TRUSTECH GD9315BCW-4JA User guide

Brand
TRUSTECH
Model
GD9315BCW-4JA
Category
Space heaters
Type
User guide
Electric Space Heater
MODEL: GD9315BCW-4JA
Thank you for choosing Trustech Space Heater!
This user manual will provide you with valuable information necessary for the proper care and
maintenance of your new product. Please take a few moments to thoroughly read it and start enjoying
your warm winter!
Always here to help you
For any questions or help, please email us: trustech@afterservice.vip
2
Warning:Please read the user manual carefully before using the unit and save it for future reference.
Thank you for choosing the products of TRUSTECH. This user manual will provide you with valuable
information necessary for the proper care and maintenance of your new product. Please take a few
moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of
your new heater.
When using electrical appliances, basic precautions should always be followed to reduce the
risk of fire, electric shock, injury to persons, and hyperthermia, including the following:
IMPORTANT INSTRUCTIONS
When using the unit, basic safety precautions should always be followed to reduce the risk of fire,
electric shock, and injury to persons.
1.Please read All the instructions before using this unit
2. Be aware of the risk of electric shock. DO NOT open or try to repair the heater by yourself.
3. This heater may get hot when it is in use. To avoid any harm,DO NOT touch hot surfaces with your
bare skin. If necessary, use the handles when moving this heater.
4. Keep combustible materials, such as furniture, pillow, bedding, paper, clothes, and curtains at least
3ft from the front of the heater and keep them away from the sides, top, and rear part. DO NOT place
towels or other objects on the heater.
5. You must pay extreme attention if the heater is used when there are children or the disabled nearby.
Don't leave the heater operating and be unattended.
6. DO NOT operate the heater with a damaged cord or after any heater malfunctions, for example, it has
been dropped or damaged in any manner. Return the heater to the authorized service facility for
examination, electrical or mechanical adjustment, or repair.
7. The heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER
locate the heater where it may fall into a bathtub or other water container. To protect against electrical
hazards, DO NOT immerse it into water or other liquids.
8. DO NOT touch the control panel or plug it with a wet hand.
9. DO NOT place the cord under carpets. DO NOT cover the cord with rugs, or similar coverings. Place
the cord at the place where it will not be tripped over.
10. DO NOT insert or put any other objects to enter any ventilation or exhaust opening as this may cause
an electric shock or fire, or damage the heater.
11. To prevent a possible fire, DO NOT block the air intake or exhaust in any manner.
12. DO NOT use it on soft surfaces where may block its openings, like a bed.
3
13. There are hot and arcing or sparking parts inside a heater. DO NOT use it in areas where gasoline,
paint, explosive and/ or flammable liquids are used or stored. Keep the unit away from heated surfaces
and open flames.
14. Always plug the heater directly into a wall outlet. Never use it with an extension cord or relocate the
power tap (power outlet/ power strip).
15. To avoid a fire or shock hazard, plug the unit directly into a 120 V AC electrical outlet.
16. To disconnect the heater, turn controls to OFF, and then remove the plug from the power outlet. DO
NOT unplug it by pulling the cord violently.
17. Always unplug the unit before moving or cleaning it, and whenever the heater is not in use.
18. It can be used for household use only as described in this manual. It is not recommended to use it for
other functions, or it may cause a fire, electric shock, or injury to persons. And please use the original
attachments provided or sold by unauthorized dealers, or it may cause hazards.
19. Always use it on a dry, level surface. Use it on the floor only.
20. DO NOT use it outdoors.
21. To reduce the risk of fire or electric shock, DO NOT use the unit with any speed control device.
22. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will
void your warranty. There is not any user- serviceable part inside of the unit. If the unit needs to be
examined or repaired, please contact the qualified personnel for help.
23. Connect the unit to properly grounded outlets only.
24. Hyperthermia can result in death. Symptoms of hyperthermia include high body
temperature, headache, nausea, vomiting, tiredness, dizziness, fainting, and rapid pulse. If
you begin to experience symptoms related to hyperthermia, turn off the heater and seek
medical attention.
25. To avoid excessive room temperatures which can cause hyperthermia: DO NOT leave
product running unattended in a confined space around infants, or individuals with reduced
physical, sensory, or mental capabilities.
26. Save the user manual for future reference.
SPECIFICATION
Voltage Rating
120 V (60Hz)
Power Consumption
1500W
Unit Size
11.97 in. (W) ×10.79 in. (D) ×15.51 in. (H)
Unit Weight
13.89 lbs
4
SAFETY FEATURES
Tip-Over Safety Feature
The heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal switch
will automatically shut the heater off. Once the heater is restored to an upright position, the heater will
be reset. To continue the operation, turn on the heater by using the supplied remote control or pressing
the key on the control panel of the heater.
Overheat Safety Feature
The heater is equipped with an overheat safety feature. When the heater's internal components reach a
certain temperature that could cause overheat or possible fire, the heater will automatically shut off.
OVERHEAT SAFETY FEATURE
Warnings:
The voltage rating of the heater is 120 volts. It is a 3-pin grounded outlet as shown in A, and you can
plug the unit directly. An adapter as shown in C is available for connecting the 3-pin plug to a 2-prong
outlet. The ground lug extending from the adapter must be connected to the ground. The adapter
should not be used if you can use the unit with the 3-pin grounded outlet directly.
Do not neglect the safety purpose of the grounded plug. It is normal for the power cord to feel warm
when the unit is in use, however, a loose connection between the outlet and the plug may cause
overheating of the plug. If this occurs, try to insert the plug into a different outlet. Contact a qualified
electrician to inspect the original outlet in case of any hazards.
5
ITEMS IN THE BOX
1* Infrared Zone Heating System
1* Remote Control (It needs 2 AAA batteries, but not Included.)
1* User Manual
PRODUCT DIAGRAM
CONTROL PANEL
1. ON/OFF Button: To power the unit on and off.
2. Mode Button: To select the mode among the High, Low and Eco modes.
3.1 High Mode Indicator: It will light up when the high-heat mode is started.
3.2 Low Mode Indicator: It will light up when the low-heat mode is started.
3.3 Energy-saving Mode Indicator: It will light up when the energy-saving mode is started.
6
4. Timer Button: It is used to use the Timer mode and to set the time.
5. Temp-up Button: To increase the desired temperature.
6. Temp-down Button: To decrease the desired temperature.
7. Digital Display: It indicates the set room temperature or time.
8.1 Celsius Indicator: It will light up when the temperature is displayed in Celsius.
8.2 Fahrenheit Indicator: It will light up when the temperature is displayed in Fahrenheit.
9. Signal Receiving Window: It is for receiving a remote control signal.
REMOTE CONTROL
PREPARATION
Place the heater on a firm, level surface and plug it into a 120V 60Hz grounded power outlet. Turn on
the power switch in the rear part of the unit. Only operate the heater in the upright position. Insert 2
AAA batteries into the remote control before using the remote control. (The batteries are not included.)
℃/℉button: It is for alternating the temperature displayed
between Fahrenheit and Celsius.
ON/OFF button: to power the unit on/ off
Temp up button: to increase the desired temperature
Temp down button: to decrease the desired temperature
Timer button: It is used for setting the Timer and adjust the time value
Mode button：for mode selection
7
OPERATING INSTRUCTION
1. Get Started and Select the Working Mode
Tum the heater on by pressing the ON/OFF button
on the control panel or by pressing the Power
button on the supplied remote control.
Once the unit powers off, the heating element will
stop working at first. But the fan will continue
working for 3 minutes to dissipate the heat inside.
Select a heat Mode.
Press the Mode button to select the modes among
three heat modes.
The high mode consumes 1500W; while the
low mode uses 750W. ECO mode is an
Economic Energy-saving Function. When
the ECO mode is chosen, the heater will
manage itself from less to more heating
power (watts) in an attempt to maintain a
constant warmth of 68℉, (20℃).
8
2. Set the Desired Temperature
Adjust the desired temperature by pressing
the Up/ Down button on the control panel
or remote control.
The desired temperature options vary from
59 ℉to 86 ℉, or from 15 ℃to 30 ℃. Once the
desired temperature has been chosen, the
heater will remain on until the room
temperature increases to the temperature
on the digital display, The heater will cycle
on and off to maintain the desired temperature in
the room.
Press the ℃/ ℉ button to change the
dislayed temperature between Fahrenheit
and Celsius.
Long press the Mode button, you can
convert the temperature displayed between
Fahrenheit and Celsius.
The Fahrenheit indicator will light up when
the temperature is displayed in Fahrenheit.
The Celsius indicator will light up when the
temperature is displayed in Celsius.
9
3. Set the timer to power off
Note:
Setting the Timer to power off the unit will allow the heater to power off after a certain set time, and
can only be set while the heater is in the "On" position.
Turn the heater on. Press the Timer button
on the heater's control panel or remote
control.
The digital display changes from the
"temperature" to the "hours" option for the
timer. Continue to press the Timer button
to change the number of hours you would
like the heater to run before powering itself
off. The hour options for the timer are from
0 to 12 hours (in 1 hour increment).
The selected hour increments will flash for
a few seconds, then revert to the set
desired temperature. The Timer indicator
will remain on as long as the' Timer is set.
The heater will power off when the internal
heater clock counts down the hour
increments you set.
10
4. Set the timer to power ON
Note:
Setting the Timer to power on will allow the heater to power on after a certain set time, and can only be
set while the heater is in the "Off" position.
Turn the heater on. Press the Timer button
on the heater's control panel or remote
control.
The digital display shows the "hours" option
for the timer. Continue to press the Timer
button to change the number of hours you
would like the heater's internal clock to
count down before powering itself on. The
hour options for the timer are from 0 to 12
hours (in 1 hour increment).
The Timer indicator will remain on as long
as the Timer is set. The heater will power
itself on when the internal heater clock
counts down the hour increments you set.
11
5. Set the electronic lock
The Electronic Lock can prevent the heater from being accidentally operated by children. The locking
mechanism can be set in both the ON and OFF modes.
Press the Temp-up and Temp-down
buttons at the same time for 3 seconds.
The locking is launched when you hear a
beep. When locked, the functions of the
control panel and remote control will be
locked for use.
When you need to unlock it, press the
Temp-up and Temp-down buttons at the
same time for 3 seconds. After that, you will
hear a beep. The control panel and remote
control will become functional again.
12
MAINTENANCE
1. Turn off the power switch in the rear part of the unit.
2. Unplug the unit and cool it completely.
3. To keep the heater clean, the outer shell should be cleaned with a soft, damp cloth. You may use a
mild detergent if necessary. After cleaning, dry the unit with a soft cloth. DO NOT let the liquid enter the
heater.
4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the
heater. This may cause damage or deterioration to the surface of the heater.
5. DO NOT immerse the heater into water.
6. Wait until the unit is completely dry before use.
7. The air filter needs cleaning after it is used for 3 months. Please take off the air filter with 2 steps as
shown in the drawing below. Flush and clean the air filter with water, and then dry it and reassemble it.
8. If you do not use the heater for a long time, please take out the batteries from the remote control (to
prevent corrosion) as shown below. Store the remote control in a safe place.
13
STORAGE
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the
original packaging to repack the unit.
TROUBLESHOOTING
If the heater cannot work normal, please check the following situations before seeking the repair advice.
1. Check if the power cord is plugged into an electrical outlet, if not, plug it in.
2. Check if the electricity to the main power switch (in the back) is working.
3. Check to see if the battery on the remote control is placed correctly and undamaged.
Note:
For the heater to function properly, the desired temperature on the heater must be set a few degrees
higher than the temperature in the room. If it seems that the unit cannot heat up normally, increase the
desired temperature on the heater to engage the heat elements.
WARRANTY
TRUSTECH warrants this product against defects in materials and/or workmanship under normal use for
a period of ONE (1) YEAR from the date of purchase by the original purchaser (“Warranty Period”). If a
defect arises and a valid claim is received within the Warranty Period, at its option, TRUSTECH will either
1) repair the defect at no charge, using new or refurbished replacement parts, or 2) replace the product
with a new product that is at least functionally equivalent to the original product, or provide a store
credit in the amount of the purchase price of the original product. A replacement product or part,
including a user-installable part installed in accordance with instructions provided by TRUSTECH,
assumes the remaining warranty of the original product. When a product or part is exchanged, any
replacement item becomes your property and the replaced item becomes TRUSTECH’s property. When
a store credit is given, the original product must be returned to TRUSTECH and becomes TRUSTECH’s
property. To obtain warranty service, e-mail TRUSTECH Limited Warranty Service at
trustech@afterservice.vip. Please be prepared to describe the product that needs services and the
nature of the problems.
This warranty does not apply to:
damage caused by failure to follow instructions relating to products’use or the installation of
components;
damage caused by accident, abuse, misuse, fire, floods, earthquake or other external causes;
damage caused by service performed by anyone who is not a representative of TRUSTECH;
accessories used in conjunction with a covered product
a product or part that has been modified to alter functionality or capability;
items intended to be periodically replaced by the purchaser during the normal life of the product
including, without limitation, batteries or light bulbs;
any product sold ‘as is’including, without limitation, floor demonstration models and refurbished items;
or
14
a product that is used commercially or for a commercial purpose.
CONTACT US
Thank you for choosing TRUSTECH product.
If there is a defect arises during one year, please feel free to contact us to get
your valid claim. To obtain warranty service, please your model and order of the product via:
 trustech@afterservice.vip
☎+1（855）620 5858
Our usual response time is within 12 hours!
15
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

TRUSTECH GD9315BCW-4JA User guide

Brand
TRUSTECH
Model
GD9315BCW-4JA
Category
Space heaters
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents