iKey SL-86-911-FSR-461 Assembly Instructions

iKey
Brand
iKey
Model
SL-86-911-FSR-461
Category
Motorcycle Accessories
Type
Assembly Instructions

iKey SL-86-911-FSR-461 is a versatile input device that combines a 46-key silicone keypad with a precision HulaPoint™ sensor/joystick. This unique combination makes it an ideal choice for a wide range of applications, including industrial control, medical devices, and gaming.

The silicone keypad provides tactile feedback and is highly resistant to wear and tear, making it suitable for even the most demanding environments. The HulaPoint™ sensor/joystick offers precise cursor control and can be used for navigation, selection, and other control functions.

The iKey SL-86-911-FSR-461 is easy to install and use. It can be mounted in a panel or enclosure using the included hardware, and the keypad can be customized to meet your specific needs. The device is also compatible with a variety of operating systems, making it easy to integrate into your existing setup.

iKey SL-86-911-FSR-461 is a versatile input device that combines a 46-key silicone keypad with a precision HulaPoint™ sensor/joystick. This unique combination makes it an ideal choice for a wide range of applications, including industrial control, medical devices, and gaming.

The silicone keypad provides tactile feedback and is highly resistant to wear and tear, making it suitable for even the most demanding environments. The HulaPoint™ sensor/joystick offers precise cursor control and can be used for navigation, selection, and other control functions.

The iKey SL-86-911-FSR-461 is easy to install and use. It can be mounted in a panel or enclosure using the included hardware, and the keypad can be customized to meet your specific needs. The device is also compatible with a variety of operating systems, making it easy to integrate into your existing setup.

Last Revised: 9/19/08
Step 1: Materials Needed for an OEM Assembly
1. OEM Printed Circuit Board
2. Silicone Rubber Keypad Overlay
3. Cable
4. Silicone RTV Glue
Step 2: Applying Adhesive to Silicone Overlay
Apply silicone adhesive [iKey recommends SuperFlex by Loctite] to back side of silicone
overlay (keypad). Sparingly dab glue on the middle of each key intersection across the
whole keyboard as seen in this picture. Also apply to inside of center portion of
HulaPoint™ pad (where the sensor/joystick lies) if OEM kit incorporates the HulaPoint™
Be careful not to drop silicone on any key contacts.
Glue
Back of silicone keypad
Back of silicone keypad
Key
Contacts
Key
Contacts
Glue
Glue
Glue
Glue
Glue
Last Revised: 9/19/08
INCORRECT GLUING PROCEDURE
Step 3: Placing Keypad in Enclosure
1. Put the silicone rubber keypad into place on the panel or enclosure you
are using. Do not place PCB yet.
2. Seat the keypad in the mounting cutout by sliding one edge at a time into
the cutout space.
3. Spread the keypad to be sure it is well seated on all four sides. Ensure
that the lip is through the cutout all the way around the pad.
4. When the keypad is in place, gently allow the board to fall into place on
top of the keypad so no glue is displaced onto a key trace, or key contact.
(Note: make sure the PCB and pad are oriented in the same direction.)
5. Tighten hex nuts until keypad is just SLIGHTLY compressed between
panel and PCB. We recommend 1.5 in/lbs. of torque when tightening.
6. Run fingers between all keys to ensure a good silicon and PCB bond.
7. Allow glue to cure for 1 hour
Glue
Glue
Panel
Panel
Back Side
of PCB
BACK
BACK
Mounting
Studs
Panel or
Enclosure
PCB
Keypad
Last Revised: 9/19/08
Step 4: Wiring for Keyboard
Add a dab or two of glue on the PCB just in front of the connector so that the cable
header will sit on the glue when connected to the board and make itself more secure.
The picture above illustrates the placement of the glue prior to the connection
USB Cable: Green, White, [Space}, Black, Red
PS/2: Purple, Yellow, [Space], Green, Blue, Yellow, Black, Matte Black, Brown,
Red
P1
Glue
Glue
Back of PCB near
connector P1
Pin 1
Last Revised: 9/19/08
Custom Cables Signal Layout
Next, connect the cable onto the prongs of J1 as shown above.
* Used for USB interface
** Downstreaming a Mouse Unit* The board MUST be in USB mode to be able
to downstream a mouse.
You’re iKey unit is now ready to use with your set up.
If you should have any additional questions, please feel free to contact iKey
directly at (800) 866-6506 or send an e-mail to support.
Keyboard
**Downstream Mouse
J1 (1x5 Header)
J2 (1x5 Header)
PIN
Connectivity Function
PIN
Connectivity Function
1
PS2 Clock/D+ *
1
Clock
3
PS2 Data/D- *
2
Data
5
Chassis Ground
3
Chassis Ground/Drain
7
Signal Ground
4
Signal Ground
9
Power (+5 VDC)
5
Power (+5V)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

iKey SL-86-911-FSR-461 Assembly Instructions

iKey
Brand
iKey
Model
SL-86-911-FSR-461
Category
Motorcycle Accessories
Type
Assembly Instructions

iKey SL-86-911-FSR-461 is a versatile input device that combines a 46-key silicone keypad with a precision HulaPoint™ sensor/joystick. This unique combination makes it an ideal choice for a wide range of applications, including industrial control, medical devices, and gaming.

The silicone keypad provides tactile feedback and is highly resistant to wear and tear, making it suitable for even the most demanding environments. The HulaPoint™ sensor/joystick offers precise cursor control and can be used for navigation, selection, and other control functions.

The iKey SL-86-911-FSR-461 is easy to install and use. It can be mounted in a panel or enclosure using the included hardware, and the keypad can be customized to meet your specific needs. The device is also compatible with a variety of operating systems, making it easy to integrate into your existing setup.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents