Body-Solid TF6iHRC Owner's manual

Brand
Body-Solid
Model
TF6iHRC
Type
Owner's manual
ENDURANCE TF6i
VERSION 0410
PAGE 1
Qty.
40
20
60 80
100
140
160
120
ENDURANCE TF6i HARDWARE ILLUSTRATION SHEET
A1.M10X95 Round Inner Hex Screw--------[4pcs]
A2.M10X120 Round Inner Hex Screw--------[2pcs]
A3.M10X50 Round Inner Hex Screw----------[2pcs]
A4.M10X15 Round Inner Hex Screw----------[6pcs]
A5.M4X15 Round Cross Screw-----------------[2pcs]
C1.M10 (I.D)Washer------------------------------[8pcs]
C2.M4 (I.D)Washer-------------------------------[2pcs]
A1
A2
A3
A4
C1
C2
A5
ENDURANCE TF6i PARTS ILLUSTRATION SHEET
A[1PCS]
B[1PCS]
J[1PCS]
C[1PCS]
D[1PCS]
E[2PCS]
F[1PCS]
I[1PCS]
H[1PCS]
G[1PCS]
PAGE 2
B
A4
A4
A3
E
A3
E
A4
A4
ENDURANCE TF6i
PAGE 3
Do not tighten the bolts down
completely during first assembly.
After the completion of step 3,then you
may tighten the bolts completely.
Do not tighten the bolts down
completely during first assembly.
After the completion of step 3,then you
may tighten the bolts completely.
ENDURANCE TF6i
PAGE 4
PAGE 3
A4
C1
A2
C1
A5
C2
A2
C1
G
H
A1
C1
J
A1
C1
Assemble Procedurse:
1.F
2.G
3.H
4.J
5.PAGE 3
6.OTHERS
F
ENDURANCE TF6i
After assembly and before turning
power on position the rear roller using
the ' T ' wrench ( refer to the drawing if needed ) .
If belt is too far to the left side
1) turn the left roller bolt 1/4 turn clockwise(tighten)
2) turn the right roller 1/4 turn counterclockwise(loosen)
If belt is too far to the right side
1) turn the right roller bolt 1/4 turn clockwise(tighten)
2) turn the left roller bolt 1/4 turn counterclockwise(loosen)
make 3 turns
PAGE 5
TENSIONING THE BELT
Running Belt
If when you plant your foot on the belt , you can feel a sliping
sensation then the belt has been stretched and is slipping over the roller.
This is normal and common adjustment on a new treadmill.
To eliminate this slipping , tighten both sides of the rear roller by wing a Allen wrench
turn 1/4 of a TURN as shown above .Try the treadmill again to check for slipping.
Repeat if necessary . but NEVER TURN the roller bolt more than 1/4 turn at a time.
CAUTION:OVER TIGHTENING OF THE ROLLER WILL SEVERELY SHORTEN
THE LIFE OF THE BELT AND MAY CAUSE FURTHER DAMAGE TO OTHER
COMPONENTS.
Drive Belt
If you have tightened the running belt and are still experiencing
a slipping sensation , call your Steel Flex Dealer . Tightening
of the drive belt should only be performed by an authorized
dealer.
ENDURANCE TF6i
PAGE 6
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Body-Solid TF6iHRC Owner's manual

Brand
Body-Solid
Model
TF6iHRC
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents