Lexing LX-LD-P200 Operating instructions

Brand
Lexing
Model
LX-LD-P200
Type
Operating instructions

Lexing LX-LD-P200 is a new type of energy-saving lighting lamp that utilizes infrared energy from the human body as its controlling source. It adopts a high sensitivity detector and integrated circuit, gathering automatism, convenience, safety, energy-saving, and practicality.

Here are some of its key features and possible use cases:

  • Automatic Lighting: The lamp automatically turns on when it detects motion within its 7-9m detection range and 180° detection angle. This makes it ideal for use in areas where you need hands-free lighting, such as hallways, entryways, and closets.
  • Energy Saving: The lamp only turns on when it detects motion, which helps to save energy compared to traditional lighting fixtures that are always on.

Lexing LX-LD-P200 is a new type of energy-saving lighting lamp that utilizes infrared energy from the human body as its controlling source. It adopts a high sensitivity detector and integrated circuit, gathering automatism, convenience, safety, energy-saving, and practicality.

Here are some of its key features and possible use cases:

  • Automatic Lighting: The lamp automatically turns on when it detects motion within its 7-9m detection range and 180° detection angle. This makes it ideal for use in areas where you need hands-free lighting, such as hallways, entryways, and closets.
  • Energy Saving: The lamp only turns on when it detects motion, which helps to save energy compared to traditional lighting fixtures that are always on.
LX-LD-P200 Sensor Night Lamp Instruction
The product is a new type of energy-saving lighting lamp; it adopts high sensitivity
detector and integrated circuit; it gathers automatism, convenience, safety, energy-saving
and practicality; it utilizes infrared energy from human body as its controlling source; at
night when one enters its detection field, the lamp will shine and after leaves it will go out
automatically.
Power source: 220-240V/AC
100-130V/AC
Power frequency: 50/60Hz
Light-control: <35LUX
Time setting: 60sec±10sec
Summary
You can set the lamp function according to your need:
-Slide switch to“I ”: the lamp will alwaysshine;
-Slide switch to“ O ”: the lamp won’t shine;
-Slide switch to“ AUTO”: in the ambient light below 5LUX to 35LUXwhen one enters the
detection rangethe lamp will light; after leaves the lamp goes out automatically
Rated load: 7W Max.
Detection range: 7~9m(22°C)
Detection angle: 180°
Working temperature: -10~+40°C
Working humidity: <93%RH
Function
Correct moving orientation
7-9m
<7m
<7m
Detection angle
180°
Switch function: ON/AUTO/OFF
Specifications Sensor information
>Slide switch to“ I ”, the lamp should always shine;
>Slide switch to“ O ”, the lamp should not shine;
>Slide switch to“ AUTO”:
1) Plug in the lamp;
2) After 30sec the lamp enters working state and the lamp goes out;
3) After the lamp goes out, make it sense, the lamp should light;
4) Under the condition that there is no continual induction, the lamp should go out within 60s±10s.
Test
Attentions
For you safety, you should take down the unit before you replacing the bulb;
The product shouldn’t be used in the zones the air temperature changes obviously: for example
air conditioning and air heating;
In front of the detection window there shouldbe no obstruction or moving object to effect its
detecting;
After the lamp light for some time, the lamp cover will be very hot, so here you should not touch
the lamp cover for your safety.
Problems and solutions
1. The lamp doesn’t work:
a.Please check if the power connection is ok;
b.Pleas check if the ambient working light accords with instruction.
2. The induction sensitivity is low:
a.Please check if in front of the detection window there is obstruction effecting the sensor to receive
signal;
b.Please check the temperature is too high;
c.Please check if the sense signal is in the detection range;
3. The sensor can not shut off the lamp automatically:
a)Check if in the detection range there is continual sense signal;
b)Check if the power accords with instruction required;
c)Check if the air temperature near the sensor lamp change obviously, for example air conditioning
or air heating, etc.
Warning!
● Please confirm with prefessional installation.
● Please cut off power supply before installation and removal operations.
● Make sure that you have cut off the power for safety purposes.
● Improper operation caused losses, the manufacturer does not undertake any responsibility.
We are committed to promoting the product quality and reliability, however, all the electronic
components have certain probabilities to become ineffective, which will cause some
troubles.When designing, we have paid attention to redundant designs and adopted safety
quota to avoid any troubles.
This instruction, without our permission, should not be copied for any other purposes.
  • Page 1 1
  • Page 2 2

Lexing LX-LD-P200 Operating instructions

Brand
Lexing
Model
LX-LD-P200
Type
Operating instructions

Lexing LX-LD-P200 is a new type of energy-saving lighting lamp that utilizes infrared energy from the human body as its controlling source. It adopts a high sensitivity detector and integrated circuit, gathering automatism, convenience, safety, energy-saving, and practicality.

Here are some of its key features and possible use cases:

  • Automatic Lighting: The lamp automatically turns on when it detects motion within its 7-9m detection range and 180° detection angle. This makes it ideal for use in areas where you need hands-free lighting, such as hallways, entryways, and closets.
  • Energy Saving: The lamp only turns on when it detects motion, which helps to save energy compared to traditional lighting fixtures that are always on.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents