Belden HIRSCHMANN BRS40 User manual

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Industrial Ethernet BOBCAT Rail Switch

BRS20/22/30/32/40/42/50/52

3/12/20

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

3

Contents

Safety instructions 6

About this manual 15

Key 16

1 Description 17

1.1 General device description 17

1.2 Device name and product code 18

1.3 Device views 22

1.3.1 Front view 22

1.3.2 Rear view 24

1.4 Power supply 25

1.4.1 Supply voltage with characteristic value T 25

1.4.2 Supply voltage with characteristic value F 25

1.4.3 Supply voltage with characteristic value U 25

1.4.4 Supply voltage with characteristic value P 25

1.5 Ethernet ports 26

1.5.1 10/100 Mbit/s twisted pair port 26

1.5.2 10/100/1000 Mbit/s twisted pair port 26

1.5.3 100 Mbit/s F/O port 27

1.5.4 100/1000 Mbit/s F/O port 28

1.5.5 100/1000/2500 Mbit/s F/O port 28

1.5.6 Support of PoE(+) 29

1.6 Display elements 30

1.6.1 Device state 30

1.6.2 Port status 31

1.7 Management interfaces 33

1.7.1 Signal contact 33

1.7.2 USB-C interface 34

1.7.3 Digital input 35

2 Installation 37

2.1 Checking the package contents 37

2.2 Installing and grounding the device 37

4

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

2.2.1 Installing the device onto the DIN rail 37

2.2.2 Grounding the device 39

2.2.3 Connecting the ferrite (optional) 39

2.3 Installing an SFP transceiver (optional) 40

2.4 Connecting the terminal blocks 41

2.4.1 Power supply 41

2.4.2 Signal contact (optional) 44

2.4.3 Digital input (optional) 45

2.5 Operating the device 46

2.6 Connecting data cables 47

2.7 Filling out the inscription label 47

3 Making basic settings 48

3.1 First login (Password change) 49

4 Monitoring the ambient air temperature 50

5 Maintenance and service 51

6Disassembly 52

6.1 Removing an SFP transceiver (optional) 52

6.2 Removing the device 53

7 Technical data 54

7.1 General data 54

7.2 Supply voltage 55

7.3 Power consumption/power output 57

7.4 Signal contact 58

7.5 Digital input 59

7.6 Climatic conditions during operation 60

7.7 Climatic conditions during storage 61

7.8 Casing widths for PoE device variants 61

7.9 Dimension drawings 62

7.9.1 Device variants with casing with characteristic

value C (plastic casing) 62

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

5

7.9.2 Device variants with casing with characteristic

value E/D (metal casing) 65

7.10 Immunity 68

7.11 Electromagnetic compatibility (EMC) 68

7.12 Network range 70

7.12.1 10/100/1000 Mbit/s twisted pair port 70

7.12.2 Fast Ethernet SFP transceiver 70

7.12.3 Gigabit Ethernet SFP transceiver 72

7.12.4 2.5 Gigabit Ethernet SFP transceiver 74

7.12.5 Bidirectional Fast Ethernet SFP transceiver 75

7.12.6 Bidirectional Gigabit Ethernet SFP transceiver 75

7.13 De-rating due to SFP transceiver 76

7.13.1 Fast Ethernet SFP transceiver 76

7.13.2 Gigabit Ethernet SFP transceiver 77

7.13.3 2.5 Gigabit Ethernet SFP transceiver 78

7.13.4 Bidirectional Fast Ethernet SFP transceiver 79

7.13.5 Bidirectional Gigabit Ethernet SFP transceiver 79

8 Scope of delivery 80

9 Accessories 81

9.1 General accessories 81

9.2 Order numbers for standard variants 81

9.3 Fast Ethernet SFP transceiver 82

9.4 Gigabit Ethernet SFP transceiver 82

9.5 2.5 Gigabit Ethernet SFP transceiver 83

9.6 Bidirectional Fast Ethernet SFP transceiver 83

9.7 Bidirectional Gigabit Ethernet SFP transceiver 83

10 Underlying technical standards 85

A Further support 86

6

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

Safety instructions

 General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

 Before connecting any cable, read this document, and the safety

instructions and warnings.

 Operate the device with undamaged components exclusively.

 The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

 Certified usage

 Use the product only for the application cases described in the

Hirschmann product information, including this manual.

 Operate the product only according to the technical specifications.

See “Technical data” on page 54.

 Connect to the product only components suitable for the requirements

of the specific application case.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow this instruction can result in death, serious injury, or

equipment damage.

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

7

 Installation site requirements

 Install this device only in a switch cabinet or in an operating site with

restricted access, to which maintenance staff have exclusive access.

 When you are selecting the installation location, make sure you

observe the climatic threshold values specified in the technical data.

 Use the device in an environment with a maximum pollution degree

that complies with the specifications in the technical data.

See “Technical data” on page 54.

 Qualification requirements for personnel

 Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

 Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

 Qualified personnel are aware of the dangers that exist in their work.

 Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

 Qualified personnel receive training on a regular basis.

 Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

 Shielding ground

The shielding ground of the connectable twisted pair cables is connected

to the ground connection as a conductor.

 Beware of possible short circuits when connecting a cable section with

conductive shielding braiding.

WARNING

FIRE HAZARD

Install the device in a fire enclosure as per EN 62368-1 or EN 60950-1 if you

are connecting it to a power supply >100 W (PS3) or >NEC Class 2.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

8

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

 Grounding the device

The device is grounded via the separate ground screw. The grounding

screw is located on the front right side of the device for narrow casing

sizes. For the medium and wide casing sizes, the grounding screw is

located at the bottom left of the front side of the device.

See “Dimension drawings” on page 62.

 Ground the device before connecting any other cables.

 Disconnect the grounding only after disconnecting all other cables.

 Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

 Requirements for connecting the signal contact

Before connecting the signal contact, always verify that the requirements

listed are complied with.

 Requirements for connecting the supply voltage

Before connecting the supply voltage, always verify that the requirements

listed are complied with.

The following requirements apply without restrictions:

 The electrical wires are voltage-free.

 The cables used are permitted for the temperature range of the application case.

Only use power supply cables that are suitable for a temperature 20 K higher

than the maximum ambient air temperature at which the device is used.

Only use copper wire.

The following requirements apply without restrictions:

 The connected voltage complies with the requirements for a safety extra-low voltage

(SELV) or ES1 as per IEC/EN 62368-1.

 The connected voltage is limited by a current limitation device or a fuse.

Observe the electrical threshold values for the signal contact.

See “Technical data” on page 54.

Prerequisites:

All of the following requirements are complied with:

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

9

Note: The devices can be supplied either via one voltage input or

redundantly via both voltage inputs.

 Supply voltage

The supply voltage is connected to the device casing through protective

elements exclusively.

 LED or laser components

LED or LASER components according to IEC 60825-1 (2014):

CLASS 1 LASER PRODUCT

CLASS 1 LED PRODUCT

 The supply voltage corresponds to the voltage specified on the type plate of the device.

 The power supply complies with the requirements for a safety extra-low voltage (SELV) or

ES1 as per IEC/EN 62368-1.

 The power supply has an easily accessible disconnecting device (for example a switch or

a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is

clear which disconnecting device belongs to which power supply cable.

 The wire diameter of the power supply cable is at least 0.75 mm² (North America: AWG18)

on the supply voltage input.

The wire diameter of the power supply cable is at least 1 mm² (North America: AWG16) on

the supply voltage input for PoE device variants.

 The cross-section of the ground conductor is the same size as or bigger than the cross-

section of the power supply cables.

Depending on the voltage input used (characteristic value F, T, U, P) and the supply voltage

used (DC, AC), the following additional requirements apply:

Device variants

featuring supply

voltage with

characteristic

value F, T, U

All of the following requirements are complied with:

Supply with DC voltage:

 There are fuses suitable for DC voltage in the positive conductors of

the supply lines, or the voltage sources are appropriately current-

limited. Regarding the properties of this fuse: See “Technical data”

on page 54.

 The negative conductors of the voltage inputs are on ground

potential.

Device variants

featuring supply

voltage with

characteristic value F

All of the following requirements are complied with:

Supply with AC voltage:

 There are fuses in the supply lines, or the voltage sources are

appropriately current-limited. Regarding the properties of this fuse:

See “Technical data” on page 54.

 The power sources are electrically isolated from the ground

potential.

Device variants

featuring supply

voltage with

characteristic value P

All of the following requirements are complied with:

 There are fuses suitable for DC voltage in the positive conductors of

the supply lines, or the voltage sources are appropriately current-

limited. Regarding the properties of this fuse: See “Technical data”

on page 54.

 The power sources are electrically isolated from the ground

potential. According to specification IEEE 802.3, the insulation

voltage must be 1500 V AC or 2250 V DC.

Prerequisites:

10

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

 National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

 Relevant for use in explosion hazard areas (Hazardous

Locations, Class I, Division 2)

This equipment is exclusively suitable for use in Class I, Division 2,

Groups A, B, C, and D or non-hazardous locations.

This device is an open-type device that is to be installed in an enclosure

suitable for the environment and accessible exclusively with the use of a

tool.

Exclusively use the device for the application cases specified by the

manufacturer. Failure to follow these instructions can impair device

protection.

WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT UNLESS

POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.

Avertissement - Risque d'explosion - Ne pas débrancher tant que le circuit est sous tension à

moins que l'emplacement soit connu pour ne contenir aucune concentration de gaz

inflammable.

WARNING - EXPLOSION HAZARD - SUBSTITUTION OF ANY COMPONENT MAY IMPAIR

SUITABILITY FOR CLASS I, DIVISION 2.

Avertissement - Risque d'explosion - La substitution de tout composant peut rendre ce

matériel incompatible pour une utilisation en classe I, division 2.

The storage medium ACA22-USB-C (EEC) is mechanically secured to prevent the connection

from being disconnected.

Le dispositif de sauvegarde ACA22-USB-C (EEC)est fixé mécaniquement pour éviter toute

déconnexion de la connexion.

A USB cable for configuring the device may only be used in a non-explosive area.

Un câble USB pour la configuration de l'équipement ne doit être utilisé que dans une zone non

explosive.

WARNING!

Connection or disconnection in an explosive atmosphere could result in an explosion.

AVERTISSEMENT!

Le branchement ou le débranchement dans une atmosphère explosive peut entraîner une

explosion.

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

11

Control Drawing for BRS devices according to Class I, Division 2 Hazardous Locations

Rev.: 3 Document No.: 000217023DNR Page 1/2

Ordinary Location,

Non-Hazardous Area,

Non-Explosive Atmosphere

Explosive Atmosphere

Class I, Division 2, Groups A, B,

C, D, T4

(**)

Hazardous Location

BRS - Industrial Ethernet

BOBCAT Rail Switch

(**) Temperature Code: T4

Ambient Temperature rating:

Ta: 0 °C to +60 °C for “S“ or “C“ temperature types

7Dí&WR&IRU³7³RU³(³WHPSHUDWXUHW\SHV

(Refer to the type designation on the device.)

(*) Associated apparatus:

7KHQRQLQFHQGLYH¿HOGZLULQJFLUFXLWFRQFHSWDOORZVLQWHUFRQQHFWLRQ

RIQRQLQFHQGLYH¿HOGZLULQJDSSDUDWXVDQGDVVRFLDWHGQRQLQFHQGLYH

¿HOGZLULQJDSSDUDWXVXVLQJDQ\RIWKHZLULQJPHWKRGVSHUPLWWHGIRU

XQFODVVL¿HGORFDWLRQVZKHQFHUWDLQSDUDPHWULFFRQGLWLRQVDUHPHW

Capacity: C

a

&

i

+ C

Cable

; Inductivity: L

a

/

i

+ L

Cable

The ACA22-USB-C (EEC) storage medium is mechanically secured

to prevent disconnection.

$86%FDEOHIRUFRQ¿JXUDWLRQWKHGHYLFHPD\H[FOXVLYHO\EHXVHGLQ

non-hazardous locations.

WARNING!

&RQQHFWLRQRUGLVFRQQHFWLRQLQDQH[SORVLYHDWPRVSKHUH

FRXOGUHVXOWLQDQH[SORVLRQ

7KHPD[LPXPFDEOHOHQJWKKDVWREHGHWHUPLQHGDVIROORZV

DPD[FDEOHOHQJWK< (L

a

í/

i

) / Cable

L

(“Cable

L

“ denotes the inductance per unit length of used cable)

and

EPD[FDEOHOHQJWK< (C

a

í&

i

) / Cable

C

(“Cable

C

“ denotes the capacitance per unit length of used cable)

The lower value of (a) and (b) is to apply.

Relay contacts:

(TXLSPHQWZLWKQRQLQFHQGLYH¿HOGZLULQJSDUDPHWHUV

Polarity is not relevant.

The relay terminals are dependent upon the following entity parame-

ters

(*)

:

9PD[ ,PD[ C

i

L

i

30 V 90 mA

2 nF

1 μH

USB

Relay

The earth conductor

must be at least

the same wire size

(mm² or AWG) as the

supply conductors of

the supply voltage.

12

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

Control Drawing for BRS devices according to Class I, Division 2 Hazardous Locations

Rev.: 3 Document No.: 000217023DNR Page 2/2

For use in Hazardous Locations Class I, Division 2, Groups A, B, C, D:

([FOXVLYHO\DOORZHGIRU%56PRGHO1RVZKLFKDUHLQGLYLGXDOO\ODEHOHG

“FOR USE IN HAZARDOUS LOCATIONS“.

7KLVHTXLSPHQWLVH[FOXVLYHO\VXLWDEOHIRUXVHLQ&ODVV,'LYLVLRQ*URXSV$%&DQG'RUQRQKD]DUGRXV

locations.

1RQLQFHQGLYH¿HOGZLULQJFLUFXLWVPXVWEHZLUHGLQDFFRUGDQFHZLWKWKH1DWLRQDO(OHFWULFDO&RGH

(NEC), NFPA 70, article 501.

WARNING – EXPLOSION HAZARD

6XEVWLWXWLRQRIDQ\FRPSRQHQWVPD\LPSDLUVXLWDELOLW\IRUKD]DUGRXVORFDWLRQVRUH[SORVLYHDWPRVSKHUHV

WARNING – EXPLOSION HAZARD

'RQRWGLVFRQQHFWHTXLSPHQWXQOHVVSRZHUKDVEHHQVZLWFKHGRႇRUWKHDUHDLVNQRZQWREHQRQKD]DUGRXV

7ˑ˒˜˒˜ˊ˗˘˙ˎ˗˝ˢ˙ˎˍˎ˟˒ˌˎ˝ˑˊ˝˒˜˝˘ˋˎ˒˗˜˝ˊ˕˕ˎˍ˒˗ˊ˗ˎ˗ˌ˕˘˜˞˛ˎ˜˞˒˝ˊˋ˕ˎ

ˏ˘˛˝ˑˎˎ˗˟˒˛˘˗˖ˎ˗˝ˊ˗ˍˊˌˌˎ˜˜˒ˋ˕ˎˎˡˌ˕˞˜˒˟ˎ˕ˢˠ˒˝ˑ˝ˑˎ˞˜ˎ˘ˏˊ˝˘˘˕

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

13

 CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU and 2015/863/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/30/EU (EMC)

Directive of the European Parliament and of the Council on the

harmonisation of the laws of the Member States relating to

electromagnetic compatibility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be available to the relevant authorities at the following

address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

www.hirschmann.com

The device can be used in the industrial sector.

 Interference immunity: EN 61000-6-2

 Emitted interference: EN 55032

You find more information on technical standards here:

“Technical data” on page 54

The assembly guidelines provided in these instructions must be strictly

adhered to in order to observe the EMC threshold values.

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

14

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

 FCC note

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Industrial Ethernet BOBCAT Rail Switch

BRS20/22/30/32/40/42/50/52

U.S. Contact Information

Belden – St. Louis

1 N. Brentwood Blvd. 15th Floor

St. Louis, Missouri 63105, United States

Phone: 314.854.8000

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a residential area can also cause interference, and in this

case the user is obliged to cover the costs of removing the interference.

 Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

15

About this manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

Documentation mentioned in the “User Manual Installation” that is not

supplied with your device as a printout can be found as PDF files for

downloading on the Internet at: https://www.doc.hirschmann.com

16

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

Key

The symbols used in this manual have the following meanings:

 Listing

 Work step



Subheading

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

17

1 Description

1.1 General device description

The device is designed for the special requirements of industrial automation.

The device meets the relevant industry standards, provides very high

operational reliability, even under extreme conditions, and also long-term

reliability and flexibility.

The device allows you to set up switched Industrial Ethernet networks

according to standard IEEE 802.3.

You can choose from between a wide range of variants. You have the option

to set up your device individually based on different criteria:

 Number of ports

 Transmission speed

 Types of connectors

 Temperature range

 Supply voltage range

 Certifications

 Software level

 IP degree of protection: IP30 (plastic casing) or IP30/IP40 (metal casing)

Mounting the device

 Mounting on the DIN rail

You have the option of choosing various media to connect to the end devices

and other network components:

 Twisted pair cable

 Multimode F/O

 Singlemode F/O

There are convenient options for managing the device. Manage your devices

via:

 Web browser

 SSH

 Telnet

 Network management software (for example Industrial HiVision)

The Network Management Software Industrial HiVision provides you with

options for smooth configuration and monitoring. You find further

information on the Internet at the Hirschmann product pages:

http://www.hirschmann.com/en/QR/INET-Industrial-HiVision

 USB-C interface (locally on the device)

18

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

The device provides you with a large range of functions, which the manuals

for the operating software inform you about. You can download these

manuals as PDF files from the Internet on the Hirschmann product pages

(http://www.doc.hirschmann.com).

1.2 Device name and product code

The device name corresponds to the product code. The product code is

made up of characteristics with defined positions. The characteristic values

stand for specific product properties.

You have numerous options of combining the device characteristics. You can

determine the possible combinations using the configurator which is

available in the Belden Online Catalog https://catalog.belden.com on the web

page of the device.

Item Characteristic Character

istic value

Description

1 ... 3 Product BRS BOBCAT Rail Switch

4 Data rate 2 100 Mbit/s

3 100/1000 Mbit/s

4 1000 Mbit/s

5 1000/2500 Mbit/s

5 Hardware type 0 Standard

2PoE

6 (hyphen) –

7 ... 8 Number:

100 Mbit/s ports

00 0 × 10/100 Mbit/s ports

04 4 × 10/100 Mbit/s ports

05 5 × 10/100 Mbit/s ports

06 6 × 10/100 Mbit/s ports

08 8 × 10/100 Mbit/s ports

09 9 × 10/100 Mbit/s ports

10 10 × 10/100 Mbit/s ports

11 11 × 10/100 Mbit/s ports

12 12 × 10/100 Mbit/s ports

9 ... 10 Number:

100/1000/

2500 Mbit/s ports

00 0 × 100/1000 Mbit/s ports

04 4 × 100/1000 Mbit/s ports

08 8 × 100/1000 Mbit/s ports

12 12 × 100/1000 Mbit/s ports

12 12 × 8 × 100/1000-Mbit/s-Ports + 4 × 100/1000/

2500 Mbit/s

Table 1: Device name and product code

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

19

11 ... 12 Configuration of

the first uplink

ports

99 Not present

M2 1 × DSC multimode socket for 100 Mbit/s F/O

connections

M4 1 × DST multimode socket for 100 Mbit/s fiber

optic connections

S2 1 × DSC singlemode socket for 100 Mbit/s F/O

connections

S4 1 × DST singlemode socket for 100 Mbit/s fiber

optic connections

E2 1 × DSC singlemode (plus) socket for 100 Mbit/

s fiber optic connections

L2 1 × DSC singlemode (LH) socket for 100 Mbit/s

fiber optic connections

G2 1 × DSC singlemode (LH) socket for 100 Mbit/s

fiber optic connections, 200 km

Z6 1 × SFP slot for 100 Mbit/s F/O connections

MM 2 × DSC multimode socket for 100 Mbit/s F/O

connections

NN 2 × DST multimode socket for 100 Mbit/s fiber

optic connections

VV 2 × DSC singlemode socket for 100 Mbit/s F/O

connections

UU 2 × DST singlemode socket for 100 Mbit/s fiber

optic connections

EE 2 × DSC singlemode (plus) socket for 100 Mbit/

s fiber optic connections

LL 2 × DSC singlemode (LH) socket for 100 Mbit/s

fiber optic connections

GG 2 × DSC singlemode (LH) socket for 100 Mbit/s

fiber optic connections, 200 km

ZZ 2 × SFP slot for 100 Mbit/s F/O connections

OO 2 × SFP slot for 100/1000 Mbit/s F/O

connections

2Q 2 × SFP slot for 100/1000/2500 Mbit/s fiber

optic connections

Item Characteristic Character

istic value

Description

Table 1: Device name and product code

20

Installation BRS20/22/30/32/40/42/50/52

Release

06

03/2020

13 ... 14 Configuration of

the second uplink

ports

99 Not present

M2 1 × DSC multimode socket for 100 Mbit/s F/O

connections

M4 1 × DST multimode socket for 100 Mbit/s fiber

optic connections

S2 1 × DSC singlemode socket for 100 Mbit/s F/O

connections

S4 1 × DST singlemode socket for 100 Mbit/s fiber

optic connections

E2 1 × DSC singlemode (plus) socket for 100 Mbit/

s fiber optic connections

L2 1 × DSC singlemode (LH) socket for 100 Mbit/s

fiber optic connections

G2 1 × DSC singlemode (LH) socket for 100 Mbit/s

fiber optic connections, 200 km

Z6 1 × SFP slot for 100 Mbit/s F/O connections

ZZ 2 × SFP slot for 100 Mbit/s F/O connections

OO 2 × SFP slot for 100/1000 Mbit/s F/O

connections

2Q 2 × SFP slot for 100/1000/2500 Mbit/s fiber

optic connections

15 (hyphen) –

16 Temperature

range

S Standard +32 °F ... +140 °F (0 °C ...

+60 °C)

C Standard

with Conformal

Coating

+32 °F ... +140 °F (0 °C ...

+60 °C)

T Extended -40 °F ... +158 °F (-40 °C ...

+70 °C)

E Extended

with Conformal

Coating

-40 °F ... +158 °F (-40 °C ...

+70 °C)

17 Supply voltage T 2 × 12 V DC ... 24 V DC

U2×24VDC

F 2 × 24 V DC ... 48 V DC / 24 V AC

P 2 × 48 V DC (PoE) / 54 V DC (PoE+)

18 Housing C IP30 Plastic

DIP30Metal

EIP40Metal

19 Certificates and

declarations

a

Part A

Z CE, FCC, EN 61131-2, EN 62368-1, (NEMA TS2

b

)

Y Z + cUL 61010

X cUL 61010 + ANSI/UL 121201

V Z + IEC 61850-3

U Z + DNV GL

W Z+ATEX/IECEx

T Z + EN 50121-4

Item Characteristic Character

istic value

Description

Table 1: Device name and product code

Page is loading ...

Belden HIRSCHMANN BRS40 User manual

This manual is also suitable for

Belden HIRSCHMANN BRS40 User manual

Related papers

Other documents