FUSION Electronics CS-CM50 Specification

Brand
FUSION Electronics
Model
CS-CM50
Category
Car speakers
Type
Specification

FUSION Electronics CS-CM50 boasts impressive audio capabilities with 220 Watts peak power and 35 Watts rated power, delivering crystal-clear sound. Its frequency response ranges from 41Hz to 26kHz, capturing a wide spectrum of audio frequencies. Made with durable polypropylene cones and PEI tweeters, this speaker system ensures high-fidelity audio reproduction. With a mounting depth of 43mm and a mounting diameter of 118mm, it fits various vehicle audio setups. Experience exceptional sound quality that enhances your driving experience with the FUSION Electronics CS-CM50.

FUSION Electronics CS-CM50 boasts impressive audio capabilities with 220 Watts peak power and 35 Watts rated power, delivering crystal-clear sound. Its frequency response ranges from 41Hz to 26kHz, capturing a wide spectrum of audio frequencies. Made with durable polypropylene cones and PEI tweeters, this speaker system ensures high-fidelity audio reproduction. With a mounting depth of 43mm and a mounting diameter of 118mm, it fits various vehicle audio setups. Experience exceptional sound quality that enhances your driving experience with the FUSION Electronics CS-CM50.

COMPONENT SPEAKER SYSTEMS
CS-CM50 CS-CM60
PeakPower(Watts) 220 240
RatedPower(Watts) 35 40
FrequencyResponse 41Hz-26kHz 35Hz-26kHz
Impedance 4Ohms 4Ohms
Sensitivity 85dB 86dB
ConeMaterial Polypropylene Polypropylene
Tweeter PEI PEI
MountingDepth 43mm(1-11/16”) 45.5mm(1-13/16”)
MountingDiameter 118mm 126mm
(4-21/32”) (5”)
CS-CM50 CS-CM60
WARNING:Donotdrillmountingholeswithspeakerinplaceasthiscouldallowdrillshavingstodamagethe
voicecoilandvoidyourwarranty.
SPEAKER PARAMETERS
www.fusionelectronics.com
TWEETER
Ø53mm
(2-1/16”)
9mm(11/32”)
20mm(25/32”)
47mm
(1-27/32”)
INSTALLATION GUIDELINES
Ensuretheaudiosystemisturnedoffbeforemakinganyconnections
totheamplier,speakersorsourceunit.Failuretodosocouldresultin
permanentdamagetotheaudiosystem.
Whenwiringthespeakersensurethatthewireisprotectedfromsharp
objectsandalwaysuserubbergrommetswhenwiringthroughmetal
panels.Ensureallterminalsandconnectionsareprotectedfromthe
vehiclechassisandfromeachotherasfailuretodosocouldresultin
permanentdamagetotheaudiosystem.
Whenconnectingthesourceunitandspeakersensureyouconnect
thepositiveandnegativeoutputwirefromthesourceunittothe
correspondingspeakerterminals.Thiswillensuretheaudiosystemwill
beinphase.
1) Ensurethereisadequateclearance&depthforthespeakertobe
mounted
2) Usethesuppliedtemplatetomarkout&cutthecorrectdiameterhole
3) Drillfourholesforthemountingscrews
4) Seperatethegrillefromtheframe
5) Insertthespeaker&grilleframeandafxwiththescrewsprovided
6) Completeinstallionbyreplacingthegrilleintothegrilleframe
TWEETER (Surface/Angle mount)
To obtain the best performance from the tweeter it should be located on axis to approximately 4” below the rear
view mirror. Select the mount you require and use this as a template to drill the holes to mount or alternatively
if using an adhesive pad ensure the mounting surface is cleaned with a residue free cleaner and stick the
tweeter down. Attach the wires to the speaker terminals.
TWEETER (Flush mount)
Ensure you have adequate depth to mount the tweeter and cut a 47mm hole. Assemble the rear mount with the
spring clamp and press through from the rear of the hole, then attach the front plate to the rear plate as shown
in the illustration. Attach the wires to the speaker terminals.
PUBLISHED BY FUSION ELECTRONICS LIMITED: © Copyright 2010 by FUSION Electronics Limited. All rights reserved. Specications and design are subject to change without notice.
YOU CAN HELP PROTECT THE ENVIRONMENT! Please remember to respect the local regulations: Hand in the non-working electrical equipment to an appropriate waste disposal center.
RECORD YOUR PURCHASE DETAILS HERE:
SERIAL NUMBER
DATE OF PURCHASE
AFFIX RECEIPT HERE
WARNING: Audio Systems can produce sound levels over 135dB. Continuous exposure to sound pressure levels over 100dB may cause permanent
hearing loss! Please watch for emergency vehicles as warning signals may not be heard. USE COMMON SENSE!
For further product and installation information, please visit www.fusionelectronics.com
Pour plus d’informations sur les produits et l’installation, rendez-vous sur www.fusionelectronics.com
Para obtener más información acerca de los productos y de su instalación, visite el sitio web www.fusionelectronics.com
Bezoek www.fusionelectronics.com voor meer product- en installatie-informatie.
Weitere Produkt- und Installationsinformationennden Sie unter www.fusionelectronics.com
Per ulteriori informazioni sui prodotti e la loro installazione, potete visitare www.fusionelectronics.com
Для получения дополнительной информации о продуктах и установке зайдите, пожалуйста, на: www.fusionelectronics.com
  • Page 1 1
  • Page 2 2

FUSION Electronics CS-CM50 Specification

Brand
FUSION Electronics
Model
CS-CM50
Category
Car speakers
Type
Specification

FUSION Electronics CS-CM50 boasts impressive audio capabilities with 220 Watts peak power and 35 Watts rated power, delivering crystal-clear sound. Its frequency response ranges from 41Hz to 26kHz, capturing a wide spectrum of audio frequencies. Made with durable polypropylene cones and PEI tweeters, this speaker system ensures high-fidelity audio reproduction. With a mounting depth of 43mm and a mounting diameter of 118mm, it fits various vehicle audio setups. Experience exceptional sound quality that enhances your driving experience with the FUSION Electronics CS-CM50.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents