July 2009
FCC Warning
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC Rules. These limitations are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and receiver.
*Connect the equipment into a different outlet from that the receiver is connected.
*Consult your local distributors or an experienced radio/TV technician for help.
*Shielded interface cables must be used in order to comply with emission limits
Notice
Changes or modifications to the equipment, which are not approved by the party
responsible for compliance could affect the user's authority to operate the equipment.
Copyright
2009 All Rights Reserved.
No part of this document can be copied or reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Contents _____
1. Introduction ............................................................................................................... 5
1.1 Features ........................................................................................................................ 5
1.2 Package Contents ....................................................................................................... 6
1.3 LEDs Indication & Connectors of Broadband Router .............................................. 6
1.4 System Requirements ................................................................................................. 7
1.5 Installation Instruction ................................................................................................ 7
2. PC Configuration ...................................................................................................... 7
2.1 TCP/IP Networking ...................................................................................................... 8
3. Setup Broadband Router Configurations via Web Browser ............................... 13
3.1 Start your Web Browser ............................................................................................ 13
3.2 Quick Setup ................................................................................................................ 13
3.3 Administrator ............................................................................................................. 14
3.3.1 Management .................................................................................................. 14
3.3.2 System Settings ............................................................................................ 15
3.3.3 Firmware Upgrade ......................................................................................... 16
3.3.4 Configuration ................................................................................................. 17
3.3.5 Tools ............................................................................................................... 17
3.3.6 Language ....................................................................................................... 18
3.3.7 Log Settings ................................................................................................... 18
3.3.8 Logout ............................................................................................................ 18
3.4 WAN ............................................................................................................................ 19
3.5 LAN ............................................................................................................................. 25
3.5.1 LAN Settings .................................................................................................. 25
3.5.2 DHCP Client List ............................................................................................ 25
3.6 NAT ............................................................................................................................. 27
3.6.1 Virtual Server ................................................................................................. 27
3.6.2 Port Triggering .............................................................................................. 27
3.6.3 Port Mapping ................................................................................................. 28
3.6.4 Passthrough .................................................................................................. 30
3.6.5 DMZ ................................................................................................................. 30
3.7 Firewall ....................................................................................................................... 31
3.7.1 Firewall Options ............................................................................................ 31
3.7.2 Client Filtering ............................................................................................... 32
3.7.3 URL Filtering .................................................................................................. 32
3.7.4 MAC Filtering ................................................................................................. 33
3.8 Routing ....................................................................................................................... 34
3.8.1 Routing Table ................................................................................................ 34
3.8.2 Static Routing ................................................................................................ 34
3.8.3 Dynamic Routing ........................................................................................... 34
3.9 Misc ............................................................................................................................. 35
3.9.1 UPnP ............................................................................................................... 35
3.9.2 DDNS .............................................................................................................. 35
3.10 Status ........................................................................................................................ 36
3.10.1 Status ........................................................................................................... 36
3.10.2 Log ................................................................................................................ 36
1. Introduction ______
Congratulations on purchasing the Broadband Router. This Broadband Router, is a high quality and reliable Internet
routing device, enables multiple users to share the Broadband Internet connection through a Cable or DSL modem.
Simply install the router, connect to Cable/DSL modem, and surf Internet without extra efforts. Acting as a 10/100Mbps
4-port Ethernet switch as well, the router, with all ports supporting MDI/MDIX, allows you to use CAT5 cable to uplink to
other routers/switches. The Broadband Router provides a total solution for the Small and Medium-sized Business
(SMB) and the Small Office/Home Office (SOHO) markets, giving you an instant network today, and the flexibility to
handle tomorrow's expansion and speed.
1.1 Features
Internet Access Features
● Shared Internet Access: All users on the LAN can access the Internet through the Broadband Router, using only a
single external IP address. The local (invalid) IP addresses are hidden from external sources. This process is called
NAT (Network Address Translation).
● DSL and cable modem Support: The Broadband Router has a 10/100BaseT Ethernet WAN port for connecting a
DSL or cable modem. All popular DSL and cable modems are supported.
● PPPoE and PPTP Support: The Internet (WAN port) connection supports PPPoE (PPP over Ethernet) and PPTP
(Point-to-Point Tunneling Protocol), as well as “Direct Connection” type services.
● Fixed or Dynamic IP Address: On the Internet (WAN port) connection, the Broadband Router supports both
Dynamic IP address (IP address is allocated on connection) and Fixed IP address.
Advanced Internet Functions
● Conferencing & Telephony Applications: Internet Telephony and Conferencing applications are supported.
● DMZ: One PC on your local LAN can be configured to allow unrestricted 2-way communication with Servers or
individual users on the Internet.
● URL Filter: Use the URL Filter to block access to undesirable Web sites by LAN users.
● Internet Access Log: This feature is used to verify which Internet connections have been made.
LAN Features
● 4-Port Ethernet Switch: The Broadband Router provides 4 10/100Base-T switching ports.
● Standard Compliance: The Broadband Router complies with the IEEE 802.3x full duplex flow control.
● DHCP Server Support: This feature provides a dynamic IP address to PCs and other devices upon request. The
Broadband Router can act as a DHCP Server for devices on your local LAN.
● Multi Segment LAN Support: This feature is enabled through Broadband Router’s RIP (Routing Information Protocol)
and build-in static routing table.
Configuration and Management
● Easy Setup: Users allow to configure Broadband Router from anywhere on the LAN via web browser.
● Remote Management: The Broadband Router can be managed from any PC on the LAN.
● UPnP Support: Universal Plug and Play feature. UPnP is supported by Windows ME or later.
Security Features
● Password Protected Configuration: Optional password protection is provided to prevent unauthorized users from
modifying the configuration data and settings.
● NAT Protection: This feature allows all LAN users to share a single IP address and all users’ IPs are hidden. From
the external viewpoint, there is no network only the Broadband Router exists.
● Firewall: All incoming data packets are monitored and all incoming server requests are filtered.
1.2 Package Contents
● One Broadband Router
● One External Power adapter
● One CD including user’s manual
1.3 LEDs Indication & Connectors of Broadband Router
Front Panel LEDs Indication
LED Light Status Description
LED Light Status Description
PWR On (Steady Green) Broadband Router is powered on.
Off No power
Status On (Steady Green) System is hung.
Flashing Broadband Router is up and ready.
LAN
(1, 2, 3, 4)
On (Steady Amber) LAN port is successfully connected.
Flashing Data is being sent or received.
WAN On (Steady Amber) WAN port is successfully connected
Flashing Data is being sent or received.
Back Panel Connectors
Button/port Description
Button/port Description
Reset Reset configurations to default. Press the button and hold for 10
seconds.
1x, 2x, 3x, 4x LAN Ports. Connect LAN systems with RJ-45 cable.
WAN WAN port. Connect DSL or Cable modem.
PWR Power jack. Connect with AC power adapter.
1.4 System Requirements
● One or more PCs (desktop or notebook) with Ethernet interface.
● TCP/IP protocol must be installed on all PCs.
● Have valid Internet Access account and a DSL or cable modem.
● 10/100BaseT network cables with RJ-45 connectors.
● System with MS Internet Explorer ver. 6.0 or later.
1.5 Installation Instruction
1) Power off Broadband Router and DSL/cable modem.
2) Connect systems to the LAN ports on the Broadband Router with straight LAN cables.
3) Connect the DSL or cable modem to the WAN port on the Broadband Router.
4) Power on DSL or cable modem first, then connect power adapter to the power jack on the Broadband Router and
plug the power cable into an outlet.
5) Check LEDs.
a) Once power on the Broadband Router, Power LED should be on.
b) LAN LED should be on for each active LAN connection.
c) The WAN LED should be on when the DSL or cable modem is connected.
Warning: Only use the power adapter is provided from this package, use other power adapter may cause hardware
damage
2. PC Configuration ____
User needs to configure TCP/IP network settings, Internet access configuration for each system within the Broadband
Router’s LAN network. By default, the Broadbnad Router acts as a DHCP server for server version of Windows, it
automatically assigns IP address to each system when systems boot up. For all non-server version of Windows, the
default TCP/IP setting acts as a DHCP client. If user chooses fixed IP addresses for client systems, the Gateway of
the client system must be set to the IP address of the Broadband Router and DNS of the client system should be set to
the address provided by your ISP.
2.1 TCP/IP Networking
Checking TCP/IP Settings for Windows 2000
a) Select “Start Æ Control Panel Æ Network and Dial-up Connection” and right click “Local Area
Connection” then click “Properties”,
b) Select the “Internet Protocol (TCP/IP)” for the network card on your system, then click “Properties”, window
below will appear.
‧ If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”.
‧ If you decide to use the IP address you are desired, select “Use the following IP address”. Make sure
enter correct addresses in “IP Address” and “Subnet Mask” fields.
‧ You must set Wireless Router’s IP address as “Default Gateway”.
‧ If the DNS Server fields are empty, select “Use the following DNS server addresses” and enter the
DNS address is provided by your ISP, then click “OK”.
Checking TCP/IP Settings for Windows XP
a) Click “Start”, select “Control Panel Æ Network Connection” and right click “Local Area Connection” then
select “Properties”, window below will appear.
b) Select “Internet Protocol (TCP/IP)” then click “Properties”, window below will appear.
‧ If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”.
‧ If you decide to use the IP address you are desired, select “Use the following IP address”. Make sure
enter correct addresses in “IP Address” and “Subnet Mask” fields.
‧ You must set Wireless Router’s IP address as “Default Gateway”.
‧ If the DNS Server fields are empty, select “Use the following DNS server addresses” and enter the
DNS address is provided by your ISP, then click “OK”.
Checking TCP/IP Settings for Windows Vista
a) Click “Start” Æ “Control Panel Æ “Manage Network Connections” and right click “Local Area
Connection” then select “Properties”, window below will appear.
b) Select “Internet Protocol (TCP/IP)” then click “Properties”, window below will appear.
‧ If you decide to use IP address from Wireless Router, select “Obtain an IP address automatically”.
‧ If you decide to use the IP address you are desired, select “Use the following IP address”. Make sure
enter correct addresses in “IP Address” and “Subnet Mask” fields.
‧ You must set Wireless Router’s IP address as “Default Gateway”.
‧ If the DNS Server fields are empty, select “Use the following DNS server addresses” and enter the
DNS address is provided by your ISP, then click “OK”.
3. Setup Broadband Router Configurations via Web Browser
The Broadband Router comes with a web-based configuration utility. Users can access this configuration utility from
any of client system within Broadband Router’s LAN. For best results, either use Microsoft Internet Explorer 6.0 or
later.
Before you start configuring your Broadband Router, you have to get following information from your ISP:
a) Has your ISP assigned you a static IP address, or they will assign one to you dynamically? If you have received a
static IP address, what is it?
b) Does your ISP use PPPoE? If so, what is your PPPoE username and password?
If you are not sure of above questions, please contact your ISP.
3.1 Start your Web Browser
To use the Web-Based Utility, you have to launch your Internet Browser (MS IE 6.0 or later).
Step1: Enter Broadband Router default IP address http://192.168.2.1
in the Address field then hit Enter key:
Step2: Login dialog box will appear, enter admin as User Name and default password is 1234, then click “OK” to login
web-based utility.
3.2 Quick Setup
Quick Setup will help you setup the Broadband Router quickly. There have six types of WAN Connections: Dynamic IP
Address, Static IP, PPPoE, PPTP, L2TP, and BigPond.
When configure the Quick Setup wizard, you can setup Host Settings, such as Host name, Time Zone, and Daylight
Saving as below. Click “Next” to continue.
After specify the WAN connection type required by your ISP, please follow the next steps to configure DHCP and DNS
settings to complete the wizard.
Dynamic IP address: Obtain an IP address automatically from your service provider.
Static IP: Use Static IP address to access Network, your ISP will provide a static IP address.
PPPOE: PPPoE is a common connection type used for xDSL.
PPTP: PPP Tunneling Protocol can support multi-protocol Virtual Private Network (VPN)
L2TP: Layer 2 Tunneling Protocol can support multi-protocol Virtual Private Network (VPN)
BigPond: BigPond is an Australian internet service provider and is a subsidiary of Telstra.
3.3 Administrator
3.3.1 Management
Use this page to restrict management access based on a specific password. Passwords can contain from 4-12
alphanumeric characters, and are case sensitive.
Idle Time-out - The amount of time of inactivity before the Broadband Router will automatically close the Administrator
session. Set this to zero to disable it. Default is 300.
Remote Management - By default, management access is only available to users on your local network. However, you
can also manage the Broadband Router from a remote host by adding the IP address of an administrator to this screen.
Login Account: Allows you to setup a password in order to access the web-based management website.
Remote Management: You can specify a Host IP address that can perform remote management functions.
3.3.2 System Settings
The System Settings window configures broadband router basic settings, such as router’s Host Name, Set Time Zone,
Daylight Saving and Operation Mode.
NTP Server (IP or Domain Name): Enter a Domain Name if it was provided by the ISP
Time Zone: Select the time zone of the country you are currently in. The router will set its time based on your selection.
Daylight Saving: The router can also take Daylight savings into account. If you wish to use this function, you must
check/tick the enable box to enable your daylight saving configuration.
Host Name: Enter a hostname if it was provided by the ISP (Default: router).
NAPT: You can select to enable NAPT function.
3.3.3 Firmware Upgrade
User uses the Firmware Upgrade window to locate the new firmware then upgrade the system firmware. Click
Browse… to search for the new firmware location, and then click OK to precede the upgrade.
3.3.4 Configuration
Use this window to restore or backup broadband router settings, such as Restore Factory Default, Backup Settings and
Restore Settings. The Factory Default settings are: “Username
: admin”, “Password: 1234”, “IP: 192.168.2.1”,
“Natmask
: 255.255.255.0”
3.3.5 Tools
If for any reason the device is not responding correctly, you may want to restart the unit by clicking on the Reboot
button.
3.3.6 Language
Specify the language of the device menu. The two languages are supported in this router: English and Traditional
Chinese.
3.3.7 Log Settings
Not only does the device display the logs of activities and events, it can be setup to send these logs to another location.
The logs can be sent via email to a specific email account.
SMTP Server: The address of the SMTP (Simple Mail Transfer Protocol) server that will be used to send the logs.
Email Address: The email address the logs will be sent to. Click Email Log to send the email.
3.3.8 Logout
Click Logout in the task bar to initiate broadband router logout process.
3.4 WAN
Specify the WAN connection mode required by your Internet Service Provider, then click "OK" Button to provide
detailed configuration parameters for the selected connection type.
(a) Dynamic IP address
Select this option if your ISP provides you an IP address automatically. This option is typically used for Cable services.
Please enter the Dynamic IP information accordingly.
DHCP: Obtain an IP address automatically from the ISP.
MAC Address Clone: You can use the “Clone MAC Address” button to copy the MAC address of the Ethernet Card
installed by your ISP and replace the WAN MAC address with this MAC address.
(b) Static IP
The router’s IP address and Subnet Mask are as seen by external user on the Internet (including your ISP). If your
Internet connection requires a static IP address, then your ISP will provide you with a Static IP Address and Subnet
Mask.
IP address: IP address is given from your ISP.
Subnet Mask: Enter the subnet mask of the router.
Gateway Address: Enter the gateway address at ISP end.
MTU (576-1500): You can specify the maximum size of your transmission packet to the Internet. Leave it as it is if you
to not wish to set a maximum packet size.
Does ISP provide more IP address: If your ISP supports more IP addresses, please check it; otherwise, leave it
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
