairisneededforpropercombustion

and exhausting of gases through the duct to

prevent back drafting.

• Whencuttingordrillingintowallorceiling,be

careful not to damage electrical wiring or other

hidden utilities.

• Allelectricalwiringmustbeproperlyinstalled,

insulated and grounded.

•

Old ductwork should be cleaned or replaced

if necessary to avoid the possibility of a

grease re.

•

Check all joints on ductwork to ensure

proper connection; all joints should be

properly taped using a certied aluminum

or foil tape.

• Usethisunitonlyinthemannerintended

by the manufacturer. If you have questions,

contact the vendor.

READ AND SAVE THESE

INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Read and follow all instructions before using the range hood to prevent the risk of re, electric shock,

personal injury, or damage when using the range hood or appliances with the range hood. This guide

does not cover all possible conditions that may occur. Always contact your service technician or

manufacturer about problems that you do not understand.

— 5 —

Important Safety Information

WARNING: TO REDUCE RISK OF A RANGE

TOP GREASE FIRE:

a) Never leave surface units unattended at high

settings. Boilovers cause smoking and greasy

spillovers that may ignite. Heat oils slowly on

low or medium settings.

b) Always turn range hood ON when cooking at

highheatorwhenambéingfood(i.e.Crepes

Suzette,CherriesJubilee,etc.).

Clean ventilating fans frequently. Grease should

not be allowed to accumulate on fan or lter.

Before servicing or cleaning unit, unplug and

disconnect the hood from the power supply.

d)Useproperpansize.Alwaysusecookware

appropriateforthesizeofthesurfaceelement.

WARNING: TO REDUCE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP

GREASE FIRE, OBSERVE THE FOLLOWING *

a) S

MOTHER FLAMES with a close-tting

lid, cookie sheet, or metal tray, then turn

off the burner. BE CAREFUL TO PREVENT

BURNS.Iftheamesdonotgoout

immediately, EVACUATE AND CALL THE

FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may

be burned.

c) DO NOT USE WATER, including wet dishcloths

or towels - a violent steam explosion will result.

d) Use an extinguisher ONLY if:

1) You know you have a Class A, B, C

extinguisher, and you already know how to

operate it.

2) The re is small and contained in the area

where it is started.

3) The re department is being called.

You can ght the re with your back to an exit.

* Based on “Kitchen Fire Safety Tips”

published by NFPA

To reduce the risk of injury to persons in the

event of a gas leaks:

• Extinguishanyopename.

•

DO NOT turn on the lights or any type of appliance.

• Openalldoorsandwindowstodispersethe

gas. If you still smell gas, call the gas company

and re department.

Your safety and the safety of others is very

important. We have provided many important

safety messages in this manual and on your

appliance. Always read and obey all safety

messages. All safety messages outline any

potentialhazards,howtoreducethechanceof

injury, and possible risks if the instructions are not

followed.

READ AND SAVE THESE

INSTRUCTIONS

— 6 —

Included Parts

Main Housing

Upper Chimney

Lower Chimney

Upper Chimney Bracket

Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to

the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding

the optimal type of mounting screws and wall anchors to suit your home’s construction.

Lower Chimney Bracket

Hood Mounting Bracket

30” Filters (x2)

36” Filters (x3)

4 x Damper Screws (A)

4 x Chimney Screws (B)

— 7 —

Range Hood Dimensions

Specications

Body Design Stainless Steel

Power Rating 120V/60Hz(cETLusCertied)

Total Input Power 215 W (210W+2*2.5W)

Motor Input Power 210 W

Amperage 1.8 A

Speed Control Levels 3 Speeds

Interference Protection Radio Frequency Interference Protected

Noise Level (50db)/(55db)/(60db)

Motors Single Motor

Control LCD touch control panel

Filtration Aluminum lter, stainless steel surface

Illumination 2x2.5W LED 4V maximum

Fan Type Centrifugal squirrel cage

VentingSize Top, 6 inches round

30” (76.2 cm) or 36” (91.4 cm)

— 8 —

Mounting Brackets

— 9 —

STEP 1

Read the Safety Instructions

• It is very important to read the safety instructions on pages 4 and 5.

IMPORTANT: It is the installer’s responsibility to comply with installation clearances.

STEP 2

Unpack Range Hood and Prepare Tools

• Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6.

• DO NOT remove the protective lm covering the appliance until the installation is fully completed.

• Consult a qualied and trained installer or check local codes for makeup air requirement, if any.

STEP 3

Plan Desired Location

• Plan a desirable location that ts all requirements in the Safety and Installation sections of this manual. Plan where

and how the ductwork will be installed.

• A straight or short duct run will allow the unit to perform most efciently. Long duct runs, elbows and transitions

willreducetheperformanceoftheunit.Eachelbowisequivalentto5to10feetofstraightrun.Propersizeduct

work should be 7” (178 mm) in diameter.

• To reach a 9 foot ceiling make sure hood is installed 30 inches from cooking surface. If you have a ceiling

greater than 9ft, please visit anconahome.com to order a chimney extension.

• If ductwork is already installed: ensure ductwork is free from debris and measures 7”

(178 mm)

(1” reducers may be

used but more than 1” will overwork the motor and the unit will not function properly).

STEP 4

Test Unit Functions

• Plug the unit in and test all of the functions before installing.

• Placetherangehoodonaat,stablesurface.Connecttherangehoodtoadesignatedstandardoutlet(120-Volt,60Hz,

AC only) and turn on the range hood. Verify all operations of the range hood by referring to

Range Hood Operations.

• Turn power On in control panel.

• Check all lights and fan operations.

WARNINGS:

• PleasemakesuretoreadALLsafetyinstuctionsonpages4and5.

• Usetwoormorepeopletomoveandinstallrangehood.

• Failuretofollowtheseinstructionscanresultinseriousinjury.

Installation

— 10 —

Installation

STEP 5

Venting Installation Guidelines

• The following steps are for exterior ventilation.

• If you require a ductless installation, please visit anconahome.com to purchase a recirculation kit.

Height and Clearance

IMPORTANT:

•

Vent system must terminate to the outside (roof or side wall).

• DONOT

terminate the vent system in an attic or other

enclosed area.

• DONOTuse4”(10.2cm)laundry-typewallcaps.

• Usemetal/aluminumventonly.Arigidmetal/aluminum

vent is recommended.

• DONOTuseaplasticvent.

• Alwayskeeptheductcleantoensureproperairflow.

• Calculatethefollowingfiguresbeforeinstallation:

1. Distance from the floor to the ceiling

2. Distance between the floor and the countertop/stove

A distance of 24” to 30” is recommended between

stove top and the bottom of range hood. 30” minimum

is required for gas stove tops.

4. Height of hood and duct cover.

For the most efficient & quiet operation:

• Itisrecommendedthattherangehoodbevented

vertically through the roof through 10” (15.3 cm) or

bigger round metal/aluminum vent work.

• Thesizeoftheventshouldbeuniform.

• Usenomorethanthree90°elbows.

•

Make sure there is a minimum of 24” (61 cm) of

straight vent between the elbows if more than one

elbow is used.

• DONOTinstalltwoelbowstogether.

•

The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

• Theventsystemmusthaveadamper.Ifrooforwall

cap has a damper, you may remove damper flaps from

damper to increase air flow.

• Onlyoneflangeisneededintheaireductsystem,

either on top of the motor or outside.

•

Use silver tape or duct tape to seal all joints in the

vent system.

•

Use caulking to seal exterior wall or roof opening

around the cap.

24” (610 mm) Min / 30” (762 mm) Max

To reach 9 ft ceiling, make sure

range hood is installed at least

30” (762 mm) from cooking surface.

— 11 —

IMPORTANT:

•

A minimum of 6” round or 3-1/4 x 10” rectangular duct

(purchased separately) must be used to maintain maximum

airflow efficiency.

• Alwaysuserigidtypemetal/aluminumductsifavailableto

maximizeairflowwhenconnectingtoprovidedduct.

• PleaseuseDuctRunCalculationbelowtocompute

total available duct run when using elbows, transitions

and caps.

• ALWAYS,whenpossible,reducethenumberor

transitions and turns. If long duct run is required,

increaseductsizefrom6”to7”or8”.Ifareducer

is used, install a long reducer instead of a pancake

reducer.Reducingductsizewillrestrictairflowand

decreaseairflow,thusreduceductsizeasfaraway

from opening as possible.

• Ifturnsortransitionsarerequired,installasfaraway

from opening and as far apart, between two (2), as

possible.

• Minimummountheightbetweenstovetoptohood

bottom should be no less than 24-inch for electric cook

tops and minimum of 30-inch for gas stove tops and no

higher than 30-inch for electric cook tops.

• Itisimportanttoinstallthehoodatthepropermounting

height. Hoods mounted too low could result in heat

damageandfirehazard;whilehoodsmountedtoohigh

may be hard to reach and will lose its performance and

efficiency.

• Ifavailable,alsorefertostovetopmanufacturer’s

height clearance requirements and recommended

hood mounting height above range.

Installation

• This range hood is factory set for venting through the roof or wall.

• Ventworkcanterminateeitherthroughtherooforwall.Toventthroughawall,a90°elbowisneeded.

IMPORTANT:

• NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or

garages. All exhaust must be ducted to the outside.

• Use metal/aluminum duct work only.

• Fasten all connections with sheet metal screws and tape all joints with certied Silver Tape or Duct Tape.

• Use caulking to seal exterior wall or roof opening around the cap.

— 12 —

Installation

STEP 6

Preparations:

NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.

• Determine and mark the center line on the ceiling or wall where the range hood will be installed.

• Make sure there is proper clearance within the ceiling or wall for exhaust vent.

• Duetotheweightandsizeofthisunit,pleasemakesurethatthesupportsystemorframeworkbeingusedisstableand

secure in the ceiling or wall.

• Put a thick, protective covering over counter top, cook top or range to protect from damage or dirt.

• Removeanyhazardousobjectsaroundtheareawheninstalling.

CAUTION

If moving the cooking range is necessary to install the hood, turn OFF the power on an electric range at the main

electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE

STEP 7

Installing the hood mounting bracket

• Use a pencil to mark on the wall the desired placement of the range hood mounting screws.

• The range hood will be installed on top of this bracket (See Figure # 1).

• Using references in Height & Clearance on Page 10 and Measurements and Diagrams on Page 7, drill 3 holes that will

be used to x the lower mounting bracket.

STEP 8

Installing the upper chimney bracket

• Drill2holesaccordingtothesizeoftheuppermountingbracket.Theuppermountingbracketshouldbepositioned

ushwiththetopoftheoutsidechimney(SeeFigure1)

• Screw upper and hood mounting brackets in tightly.

190

115

Fig #1

Flush to the ceiling

— 13 —

Installation

STEP 10

Mount Range Hood Onto Wall

• Hang the range hood on the hooks of the lower

mounting bracket. (See Figure # 3)

• Screw the range hood to the wall.

CAUTION - Make sure the range hood is secure

before releasing!

STEP 9

Venting

• Fix the damper on the top vent of hood with 4 screws (A).

• If ventilation system is equipped with an external

air duct with a different diameter, apply a reduction

tting. However, for maximum performance and

safety, a 6” round ducting is recommended.

STEP 11

Install Chimney

• Place chimney on top of the main housing.

• Remove the protective coating from the upper chimney. Carefully slide the upper chimney down into the lower chimney.

• Use 2 screws (B) to x the two chimneys together with the lower chimney bracket, make sure upper chimney is moving

freely. (See Figure # 4)

• Screw the upper chimney to the upper mounting bracket (B). (See Figure # 5)

Fig #2

Fig #3

Fig #4

Fig #5

— 14 —

STEP 12

Connect Ductwork

• Attach ductwork to damper. Secure the ductwork with duct tape to make sure joints are secure and air- tight.

• Donotinstalltheducttapetootightlyasthismaypreventthedamperapsfromopeningwhichwilloverworkthemotor

and cause improper functioning of the unit.

• Fasten all connections with sheet metal screws and tape all joints with certied aluminum or foil tape. Use caulking to

seal exterior wall or roof opening around the cap.

STEP 13

Connect to AC

• Connect AC plug into a grounded AC outlet

having120V,60Hz.Placetheoutletatamaximum

distance of 33-1/2” (851 mm) from where the cord

exits on the hood.

3-Pronged Plug

Ground Plug

3-Prong Receptacle

IMPORTANT:

• Observeallgoverningcodesandordinances.

• It is the customer’s responsibility to contact a qualified electrical installer.

• Ifcodespermitandaseparategroundwireisused,itisrecommendedthataqualifiedelectriciandeterminethat

thegroundpathisadequate.A120-Volt,60Hz,AC-only,fusedelectricalsupplyisrequiredonaseparate15-amp

circuit, fused on both sides of the line.

• DONOTgroundtoagaspipe.

• Checkwithaqualifiedelectricianifyouarenotsurethattherangehoodisproperlygrounded.

• DONOThaveafuseintheneutralorgroundcircuit.

IMPORTANT: Save this Installation Guide for electrical inspector’s use.

GROUNDING INSTRUCTIONS:

• Thisappliancemustbegrounded.Intheeventofanelectricalshort-circuit,groundingreducestheriskofelectric

shock by providing an escape wire for the electric current.

• Thisapplianceisequippedwithacordhavingagroundingwirewithagroundingplug.Theplugmustbeplugged

into an outlet that is properly installed and grounded.

WARNING: Improper grounding can result in a risk of electric shock.

• Consultaqualifiedelectricianifthegroundinginstructionsarenotcompletelyunderstood,orifdoubtexistsasto

whether the appliance is properly grounded. DO NOT use an extension cord. If the power supply cord is too short,

have a qualified electrician install an outlet near the appliance.

• Therangehoodmustbeconnectedwithcopperwire/plugonly.Therangehoodshouldbeconnecteddirectlyto

the fused disconnect (or circuit breaker) box through flexible armored or non-metallic sheathed copper cable. UL/

CSA listed strain relief must be provided at each end of the power supply cable.

Installation

— 15 —

Installation

STEP 14

Install Filters

To install lters for the following four steps (See Figure # 6):

• Angle the lter into slots at the back of the hood.

• Push the button on handle of the lter.

• Release the handle once the lter ts into a resting position.

• Repeat to install all lters.

Cleaning Filters

IMPORTANT: Drain oil from bafes, spacers, lters, oil tunnels, oil containers before oil and residue overow!

• Removeallbafes,spacers,lters,greasetray,andoilcontainersanddiscardoilandresidue.

• Washwithwarmsoapywater.NOTE:Stainlesssteelbafes,spacersandoiltunnelaretoprackdishwashersafe.

• Dry thoroughly before replacing and follow directions for installation in reverse.

• Filters should be cleaned after every 30 hours of use.

• Should lters wear out due to age and prolonged use, replace with a new lter.

Fig #6

— 16 —

Operation

Time/Delay (Double Function Button)

Time Setting: This button is used to set time when lighting

and blower are not in use. Time is displayed in 24 hour

cycle. To set time;

Press the button (1) for 4 seconds. The rst two digits

willash.

Use the blower button (3) to increase and the lighting

button (2) to decrease.

Press the time/delay button (1) again, the last two

digitswillash.Usetheblowerbutton(3)toincrease

and the lighting button (2) to decrease.

Press the time/delay button (1) again to conrm and

exit time setting mode.

Delay Setting: When blower is in use, this button is the

delay setting button. To set delay;

Press the button (1). The delay is factory set at 5

minutes, but can be set from 1 up to 60 minutes.

Use blower button (3) to increase and lighting button

(2) to decrease. Countdown will be displayed on the

LCD screen and blower symbol will be activated.

Blower will continue to operate for the programmed

minutes and then will stop automatically (delay

setting mode does not affect lighting as it works

independently).Thelasttimeusedwillbememorized.

To cancel delay function, press time/delay button (1)

again, the blower will continue to operate and won’t

stop until ON/OFF button (4) is pressed.

To turn delay function and blower OFF at once, press

ON/OFF button (4).

Lighting

Pressing the lighting button (2) once will turn the

LCD screen on.

To turn the lights on, press the lighting button (2)

once more. Press it again to turn the lights OFF.

The LCD screen will turn automatically off after 15

seconds of inactivity (blower and/or lights).

Blower

The blower button (3) turns the blower on to three speed

settings: LOW, MEDIUM or HIGH.

Press the blower (3) or ON/OFF (4) button once to

turn the LCD screen on. Pressing the blower (3) or

ON/OFF (4) button once more will turn the blower on

at the last selected speed and blower symbol will be

activated.

To change the blower speed, press the blower

button (3) until the desired speed is obtained.

Press the ON/OFF button (4) to turn the blower OFF.

Thelastspeedusedwillbememorized.

— 17 —

Make sure the range hood is unplugged or turn OFF

breaker.

Open the lter and nd the spring of the light.

Push the spring and the lights will slip out.

CAUTION: BULB MAY BE HOT, PLEASE TAKE OUT

THE BULB WHEN THE BULB IS COMPLETELY

COOL!

Replace with a 4 Volt, 2.5Watt max, LED lights. Do

not touch replacement bulb with bare hands!

Turn ON breaker and range hood to test for

operation.

Maintenance

Replacing the Light Bulbs

IMPORTANT:

ALWAYS SWITCH OFF THE ELECTRICITY SUPPLY AT THE MAIN PANEL BEFORE CARRYING OUT ANY OPERATION

ON THE APPLIANCE.

— 18 —

Range Hood Assembly

Number Part Quantity

1 Recirculation Kit (Not

Included)

2 Duct Tube (Not

Included)

3 Upper chimney 1

4 Lower chimney 1

5 Bracket for Upper

chimney

6 Bracket for Lower

chimney

7 Vent/damper 1

8 Mounting bracket 1

9 Power cord 1

10 Housing assembly 1

11 Control panel

assembly

12 Electronic box 1

13 PCB board 1

14 Capacitor 1

15 Base of electronic

box

16 Transformer 1

17 Transformer box 1

18 Light panel assembly 1

19 LED Lights 2

20 Blower assembly 1

21 Charcoal support 2

22 Charcoal lter (Not

included)

23 Bracket for control

panel

24 Control panel 1

25 Filters 30”

Filters 36”

26 Screw bag 1

— 19 —

Assembly

Circuit Diagram

Blower Assembly

Electrical Assembly

Number Part

1 Grid

2 Blower

3 Impeller

4 Motor

Number Part

1 Electrical Box Base

2 PCB

3 Electrical Cover

4 Capacitor

5 Screw (ST3*10)

6 Screw (ST3*6)

— 20 —

Use and Care Information

Operations

• Read and understand all instructions and warnings in this manual before operating the appliance. Save these

instructions for future reference.

• Always leave safety grills and lters in place. Without these components, operating fans could catch on to hair, ngers

and loose clothing.

• NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into fans.

• NEVER leave cooking unattended. When frying, oil in the pan can easily overheat and catch re. The risk of self

combustion is higher when the oil has been used several times.

• NEVERcookon“open”amesundertherangehood.Checkdeep-fryersduringuse;superheatedoilmaybe

ammable.

Cleaning

• Thesaturationofgreasyresidueinthefanandltersmaycauseincreasedinammability.Keepunitcleanandfreeof

grease and residue build-up at all times to prevent possible res.

• Filters must be cleaned periodically and free from accumulation of cooking residue (see Cleaning Instructions below).

Old and worn lters must be replaced immediately.

• DO NOT operate fans when lters are removed. Never disassemble parts to clean without proper instructions.

Disassembly is recommended to be performed by qualied personnel only. Read and understand all instructions and

warnings in this manual before proceeding.

SAFETY WARNING: Never put your hand into area housing the fan while the fan is operating!

For optimal operation, clean range hood and all bafe/spacer/lter/grease tray/oil container regularly. Regular care

will help preserve the appearance of the range hood.

Cleaning Exterior Surfaces:

• Clean periodically with hot soapy water and clean cotton cloth. DO NOT use corrosive or abrasive detergent (e.g. Comet

Power Scrub®, EZ-Off® oven cleaner), or steel wool/scoring pads, which will scratch and damage the stainless steel

surface. For heavier soil use liquid degrease such as “Formula 409®” or “Fantastic®” brand cleaner.

• If hood looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the hood. Avoid getting

cleaning solution onto or into the control panel. Follow directions of the stainless steel cleaner. CAUTION: DO NOT

leave on too long as this may cause damage to hood nish. Use soft towel to wipe off the cleaning solution, gently

rub off any stubborn spots. Use dry soft towel to dry the hood.

• After cleaning, you may use non abrasive stainless steel polish such as 3M® or ZEP®, to polish and buff out the

stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.

• DO NOT allow deposits to accumulate or remain on the hood.

• DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.

• DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel

for extended periods. Many of these compounds contain chemicals, which

Page is loading ...

Ancona AN-1157 User manual

Brand: Ancona

Model: AN-1157

Category: Cooker hoods

Type: User manual

Download PDF

report

Ancona AN-1157 User manual

Ancona AN-1157 User manual

Related papers

Other documents