Movincool CPD12 Installation guide

SERVICE MANUAL

CLIMATE PRO 18

Unit Serial Number Range: 0914XXXXH18 to Present

(From September 2014 to Present)

DocID: 00G00095E

SERIAL NUMBER LOCATION AND IDENTIFICATION

whole or in part, without the written permission of the publisher. DENSO

PRODUCTS AND SERVICES AMERICAS, INC. reserves the right to

make changes without prior notice. MovinCool®, Office Pro®,

and SpotCool® are registered trademarks of DENSO Corporation.

Nameplate Label Position

Nameplate Label

COOLING AMPS. WITH PUMP

COMPR. OUTPUT

REFRIGERANT/TOTAL CHARGE

DESIGN PRESSURE LO/HI

PART NO./WEIGHT

SERIAL NO.

Month Model

Sequential

Number

Year

Table of Contents

Operation Section

1. PRECAUTIONS FOR SAFETY

1.1 Foreword. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Definition of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2. CONSTRUCTION

2.1 Exterior Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Exterior Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3 Internal Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 Basic Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.5 Air Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.6 Compressor and Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.7 Drain Tank. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3. SPECIFICATIONS

3.1 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.2 Characteristics in Cool Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.3 Characteristics in Heat Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4. REFRIGERATION SYSTEM

4.1 Refrigeration System Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

4.2 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

4.3 Outdoor Heat Exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

4.4 Indoor Heat Exchanger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

4.5 High Pressure Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.6 Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

4.7 Electronic Expansion Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4.8 4-Way Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4.9 Drain Pan for Outdoor Heat Exchanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

5. ELECTRICAL SYSTEM

5.1 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

5.2 Basic Operation of Electrical Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

5.3 Service Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

5.4 Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

5.5 Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table of Contents

5.6 Power Cord with LCDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

5.7 Drain Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

5.8 Condensate Pump Kit (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5.9 Automatic Restart after Power Interruption (Automatic Recovery Feature) . . . . . . . . . . . . . . . . . . . 41

5.10 Compressor Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5.11 Temperature Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

6. EXTERNAL DEVICE CONNECTION

6.1 Millivolt Thermostat Connection (Optional Accessory) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

6.2 24VAC Thermostat Connection (Field Supplied) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

6.3 Warning Device Connection (Field Supplied) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

6.4 Alarm Device Connection (Field Supplied) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

7. CONTROL PANEL

7.1 Control Panel and LCD Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

7.2 Operational Status Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

7.3 Record Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Table of Contents

Repair Section

8. TROUBLESHOOTING

8.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

8.2 Self-Diagnostic Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

8.3 Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

8.4 Basic Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

9. DISASSEMBLY

9.1 Unit Parts Construction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

9.2 Removal of Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

9.3 Removal of Electrical Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

9.4 Removal of Blower Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

9.5 Inspection of Capacitor (for Fan Motor and Compressor) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

9.6 Inspection of Drain Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

9.7 Inspection of Fan Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

9.8 Inspection of Compressor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

9.9 Inspection of Transformer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

9.10 Inspection of Electronic Expansion Valve Control Coil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

9.11 Inspection of 4-Way Valve Controller Coil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

9.12 Inspection of Thermistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

9.13 Inspection of Wiring Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

9.14 Inspection of Refrigeration System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

10. REFRIGERATION SYSTEM REPAIR

10.1 Repair of Refrigeration System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

10.2 Removal of Refrigeration Cycle Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88

10.3 Charging the System with R-410A Refrigerant. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

10.4 Refrigerant Charging Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

11. REASSEMBLY

11.1 Removal of Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

11.2 Compressor Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

11.3 Blower Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

11.4 Wiring Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

11.5 Perform the Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

11.6 Caster Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Operation Section

6

1. PRECAUTIONS FOR SAFETY

1.1 Foreword

• This manual has been published to service the MovinCool Climate Pro 18. Please use this

service manual only when servicing the Climate Pro 18.

1.2 Definition of Terms

1.3 General Precautions

WARNING

• All electrical work should only be performed by qualified electrical technician. Repair to

electrical components by non-certified technicians may result in personal injury and/or

damage to the unit. All electrical components replaced must be genuine MovinCool parts,

purchased from an authorized dealer.

• Disconnect power supply from the unit before performing any service.

• Before replacing any refrigeration components, recover the refrigerant using standard

recovery procedures and equipment.

• When handling refrigerant, always wear proper eye protection and do not allow the

refrigerant to come in contact with your skin.

• Do not expose refrigerant to an open flame.

• The power supply for this unit should be a dedicated single outlet circuit with a UL

recognized short-circuit and ground-fault protective breaker to prevent electrical shock

from the unit.

• When brazing any tubing, always wear eye protection, and work only in a well ventilated

area.

• Be careful of any sharp edges when working on unit.

Describes precautions that should be observed in order to prevent injury to

the user during installation or unit operation.

Describes precautions that should be observed in order to prevent damage to

the unit or its components, which may occur during installation or unit

operation if sufficient care is not taken.

NOTE Provides additional information that facilitates installation or unit operation.

WARNING

CAUTION

Operation Section 7

2. CONSTRUCTION

2.1 Exterior Dimensions

ILL00849-00

Unit: Inch (mm)

19.4 (492)

3.0 (76)

1.4 (35)1.4 (35)

20.8 (527)

27.5 (698)

4.5

(116)

2.2 (55)

DIA. 11.6 (294)

13.2 (336)11.8 (300) 18.5 (469)

21.4 (544)

2.4 (60)43.5 (1105)

3.7 (93)

49.6 (1258)

Operation Section

8

2.2 Exterior Components

ILL00850-00

Service Panel

Indoor Heat Exchanger

Air Inlet Grill

Outdoor Heat Exchanger

Air Inlet Panel

Outdoor Heat Exchanger

Air Outlet Duct

Power Cord

Caster

Drain Tank Cover

Control Panel

Cool/Hot Air Outlet Grill

Operation Section 9

2.3 Internal Structure

ILL00851-00

Outdoor Fan Motor

Indoor Fan

Outdoor Fan

Compressor

Service Box

Connector for Optional

Condensate Pump

Electronic

Expansion Valve

Drain Tank

Indoor Fan Motor

Indoor

Heat Exchanger

Drain Pan

Outdoor

Heat Exchanger

4-Way Valve

Drain Switch

Accumulator

High Pressure

Switch

Operation Section

10

2.4 Basic Construction

• The Climate Pro 18 is compact in construction because the indoor and the outdoor heat

exchangers are enclosed in one unit. The interior is divided into three sections. The upper front

face is equipped with the indoor heat exchanger, and the lower front face contains the drain tank

and condensate pump (optional accessory). The rear section contains the outdoor heat

exchanger, the compressor and the control box.

2.5 Air Flow

• In Cool Mode, air drawn from the outdoor air inlet passes through the heat rejection coil

(condenser) and discharges hot air through the exhaust hot air outlet. Air take in from the indoor

air inlet passes through the heat absorption coil (evaporator) and discharges the cool air through

the cool air outlet.

• In Heat Mode, the refrigeration in the unit operates in reverse cycle and the heat rejection coil

(condenser) becomes the heat absorption coil (evaporator). Air drawn from the outdoor air inlet

passes through this heat absorption coil and discharges cool air through the exhaust cool air

outlet. Air taken in from the indoor air inlet passes through the heat rejection coil and discharges

hot air through the hot air outlet.

ILL00852-00

Exhaust Hot

Air Outlet

Cool Air

Outlet

Indoor Air

Inlet

Outdoor

Air Inlet

Exhaust Cool

Air Outlet

Hot Air

Outlet

Indoor Air

Inlet

Outdoor

Air Inlet

Cool Mode Heat Mode

Operation Section 11

2.6 Compressor and Fans

• The compressor is hermetically sealed. The indoor fan is a centrifugal type and operated by a

3-speed motor to draw air through the indoor air inlet. The outdoor fan is also a centrifugal type

and operated by a 1-speed motor to draw air through the outdoor air inlet.

2.7 Drain Tank

• A 5.0 gal (19 L) drain tank is supplied with the Climate Pro 18. The condensate (water) is

collected into the tank.

The drain switch activates and stops the operation when tank reaches the level of approximately

4.0 gal (15 L).

Operation Section

12

3. SPECIFICATIONS

3.1 Technical Specifications

Technical Specifications - Table 1

< NOTE >

*1 : With outdoor heat exchanger air outlet duct 10 feet (3.0 m) vertical head lift from the ground to the ceiling.

ITEM SPECIFICATIONS

Electronic Features Operation Digital Programmable

Electrical Characteristics Voltage Requirement 1 Phase, 115 V, 60 Hz

Operating Voltage Range Max. 127 V

Min. 104 V

Starting Current 65 A

Recommended Fuse Size 20 A

FLA 15.6 A

LRA 65 A

Cooling Performance

Rating Condition

(AHAM PAC-1-2009)

Indoor Heat Exchanger:

80 °F (26.7 °C), 50 %RH

Outdoor Heat Exchanger:

80 °F (26.7 °C), 50 %RH

Total Cooling Capacity*114,600 Btu/h (4,270 W)

Sensible Cooling Capacity*19,900 Btu/h (2,900 W)

Power Consumption*11.54 kW

Current Consumption*114.1 A

SD-EER 9.5

Power Factor 95 %

Heating Performance

Rating Condition

(AHAM RAC-1-2008)

Indoor Heat Exchanger:

70 °F (21.1 °C), 57 %RH

Outdoor Heat Exchanger:

47 °F (8.3 °C), 75 %RH

Total Heating Capacity 13,700 Btu/h (4,010 W)

Power Consumption 1.61 kW

Current Consumption 14.7 A

COP 2.49

Power Factor

95 %

Compressor Type Hermetic Rotary

Output 1.16 kW

Ventilation Equipment for

Outdoor Coil

Type of Outdoor Coil (Heat Exchanger) Plate Fin

Type of Fan Centrifugal Fan

Air Flow 700 CFM (1,190 m3/h)

Max. External Static Pressure 0.23 IWG (57 Pa)

Motor Output 0.135 kW

Operation Section 13

Technical Specifications - Table 2

ITEM SPECIFICATIONS

Ventilation Equipment for

Indoor Coil

Type of Indoor Coil (Heat Exchanger) Plate Fin

Type of Fan Centrifugal Fan

Air Flow High 540 CFM (918 m3/h)

Medium 440 CFM (748 m3/h)

Low 350 CFM (595 m3/h)

Max. External Static Pressure 0.31 IWG (77 Pa)

Motor Output High 0.12 kW

Medium 0.045 kW

Low 0.017 kW

Power Cord NEMA Plug Configuration 5-20

Gage x Length 12 AWG (3-core) x 10 ft (3.0 m)

Refrigerant Refrigerant Control Electronic Expansion Valve

Type R-410A

Amount 1.94 lb (0.88 kg)

Signal Connection Fire Alarm Input 1 (FA-1, FA-2) • No-voltage contact input

• Contact resistance less than 100

ohm

Fire Alarm Input 2 (Al-1, Al-2)

Warning Signal Output (OS-1, OS-2) 2 A at 30 V (DC/AC) max. with resis-

tive load

External Wall Thermostat Millivolt Type With terminals RC, O/B, G, Y

24VAC Type With terminals C, O/B, G, Y,

24VAC RC/RH

Dimension W x D x H 21 x 27 x 50 in

(533 x 686 x 1,270 mm)

Weight Net 214 lb (97 kg)

Shipping 250 lb (113 kg)

Drain Tank Capacity 5.0 gal (19 L)

Cooling Operating Condition

Range

Inlet Air Temperature Max. 95 °F (35 °C), 60 %RH

Min. 65 °F (18 °C), 50 %RH

Heating Operating Condition

Range

Without Outdoor Heat

Exchanger Duct

Max. 80 °F (26.7 °C), 50 %RH

Min. 40 °F (4.4 °C), 50 %RH

With Outdoor Heat

Exchanger Duct

Max. 80 °F (26.7 °C), 50 %RH

Min. Indoor Heat Exchanger:

40 °F (4.4 °C), 50 %RH

Outdoor Heat Exchanger:

24 °F (-4.4 °C), 50 %RH

Operation Section

14

Technical Specifications - Table 3

• Specifications are subject to change without notice.

< NOTE >

*2 : Measured at 3 feet (1.0 m) from surface of the unit.

ITEM SPECIFICATIONS

Maximum Equivalent Duct

Length

Indoor Heat Exchanger Duct 25 ft (7.6 m)

Outdoor Heat Exchanger Duct 100 ft (30.5 m)

Sound Level*2With Outdoor Heat

Exchanger Duct

High 61 dB (A)

Medium 60 dB (A)

Low 59 dB (A)

Without Outdoor Heat

Exchanger Duct

High 62 dB (A)

Medium 61 dB (A)

Low 60 dB (A)

Safety Devices Compressor Overload Protector Included

Fan Motor Overload Protector (Indoor/Outdoor) Included

Freeze Protection Thermistor Included

Drain Switch Included

Automatic Restart (Power Interruption) Included

Compressor Time Delay Included

High Pressure Interruption Included

Signal Input/Output Included

Current Fuse for Relay Board Included

Current Fuse for Drain Pan Heater and 4-Way

Valve Included

Cutoff Fuse for Drain Pan Heater Included

Control Devices Defrost Heating Included

Drain Pan Heater Heating Included

Delay Timer for Indoor

Fan

Cooling Not included

Heating Included

Temperature Control Included

Programmable Timer Included

3-Speed Fan Included

Loss of Cooling or Heating Included

On-Screen Self-Diagnostic Codes Included

Operation Section 15

3.2 Characteristics in Cool Mode

• All characteristic values are within ±10% tolerance.

(1) Cooling capacity curve

ILL00853-00

Cooling Capacity (kBtu/h)Relative Humidity (%)

Wet Bulb Temp. ºF (ºC)

11

17

16

15

14

40

50

60

70

80

90

100

13

12

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

Dry Bulb Temp. ºF (ºC)

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

Hi

Mid

Lo

Operation Section

16

How to read the cooling capacity curve

ILL00854-00

Cooling Capacity (kBtu/h)

11

17

16

15

14

13

12

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

Example: Dry bulb: 80 ºF (27 ºC), 50 %RH, High fan speed



Cooling capacity:14.6 kBtu/h

Relative Humidity (%)

Wet Bulb Temp. ºF (ºC)

40

50

60

70

80

90

100

Dry Bulb Temp. ºF (ºC)

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

Hi

Mid

Lo

Operation Section 17

(2) Power consumption curve

How to read the power consumption curve

Power Consumption (W)Relative Humidity (%)

Wet Bulb Temp. ºF (ºC)

1.1

40

60

80

100

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

Dry Bulb Temp. ºF (ºC)

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

1.9

1.8

1.7

1.6

1.5

1.4

1.3

1.2

Hi

Mid

Lo

ILL00855-00

Power Consumption (W)Relative Humidity (%)

Wet Bulb Temp. ºF (ºC)

1.1

40

50

60

80

100

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

Dry Bulb Temp. ºF (ºC)

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

1.9

1.8

1.7

1.6

1.5

1.4

1.3

1.2

Example: Dry bulb: 80 ºF (27 ºC), 50 %RH, High fan speed



Power consumption : 1.54 kW

Hi

Mid

Lo

ILL00856-00

Operation Section

18

(3) Current consumption curve

How to read the current consumption curve

ILL00857-00

Current Consumption (A)Relative Humidity (%)

Wet Bulb Temp. ºF (ºC)

10

40

60

80

100

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

Dry Bulb Temp. ºF (ºC)

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

18

17

16

15

14

13

12

11

Hi

Mid

Lo

Current Consumption (A)Relative Humidity (%)

Wet Bulb Temp. ºF (ºC)

10

40

50

60

80

100

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

Dry Bulb Temp. ºF (ºC)

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

90

(32)

95

(35)

Example: Dry bulb: 80 ºF (27 ºC), 50 %RH, High fan speed

 Current consumption : 14.2 A

18

17

16

15

14

13

12

11

Hi

Mid

Lo

ILL00858-00

Operation Section 19

(4) Cool air temperature difference curve

ILL00859-00

Relative Humidity (%)

15 (8.3)

20 (11.1)

25 (13.9)

30 (16.7)

30 40 50 60 70 80

10 (5.6)

Delta-T ºF(ºC)

Hi Mid Lo

Operation Section

20

3.3 Characteristics in Heat Mode

• All characteristic values are within ±10% tolerance.

(1) Heating capacity curve

ILL00881-00

35

(2)

40

(4)

45

(7)

50

(10)

55

(13)

60

(16)

65

(18)

70

(21)

75

(24)

80

(27)

85

(29)

Heating capacity (kBtu/h)

Dry Bulb Temp. ºF (ºC)

10

12

14

16

18

20

Hi

Lo

Mid

Page is loading ...

Movincool CPD12 Installation guide

This manual is also suitable for

Movincool CPD12 Installation guide

Related papers

Other documents