Ancona AN-1800 User manual

Ancona
Brand
Ancona
Model
AN-1800
Category
Cooker hoods
Type
User manual
— 2 —
INSTALLERS - Start Here
Safety Instructions are on pages 4 and 5 and
Installation Instructions are on pages 15 to 22.
Please perform these steps:
1. Read the safety instructions.
2. Read all instructions in the Installation section of
this manual BEFORE installing the range hood.
3. Remove all packing materials.
4. When nished, make sure to leave these instructions with the consumer.
5. Installation is to be done by a qualied technician only. However, the
ultimate responsibility for proper installation falls to the owner.
6.
Product failure due to improper installation is not covered under the Warranty.
CONSUMERS - Start Here
Safety Instructions are on pages 4 and 5 and Operating Instructions are
on pages 23, 24, 25 and 35.
Please perform these steps:
1. Read the safety instructions.
2. Read all instructions in the manual BEFORE operating the range hood.
3. Remove all packing materials.
4. Installation is to be done by a qualied technician only. However, the
ultimate responsibility for proper installation falls to the owner.
5.
Product failure due to improper installation is not covered under the Warranty.
Before You Begin
Hardware Note: For safety reasons, range hood mounting screws and anchors will not be
included due to the variation of cabinetry constructions and wall material. Please consult your
installation specialist regarding the optimal type of mounting screws and wall anchors to suit your
home’s construction.
— 3 —
Before You Begin ............................................................................................................................... 2
Table of Contents .............................................................................................................................. 3
Important Safety Information ............................................................................................................ 4
Included Parts ................................................................................................................................... 6
Range Hood Dimensions and Specications ................................................................................... 7
Mounting Brackets for Wall Hoods ................................................................................................. 13
Installation ....................................................................................................................................... 15
Step 1 - Read the Safety Instructions .......................................................................................... 15
Step 2 - Unpack Range Hood and Prepare Tools ........................................................................ 15
Step 3 - Plan Desired Location .................................................................................................... 15
Step 4 - Test Unit Functions ........................................................................................................ 15
Step 5 - Venting Installation Guidelines ....................................................................................... 16
Step 6 - Preparations ................................................................................................................... 18
Step 7A (wall hoods only) - Installing the Hood Mounting Bracket ............................................. 18
Step 8A (wall hoods only) - Installing the Upper Chimney Bracket ............................................. 18
Step 9A (wall hoods only) - Venting ............................................................................................. 19
Step 10A (wall hoods only) - Mount Range Hood onto Wall ........................................................ 19
Step 11A (wall hoods only) - Connect Ductwork ......................................................................... 19
Step 12A (wall hoods only) - Connect to AC ............................................................................... 19
Step 13A (wall hoods only) - Install Chimney ............................................................................... 20
Step 7B (cabinet hoods only) - Attaching Vent/Damper .............................................................. 21
Step 8B (cabinet hoods only) - Installing the Hood ..................................................................... 21
Step 9B (cabinet hoods only) - Electrical Connection ................................................................. 21
Step 10B (cabinet hoods only) - Venting ..................................................................................... 22
Step 14A / Step 11B (all models) - Install Filters ......................................................................... 22
Operation ........................................................................................................................................ 23
Power Settings ............................................................................................................................. 23
Lights ........................................................................................................................................... 23
Timer ............................................................................................................................................ 23
Maintenance.................................................................................................................................... 24
Replacing the Light Pucks ........................................................................................................... 24
Cleaning Filters ............................................................................................................................ 25
Troubleshooting............................................................................................................................... 25
Range Hood Assembly ................................................................................................................... 26
Assembly ......................................................................................................................................... 32
Circuit Diagram ............................................................................................................................ 32
Electrical Assembly ...................................................................................................................... 33
Blower Assembly ......................................................................................................................... 34
Use and Care Information ............................................................................................................... 35
Table of Contents
— 3 —
Before You Begin ............................................................................................................................... 2
Table of Contents .............................................................................................................................. 3
Important Safety Information ............................................................................................................ 4
Included Parts ................................................................................................................................... 6
Range Hood Dimensions and Specications ................................................................................... 7
Mounting Brackets for Wall Hoods ................................................................................................. 13
Installation ....................................................................................................................................... 15
Step 1 - Read the Safety Instructions .......................................................................................... 15
Step 2 - Unpack Range Hood and Prepare Tools ........................................................................ 15
Step 3 - Plan Desired Location .................................................................................................... 15
Step 4 - Test Unit Functions ........................................................................................................ 15
Step 5 - Venting Installation Guidelines ....................................................................................... 16
Step 6 - Preparations ................................................................................................................... 18
Step 7A (wall hoods only) - Installing the Hood Mounting Bracket ............................................. 18
Step 8A (wall hoods only) - Installing the Upper Chimney Bracket ............................................. 18
Step 9A (wall hoods only) - Venting ............................................................................................. 19
Step 10A (wall hoods only) - Mount Range Hood onto Wall ........................................................ 19
Step 11A (wall hoods only) - Connect Ductwork ......................................................................... 19
Step 12A (wall hoods only) - Connect to AC ............................................................................... 19
Step 13A (wall hoods only) - Install Chimney ............................................................................... 20
Step 7B (cabinet hoods only) - Attaching Vent/Damper .............................................................. 21
Step 8B (cabinet hoods only) - Installing the Hood ..................................................................... 21
Step 9B (cabinet hoods only) - Electrical Connection ................................................................. 21
Step 10B (cabinet hoods only) - Venting ..................................................................................... 22
Step 14A / Step 11B (all models) - Install Filters ......................................................................... 22
Operation ........................................................................................................................................ 23
Power Settings ............................................................................................................................. 23
Lights ........................................................................................................................................... 23
Timer ............................................................................................................................................ 23
Maintenance.................................................................................................................................... 24
Replacing the Light Pucks ........................................................................................................... 24
Cleaning Filters ............................................................................................................................ 25
Troubleshooting............................................................................................................................... 25
Range Hood Assembly ................................................................................................................... 26
Assembly ......................................................................................................................................... 32
Circuit Diagram ............................................................................................................................ 32
Electrical Assembly ...................................................................................................................... 33
Blower Assembly ......................................................................................................................... 34
Use and Care Information ............................................................................................................... 35
Table of Contents
— 4 —
Important Safety Information
• Theinstallationinthismanualisintended
for qualied installers, service technicians or
persons with a similar qualied background.
Installation must be done by qualied
professionals and in accordance with all
applicable codes and standards, including
re-rated construction.
•
The range hood may have very sharp
edges; please wear protective gloves if it is
necessary to remove any parts for installing,
cleaning or servicing.
•
Activating any switch to ON position before
completing installation may cause damage or
electric shock.
• Duetothesizeofthisrangehood,atwo
person installation is recommended.
To reduce the risk of re, electric shock, or
injury to persons:
• Forgeneralventilatinguseonly.DO NOT use
toexhausthazardousorexplosivematerials
and vapors.
• WARNING: To Reduce The Risk Of Fire Or
Electric Shock, Do Not Use This Fan With Any
Solid-State Speed Control Device.
• Thecombustionairowneededforsafe
operation of fuel-burning equipment may be
affected by this unit’s operation. Follow the
heating equipment manufacturer’s guideline
and safety standards such as those published
by the National Fire Protection Association
(NFPA), and the American Society of Heating,
Refrigeration and Air Conditioning Engineers
(ASHRAE), and other local code authorities.
• Beforeservicingorcleaningtheunit,switch
power off at service panel and lock the service
disconnecting means to prevent power from
being switched on accidentally. When the
service disconnecting means cannot be
locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
• Cleangrease-ladensurfacesfrequently.To
optimizeperformanceandtodisperseair
properly, make sure to vent air outside. DO
NOT vent exhaust into spaces between walls,
crawl spaces, ceilings, attics or garages.
•
Ducted fans MUST always be vented to
the outdoors.
• ThisunitMUSTbegroundedandusedwith
metal ductwork only.
• Sufcientairisneededforpropercombustion
and exhausting of gases through the duct to
prevent back drafting.
• Whencuttingordrillingintowallorceiling,be
careful not to damage electrical wiring or other
hidden utilities.
• Allelectricalwiringmustbeproperlyinstalled,
insulated and grounded.
•
Old ductwork should be cleaned or replaced
if necessary to avoid the possibility of a
grease re.
•
Check all joints on ductwork to ensure
proper connection; all joints should be
properly taped using a certied aluminum
or foil tape.
• Usethisunitonlyinthemannerintended
by the manufacturer. If you have questions,
contact the vendor.
READ AND SAVE THESE
INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Read and follow all instructions before using the range hood to prevent the risk of re, electric shock,
personal injury, or damage when using the range hood or appliances with the range hood. This guide
does not cover all possible conditions that may occur. Always contact your service technician or
manufacturer about problems that you do not understand.
— 5 —
Important Safety Information
WARNING: TO REDUCE RISK OF A RANGE
TOP GREASE FIRE:
a) Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
low or medium settings.
b) Always turn range hood ON when cooking at
highheatorwhenambéingfood(i.e.Crepes
Suzette,CherriesJubilee,etc.).
c)
Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or lter.
Before servicing or cleaning unit, unplug and
disconnect the hood from the power supply.
d)Useproperpansize.Alwaysusecookware
appropriateforthesizeofthesurfaceelement.
WARNING: TO REDUCE RISK OF INJURY TO
PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING *
a) S
MOTHER FLAMES with a close-tting
lid, cookie sheet, or metal tray, then turn
off the burner. BE CAREFUL TO PREVENT
BURNS.Iftheamesdonotgoout
immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may
be burned.
c) DO NOT USE WATER, including wet dishcloths
or towels - a violent steam explosion will result.
d) Use an extinguisher ONLY if:
1) You know you have a Class A, B, C
extinguisher, and you already know how to
operate it.
2) The re is small and contained in the area
where it is started.
3) The re department is being called.
4)
You can ght the re with your back to an exit.
* Based on “Kitchen Fire Safety Tips”
published by NFPA
To reduce the risk of injury to persons in the
event of a gas leaks:
• Extinguishanyopename.
•
DO NOT turn on the lights or any type of appliance.
• Openalldoorsandwindowstodispersethe
gas. If you still smell gas, call the gas company
and re department.
Your safety and the safety of others is very
important. We have provided many important
safety messages in this manual and on your
appliance. Always read and obey all safety
messages. All safety messages outline any
potentialhazards,howtoreducethechanceof
injury, and possible risks if the instructions are not
followed.
READ AND SAVE THESE
INSTRUCTIONS
— 6 —
Included Parts Wall Hoods
Main Housing
2 Filters
Upper Chimney
Lower Chimney
Upper Chimney Bracket
Hardware Note: For safety reasons, range hood mounting screws and anchors will not be included due to
the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding
the optimal type of mounting screws and wall anchors to suit your home’s construction.
2 + 1 Screws
Lower Chimney Bracket
Hood Mounting Bracket
Damperap
Included Parts Under Cabinet Hoods
Main Housing 2 Filters 4 + 1 ScrewsDamper
— 7 —
Range Hood Dimensions and Specications
50 cm (19.6 in.)
74.5 cm (29.3 in.)
3.8 cm
(1.5 in.)
39 - 74 cm
(15.3 - 29.1 in.)
26 cm
(10.2 in.)
20.9 cm
(8.2 in.)
17.2 cm
(6.75 in.)
Specications
Body Design Stainless Steel
Power Rating 120V/60Hz(cETLusCertied)
Total Input Power 88 W (85 W + 2 × 1.5 W)
Motor Input Power 85 W
Amperage 0.8 A
Speed Control Levels 3 Speeds
Interference Protection Radio Frequency Interference Protected
Motors Single Motor
Control Mechanical control panel
Filtration Aluminium lter
Illumination 2 × 1.5 W LED
Fan Type Single chamber quiet
VentingSize Top, 6 inches (15.3 cm) round
AN-1158
— 8 —
Specications
Body Design Stainless Steel
Power Rating 120V/60Hz(cETLusCertied)
Total Input Power 193 W (190 W + 2 × 1.5 W)
Motor Input Power 190 W
Amperage 1.6 A
Speed Control Levels 3 Speeds
Interference Protection Radio Frequency Interference Protected
Motors Single Motor
Control Mechanical control panel
Filtration Aluminium lter
Illumination 2 × 1.5 W LED
Fan Type Single squirrel cage
VentingSize Top, 6 inches (15.3 cm) round
50 cm (19.6 in.)
74.5 cm (29.3 in.)
6 cm
(2.3 in.)
54.8 cm
(21.5 in.)
32.4 cm
(12.75 in.)
28.3 cm
(11.1 in.)
99.8 cm
(39.3 in.)
Range Hood Dimensions and Specications
AN-1159
— 9 —
Range Hood Dimensions and Specications
AN-1176
Specications
Body Design Stainless Steel
Power Rating 120V/60Hz(cETLusCertied)
Total Input Power 88 W (85 W + 2 × 1.5 W)
Motor Input Power 85 W
Amperage 0.8 A
Speed Control Levels 3 Speeds
Interference Protection Radio Frequency Interference Protected
Motors Single Motor
Control Mechanical control panel
Filtration Aluminium lter
Illumination 2 × 1.5 W LED
Fan Type Single squirrel cage
VentingSize Top, 6 inches (15.3 cm) round
47 cm
(18.5 in.)
74.5 cm (29.3 in.)
6.6 cm
(2.6 in.)
54.5 - 99.5 cm
(21.4 - 39.1 in.)
28.3 cm
(11.1 in.)
32.4 cm
(12.75 in.)
56.2 cm (22.1 in.)
— 10 —
50 cm (19.6 in.)
74.5 cm (29.3 in.)
6 cm
(2.3 in.)
54.8 cm
(21.5 in.)
32.4 cm
(12.75 in.)
28.3 cm
(11.1 in.)
99.8 cm
(39.3 in.)
Specications
Body Design Stainless Steel
Power Rating 120V/60Hz(cETLusCertied)
Total Input Power 383 W (380 W + 2 × 1.5 W)
Motor Input Power 380 W
Amperage 3.2 A
Speed Control Levels 3 Speeds
Interference Protection Radio Frequency Interference Protected
Motors Single Motor
Control Electronic control panel
Filtration Decorative lter
Illumination 2 × 1.5 W LED
Fan Type Single chamber quiet
VentingSize Top, 6 inches (15.3 cm) round
Range Hood Dimensions and Specications
AN-1123
— 11 —
Range Hood Dimensions and Specications
AN-1533 / AN-1534
Specications
Body Design Stainless Steel / White
Power Rating 120V/60Hz(cETLusCertied)
Total Input Power 193 W (190 W + 2 × 1.5 W)
Motor Input Power 190 W
Amperage 1.7 A
Speed Control Levels 3 Speeds
Interference Protection Radio Frequency Interference Protected
Motors Single Motor
Control Mechanical control panel
Filtration Aluminium lter
Illumination 2 × 1.5 W LED
Fan Type Single chamber quiet
VentingSize Top, 6 inches (15.3 cm) round
48 cm (18.9 in.)
59.5 cm (23.4 in.)
3 cm
(1.1 in.)
39 - 74 cm
(15.3 - 29.1 in.)
25 cm
(9.8 in.)
20.9 cm
(8.2 in.)
17.2 cm
(6.75 in.)
— 12 —
Range Hood Dimensions and Specications
AN-1800 / AN-1802
Specications
Body Design White / Stainless Steel
Power Rating 120V/60Hz(cETLusCertied)
Total Input Power 82 W (80 W + 1 × 2 W)
Motor Input Power 80 W
Amperage 0.7 A
Speed Control Levels 3 Speeds
Interference Protection Radio Frequency Interference Protected
Motors Single Motor
Control Mechanical control panel
Filtration Aluminium lter
Illumination 1 × 2 W LED
Fan Type Single chamber quiet
VentingSize Top or rear, 10 in. × 3 1/4 in. (25.4 cm x 8.3
cm) Rectangular
10 cm
(3.9 in.)
14.8 cm
(5.8 in.)
8 cm
(3.1 in.)
48 cm (18.9 in.)
59.5 cm (23.4 in.)
33.6 cm (13.2 in.)
25.5 cm (10 in.)
54.9 cm (21.6 in.)
54.9 cm (21.6 in.)
15.3 cm
(6 in.)
6.1 cm
(2.4 in.)
10 cm
(3.9 in.)
14.8 cm
(5.8 in.)
8 cm
(3.1 in.)
48 cm (18.9 in.)
59.5 cm (23.4 in.)
33.6 cm (13.2 in.)
25.5 cm (10 in.)
54.9 cm (21.6 in.)
54.9 cm (21.6 in.)
15.3 cm
(6 in.)
6.1 cm
(2.4 in.)
24.5 cm (9.6 in.)
7.5 cm
(3 in.)
— 13 —
Mounting Brackets for Wall Hoods
Upper Chimney Bracket
Lower Chimney Bracket
Mounting Bracket Hook (all models)
20.4 cm (8 in.)
0.8 cm
(0.3 in.)
16.51 cm (6.5 in.)
18.01 cm (7.1 in.)
0.5 cm
(0.2 in.)
2 cm (0.75 in.)
2.5 cm
(1 in.)
19.35 cm (7.6 in.)
18.77 cm (7.4 in.)
15 cm (5.9 in.)
16.5 cm (6.5 in.)
0.6 cm
(0.2 in.)
0.5 cm
(0.2 in.)
2 cm (0.75 in.)
2.5 cm
(1 in.)
175 mm (6.8 in.)
40 mm
(1.5 in.)
6 mm
(0.2 in.)
8 mm
(0.3 in.)
28 mm (1.1 in.)
19 mm
(0.75 in.)
160 mm (6.3 in.)
199 mm (7.8 in.)
20 mm (0.75 in.)
27.9 cm (11 in.)
31.8 cm (12.5 in.)
2.5 cm
(1 in.)
2.5 cm
(1 in.)
26.2 cm (10.3 in.)
30 cm (11.8 in.)
AN-1158 / AN-1533 / AN-1534
— 14 —
Mounting Brackets for Wall Hoods
Upper Chimney Bracket
Lower Chimney Bracket
Mounting Bracket Hook (all models)
20.4 cm (8 in.)
0.8 cm
(0.3 in.)
16.51 cm (6.5 in.)
18.01 cm (7.1 in.)
0.5 cm
(0.2 in.)
2 cm (0.75 in.)
2.5 cm
(1 in.)
19.35 cm (7.6 in.)
18.77 cm (7.4 in.)
15 cm (5.9 in.)
16.5 cm (6.5 in.)
0.6 cm
(0.2 in.)
0.5 cm
(0.2 in.)
2 cm (0.75 in.)
2.5 cm
(1 in.)
175 mm (6.8 in.)
40 mm
(1.5 in.)
6 mm
(0.2 in.)
8 mm
(0.3 in.)
28 mm (1.1 in.)
19 mm
(0.75 in.)
160 mm (6.3 in.)
199 mm (7.8 in.)
20 mm (0.75 in.)
27.9 cm (11 in.)
31.8 cm (12.5 in.)
2.5 cm
(1 in.)
2.5 cm
(1 in.)
26.2 cm (10.3 in.)
30 cm (11.8 in.)
AN-1159 / AN-1176 / AN-1123
20.4 cm (8 in.)
0.8 cm
(0.3 in.)
16.51 cm (6.5 in.)
18.01 cm (7.1 in.)
0.5 cm
(0.2 in.)
2 cm (0.75 in.)
2.5 cm
(1 in.)
19.35 cm (7.6 in.)
18.77 cm (7.4 in.)
15 cm (5.9 in.)
16.5 cm (6.5 in.)
0.6 cm
(0.2 in.)
0.5 cm
(0.2 in.)
2 cm (0.75 in.)
2.5 cm
(1 in.)
175 mm (6.8 in.)
40 mm
(1.5 in.)
6 mm
(0.2 in.)
8 mm
(0.3 in.)
28 mm (1.1 in.)
19 mm
(0.75 in.)
160 mm (6.3 in.)
199 mm (7.8 in.)
20 mm (0.75 in.)
27.9 cm (11 in.)
31.8 cm (12.5 in.)
2.5 cm
(1 in.)
2.5 cm
(1 in.)
26.2 cm (10.3 in.)
30 cm (11.8 in.)
— 15 —
STEP 1
Read the Safety Instructions
• It is very important to read the safety instructions on pages 4 and 5.
IMPORTANT: It is the installer’s responsibility to comply with installation clearances.
STEP 2
Unpack Range Hood and Prepare Tools
• Carefully unpack the range hood and parts. Make sure all parts are included as shown on page 6.
• DO NOT remove the protective lm covering the appliance until the installation is fully completed.
• Consult a qualied and trained installer or check local codes for makeup air requirement, if any.
STEP 3
Plan Desired Location
• Plan a desirable location that ts all requirements in the Safety and Installation sections of this manual. Plan where
and how the ductwork will be installed.
• A straight or short duct run will allow the unit to perform most efciently. Long duct runs, elbows and transitions
will reduce the performance of the unit. Each elbow is equivalent to 5 to 10 feet (1.5 m to 3 m) of straight run.
Propersizeductworkshouldbe6in.(15.3cm)indiameter.
• To reach a 9 ft (2.7 m) ceiling make sure hood is installed 30 inches (
76.2 cm)
from cooking surface. If you
have a ceiling greater than 9 ft (2.7 m), please visit anconahome.com to order a chimney extension.
• If ductwork is already installed: ensure ductwork is free from debris and measures
6 in. (15.3 cm)
(1 in. (2.5 cm)
reducers may be used but more than 1 in. (2.5 cm) will overwork the motor and the unit will not function properly).
STEP 4
Test Unit Functions
• Plug the unit in and test all of the functions before installing.
• Placetherangehoodonaat,stablesurface.Connecttherangehoodtoadesignatedstandardoutlet(120-Volt,60Hz,
AC only) and turn on the range hood. Verify all operations of the range hood by referring to
Range Hood Operations.
• Turn power On in control panel.
• Check all lights and fan operations.
WARNINGS:
• PleasemakesuretoreadALLsafetyinstructionsonpages4and5.
• Usetwoormorepeopletomoveandinstallrangehood.
• Failuretofollowtheseinstructionscanresultinseriousinjury.
Installation
— 16 —
Installation
STEP 5
Venting Installation Guidelines
• The following steps are for exterior ventilation.
Height and Clearance
IMPORTANT:
•
Vent system must terminate to the outside (roof or side wall).
• DONOT
terminate the vent system in an attic or other
enclosed area.
• DONOTuse4in.(10.2cm)laundry-typewallcaps.
• Usemetal/aluminumventonly.Arigidmetal/aluminum
vent is recommended.
• DONOTuseaplasticvent.
• Alwayskeeptheductcleantoensureproperairflow.
• Calculatethefollowingfiguresbeforeinstallation:
1. Distance from the floor to the ceiling
2. Distance between the floor and the countertop/stove
3.
A distance of 24 in. to 30 in. (61 cm to 76.2 cm) is
recommended between stove top and the bottom of
range hood. 30 in. (76.2 cm) minimum is required for
gas stove tops.
4. Height of hood and duct cover.
For the most efficient and quiet operation:
• Itisrecommendedthattherangehoodbevented
vertically through the roof through 6 in. (15.3 cm) round,
or through the roof or wall 3-1/4 x 10 in. (8.3 cm x 25.4
cm) rectangular duct or bigger metal/aluminum vent
work.
• Thesizeoftheventshouldbeuniform.
• Usenomorethanthree90°elbows.
•
Make sure there is a minimum of 24 in. (61 cm) of
straight vent between the elbows if more than one
elbow is used.
• DONOTinstalltwoelbowstogether.
•
The length of vent system and number of elbows should be
kept to a minimum to provide efficient performance.
• Theventsystemmusthaveadamper.Ifrooforwall
cap has a damper, you may remove damper flaps from
damper to increase air flow.
• Onlyoneflangeisneededintheairductsystem,either
on top of the motor or outside.
•
Use silver tape or duct tape to seal all joints in the
vent system.
•
Use caulking to seal exterior wall or roof opening
around the cap.
— 17 —
Installation
• This range hood is factory set for
venting through the roof or wall.
• Vent work can terminate either
through the roof or wall. To vent
throughawall,a90°elbowis
needed.
IMPORTANT:
• NEVER exhaust air or terminate
duct work into spaces between
walls, crawl spaces, ceiling, attics
or garages. All exhaust must be
ducted to the outside.
• Use metal/aluminum duct work only.
• Fasten all connections with sheet
metal screws and tape all joints with
certied Silver Tape or Duct Tape.
• Use caulking to seal exterior wall or
roof opening around the cap.
TOP VENTING
ROOF EXHAUST
TOP VENTING
WALL EXHAUST
IMPORTANT:
•
A minimum of 6 in. (15.3 cm) round or 3-1/4 x 10 in. (8.3
cm x 25.4 cm) rectangular duct must be used to maintain
maximum airflow efficiency.
• Alwaysuserigidtypemetal/aluminumductsifavailableto
maximizeairflowwhenconnectingtoprovidedduct.
• PleaseuseDuctRunCalculationbelowtocompute
total available duct run when using elbows, transitions
and caps.
• ALWAYS,whenpossible,reducethenumberor
transitions and turns. If long duct run is required,
increaseductsizefrom6in.(15.3cm)to7in.(17.7
cm) or 8 in. (20.3 cm). If a reducer is used, install a
long reducer instead of a pancake reducer. Reducing
ductsizewillrestrictairflowanddecreaseairflow,thus
reduceductsizeasfarawayfromopeningaspossible.
• Ifturnsortransitionsarerequired,installasfaraway
from opening and as far apart, between two (2), as
possible.
• Minimummountheightbetweenstovetoptohood
bottom should be no less than 24-inch (61 cm) for
electric cook tops and minimum of 30-inch (76.2 cm)
for gas stove tops and no higher than 30-inch (76.2 cm)
for electric cook tops.
• Itisimportanttoinstallthehoodatthepropermounting
height. Hoods mounted too low could result in heat
damageandfirehazard;whilehoodsmountedtoohigh
may be hard to reach and will lose its performance and
efficiency.
• Ifavailable,alsorefertostovetopmanufacturer’s
height clearance requirements and recommended
hood mounting height above range.
Duct Run
Calculation
example:
One roof cap, two
90º elbows, and
one 45º elbow use.
0ft + 9ft + 9ft + 5ft
= 23ft used.
Deduct 23ft from
30ft, 7ft maximum
available for
straight duct run.
TOP VENTING
ROOF EXHAUST
TOP VENTING
WALL EXHAUST
REAR VENTING
CABINET HOOD VENTING
WALL HOOD VENTING
— 18 —
Installation
STEP 6
Preparations
NOTE: To avoid damage to your hood, prevent debris from entering the vent opening.
• Determine and mark the center line on the ceiling or wall where the range hood will be installed.
• Make sure there is proper clearance within the ceiling or wall for exhaust vent.
• Duetotheweightandsizeofthisunit,pleasemakesurethatthesupportsystemorframeworkbeingusedisstableand
secure in the ceiling or wall.
• Put a thick, protective covering over counter top, cooktop or range to protect from damage or dirt.
• Removeanyhazardousobjectsaroundtheareawheninstalling.
CAUTION
If moving the cooking range is necessary to install the hood, turn OFF the power on an electric range at the main
electrical box. SHUT OFF THE GAS BEFORE MOVING A GAS RANGE
STEP 7A (wall hoods only)
Installing the Hood Mounting Bracket
• Use a pencil to mark on the wall the desired placement of the range hood mounting screws.
• The range hood will be installed on top of this bracket (See Figure #1).
• Using references in Height & Clearance on Page 16 and Measurements and Diagrams on Pages 7 to 14, drill three holes
that will be used to x the lower mounting bracket.
STEP 8A (wall hoods only)
Installing the Upper Chimney Bracket
• Drilltwoholesaccordingtothesizeoftheuppermountingbracket.Theuppermountingbracketshouldbepositioned
ushwiththetopoftheoutsidechimney(SeeFigure#1-1or#1-2)
• Screw upper and hood mounting brackets in tightly.
Fig. #1-2
Flush to
the ceiling
• If performing wall installation, please follow Steps A
• If performing under cabinet installation, please follow Steps B
Fig. #1-1
165
88
88
279
88
88
AN-1158 / AN-1533 / AN-1534 AN-1159 / AN-1176 / AN-1123
165
88
88
279
88
88
— 19 —
Installation
STEP 10A (wall hoods only)
Mount Range Hood onto Wall
• Hang the range hood on the hooks of the hood mounting bracket.
(See Figure #4)
• Screw the range hood to the wall.
CAUTION - Make certain the range hood is secure before
releasing!
STEP 9A (wall hoods only)
Venting
• Fixthedamperaponthetopventofhood.
• If ventilation system is equipped with an external air duct with a different
diameter, apply a reduction tting. However, for maximum performance
and safety, a 6 in. round ducting is recommended.
Fig. #3
Fig. #4
STEP 11A (wall hoods only)
Connect Ductwork
• Attach ductwork to duct. Secure the ductwork with duct tape to make sure joints are secure and air- tight.
• Donotinstalltheducttapetootightlyasthismaypreventthedamperapsfromopeningwhichwilloverworkthemotor
and cause improper functioning of the unit.
• Fasten all connections with sheet metal screws and tape all joints with certied aluminum or foil tape. Use caulking to
seal exterior wall or roof opening around the cap.
STEP 12A (wall hoods only)
Connect to AC
• ConnectACplugintoagroundedACoutlethaving120V,60Hz.Placetheoutletatamaximumdistanceof33-1/2in.
(851 mm) from where the cord exits on the hood.
• SEE IMPORTANT INSTRUCTIONS ON NEXT PAGE.
3-Pronged Plug
Ground Plug
3-Prong Receptacle
• Optional step: For extra support, drill 2 additional holes aligned to
hood’s pre-drilled holes, and to mount the hood onto the wall. (See
Figure #2)
Fig. #2
— 20 —
IMPORTANT:
• Observeallgoverningcodesandordinances.
• It is the customer’s responsibility to contact a qualified electrical installer.
• Ifcodespermitandaseparategroundwireisused,itisrecommendedthataqualifiedelectriciandeterminethat
thegroundpathisadequate.A120-Volt,60Hz,AC-only,fusedelectricalsupplyisrequiredonaseparate15-amp
circuit, fused on both sides of the line.
• DONOTgroundtoagaspipe.
• Checkwithaqualifiedelectricianifyouarenotsurethattherangehoodisproperlygrounded.
• DONOThaveafuseintheneutralorgroundcircuit.
IMPORTANT: Save this Installation Guide for electrical inspector’s use.
GROUNDING INSTRUCTIONS:
• Thisappliancemustbegrounded.Intheeventofanelectricalshort-circuit,groundingreducestheriskofelectric
shock by providing an escape wire for the electric current.
• Thisapplianceisequippedwithacordhavingagroundingwirewithagroundingplug.Theplugmustbeplugged
into an outlet that is properly installed and grounded.
WARNING: Improper grounding can result in a risk of electric shock.
• Consultaqualifiedelectricianifthegroundinginstructionsarenotcompletelyunderstood,orifdoubtexistsasto
whether the appliance is properly grounded. DO NOT use an extension cord. If the power supply cord is too short,
have a qualified electrician install an outlet near the appliance.
Installation
STEP 13A (wall hoods only)
Install Chimney
• Place chimney on top of the main housing
• Remove the protective coating from the upper chimney. Carefully slide the upper chimney down into the lower chimney.
Make sure upper chimney is moving freely.
• Hook lower chimney bracket to lower chimney, then screws the lower chimney bracket on wall. (See Figure #5)
• Screw the upper chimney to the upper mounting bracket. (See Figure #6)
Fig. #6Fig. #5
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Ancona AN-1800 User manual

Ancona
Brand
Ancona
Model
AN-1800
Category
Cooker hoods
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents