Chief TS110SU Installation guide

TS110SU
Chief
Brand
Chief
Model
TS110SU
Category
Flat panel wall mounts
Type
Installation guide

This manual is also suitable for

Chief TS110SU is a small thinstall swing arm designed for mounting TVs and displays weighing up to 35 lbs. Its compact design allows it to be installed in tight spaces, making it ideal for smaller rooms or areas where space is limited. The TS110SU features smooth panning and tilting adjustments, allowing you to easily position your TV or display for optimal viewing angles. It also includes a built-in cable management system to keep cords organized and out of sight.

Chief TS110SU is a small thinstall swing arm designed for mounting TVs and displays weighing up to 35 lbs. Its compact design allows it to be installed in tight spaces, making it ideal for smaller rooms or areas where space is limited. The TS110SU features smooth panning and tilting adjustments, allowing you to easily position your TV or display for optimal viewing angles. It also includes a built-in cable management system to keep cords organized and out of sight.

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
TS110SU
TS118SU
Small Thinstall™ Swing Arm
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
TS110SU/TS118SU
TS110SU/TS118SU Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® and Thinstall™ are registered trademarks of Milestone
AV Technologies. All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
SAVE THESE INSTRUCTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm) if it is
being installed to wood studs. Do NOT install to a concrete
wall of any kind that has a drywall covering!
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached does not exceed 35 lbs (15.9 kg).
Use with products heavier than the maximum weight
indicated may result in collapse of the mount and its
accessories causing possible injury.
IMPORTANT ! : The TS110SU/TS118SU mounts are
designed to be mounted to an 8" concrete, 8"x8"x16" concrete
block, clay brick or 2" x 4" wood studs (16" on center).
Installation Instructions TS110SU/TS118SU
3
DIMENSIONS - TS110SU
DIMENSIONS - TS118SU
8.55
217.3
SCREEN CENTER
COMPATIBLE MOUNTING PATTERNS INCLUDE:
75 X 75, 100 X 100, 200 X 100, 200 X 200
1.49
37.9
MINIMUM
DISTANCE
FROM WALL
9.85
250.1
MAXIMUM
EXTENSION
FROM WALL
12.0°
MAX
7.37
187.1
9.09
230.9
.08
FACEPLATE
THICKNESS
90 PAN
LEFT/RIGHT
6.24
158.6
.27
6.7
2.62
66.5
SCREEN
TO TOP
LAG BOLT
9.51
241.6
6.43
163.3
SCREEN CENTER
COMPATIBLE MOUNTING PATTERNS INCLUDE:
75 X 75, 100 X 100, 200 X 100, 200 X 200
1.50
38
MIN.
DISTANCE
FROM WALL
18.01
457.5
MAX
EXTENSION
FROM WALL
12.0°
MAX
TILT
6.05
153.7
2.49
63.2
1.06
26.9
9.09
230.9
PAN
LEFT/RIGHT
.27
6.73
1.00
25.4
SCREEN
CENTER
TO TOP
LAG BOLT
Installation Instructions TS110SU/TS118SU
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
TS110SU/TS118SU Installation Instructions
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/8" - wood studs #2
7/16" (11.1mm)
8mm - concrete
concrete only
H (1)
D2 (4)
"A"
"B"
"C"
"D"
A1 (4)
M4x12mm
A2 (4)
M4x16mm
A3 (4)
M4x25mm
B1 (4)
M5x12mm
B2 (4)
M5x16mm
B3 (4)
M5x25mm
C1 (4)
M6x12mm
C2 (4)
M6x16mm
C3 (4)
M6x25mm
M5
J (1)
[main assembly]
E (2)
1/4 x 2 1/2"
F (2)
[concrete anchor]
G (1)
3/16"
D3 (8)
1/4"
D1 (4)
M4
[wall cover]
H (1)
[main assembly]
J (1)
[wall cover]
TS118SU
TS110SU
TS110SU/TS118SU Installation Instructions
6
Assembly And Installation
Install to Wall
Install Main Assembly to Wall - Wood Studs
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. The wall to which the mount is being attached
may have a maximum drywall thickness of 5/8" (1.6cm).
1. Determine mounting location using a stud finder to locate a
wood stud.
2. Measure 2 5/8" above desired center line if mounting
TS110SU or 1" below desired center line if mounting
TS118SU and mark a hole at this location. (See Figure 1)
IMPORTANT ! : Use a level to make sure main assembly
(H) is level when mounted to the wall!
IMPORTANT ! : The TS110SU/TS118SU mounts are
designed to be mounted to a 2" x 4" wood studs (16" on center)
wall.
3. Drill one 1/8" hole at location marked in Step 2. (See Figure
1)
Figure 1
4. Install one 1/4 x 2 1/2" lag bolt (E) into hole, leaving screw
hanging out 1/2" from the wall. (See Figure 2)
5. Hang main assembly (H) onto lag bolt (E) by latching key-
shaped hole over top of bolt. (See Figure 2)
Figure 2
6. Mark holes at lower mounting hole location. (See Figure 3)
7. Remove main assembly (H) from wall.
8. Drill 1/8" hole at location marked in Step 6. (See Figure 3)
9. Hang main assembly (H) back onto wall.
10. Install remaining 1/4 x 2 1/2" lag bolt (E) into hole drilled in
Step 8 to secure mount to wall. (See Figure 3)
11. Tighten both lag bolts (E) to fully secure mount to wall.
Figure 3
12. Proceed ahead to Display Installation Section on page 8.
2
3
1/8"
screen
center
2 5/8"
TS118SU
TS110SU
screen
center
1"
(E)
5
1/2"
4
(H)
(TS110SU shown)
(E)
10
6
8
(H)
(TS110SU shown)
Installation Instructions TS110SU/TS118SU
7
Install Main Assembly to Wall - Hollow
Concrete Block, Poured Concrete or Clay
Brick
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component. Do NOT install to a concrete wall of any kind that
has a drywall covering!
WARNING: INSTALLING THE TS110SU/TS118SU INTO
UNDERRATED OR DAMAGED CONCRETE CAN LEAD TO
SERIOUS INJURY OR DAMAGE TO PRODUCT! Never
install the TS110SU/TS118SU into cracked, chipped or
flaking concrete.
1. Determine mounting location.
2. Measure 2 5/8" above desired center line if mounting
TS110SU or 1" below desired center line if mounting
TS118SU and mark a hole at desired mounting location.
(See Figure 4)
IMPORTANT ! : Use a level to make sure main assembly
(H) is level when mounted to the wall!
IMPORTANT ! : The TS110SU/TS118SU mounts are
designed to be mounted to an 8" concrete, 8"x8"x16" concrete
block or clay brick wall.
3. Drill one 8mm hole at location marked in Step 2. (See Figure
4)
Figure 4
4. Install one concrete anchor (F) into drilled hole. (See Figure
5)
5. Install one 1/4 x 2 1/2" lag bolt (E) into concrete anchor (F),
leaving bolt hanging out 1/2" from the wall. (See Figure 5)
6. Hang main assembly (H) onto lag bolt (E) by latching key-
shaped hole over top of bolt. (See Figure 5)
Figure 5
7. Mark hole at lower mounting hole location. (See Figure 6)
8. Remove main assembly (H) from wall.
9. Drill 8mm hole at marked location. (See Figure 6)
10. Install remaining concrete anchor (F) into drilled hole. (See
Figure 6)
11. Hang main assembly (H) back onto wall.
12. Install remaining 1/4 x 2 1/2" lag bolt (E) into concrete
anchor (F) to secure mount to wall. (See Figure 6)
13. Tighten both lag bolts (E) to fully secure mount to wall.
Figure 6
2
3
8mm
screen
center
2 5/8"
TS118SU
TS110SU
screen
center
1"
(E)
6
1/2"
5
4
(F)
(E)
(F)
(TS110SU shown)
(E)
12
7
9
10
(F)
(TS110SU shown)
TS110SU/TS118SU Installation Instructions
8
Display Installation
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached does not exceed 35 lbs (15.9 kg).
Use with products heavier than the maximum weight
indicated may result in collapse of the mount and its
accessories causing possible injury.
CAUTION: Using screws of improper diameter may
damage your display! Proper screws will easily thread into
display mounting holes.
NOTE: Compatible mounting patterns for the TS110SU and
TS118SU include 75mm x 75mm, 100mm x 100mm,
200mm x 100mm and 200mm x 200mm.
1. Select screw diameter by examining hardware (A-C) (4mm,
5mm or 6mm) and comparing with mounting holes on
display.
CAUTION: Using screws of improper length may damage
your display! Proper screws will have adequate thread
engagement without contacting bottom of display mounting
holes.
2. Select screw length:
• Using your hand, insert SHORTEST length screw
of selected diameter (A1, B1 or C1) into display
mounting hole. Do NOT fully thread screw into
hole at this time.
3. Install two selected screws (A-C) into upper two holes on
back of display. (See Figure 7)
IMPORTANT ! : If using M4 or M5 screws (A or B),
washer hardware (D1 or D2) should be used to ensure
tight fit into the faceplate holes!
IMPORTANT ! : For recessed mounting holes or to gain
extra space, 1/4" spacers (D3) may be used in between
the back of the display and the faceplate. Multiple
spacers may be used on each screw if more space is
needed.
4. Hang display by two screws onto faceplate through either
inner or outer teardrop mounting holes. (200x200 mounting
pattern shown) (See Figure 8)
5. Install two selected screws (A-C) through selected washer
hardware (D1 or D2 if necessary), lower holes on faceplate
and into lower two holes on display. (See Figure 8)
IMPORTANT ! : For recessed mounting holes or to gain
extra space, 1/4" spacers (D3) may be used in between
the back of the display and the faceplate. Multiple
spacers may be used on each screw if additional space
is required.
6. Tighten all hardware to ensure display is securely mounted.
Figure 7
Figure 8
(A-C) x 2
3
(D2) x 2 with (B)
(D1) x 2 with (A)
or
4
5
(A-C) x 2
(200 x 200 shown on TS110SU)
(D2) x 2 with (B)
(D1) x 2 with (A)
or
Installation Instructions TS110SU/TS118SU
9
Wall Cover Installation
CAUTION: Wall covers are fragile and may be damaged or
broken if installed with excessive force! Use caution when
installing and removing wall covers.
1. Pull apart top or bottom section of wall cover (J) so that it fits
over the main assembly arm. For the TS110SU pull apart
the top and for the TS118SU pull apart the bottom. (See
Figure 9) or (See Figure 10)
2. Install wall cover (J) onto main assembly making sure holes
on cover latch over tabs on main assembly. (See Figure 9)
or (See Figure 10)
Figure 9
Figure 10
Cable Management
1. Make all cable connections to display.
2. Open cable management covers on upper and lower swing
arms by unhinging center tabs and lifting covers to the open
position. (See Figure 11)
Figure 11
3. Route cables on top of upper arm. (See Figure 12)
NOTE: Cable ties (not included) may be used to secure cables
to back of faceplate using cable tie holes on either side
of faceplate.
4. (Optional) Use cable ties (not included) to secure cables to
upper arms by threading ties around cable and through
cable tie holes inside the covers. (See Figure 12)
5. Close upper cable management cover. (See Figure 12)
6. (TS118SU only) Route cables under lower portion of swing
arm. (See Figure 12)
7. (Optional for TS118SU only) Use cable ties (not included) to
secure cables to lower arms by threading ties around cable
and through cable tie holes inside the covers. (See Figure
12)
8. (TS118SU only) Close lower cable management cover.
(See Figure 12)
Figure 12
1
2
1
(H)
(J)
TS110SU
1
2
1
TS118SU
(J)
(H)
2
center tabs
2
3
4
cable ties
(not included)
6
cable (typical)
(TS118SU shown)
TS110SU/TS118SU Installation Instructions
10
Tilt Friction Adjustment
1. Adjust tilt friction adjustment screws to increase or decrease
tilt friction. (See Figure 13)
NOTE: There is a tilt friction adjustment screw on each side of
the pitch mechanism that must be adjusted evenly in
order to properly adjust tension.
Figure 13
Arm Tension Adjustment
1. Use 3/16" hex key (T) to adjust arm tension at any of the
tension adjustment points. (See Figure 14) or (See Figure
15)
Figure 14
Figure 15
(side view of TS110SU)
arm tension
adjustment points
(TS110SU)
arm tension
adjustment points
(TS118SU)
Installation Instructions TS110SU/TS118SU
11
TS110SU/TS118SU Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products divi-
sion of Milestone AV Technologies
8832-002076 REV 03
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
05/12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Chief TS110SU Installation guide

TS110SU
Chief
Brand
Chief
Model
TS110SU
Category
Flat panel wall mounts
Type
Installation guide
This manual is also suitable for

Chief TS110SU is a small thinstall swing arm designed for mounting TVs and displays weighing up to 35 lbs. Its compact design allows it to be installed in tight spaces, making it ideal for smaller rooms or areas where space is limited. The TS110SU features smooth panning and tilting adjustments, allowing you to easily position your TV or display for optimal viewing angles. It also includes a built-in cable management system to keep cords organized and out of sight.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents