2. Computers & electronics
  3. Projectors
  4. Projector mounts
  5. Vivitek
  6. DH758UST
DH758UST

Vivitek DH758UST Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Vivitek DH758UST Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Model:WM-3
Installation Manual
It is imperative that the installation instructions within this manual are followed for ●
safety reasons. Vivitek Corporation is not responsible for damages resulting from
incorrectly installed mounts or projectors on to the mount.
Sufcient expertise is required for installing this projector wall mount.●
Do not use the projector wall mount for purposes other than for which it is designed.●
Please contact Vivitek at 1-855-885-2378 with any questions pertaining to the correct ●
installation of this projector mount.
46101 FREMONT BLVD, FREMONT, CA. 94538 - TEL 855.885.2378 - EMAIL: - WWW.VIVITEKUSA.COMPROAV@VIVITEKCORP.COM
Important Safety
Checking The Supplied Accessories
*
Wall Plate X 1
Fixed Support Arm X 1
Wall Cover X 1
Projector Mounting
Plate X 1
B
NO
C
D
E
A
5
5
1
3
F
Screw(M6X55)
Φ10mm Anchor bolt
L5 Allen key
4
Screw(M4X10)
diagrammatic
presentation
designation
quantity
1
L3 Allen key
Screw(M6X15)
Wall Plate Cover X 1
2
3
4
5
7
8
9
Pg.2
G
M4 connecting
screw
3
To Set The Projector Wall Mount On The Wall
WM-3
Projector
Resolution
Screen Size
(Diagonal)
V-Offset
(Distance between bottom of wall plate to top of image)
Note: V-Offset (WXGA) can be calculated for different screen size = [screen width/2 (0.351)]
94” (80” x 50”) 14”
1080P
(1920x1080)
Screen Size
(Diagonal)
V-Offset
(Distance between bottom of wall plate to top of image)
94” (82” x 46”) 13.375”
Note: V-Offset (1080P) can be calculated for different screen size = [screen width/2 (0.327)]
Checking The Installation Position
Projection screen
V-Offset
Wall plate
Projection screen
Bottom of
mounting plate
Top of image
V-Offset
Wall plate must be aligned to center of screen
Pg.3
100” (85” x 53”)
14.9”
87” (74” x 46”) 13”
Projector
Resolution
110” (95” x 53”) 15.5”
100” (87” x 49”) 14.25”
92” (80” x 45”) 13.125”
87” (76” x 43”) 12.5”
WXGA
(1280x800)
● The bracket is suitable for concrete wall mounting or wooden stud wall.
● Concrete wall mounting thickness must be a minimum 4'' (100mm). Anchor bolt and screw (M6 × 55) are
needed to be used for concrete wall installation.
● Dry-wall wall thickness must be a minimum 4.5" (114mm). Only screw(M6 × 55) is needed to be used for
installation, and gypsum board thickness less than 0.59" (15mm).
If the wall is not strong enough, reinforce it sufficiently before installation.
● Please contact reseller if you have any questions
about mounting surface issue.
>55mm
ø10~11mm
B
Concrete wall mounting
Use anchor bolt
>55mm
ø3mm
Dry-wall mounting
Not use anchor bolt
When installation on the
wood stud wall, Align the
center of the wall mount
plate with the center of
the stud.
screw central point
Loosen the screws with L3 allen wrench,
pull out the support arm around 4'' (100mm)
and make power cable & signal cables go
through the support arm.
The cables can be got through the wall plate
by three ways as shown in the pictures. Then,
Lock the screw “F” , but not tighten it.
screw (M6 × 55) are needed
for installation in concrete wall mounting
screw (M6 × 55) are needed
for installation in dry-wall mounting
Pg.4
C
A
C
A
Take off the cap
Loosen the screw
D
C
F
The arrows up
The arrows up
The cables
The cables
The cables
To Install The Projector On The Projector Wall Mount
A
A
B
B
Screen Adjustment Direction
● You can adjust the projector upward/
-downward according to your need.
● Tighten the screw “F” after locating
the projector position.
C
F
A
B
● Move the projector mounting plate leftwards/rightwards to determine the projector position.
Leftward/Rightward
sliding distance
Pg.5
E
G
If the surface is not at,
pls use the “G” to avoid
interference.
Sliding distance of
adjusting the projector
upward/downward:
3.15''(80mm)
/