CyberData 011416 - CALL FOR PRICING Owner's manual

Brand: CyberData

Model: 011416 - CALL FOR PRICING

Type: Owner's manual

This manual is also suitable for

Getting Started

Take the following into consideration before you install this product:

• When this secure phone case is used, the touch screen capability of the DX phone is disabled.

• Due to the size and mass of this product, it is important that the Backbox is safely installed according to these installation

instructions.

• Make sure that the type of wall is capable of supporting the system and use screws that are suitable for that type of wall.

• The system must be installed by qualified personnel in accordance with state and local building regulations.

• Also see the Install the DX80 Phone to Enclosure (on the other page).

• Locate the provided Security Torx Driver Bit (usually taped right next to the Hookswitch on the Faceplate).

• Tool required to remove Security Torx Screws (an Electric Hand Drill or Powered Screwdriver)

• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation

instructions.

• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.

• WARNING: This enclosure is not rated for any AC voltages!

Hookswitch Wires to USB to Analog Audio Module Connections

Contacting CyberData

USB - B Plug

on DX80

USB - A to B Cable

Plug in to Connector Panel

Plug in to (J1)

USB - A Plug

FACTORY DISCONNECTED

RE-CONNECT BEFORE FASTEN

FACEPLATE TO BACKBOX

***

ASSEMBLY

HOOKSWITCH

WIRES TO SOCKET

SOCKET

PLUG

FACTORY PRE-INSTALLED

WIRES TO SOCKET

Sales: 831-373-2601 ext. 334

Support: 831-373-2601 ext. 333

Support Website: http://support.cyberdata.net/

RMA Department: 831-373-2601 ext. 136

RMA Email: [email protected]

RMA Status: http://support.cyberdata.net/

Warranty Information: http://support.cyberdata.net/

Corporate Headquarters

CyberData Corporation

3 Justin Court

Monterey, CA 93940, USA

Phone: 831-373-2601

Fax: 831-373-4193

http://www.cyberdata.net/

Backbox Mounting

Armored Cord Handset to USB to Analog Audio Module

Tool Required for Knock Out Removal:

1) Hammer

2) Blade Screwdriver

One Inch EMT Fitting

Knock Out

Conduit Hole Fits

Knock Out

Ø0.63 [Ø16.0]

Ø0.41 [Ø10.5]

Ø1.30 [Ø33.0]

View Shown with Hole Plug Installed.

Open Faceplate then Remove Nut from the Inside.

1/4"- 20 Thread Size

Keyholes & Holes Fits Up to

Stud Anchor/Screw/Bolt

(Optional) SPAR II - RTFM Access Hole

with Handsfree Kit (P/N: 081136A)

Replaceable Coverplate

(Sold Separate) for Handsfree Operation

T15H Security Torx Screw Installed from the Inside

1.969 [50.00]

5.118 [130.00]

2.047 [52.00]

4.016 [102.00]

1.969 [50.00]

19.685 [500.00]

9.843 [250.00]

3.602 [91.50]

15.748 [400.00]

4.016 [102.00]

9.114 [231.50]

3.937 [100.00]

12.567 [319.19]

13.780 [350.00]

9.114 [231.50]

Electro-Galvanized Steel Constructed Backbox with

1.6 mm Thick

Silver Hammertone Polyester PowderCoat

11/32" or 9mm Socket & Socket Wrench

Tool Required to Remove Hole Plug:

Last Updated 08/04/2020

Red Wire to J4 (Position 1)

Green Wire to J4 (Position 3)

Black Wire to J4 (Position 4)

Yellow Wire to J4 (Position 2)

1) #00 size Phillips Screw Driver

Tool Provided for Terminal Block Screw:

Armored Cord Wires End

The IP Endpoint Company

Installation Quick Reference

DX80 Secure Phone

011416

Install the DX80 Phone to Enclosure

Connections

Label

2) Screw Driver

1) Hammer

Tool Required to Remove Knock Outs (KO):

3) Plier

1/4" Self-Tapping Screw

Up to 1/4" Square Neck Carriage Bolt

Knock Outs (KO) & Keyhole Fit:

or 10 Millimeter Machine Screw

Use Provided Security Torx

Driver Bit to Fasten Screws

Place Phone

Power Supply

inside Holder

Use Clean Damp Cloth to Wipe Surface Clean

Screen Cleaning Instruction:

Plexiglass Cleaning Instruction:

Plexiglass Cleaner to Wipe Surface Clean

ASSEMBLY

FACEPLATE

ASSEMBLY

BACKBOX

Phone Mounting Instruction:

Plug Power Plug

in to Power Jack

on the Connector Panel

to Backbox

To Remove Phone from Backbox:

See Hookswitch to

USB to Analog Audio Module Diagram

for Detail Connections

IEC Power Cord

the Other Through Any Available

Conduit Hole Exit to Power Source

Fits Size #8 or M4 Ring Terminal

Connector Cover

Turn to Open Lens Cover

Sightly Push Downward to Engage Locking

5) Place Strain Relief Bar on Top of CLAMP

Camera

Holder

on DX80 Phone

Foot Stand

CLAMP

Strain Relief Bar

1) Lift Connector Cover Up

Plate

3) Place Foot Stand Behind Plate

4) Place Microphone on to Stand

Microphone

Stand

Use a Paper Clip Through Hole

to Access Power Button

Camera

2) Plug in All Neccessary Cables,

Cables Must be Placed Behind Strain Relief Bar

Front

Behind

1) Lift Phone Up in Slow Motion then Disconnect

All Cable from Connector Panel

CLAMP

Ground Lug

Torx Sec. Bit & Spare Screw Kit

#6-32x5/8"Flat Head

Pin Torx Machine Screw

(Spare - 2 Pieces)

Cable Management Kit

T-15 Pin Torx

6" Wire Tie (2x)

Wire Tie Mounting

1.5" Square

Base (2x)

Accessory Kit

#00 Screw Driver Kit

Cable Management Kit

#8 Hex Nut

Security Driver Bit

#6-32 x 3/16”

Button Head Torx

Machine Screw

(Spare)

(GND Lug)

Jumper Shunt

1/16” Hex L-Key

Acrylic Bezel Remove Kit

Acrylite AR - Anti-Scratch

Resistance Coating on the Outside

JP2

Shunt

Install a Shunt on JP2 to

Enable Auto Answer Mode

CyberData 011416 - CALL FOR PRICING Owner's manual

Brand: CyberData

Model: 011416 - CALL FOR PRICING

Type: Owner's manual

This manual is also suitable for

Download PDF

report

CyberData 011416 - CALL FOR PRICING Owner's manual

This manual is also suitable for

CyberData 011416 - CALL FOR PRICING Owner's manual

Related papers

Other documents