25706879 9/12
© 2012 Evenflo Company, Inc.
Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE.
Lire les instructions AVANT l’assemblage et L’UTILISATION du produit. CONSERVER CES INSTRUCTIONS POUR RÉFÉRENCE ULTÉRIOR.
Lea las instrucciones ANTES de armar y USAR el producto. GUARDE ESTAS INSTUCCIONES PARA REFERENCIA FUTURA.
Centre d’apprentissage actif • Centro de aprendizaje activo
“A Safer Alternative” to Walkers
Une alternative plus sécuritaire aux marchettes
Una alternativa más segura a las andaderas
Feet (2 - Green)
Phillips Screwdriver
CAUTION: Tighten all screws until snug; do not overtighten. Use only #6 x 3/4” (3.5 x 19 mm) screws (included).
DO NOT USE POWER TOOLS.
Tray Half (2 - Green)
Seat Pad (1)
Base (1 - Blue)
Lower Leg
Pedestal (4 - Teal)
Lower Leg (4 - Teal)
Seat Ring (1)
Upper Leg
Crown (4 - Teal)
Upper Leg (4 - Teal)
Hardware Kit Bag (1)
1 Instructions
24 Screws–#6x3/4”(3.5 x 19 mm)
4 Washers
4 Large springs
4 1-3/4” (44.5 mm) springs
4 1-1/2” (38 mm) springs
2 End Caps*
4 Leg Locks*
4 Pylon Rings*
4 Stabilizer Feet
6 Seat Wheels
Toy Kit Bag (1)
8 Toys
WARNING
*Pylon Ring (4 - Green)
*End Caps (2 - Green)
*Leg Lock (4 - Green)
1
Playmat (1)
• www.evenflo.com • USA: 1-800-233-5921, 8 AM – 5PM E.T.
• Canada: 1-937-773-3971 • México: 01-800-706-12-00
READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS! FAILURE TO DO SO COULD RESULT IN
SERIOUS INJURY OR DEATH!
• NEVER leave child unattended. ALWAYS keep child in view while in the ExerSaucer
®
.
• Read all instructions before assembly and use of the ExerSaucer
®
.
• Keep instructions for future use.
• Keep children away from unassembled product.
• Adult assembly required. Take care when unpacking and assembling; contains small parts and sharp edges.
• To prevent a possible choking hazard, remove and immediately discard packing material before using this product.
• STRINGS CAN CAUSE STRANGULATION!
- DO NOT place the ExerSaucer
®
anywhere near cords from window blinds, draperies, phone, etc.
- DO NOT place items with strings, such as hood strings or pacifier cords, around your child’s neck .
- DO NOT suspend strings over product or attach strings to toys.
• To avoid possible entanglement or strangulation (on Stage 1), remove toy bar when baby begins to push up on hands
and knees.
• NEVER use near stairs or steps.
• NEVER use ExerSaucer
®
near ranges, radiators, space heaters, and fireplaces.
• NEVER use ExerSaucer
®
in or near swimming pools or other bodies of water.
• DO NOT fill the ExerSaucer
®
tray with water.
• DO NOT fold or adjust height while baby is sitting in ExerSaucer
®
.
• DO NOT use the ExerSaucer
®
if any parts are missing or broken.
• NEVER use as a sled.
• DO NOT allow child to sleep in ExerSaucer
®
(Stage 2).
• DO NOT spin baby in seat. Only permit baby to rotate the seat.
• Stage 2 is for use by children who are at least 4 months old AND can hold up their head and neck unassisted.
• Stop using Stage 2 when your child reaches any of the following developmental stages:
- Can walk by himself/herself
- Is over 30” (76 cm) tall
- Can climb out of the product
- Can stand flat-footed in the ExerSaucer
®
in the highest adjustment level
• Allow only the baby’s toes to touch the base. DO NOT allow the baby to stand flat-footed on the base.
• DO NOT use or store this product outdoors.
• To avoid tip-over, place product on flat, level floor.
• NEVER place playmat from Stage 1 in the bottom of saucer.
• DO NOT mix old and new batteries.
• DO NOT mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. Only batteries of the same or
equivalent type, as recommended, are to be used.
• DO NOT dispose of batteries in fire, as batteries may explode or leak.
• DO NOT use rechargeable batteries.
• DO NOT recharge non-rechargeable batteries.
• Promptly remove old batteries from the toy.
• Remove batteries before storing unit for a prolonged period of time.
Table of Contents
Tools Required
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Stage 1 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Stage 2 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Stage 2 Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Stage 2 Tray Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Stage 2 Seat Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Toy Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Folding/Unfolding Stage 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Stage 3 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Large
Small
Registration Information
Please register this product so we can reach you if there is a safety alert or recall. We will not sell, rent, or share your personal infor-
mation. To register your product, please complete and mail the card that came with it or visit our online registration at
www.evenflo.com/registerproduct.
For future reference, record the Model Number and Date of Manufacture below.
Model Number: Date of Manufacture:
F
J
1. Place mat A on floor.
2. Place feet B on either side of mat, as shown.
3.lnstall toy bar C into feet, as shown. Press toy bar down
firmly and rotate until it snaps into place. Pull up on the toy
bar and stalk toys installed into the feet to make sure they
are locked in place.
3
2
2. Locate four pedestals C, then turn over and install the
1-1/2 inch (38 mm) spring D with screw E in each
pedestal. Position spring as shown. Do not overtighten
screw.
3.To install a pedestal
C, hold it above the base F so that
the locking tab with the rib G lines up directly over the
slot with the notch H.
D
E
D
A
C
B
B
Stage 1 is used for infants from birth to 4 months old.
Stage 1
Stage 2 is used for infants 4 months old (who can hold up head and neck unassisted)
to walking age and under 30 inches tall.
C
F
C
G
H
A
B
1. Turn base A upside down and locate four stabilizer feet B.
Insert one side of foot B into the foot bracket hole and twist
the foot until the other side snaps into the opposite hole, as
shown. Repeat until all four stabilizer feet are installed.
To use stabilizer feet:
Flip the four stabilizer feet out from beneath base to prevent
ExerSaucer
®
from rocking.
Stage 2 Base Assembly
4.Attach the spring D to the hook I on the base F, as
shown. Once the spring is in place, align all three locking
tabs J on the pedestal with the slots in the base and snap
the pedestal into place.
D
I
Stage 1
Stage 2 Stage 2
B
5.Turn the base F upside down and make sure the
locking tabs J on each pedestal C are completely pushed
through to the underside of the base F and have locked
over the edge of the openings, as shown.
6.Check to ensure that the locking tabs are installed properly
by turning the pedestal
C clockwise, then releasing.
The pedestal MUST spring back into place.
Repeat for all four pedestals.
F
C
J
C
C
1
2
3
4
54
1.Locate two tray halves
A. Install spring B, upper leg
crown C, and pylon ring D onto one of the tray halves.
Secure with four screws E.
Note: Hold the upper leg crown C and pylon ring D
securely while installing screws. Tension from the spring will
try to push the upper leg crown and pylon ring upward.
Repeat for other upper leg crown on this tray and for both
upper leg crowns on the other tray half.
A
C
B
E
Install and tighten screws on the
pylon ring D in the following
sequence.
Stage 2 Tray Assembly
Stage 2 Tray Assembly
TIP
M
D
D
Stage 2 Base Assembly
2.Insert upper leg F into the upper leg crown C until it
snaps into place. Pull up on upper leg F to ensure it is
securely installed in upper leg crown C.
Repeat until all four upper leg assemblies are
complete.
Note: Make sure the adjustment holes on the front of
all four upper legs F are facing the outer edge of the
tray A, as shown.
A
F
F
F
C
G
I
3. Slide one end of 1-3/4 inch (44.5 mm) spring G into the
spring notch H in leg lock I, as shown.
Note: Once the spring has been installed correctly, it will
stay in place. Repeat for all four leg locks.
4.Set one leg lock I on the pylon ring D and on the tray A,
as shown.
Note: The Side Cutaway View above illustrates how the
spring G must rest against the spring tab J so the leg
lock I will operate properly.
I
D
A
H
J
D
G
I
Side Cutaway View
5. Push downward on the leg lock I (against the pylon
ring D and the tray A) while pulling it toward you until it
slides off of the pylon ring, as shown.
6.While holding the leg lock
I, allow the spring to pull the
leg lock back toward the upper leg as you guide it through
the pylon ring D, as shown.
D
I
A
I
D
C
M
M
C
M
C
M
C
7.Insert lower leg assembly M at an angle (as shown) onto top of pedestal C, then
rock gently while applying a steady downward pressure until it snaps into place.
Swing lower leg assembly M up until it locks in the upright position. Repeat for all
four leg assemblies.
You are now finished assembling the base. Set it aside so you can assemble the tray.
7
6
7. Secure the leg lock
I with screw E and washer K.
Do not overtighten.
Note: Check that each leg lock is installed correctly by
pulling backward, then releasing it. If the leg lock springs
back into positon, it is installed correctly. If it does not spring
back into position, remove the screw and washer and repeat
Steps 5 and 6. Repeat for all legs.
I
I
Stage 2 Seat Assembly
E
K
Stage 2 Tray Assembly
A
A
8.Assemble the tray by snapping both tray
halves A together, as shown.
Note: Make sure the tray halves lock
securely.
N
O
N
3.Press assembled seat ring H down firmly onto the top of the tray I
until it snaps into place and spins freely.
2.Turn seat ring
A right side up. Align triangle D on
the back of the seat ring with the triangle E on the
seat pad label. Snap the plastic tabs F on the pad
over the pegs G on the seat ring. Continue this
process until all tabs are attached to all pegs.
1.Place seat ring
A upside down and locate the wheel
holders B. Snap six (6) seat wheels C into wheel
holders, as shown.
F
G
A
E
D
H
I
B
C
B
A
P
Q
P
9. Locate the large end cap N and press it onto
mounting posts O for storage, as shown.
Locate the small end cap P and press it onto
mounting posts Q for storage, as shown.
9
8
Toy Assembly Stage 2 Seat Assembly
B
C
Align and start each upper leg A into the lower leg openings B.
Push button C and guide upper leg into lower leg until upper
leg snaps into place.
Allow only the baby’s toes to touch the base. DO NOT allow
the baby to stand flat-footed on the base. As baby grows and
becomes more active, raise the tray to the next level so that
baby enjoys the most comfortable fit and maximum use of the
spin and bounce features.
To adjust height:
ALWAYS remove baby from ExerSaucer
®
before adjusting.
Push the button
C until the desired position is obtained.
Make sure that all four legs are adjusted to the same position.
C
WARNING
ON/OFF
3 “AAA” Batteries
3 “AAA” Batteries
3 “AAA” Batteries
ON/OFF
ON/OFF
A
11
10
Folding/Unfolding Stage 2
2.To unfold the ExerSaucer
®
, release the four tray
locks F by pulling them outward from the base E,
as shown.
Hold the base down with your foot, and pull the tray
upward. The tray will rotate as you pull and the legs will
lock in the upright position. The leg assemblies
B will
lock onto the pedestals G.
Twist the tray to make sure all legs are locked properly.
IMPORTANT: Make sure all four leg assemblies B are
firmly locked onto the pedestals G before use.
12
G
B
G
F
E
C
E
B
1.To fold ExerSaucer
®
, ALWAYS remove baby and toy
bar A from ExerSaucer
®
before folding.
With ExerSaucer
®
flat on the floor, twist each leg
assembly B fully clockwise (the direction of the arrow)
until it stops in the position shown.
Fully depress one of the pedestal locking tabs C then
push on the leg assembly B; leg will partially fold. Repeat
this procedure for all four legs.
After pressing the fourth pedestal locking tab
C, the
ExerSaucer
®
will fold with the tray D rotating toward the
base E. Make sure all four tray locks F are locked onto
the base before trying to carry ExerSaucer
®
.
Note: Make sure the legs are at the same height
adjustment or the ExerSaucer
®
will bind and not fold
properly (refer to page 8).
A
B
B
D
F
F
F
1.Remove toys and seat from the ExerSaucer
®
.
2.Follow Step 1 on page 10 to fold the ExerSaucer
®
, but
do not let the tray lock to the base.
3.Place your fingers beneath the legs A, as shown, and
push upward to disconnect the leg assemblies from the
pedestals B. Repeat for all four leg assemblies.
4.After all four legs have been disconnected from the
pedestals, remove tray assembly C from the base D.
Stage 3 is used for children who are walking age to 24 months.
IMPORTANT: Child should not use the activity table if they can not stand up by themselves.
Stage 3
Stage 3
C
C
D
E
F
A
B
C
C
G
6.Squeeze both locking tabs G on
each side of the tray to disconnect
and separate the tray halves C.
Re-position them as shown.
B
A
5.Turn tray C upside down and remove the large end cap E
and the small end cap F from from beneath.
8.Rotate leg assemblies A fully counterclockwise, (the
direction of the arrow) until they lock into the position
shown. Make sure that all four leg locks H are locked
properly into the upper leg crown I, as shown
above. Also, make sure the ends of all four leg
locks H are sticking out past the edge of the tray,
as shown.
IMPORTANT: DO NOT use this activity table unless
the legs have locked into place!
13
12
Stage 3 Assembly Stage 3 Assembly
7.Connect tray halves C to form activity table.
Note: Make sure the tray halves lock securely.
C
C
A
A
A
A
H
I
H
H
F
F
E
G
F
9. Install the small end cap F, as shown. Make sure the
locking tabs G have locked over the edge of the
opening, as shown.
10. Turn table over and install the large end cap
E, as
shown. Make sure both end caps E and F are
locked into place.
11. Install toys on activity table. If desired, adjust table to
the appropriate height (page 8) for your child.
Note: Always make sure that all four legs are
adjusted to the same height.
IMPORTANT: NEVER use Stage 3 without end caps!
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
• This Class B digital apparatus complies with Canadian ICES-003.
14
15
For Plastic Parts:
Wipe surface clean with cloth slightly moistened with mild soap and water. Allow to air dry.
For Seat Pad and Playmat:
For Best Results
Machine Wash Separately, Cold Water – Delicate Cycle. NO CHLORINE BLEACH.
Tumble Dry: 10 – 15 Minutes on Low Heat – Remove Immediately.
If musical toys fail to operate, check the batteries. Note: ONLY the AAA batteries are replaceable. Dispose of old batteries safely.
DO NOT use this product if any parts are damaged or broken.
Limited Warranty
For a period of 90 days from the original purchase of this Product, Evenflo warrants to the original end user ("Purchaser") this
Product (including any accessories) against defects in material or workmanship. Evenflo’s sole obligation under this express
limited warranty shall be, at Evenflo’s option, to repair or replace any Product that is determined to be defective by Evenflo
and determined to be covered by this warranty.
Repair or replacement as provided under this warranty is the exclusive remedy of the Purchaser. Proof of purchase in the form
of a receipted invoice or bill of sale evidencing that the Product is within the warranty period must be presented to obtain
warranty service. This express limited warranty is extended by Evenflo ONLY to the original Purchaser of the Product and is not
assignable or transferable to subsequent purchasers or end users of the Product. For warranty service, contact Evenflo’s
ParentLink Consumer Resource Center at
(800) 233-5921 or www.evenflo.com.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE ON THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO SHALL NOT BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED WARRANTY ON
THIS PRODUCT, OR ANY WARRANTY IMPLIED BY OPERATION OF LAW. OTHER THAN THE EXPRESS LIMITED WARRANTY SET
FORTH ABOVE, THERE ARE NO OTHER WARRANTIES THAT ACCOMPANY THIS PRODUCT AND ANY ORAL, WRITTEN OR ANY
OTHER EXPRESS REPRESENTATION OF ANY KIND IS HEREBY DISCLAIMED.
•
www.evenflo.com • USA: 1-800-233-5921 8 AM – 5 PM E.T.
• Canada: 1-937-773-3971 • México: 01-800-706-12-00
WARNING
BATTERY INFORMATION
Battery life varies with use.
Safety Information: Batteries are small objects. Batteries must be replaced by adults. Follow the polarity (+/-) diagram in the
battery compartment.
• DO NOT mix old and new batteries.
• DO NOT mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
• Remove batteries before storing unit for a prolonged period of time.
• DO NOT allow unit to get wet.
• Promptly remove dead batteries from the toy.
• Dispose of used batteries properly.
• Only batteries of the same or equivalent type, as recommended, are to be used.
• DO NOT dispose of batteries in fire, as batteries may explode or leak.
• DO NOT use rechargeable batteries.
• DO NOT recharge non-rechargeable batteries.
Battery Replacement: To replace batteries, loosen screw and remove battery door. Discard old batteries properly and replace
with 3 AAA alkaline batteries. Replace door and tighten screw.
Troubleshooting:
Toy does not turn on or does not respond.
• Make sure batteries are installed correctly.
• Make sure battery cover is correctly secured.
• Install new batteries.
Toy makes improper responses.
• Check or install new batteries.
WARNING
Care and Maintenance
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
