Delta Children Rocking Bassinet Assembly Instructions

Brand: Delta Children

Model: Rocking Bassinet

Category: Baby furniture

Type: Assembly Instructions

This manual is also suitable for

Made in China

Bassinet

Assembly Instructions

Model Number

Manufacturer’s Code

If you have missing parts or questions...

If a part is missing or you have questions, call us. DO NOT return

product parts to store from where it was purchased before calling us at:

(212) 645-9033

Our service is fast, free and easier than returning the product.

Important: So we can better assist you, have the model number and

manufacturer’s code available. It is located at bottom right-hand corner of this page.

Before assembly, read these instructions. Make sure all pre-assembled parts are tight.

Store this instruction manual for future reference.

Adult assembly required.

Delta Children’s Products, Inc.

114 West 26th Street

New York, NY 10001 (USA)

Web site: www.DeltaChildrensProducts.com

E-mail: [email protected]

Customer Service Toll-Free: (212) 645-9033

DeltaTM

Childrens’s Products

DeltaTM

Childrens’s Products

Your Delta Baby Gear is warranted to be free from defects for a

period of 30 days from the date of purchase under normal use.

This warranty extends only to the original retail purchaser and is

only valid when supplied with proof of purchase, or if received

as a gift, when the registration is on ﬁle with Delta.

Warranty

35301-310

04 / 2011

Disassembling Bassinet for Storage

To disassemble Bassinet for storage, follow assembly steps in reverse.

Store all parts and hardware together in a safe place. Store the instruction manual for future

reference.

Fabric:

DO NOT USE THIS PRODUCT WITHOUT FABRIC ASSEMBLY IN PLACE. Fabric Assembly may be

removed for washing. Always follow instructions for disassembly and reassembly. Fabric assembly

may be hand-washed in mild detergent. Never use bleach. Air dry or use dryer on the lowest

setting. Use iron for touch up on fabric for best results. Please note that the Canopy fabric cannot be

removed from Canopy frame, and may be hand-washed.

Frame:

Frame paint may be touched up as needed. Use only non-toxic paints approved for children’s

products. Check all frame fasteners occasionally. Tighten all screws and bolts as necessary.

Cleaning and Maintenance

To install batteries: First unscrew the battery cover and install 3 C batteries as shown in the

battery compartment.

To install batteries: First unscrew the battery cover and install 3 AAA batteries for Remote

Controller.

SAFE BATTERY USE

• Keep batteries out of the reach of children.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.

• Do not mix different battery types.

• Make sure batteries are inserted correctly.

• Discard leaky batteries immediately. When discarding batteries, be sure to dispose of them in

the proper manner, according to your state and local regulations.

Battery Power Pack and Remote Controller

WARNING -

BASSINET WARNINGS

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR

FUTURE USE.

• Before each usage or assembly, inspect unit for damaged hardware, loose joints, missing parts or

sharp edges. NEVER use this product if there are any loose or missing fasteners, loose joints,

broken parts, or torn mesh/fabric. Check before assembly and periodically during use. Contact

Delta Children’s Product Customer Service Department at 212-645-9033 (8:00am ~ 4:30pm

EST) for replacement parts, repair or instructions. DO NOT substitute parts.

• FALL HAZARD – To help prevent falls, DO NOT use this product when the infant begins to push

up on hands and knees or has reached manufacturer’s recommended maximum weight of 15 lbs.

• Use bassinet with only one child at a time.

• Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as

hood strings or paciﬁer cords. DO NOT suspend strings over a crib or attach strings to toys.

SUFFOCATION HAZARD:

Infants can suffocate:

• In gaps between an extra pad and side of the bassinet/cradle.

• On soft bedding.

NEVER add a mattress, pillow, comforter or padding. Use ONLY the pad provided by the

manufacturer.

intended for that purpose. They can cause suffocation.

• To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their

backs to sleep, unless otherwise advised by your physician.

• If a sheet is used with the pad, use only the one provided by the manufacturer or one

speciﬁcally designed to ﬁt the dimensions of the bassinet/cradle.

• The total thickness of the mattress should not exceed 1 1/2 in. and the length and width

should not allow a gap greater then 1 in. between the mattress and the side of the

bassinet when the mattress is pushed up against the sides and into one corner of the unit.

• DO NOT leave child unattended in the bassinet with the wheels on the bassinet frame in

the “up” position.

• DO NOT place bassinet near a window where cords from blinds or drapes may strangle a

child. Child may fall out of window. DO NOT place cords, straps or similar items that could

become wound around a child’s neck in or near the bassinet.

• CAUTION: Check proper ﬁt of mattress. Mattress should not be more than 1 1/2 in. thick.

The maximum gap between mattress and inside of the bassinet border (or edge) should

be no more than 1 in.

Failure to follow these warnings and assembly instructions

could result in serious injury or death.

WARNINGS

NOTES

WARNINGS

MOBILE WARNINGS

Read all Instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR

FUTURE USE.

• A mobile is intended for visual stimulation and is not intended to be grasped by the child.

• From birth to 5 months.

• Possible entanglement injury.

• Keep out of baby’s reach.

• Remove mobile from bassinet or cradle when baby begins to push up on hands and knees. Toys

are not meant to be “mouthed” by the baby and should be positioned clearly out of reach of the

baby’s face and mouth.

• Adult assembly required.

• Always attach all provided fasteners (strings, straps, clamps, etc.) tightly to the bassinet according

to the instructions. Check frequently. Do not add additional strings or straps to attach to the

bassinet.

• The mobile is not intended for use in playpens or portable cribs.

WARNING

Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR

FUTURE USE.

• Do not use changing table if it is damaged or broken.

• Maximum weight of child: 25 lbs. (11.34 kg).

• Never leave child unattended.

CHANGING TABLE WARNINGS

WARNING -

Failure to follow these warnings and assembly instructions

could result in serious injury or death.

WARNING -

FALL HAZARD – To prevent death or serious injury, always keep

child within arm’s reach.

Notes

FREQUENTLY ASKED QUESTIONS

00095 - Mattress

Pad

(x1)

Parts and Part Numbers

00084 - Accessory

Basket

(x1)

00066 - Accessory

Basket Tubes

(x2)

00065 - Non-Locking

Rocker Base

(x1)

00068 - Rocker

Legs

(x4)

02503 - Support

Tube

(x2)

00135 - Bassinet

Frame

(x1)

00131 - Mattress

Support

(x1)

01630 - Mobile

Arm

(x1) *Screws included

00083 - Bassinet

Fabric Skirt

(x1)

DO NOT REMOVE FOAM FROM BASSINET PARTS

00064 - Locking

Rocker Base

(x1)

PARTS AND PART NUMBERS

00560 - Sheet (x1)

00073 - Canopy (x1)

Frequently Asked Questions - continued

7) Batteries

- Bassinets require 3 “C” batteries.

- If your bassinet includes a remote control, the remote control requires 3 “AAA” batteries.

8) Electronics Trouble-Shooting

Double-check that all batteries are installed correctly in the battery box. Also check that the wire is

properly attached to the battery box and to the mobile base.

9) Cleaning your bassinet

To clean bassinet use a damp cloth or sponge with household soap or detergent and wipe clean the vinyl,

plastic, and metal parts. The sheet is machine washable and recommended to drip dry. Do not use bleach.

Battery Box

Underside of the

wooden mattress support

Battery

Box

Wire

Parts & Hardware/Part & Hardware Numbers

HARDWARE SHOWN AT ACTUAL SIZE

00079 - Wrench

00078 - Screwdriver

00077 - Rocker Leg Screw (x8)

00139 - Mattress Support

Screw

(x2)

00130 - Lock Nuts

(x4)

00142 - Mobile

Remote Control

(x1)

*On certain models

01629 - Mobile

Propeller with Toys

(x1)

*Toys may vary

*Mobile cover on certain models

PARTS & HARDWARE/PART & HARDWARE NUMBERS

FREQUENTLY ASKED QUESTIONS

Frequently Asked Questions

1) Warranty Information

All Delta bassinets include a 30-day limited warranty. Please ﬁll out the product registration card that

accompanied your bassinet, and mail it back to us so we can have your information on ﬁle.

2) Model Number and Manufacturer’s Code

It is important to have the model number and manufacturer’s code available when calling our Customer

of base assembly.

3) Height Adjustment

The 5 positions for the height-adjustable legs are: 30.25” (lowest), 32.25” , 34.00” , 35.75” , and 37.50”

(highest).

4) Weight Limits

- Bassinet weight limit: 15lbs

- Changing table weight limit: 25lbs

5) Mattress Pad Dimensions

are 32” x 15.75”.

6) Mattress Pad Thickness

It is important to use only the mattress pad provided by the manufacturer. According to ASTM (American

Society For Testing and Materials) standards, the total thickness of the mattress should not exceed 1.5”. The

length and width should not allow a gap greater than 1” between the mattress and the side of the bassinet

when the mattress is pushed up against the sides and into one corner of the unit. Replacement mattresses

are available through Customer Service.

37.5 inches (highest position)

30.25 inches (lowest position)

00080 - Lock Nuts

(x2)

The mattress pad dimensions

DELTA CHILDREN’S PRODUCTS

114 WEST 26TH STREET. NEW YORK, NY 10001 USA

TEL.: 212-645-9033 STYLE NO.:

MADE IN CHINA ORDER NO.:

FABRIQUÉ EN CHINE

DATE OF MFG.:

35301- 310

250063

04/ 2011

LOT NO.: WF08006

Service department. This information can be found on a white sticker on the underside of support tube

Bassinet Base Assembly

Continue to Step 2...

Insert two (2) Accessory Basket Tubes (B)

into the Non-Locking Rocker Base (cc).

00066 - Accessory

Basket Tubes

(x2)

00065 - Non-Locking

Rocker Base

(x1)

Parts Needed:

BASSINET BASE ASSEMBLY

MOBILE OPERATION

Mobile Operation

Night Light - activates the mobile light. Press to turn on mobile light for 5-minutes. To turn off sooner

than 5-minutes, press again. Press the button again to start another 5 minute cycle. This operating cycle is

the same for all functions except music.

Vibration - Press to start 5-minute cycle, press again to stop. The strength of vibration is adjusted with

the round knob on the side of the mobile arm. This adjustment knob is also marked with waves. Turning

towards the + sign increases vibration, towards the - sign reduces vibration.

Music - operates the music function . Press the button successive times to cycle the music through two

modes of music, one of musical chimes, and back to off. Music volume is adjusted with the “Music Volume

Adjustment” button on the other side of the mobile arm. Turning towards the + sign increases volume,

towards the - sign reduces volume.

Small Lights - operates the light show. Press to start the 5-minute show. Press again to stop the music. If

the music button is pressed during a light show, the show will restart, synchronized with the music.

Rotate Mobile Toys - controls the mobile. Press to begin a 5-minute cycle. Press again to stop the mobil

Press again to start a new 5-minute cycle. If the mobile button is pressed while the mobile is operating, the

mobile cycle will restart, synchronized with the music.

After batteries are in place, turn on “Mobile Function” switch at base of mobile arm. This is the main power

switch to the arm and also turns on the power LED on the “Night Light” button. This LED will stay lit to help

you ﬁnd the “Night Light” button in the dark.

Rotate Mobile Toys

Small Lights

Music

Vibration

Night Light

Music Volume

Adjustment

Vibration

Adjustment

Mobile Functions

On/Off

Mobile Remote

requires

3 AAA batteries.

*on certain models

Bassinet Base Assembly - continued

Continue to Step 3...

00068 - Rocker

Legs

(x2)

HARDWARE SHOWN

AT ACTUAL SIZE

00077 - Rocker Leg

Screw

(x2)

00078 - Screwdriver

00084 - Accessory

Basket

(x1)

Figure 1

Parts Needed:

Insert two (2) Rocker Legs (D) into Non-

Locking Rocker Base. Secure using two

(2) Rocker Leg Screws (M) (see Figure

1). The screws will go through the Non-

Locking Rocker Base, Rocker Legs, and

into the Accessory Basket Tubes. Then

slide on the Accessory Basket (A) onto

the Accessory Basket Tubes.

Note: Snap button holes on Rocker Legs

must face towards the inside.

BASSINET BASE ASSEMBLY

CASTER ASSEMBLY

Continue to Step 19...

Caster Assembly

Parts Needed:

To Lower Casters:

To Raise Casters:

Rotate In

Pull Down

Bassinet Base Assembly - continued

Continue to Step 4...

On other side of assembly, attach Rocker

Legs (D) into Locking Rocker Base (C).

Then attach Locking Rocker Base to

Accessory Basket Tubes. Secure using

two (2) Rocker Leg Screws (M). The

screws will go through the Locking

Rocker Base, Rocker Legs and into the

Accessory Basket Tubes (see Figure 1).

Note: Snap button holes on Rocker Legs

must face towards the inside.

00078 - Screwdriver

HARDWARE SHOWN

AT ACTUAL SIZE

00068 - Rocker

Legs

(x2)

00077 - Rocker Leg

Screw

(x2)

Figure 1

00064 - Locking

Rocker Base

(x1)

Parts Needed:

BASSINET BASE ASSEMBLY

CHANGER ASSEMBLY

Continue to Step 18...

Changer Assembly

Parts Needed:

Place the Bassinet against a wall and lock

the two (2) Locking Rocker Base caster

wheels (see Figure 1). This will keep the

Bassinet in a stationary position.

Figure 1

Bassinet Base Assembly - continued

Continue to Step 5...

Tie Fabric Accessory Basket (A) to the

four (4) Rocker Legs (D).

Parts Needed:

BASSINET BASE ASSEMBLY

BASSINET BASKET ASSEMBLY

Bassinet Basket Assembly - continued

Continue to Step 17...

Parts Needed:

01629 - Mobile Assembly (x1)

Figure 1

Attach Mobile Assembly (T) to the

Mobile Arm (K) by lining up the top of

the Mobile Assembly to the connector

located on the Mobile Arm and push

ﬁrmly up until it snaps into place

(see Figure 1).

Connector

Bassinet Base Assembly - continued

Continue to Step 6...

Insert Support Tube (E) into Rocker Legs

(D). Push in on the snap button. Then

slide the Support Tube down until the

snap button locks into place.

Note: Make sure holes on Support Tubes

face in.

02503 - Support

Tube

(x1)

Parts Needed:

BASSINET BASE ASSEMBLY

BASSINET BASKET ASSEMBLY

Continue to Step 16...

Parts Needed:

Bassinet Basket Assembly - continued

Insert the two ends of the Canopy (S)

through the openings in the Bassinet

Fabric and into the connectors on the

Bassinet Basket Frame. Push down until

both sides snap into place (see Figure 1).

Then locate the two snaps on the Canopy

(near the connectors ). Snap into place (see

Figure 1). Attach the velcro or snap at the

back of the Canopy to the bassinet skirt

(see Figure 2 & 2a).

Figure 2

Figure 1

00073 - Canopy (x1)

Snap

Button

Figure 2a

Bassinet Base Assembly - continued

Continue to Step 7...

IMPORTANT: Height of Support

Tubes must be adjusted evenly. Do

Not elevate one side higher than

the other.

02503 - Support

Tube

(x1)

Note: When both Support Tubes (E)

are in place, you may adjust the height

by pushing in on the snap buttons and

lifting up or down.

Parts Needed:

Insert Support Tube (E) into Rocker Legs

(D). Push in on the snap button. Then

slide the Support Tube down until the

snap button locks into place.

BASSINET BASE ASSEMBLY

BASSINET BASKET ASSEMBLY

Bassinet Basket Assembly - continued

Continue to Step 15...

Parts Needed:

Slip the Sheet (R) over the Mattress Pad (Q).

Then Assemble it into the bottom of the

Bassinet Assembly (see Figure 1).

Note: On some models sheet will already

be attached to mattress pad.

00095 - Mattress

Pad

(x1)

00560 - Sheet (x1)

Figure 1

Bassinet Basket Frame Assembly

Continue to Step 8...

Parts Needed:

BASSINET BASKET FRAME ASSEMBLY

BASSINET BASKET ASSEMBLY

Attach the Bassinet Frame (H) to the

Bassinet Base Assembly with four (4)

Rocker Leg/Basket Frame Screws (M)

and four (4) Lock Nuts (Z).

00077 - Rocker Leg Screw

(x4)

00130 - Lock Nuts

(x4)

HARDWARE SHOWN

AT ACTUAL SIZE

00079 - Wrench

00078 - Screwdriver

00135 - Bassinet

Frame

(x1)

Bassinet Basket Assembly - continued

Continue to Step 14...

Parts Needed:

Find the elastic red pockets on the

bottom of both ends of Bassinet Fabric

Skirt (L). Pull them underneath the

wooden Mattress Support. Refasten all 10

(see Figure 1). Also you will need to fasten

4 snaps that attach skirt to Mattress

Support (see Figure 2). Then loop the

Mobile Arm wire and battery wire through

side tabs and connect both ends together

(see Figure 3).

Figure 1

Figure 2

Figure 3

Snap

Red Pocket

Mattress

Support

snaps that go around the skirt

Bassinet Basket Frame Assembly - continued

Continue to Step 9...

Parts Needed:

BASSINET BASKET FRAME ASSEMBLY

BASSINET BASKET ASSEMBLY

Locate the battery compartment. With the

Screwdriver, remove battery cover plate

and install three (3) “C” alkaline batteries

(see Figure 1). Replace the cover plate and

tighten the screws.

Note: We recommend using alkaline

batteries for longer battery life. Make sure

batteries are correctly installed.

Battery

Compartment

Figure 1

00131 - Mattress

Support

(x1)

Bassinet Basket Assembly - continued

Continue to Step 13...

Parts Needed:

Note: Unfasten 10 snaps around

the Bassinet Fabric Skirt (L)

(see Figure 1).

Find the opening for the Mobile Arm,

and two openings for the Canopy. Make

sure that they will line up. Then Slide

the Bassinet Fabric Skirt (L) over the

Mobile Arm and shape it around the

Bassinet Basket Frame. Make sure fabric

ﬁts snugly around the top bar of the

Bassinet Basket Frame.

00083 - Bassinet

Fabric Skirt

(x1)

Figure 1

Snap

Bassinet Basket Frame Assembly - continued

Continue to Step 10...

Attach Mattress Support (I) to Bassinet

Frame (H) using four (2) Mattress Support

see

Figure 1). Tighten the screws and nuts by

using the Screwdriver and the Wrench.

Make sure vibration battery unit is on the

bottom.

Note: DO NOT remove foam from

around Bassinet Frame.

00079 - Wrench

00078 - Screwdriver00131 - Mattress

Support

(x1)

00139 - Mattress

Support Screw

(x2)

00080 - Lock Nuts

(x2)

HARDWARE SHOWN

AT ACTUAL SIZE

Figure 1

Parts Needed:

BASSINET BASKET FRAME ASSEMBLY

BASSINET BASKET ASSEMBLY

Bassinet Basket Assembly - continued

Continue to Step 11...

Parts Needed:

01630 - Mobile

Arm

(x1) *screws included

00078 - Screwdriver

Remove two (2) pre-installed screws from

Mobile Arm (K) (see Figure 1). Locate the

pre-drilled holes on the Bassinet Frame

and snap on Mobile Arm (K) (see Figure 2).

Re-insert the screws into the Mobile Arm.

Tighten with Screwdriver.

Figure 2

Figure 1

Screw

Screws (U) and four (2) Lock Nuts (

Delta Children Rocking Bassinet Assembly Instructions

Brand: Delta Children

Model: Rocking Bassinet

Category: Baby furniture

Type: Assembly Instructions

This manual is also suitable for

Download PDF

report

Delta Children Rocking Bassinet Assembly Instructions

This manual is also suitable for

Delta Children Rocking Bassinet Assembly Instructions

Related papers

Other documents