Page is loading ...
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 357497 12/05/13
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Library with Doors
Palladia Collection | Model 412019
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
The stories of your life.
Table of Contents Assembly Tools Required
2-3
4
5-22
23-25
26-28
29-30
31
Part Identifi cation
Hardware Identifi cation
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
412019 www.sauder.com/servicesPage 2
Part Identifi cation
å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identifi cation to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E SHELF (1)
F BACK (1)
G DOOR (2)
H ADJUSTABLE SHELF (2)
I LOWER ADJUSTABLE SHELF (1)
J SKIRT (1)
K BACK SKIRT (1)
L END MOLDING (2)
M VERTICAL MOLDING (2)
N TOP MOLDING (1)
O SHELF MOLDING (1)
P HORIZONTAL MOLDING (1)
Q ADJUSTABLE SHELF MOLDING (2)
R BOTTOM MOLDING (1)
S VALANCE (1)
T PLINTH (4)
U HALF DISK (4)
Straight Edge Screwdriver
Part Identifi cation
412019www.sauder.com/services
Page 3
A
B
C
D
E
F
G
G
H
H
I
J
K
L
L
M
M
N
O
P
Q
Q
S
T
T
T
U
T
U
U
U
R
Hardware Identifi cation
å Screws are shown actual size. You may receive extra hardware with your unit.
412019 www.sauder.com/servicesPage 4
BLACK 1-1/8" MACHINE SCREW - 2
II
SAFETY BRACKET - 1
Z
METAL
BRACKET - 2
X
TIE PLATE - 6
Y
BLACK 9/16" LARGE HEAD SCREW - 29
KK
ANGLE BRACKET - 6
W
SILVER 1-1/8" FLAT HEAD SCREW - 12
HH
TWIST-LOCK® FASTENER - 20
V
BROWN 1" FLAT HEAD SCREW - 8
JJ
RUBBER SLEEVE - 12
CC
METAL PIN - 12
BB
BLACK 1/2" FLAT HEAD SCREW - 8
LL
AA
HINGE - 4
DOOR STOP - 2
DD
KNOB - 2
EE
NAIL - 62
MM
SCREW COVER - 3
FF
BLACK 1-7/8" PAN HEAD SCREW - 1
GG
Step 1
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å
Assemble your unit on a carpeted fl oor or on the empty
carton to avoid scratching your unit or the fl oor.
å
To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (V) into the large holes in the ENDS (A and B),
BOTTOM (D), and SHELF (E).
412019www.sauder.com/services
Page 5
V
V
V
V
A
B
V
(20 used)
Do not tighten the TWIST-LOCK® FASTENERS in this step.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1631
to watch a video on how to assemble your unit.
Step 2
å
Fasten two PLINTHS (T) to the ENDS (A and B). Tighten
two TWIST-LOCK® FASTENERS.
412019 www.sauder.com/servicesPage 6
How to use the SAUDER TWIST-LOCK
®
FASTENER
1. Insert the dowel end of the FASTENER into the hole
of the adjoining part.
NOTE: The dowel end of the FASTENER must remain
fully inserted in the hole of the adjoining part while
locking the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as
tight as possible.
Dowel end
Curved edge
Curved edge
T
T
A
B
Dowel end
Use the lower large
hole in the PLINTH.
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
å
Fasten six ANGLE BRACKETS (W) to the END MOLDINGS (L).
Use six BLACK 9/16" LARGE HEAD SCREWS (KK).
å
NOTE: Be sure the edges of the ANGLE BRACKETS are even
with the edges of the MOLDINGS.
Step 3
412019www.sauder.com/services
Page 7
W
W
L
L
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
KK
Step 4
å
Fasten the END MOLDINGS (L) to the ENDS (A and B).
Use six BLACK 9/16" LARGE HEAD SCREWS (KK).
412019 www.sauder.com/servicesPage 8
L
L
A
B
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
KK
These edges
should be even.
These edges
should be even.
å
Fasten two HALF DISKS (U) to a VERTICAL MOLDING (M).
Use two BROWN 1" FLAT HEAD SCREWS (JJ).
å
Repeat this step for the remaining HALF DISKS and
VERTICAL MOLDING.
Step 5
412019www.sauder.com/services
Page 9
BROWN 1" FLAT HEAD SCREW
(4 used in this step)
JJ
The large hole should be facing away
from the VERTICAL MOLDING (M).
The large hole should
be facing away from the
VERTICAL MOLDING (M).
M
U
U
Flat edge down
Step 6
å
Fasten the VERTICAL MOLDINGS (M) to the END MOLDINGS (L).
Use six SILVER 1-1/8" FLAT HEAD SCREWS (HH).
å
NOTE: Be sure the HALF DISK is against the PLINTH (T) before
tightening any screw. The screws should tighten into the groove of
the VERTICAL MOLDING. Do not overtighten.
412019 www.sauder.com/servicesPage 10
SILVER 1-1/8" FLAT HEAD SCREW
(6 used in this step)
HH
L
L
M
M
T
T
å
Fasten the HORIZONTAL MOLDING (P) to the
SHELF MOLDING (O). Use three SILVER 1-1/8" FLAT
HEAD SCREWS (HH).
å
Fasten the SHELF MOLDING (O) to the SHELF (E).
Tighten two TWIST-LOCK® FASTENERS.
Step 7
412019www.sauder.com/services
Page 11
Surface with
TWIST-LOCK®
FASTENERS
O
P
E
Unfi nished
surface
SILVER 1-1/8" FLAT HEAD SCREW
(3 used in this step)
HH
Curved edge
Rounded edge
Step 8
å
Fasten the TOP MOLDING (N) to the TOP (C) as shown in the upper
diagram below. Use three SILVER 1-1/8" FLAT HEAD SCREWS (HH).
å
Fasten the LEFT END (B) to the TOP (C). Tighten two
TWIST-LOCK® FASTENERS.
å
Fasten the BOTTOM (D), SHELF (E), and PLINTH (T) to the LEFT
END (B). Tighten fi ve TWIST-LOCK® FASTENERS.
å
Fasten the BOTTOM MOLDING (R) to the BOTTOM (D). Tighten
two TWIST-LOCK® FASTENERS.
412019 www.sauder.com/servicesPage 12
C
N
Surface with
TWIST-LOCK®
FASTENERS
Surface with
TWIST-LOCK®
FASTENERS
C
E
D
R
B
T
Finished
SILVER 1-1/8" FLAT HEAD SCREW
(3 used in this step)
HH
Curved edge
These surfaces
should be even.
Curved edge
Curved edge
Rounded edge
Rounded edge
Unfi nished edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
N
Surface with TWIST-LOCK® FASTENERS
å
Fasten the remaining PLINTH (T) to the RIGHT END (A).
Tighten the TWIST-LOCK® FASTENER.
å
Fasten the RIGHT END (A) to the TOP (C), SHELF (E), and
BOTTOM (D). Tighten six TWIST-LOCK® FASTENERS.
Step 9
412019www.sauder.com/services
Page 13
C
E
D
T
A
These surfaces
should be even.
Curved edge
Surface without TWIST-LOCK® FASTENERS
Step 10
å
Fasten the BACK SKIRT (K) to the SKIRT (J). Use four
BROWN 1" FLAT HEAD SCREWS (JJ).
å
Fasten two TIE PLATES (Y) to the BACK SKIRT (K) and
four TIE PLATES (Y) to the VALANCE (S). Use six BLACK
9/16" LARGE HEAD SCREWS (KK).
412019 www.sauder.com/servicesPage 14
K
J
Unfi nished surface
Surface
with
holes
Y
S
BLACK 9/16" LARGE HEAD SCREW
(6 used for the TIE PLATES)
KK
(6 used)
BROWN 1" FLAT HEAD SCREW
(4 used for the SKIRTS)
JJ
å
Carefully turn your unit over onto its front edges.
å
Fasten the BACK SKIRT (K) to the lower PLINTHS (T). Use two
BLACK 9/16" LARGE HEAD SCREWS (KK).
å
Fasten the METAL BRACKETS (X) to the BOTTOM (D) and BACK
SKIRT (K). Use four BLACK 9/16" LARGE HEAD SCREWS (KK).
å
Fasten the VALANCE (S) to the PLINTHS (T). Use four BLACK
9/16" LARGE HEAD SCREWS (KK).
Step 11
412019www.sauder.com/services
Page 15
BLACK 9/16" LARGE HEAD SCREW
(10 used in this step)
KK
X
S
K
T
T
T
T
D
Rounded edge
Step 12
å
Unfold the BACK (F) and lay it over your unit.
å
Make equal margins along all four edges of the BACK (F). Push
on opposite corners of your unit if needed to make it "square".
å
Fasten the BACK (F) to your unit using the NAILS (MM).
å
NOTE: Be sure to tap NAILS into the holes that line up over
the SHELF (E).
å
NOTE: Perforations have been provided for access through the
BACK. Carefully cut out the holes needed.
412019 www.sauder.com/servicesPage 16
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
These holes must line
up over the SHELF (E).
F
NAIL
(62 used in this step)
MM
å
Fasten the HINGES (AA) to the DOORS (G). Use eight
BLACK 1/2" FLAT HEAD SCREWS (LL).
Step 13
412019www.sauder.com/services
Page 17
AA
AA
G
G
BLACK 1/2” FLAT HEAD SCREW
(8 used in this step)
LL
Step 14
å
Carefully stand your unit upright.
å
NOTE: You may need to loosen the mounting and adjusting screws to
slide the hinge part way out of the slot before fastening it to the END.
Retighten the screw before you mount the HINGE to the END.
å
Fasten a DOOR (G) to the LEFT END (B). Use the screws in the
HINGES. See the next step for adjustments.
å
Fasten a KNOB (EE) to the DOOR (G). Use a BLACK 1-1/8"
MACHINE SCREW (II).
å
Repeat this step for the other door.
412019 www.sauder.com/servicesPage 18
G
EE
Mounting screw (depth)
Adjusting screw (horizontal)
B
BLACK 1-1/8" MACHINE SCREW
(2 used in this step)
II
å
Refer to the enlarged diagram to identify the parts on the HINGES.
å
The DOORS may need some adjustments. Follow the text below to make needed adjustments.
å
DOOR ADJUSTMENTS:
å
To adjust the DOORS from side to side (horizontal), turn the adjusting screw in or out.
å
To adjust the DOORS up and down (vertical), loosen both vertical adjustment screws. Move the DOORS up or down
to the desired location. Tighten the screws after making adjustments.
å
To adjust the DOORS in or out (depth), loosen the mounting screw one
turn and move the DOORS in or out, as needed. Tighten the
mounting screw after making adjustments.
Step 15
412019www.sauder.com/services
Page 19
Mounting screw (depth)
(vertical adjustment)
Adjusting screw (horizontal)
Step 16
å
Push two DOOR STOPS (DD) into the holes in the LOWER
ADJUSTABLE SHELF (I).
å
Slide the ADJUSTABLE SHELF MOLDING (Q) onto the
notched edge of the SHELF (H).
å
*U.S. Patent No. 5,499,886
412019 www.sauder.com/servicesPage 20
I
H
Q
DD
These edges
should be even.
Notched edge
/