GreenBrook DHT01AN Operating instructions

Type
Operating instructions

GreenBrook DHT01AN is a dual-tone door chime with a built-in transformer and bell push. It is powered by a 240V supply and can be connected to an appropriate cable (not supplied) to the screwless bell-push terminals inside the doorchime. The bell push can be secured in its position and the doorchime front cover can be replaced. The chime should not be mounted on the door. For longer cable runs, a cable with a larger cross-sectional area is advised, e.g., 13 strand speaker flex.

GreenBrook DHT01AN is a dual-tone door chime with a built-in transformer and bell push. It is powered by a 240V supply and can be connected to an appropriate cable (not supplied) to the screwless bell-push terminals inside the doorchime. The bell push can be secured in its position and the doorchime front cover can be replaced. The chime should not be mounted on the door. For longer cable runs, a cable with a larger cross-sectional area is advised, e.g., 13 strand speaker flex.

PLEASE ENSURE YOU READ THESE
INSTRUCTIONS BEFORE COMMENCING
ANY INSTALLATION
This unit should be installed by a
competent person in accordance with the
current IET Wiring Regulations.
If in doubt consult a qualified electrician.
Switch off the mains and isolate the supply
by removing the appropriate fuse before
starting the installation.
Instructions for
‘Embassy’ Doorchime
with Built-in Transformer
& Bell Push
Model: DHT01AN
1. Remove front cover of the chime.
2. Remove mains terminal cover.
3. Mount the back section of the
doorchime to the wall using the fixing
screws.
4. Connect a 240V supply to the live and
neutral screwless terminals - it does not
matter which way round the live/neutral
wires go. Replace mains terminal cover.
5. Connect appropriate cable (not
supplied) to the screwless bell-push
terminals inside the doorchime (see
diagram) and route to the bell push
position.
INSTALLATION
IMPORTANT
Dual tone chime
Powered by internal transformer
Bellpush and woodscrews are supplied
Not suitable for illuminating bell pushes
DHT01AN Ins Apr 22_Layout 1 20/05/2022 11:48 Page 1
6. Remove bell push front cover.
7. Connect the other end of the bell wire
to the bell push terminals.
8. Secure the bell push in its position.
9. Replace the bell push front cover.
10. Replace the doorchime front cover.
11. Switch on the electricity at the fuse box
by replacing the relevant fuse or
switching on the circuit breaker after
completing the installation.
For longer cable runs, cable with a larger cross
sectional area is advised, e.g. 13 strand speaker flex.
Note: Do not mount chime on door.
Issue no: 706919
GUARANTEE
Your GreenBrook Wired Doorchime Kit is
guaranteed for 1 year from the date of purchase.
This is in addition to your statutory rights.
PLEASE KEEP THESE INSTRUCTIONS
SAFE FOR FUTURE REFERENCE
WEST ROAD . HARLOW
ESSEX . CM20 2BG . UK
info@greenbrook.co.uk
www.greenbrook.co.uk
4.5V DC
NOTE: Product & Packaging Disposal
When disposing of this item and its packaging please
follow local regulations and use an appropriate waste
disposal centre.
See GreenBrook website for further details.
DHT01AN Ins Apr 22_Layout 1 20/05/2022 11:48 Page 2
  • Page 1 1
  • Page 2 2

GreenBrook DHT01AN Operating instructions

Type
Operating instructions

GreenBrook DHT01AN is a dual-tone door chime with a built-in transformer and bell push. It is powered by a 240V supply and can be connected to an appropriate cable (not supplied) to the screwless bell-push terminals inside the doorchime. The bell push can be secured in its position and the doorchime front cover can be replaced. The chime should not be mounted on the door. For longer cable runs, a cable with a larger cross-sectional area is advised, e.g., 13 strand speaker flex.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI