Page is loading ...
By
Patient
User Guide
May, 2011
Version 1.1
PLEASE NOTE
MDwave is complaint with the following
standards:
FCC Part 18
CE 60601-1 and 2
MDwave is certified as non harmful to the
body
MDwave is not a medical device.
MDwave Unit Overview
MDwave is a computerized frequency generator
device. The battery-powered unit uses a coil-based
flat pad to generate a magnetic flux that transmits
the designated frequencies to the patient.
MDwave Components
The MDwave unit has two components:
Control panel – ON and OFF buttons and
status LEDs.
Flat pad – Placed on the patient during
treatments.
During operation, the flat pad should be connected
to the control panel, as can be seen in the
following figure.
Figure 1: MDwave Unit
MDwave Control Panel
The control panel has power buttons and status
LEDs. It also has connection ports for the flat pad
and the USB cable that connects to the computer.
The following diagram shows the control panel.
Figure 2: MDwave Control Panel
The following table describes the MDwave
controls.
Table 1: MDwave Control Panel
Number
Explanation
1
ON and OFF power buttons.
2
Signal and Power status LEDs:
Power – Green LED lights when the unit
is on.
Output – Yellow LED lights when the unit
is transmitting.
Number
Explanation
3
Connection ports:
PC – USB cable connects to the
computer.
Coil – Connects to the flat pad.
Aux – 6 pin PCS connector,
currently not used.
4
Buzzer for audible alerts.
During treatment – Used for
troubleshooting.
Before treatment – Indicates the
treatment number.
The Output LED indicates the transmission status of
the treatments:
Off – No treatment is in process.
Slow flashing – The unit is currently being
used for a treatment program, but is in a
rest interval and is not transmitting.
Fast flashing – The unit is currently being
used for a treatment program, and is
transmitting.
Performing a Treatments
When treatments have been programmed to the
MDwave unit, the unit can control treatment
administration without the use of a computer. It is
fully self sufficient, and battery operated.
Use the following procedure to perform treatments.
To perform treatments:
1. Make sure the Flat Pad of the MDwave is well
connected to the unit.
2. Turn on the MDwave unit. Press and hold the
ON button until the green power LED is on.
3. The yellow light flashes while the unit beeps, to
indicate which of the stored treatments will be
activated. (Up to 4 treatments can be stored. The
number of beeps indicate to the chosen treatment
number). Then, the yellow light flashes . It will
flash quickly when a frequency is transmitted and
will flash slowly during idle intervals between
frequencies.
4. To access a treatment when there is more than
one treatment available, turn the MDwave unit ON
and OFF until you reach the required treatment.
Or, to move from one treatment to another, turn
the unit on and press the OFF button quickly until
you reach the desired treatment.
Troubleshooting
NOTE:
Each time you turn the unit on, a treatment
starts automatically.
The MDwave unit shuts off automatically at
the end of the treatment.
The battery’s life cycle is approximately 17
hours of treatment time.
The following table describes troubleshooting
solutions.
Table 2: Troubleshooting
Indicator
Explanation
The MDwave unit beeps
three times and then
turns itself off.
The Flat Pad is disconnected.
The green light is
flashing.
Battery is low.
The green light is
flashing & continues
beeps are heard.
The battery needs immediate
replacing.
Use a standard 9V alkaline
battery.
The MDwave unit beeps
every three seconds
The flat pad is disconnected.
Reconnect properly to stop the
beeping.
Short beep during
treatment
Ignore
Contact Information
If you need further assistance for sales or
support, contact us at:
Aerotel LTD.
Holon, Israel
Phone: +972-3-558-5515
Fax: +972-3-558-5516
e-mail: MDwave.tech@gmail.com
http://www.aerotel.co.il
/
