Evenflo 2-in-1 Activity Center and Art Table User manual

25701113 8/17

KEEP INSTRUCTIONS FOR FUTURE USE.

Read all instructions BEFORE assembly and USE of product.

CONSERVER CES INSTRUCTIONS POUR RÉFÉRENCE ULTÉRIEURE.

Lire les instructions AVANT l’assemblage et L’UTILISATION du produit.

GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA.

Lea las instrucciones ANTES de armar y USAR el producto.

2 in 1 Activity Center and Art Table

Centre d’activités 2 en 1 et tablette d’artiste

Centro de actividades 2 en 1 y mesa de arte

1

(1) Hardware Kit Bag includes:

1 Instructions

4 Lock Guides

4 Hand Locks

6 Seat Wheels

6 Toys

Quantity and style of toys may

vary.

WARNING

Table of Contents

Tray

Seat Pad

Base

Base Cap

Seat Ring

Leg (4)

Hand Lock (4)

Bounce Ring

Lock Guide (4)

Registration Information

Please register this product so we can reach you if there is a safety alert or recall. We will not

sell, rent, or share your personal information. To register your product, please complete and

mail the card that came with it or visit our online registration at

www.evenflo.com/registerproduct

For future reference, record the Model Number and Date of Manufacture below.

Model Number: Date of Manufacture:

READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS!

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH!

• NEVER leave child unattended. ALWAYS keep child in view while in the

ExerSaucer.

• Read all instructions before assembly and use of the ExerSaucer.

• Keep instructions for future use.

• Keep children away from unassembled product.

• Adult assembly required. Take care when unpacking and assembling; contains

small parts and some items with sharp edges.

• To prevent a possible choking hazard, remove and immediately discard packing

material before using this product.

• Strings Can Cause Strangulation!

• DO NOT place the ExerSaucer anywhere near cords from window blinds,

draperies, phone, etc.

• DO NOT place items with strings, such as hood strings or paciﬁer cords,

around your child’s neck.

• DO NOT suspend strings over product or attach strings to toys.

• NEVER use near stairs or steps.

• NEVER use ExerSaucer near ranges, radiators, space heaters, ﬁreplaces or any

other heat source.

• NEVER use ExerSaucer in or near swimming pools or other bodies of water.

• DO NOT ﬁll the ExerSaucer tray with water.

• DO NOT adjust height while baby is sitting in ExerSaucer.

• DO NOT use the ExerSaucer if any parts are missing, damaged or broken.

• DO NOT allow child to sleep in ExerSaucer.

• DO NOT spin baby in seat. Only permit baby to rotate the seat.

• Toys with cap MUST be in place when Stage 1 is in use.

• Stage 1 is for use by children who are at least 4 months old AND can hold up

their head and neck unassisted.

• Stop using Stage 1 when your child reaches any of the following developmental

stages:

• Can walk unassisted

• Is over 30” (76 cm) tall

• Can climb out of the product

• Can stand ﬂat-footed in the ExerSaucer in the highest adjustment level

• Allow only the baby’s toes to touch the base. DO NOT allow the baby to stand

ﬂat-footed on the base.

• DO NOT use or store this product outdoors.

• To avoid tip-over, place product on ﬂat, level ﬂoor.

• Stage 2 is for use by children who can walk unassisted up to approximately 48

months.

• Stage 2 Art Table MUST be in highest position at all times

• DO NOT mix old and new batteries.

• DO NOT mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium)

batteries.

• Only batteries of the same or equivalent type, as recommended, are to be used.

• www.evenflo.com • USA: 1-800-233-5921, 8 AM – 5PM E.T.

• Canada: 1-937-773-3971 • México: 01-800-706-12-00

Warnings

D

H

I

G

B C

A

E

B–

C–

F–

D> !

J–

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Assembling the ExerSaucer® - Stage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Attaching the Toys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Assembling the Art Table - Stage 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Tools Required

Phillips Screwdriver

CAUTION: Tighten all screws until snug; do not overtighten. Use only screws provided.

DO NOT USE POWER TOOLS.

2 3

Assembling the ExerSaucer

Warnings - continued Assembling the ExerSaucer

1. Press Lock Guide

B

into Leg

A

, as shown, to create the Leg Assembly. Make

sure Lock Guide is facing in the correct direction (see illustration). Repeat for the

other three Leg Assemblies.

2. Place end of Leg Assembly

A

into opening on bottom of Tray

D

. Make sure

Lock Guide

B

lines up with slot in bottom of Tray, as shown.

3. Lift Tray

D

until opening in Tray lines up with hole in Lock Guide

B

. Screw Hand

Lock

C

into hole in Lock Guide. Tighten Hand Lock until it no longer turns.

DO NOT OVERTIGHTEN. Repeat steps 2 and 3 for the other three Leg

Assemblies.

IMPORTANT: When inserting Hand Locks, use the same opening in each Leg

Assembly, or the ExerSaucer will not be level.

WARNING

READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS!

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY OR DEATH!

• DO NOT dispose of batteries in ﬁre, as batteries may explode or leak.

• The supply terminals are not to be short-circuited.

• DO NOT use rechargeable batteries.

• DO NOT recharge non-rechargeable batteries.

• Promptly remove exhausted batteries from the toy.

• Remove batteries before storing unit for a prolonged period of time.

• DO NOT allow unit to get wet.

• Dispose of used batteries properly.

STAGE 1 STAGE 1

A

B

D

C

B

Stage 1 is for use by children who are at least 4 months old

AND can hold up their head and neck unassisted.

WARNING

A

B

A

B

Make sure Lock Guide is

facing in the correct direction.

4 5

7. Turn Seat Ring

E

right side up. Align triangles

E> @

on the back of the Seat Ring

with the triangles

G> !

on the seat pad label. Snap the plastic tabs

G> @

on the

pad over the pegs

E> #

on the Seat Ring. Continue this process until all tabs are

attached to all pegs.

6. Place Seat Ring

E

upside down and locate the wheel holders

E> !

.

Click six (6) Seat Wheels

F

into wheel holders, as shown.

E> !

E

F

E

G

G> !

E> @

E> #

G> @

Assembling the ExerSaucer

8. Press assembled

Seat Ring

E> $

down firmly onto

the Bounce Ring

D> !

until it clicks

into place and

spins freely.

To adjust height:

ALWAYS remove baby from ExerSaucer before

adjusting.

Squeeze tabs

C> !

while unscrewing Hand Lock

C

.

Unscrew only far enough to free the Hand Lock

from the opening in the Tray. Move the Tray

up or down to the desired height, then tighten

the Hand Lock until it locks in place. DO NOT

OVERTIGHTEN.

IMPORTANT: When inserting Hand Locks, use

the same opening in each Leg Assembly, or the

ExerSaucer will not be level.

During use, allow the baby’s toes only to touch the Base. DO NOT allow

the baby to stand flat-footed on the Base. As baby grows and becomes

more active, raise the Tray to the next level so that baby enjoys the most

comfortable fit and maximum use of the spin, and bounce features.

E> $

D> !

Assembling the ExerSaucer

4. After all four Legs are locked in place,

turn the ExerSaucer right-side-up.

CLICK!

WARNING

Loosen Tighten

H

I

C> !

H A

CLICK!

5. Place Base

H

on Legs

A

under the

ExerSaucer. Make sure the Base is

resting in the notches on the Legs, as

shown. Then place the Base Cap

I

in

the center of the Base.

IMPORTANT: Base

H

MUST be in

place before using Stage 1.

Base Cap

I

MUST be placed in the

Base with the rim facing down, as

shown.

6 7

Attaching the Toys

+

–

Batteries

Remove screw from battery door.

Replace screw

J> ^

after batteries have

been replaced. DO NOT OVERTIGHTEN.

Assembling the Art Table

STAGE 2STAGE 2

1. Remove Base

H

from bottom of

ExerSaucer.

Note: Remove all toys from ExerSaucer

before assembling the Art Table.

2. Turn ExerSaucer upside down.

3. Remove Bounce Ring

D> !

from Tray.

Push tab

D> @

until it releases from Tray.

Repeat until all six tabs are released

from Tray.

To secure Spin-Loc toys on ExerSaucer

Tray, set toys on Tray and twist toy base

J> #

,

clockwise as shown. Pull up on toys to make

sure they are locked in place.

To remove Spin-Loc toys from Tray, twist toy

base counterclockwise, squeeze tabs

J> $

and

lift, as shown.

If Spin-Loc toy does not stay attached, clean

suction cup per cleaning instructions for

plastic parts on page 9.

Secure Spin-Loc™ toys every time the

ExerSaucer is used.

To place toy with cap on ExerSaucer, set

toy cap

J> !

on top of Leg, as shown. Push

down until tab

J> @

rests in dimple

A> !

on

Leg to ensure toy is attached properly.

To remove toy from ExerSaucer, grab cap

and pull straight up.

To remove batteries from mirror toy,

remove two screws

J> %

, and lift mirror face.

To replace mirror face, replace screws.

DO NOT OVERTIGHTEN.

J> !

J> @

A> !

J> #

J> $

H

D> @

D> !

WARNING

Stage 2 is for use by children who can walk unassisted

up to approximately 48 months.

Stage 2 Art Table MUST be in highest position at all times.

WARNING

Toys with cap MUST be in place

when Stage 1 is in use.

WARNING

J> %

Refer to battery door

for quantity and size

of batteries.

J> ^

8 9

For Plastic Parts:

Wipe surface clean with cloth slightly moistened with mild soap and water.

DO NOT use abrasive cleaners or solvents. Allow to air dry.

For Wood Parts:

Wipe surface clean with cloth slightly moistened with mild soap and water.

DO NOT use abrasive cleaners or solvents. Immediately wipe dry with clean cloth.

For Seat Pad:

Machine Wash Separately, Cold Water – Delicate Cycle. NO CHLORINE BLEACH.

Tumble Dry: 10 – 15 Minutes on Low Heat – Remove Immediately.

If musical toys fail to operate, check the batteries. Note: ONLY the batteries are

replaceable. Dispose of old batteries safely.

DO NOT use this product if any parts are missing, damaged or broken.

Care and Maintenance

BATTERY INFORMATION:

Battery life varies with use.

BATTERY SAFETY INFORMATION: Batteries are small objects. Batteries must be

replaced by adults. Follow the polarity (+/-) diagram in the battery compartment.

• DO NOT mix old and new batteries.

• DO NOT mix alkaline, standard (carbon-zinc), or rechargeable (nickel-

cadmium) batteries.

• Only batteries of the same or equivalent type, as recommended, are to be

used.

• DO NOT dispose of batteries in fire, as batteries may explode or leak.

• The supply terminals are not to be short-circuited.

• DO NOT use rechargeable batteries.

• DO NOT recharge non-rechargeable batteries.

• Promptly remove exhausted batteries from the toy.

• Remove batteries before storing unit for a prolonged period of time.

• DO NOT allow unit to get wet.

• Dispose of used batteries properly.

Battery Replacement: To replace batteries, loosen screw and remove battery door.

Discard old batteries properly and replace with alkaline batteries. Replace door and

tighten screw.

Troubleshooting:

Toy does not turn on or does not respond.

• Make sure batteries are installed correctly.

• Make sure battery cover is correctly secured.

• Install new batteries.

Toy makes improper responses.

• Check or install new batteries.

• Power Off then Power On, to reset.

WARNING

Assembling the Art Table

5. Place Base

H

in opening on

ExerSaucer Tray, as shown.

6. Base Cap

I

can be placed in Tray

with rim facing up, as shown, to create

storage area for supplies.

H

4. Turn the ExerSaucer right-side-up.

10 11

Limited Warranty

For Australian Consumers - CNP Brands Standard Warranty

For Australian Consumers - CNP Brands Standard Warranty - cont.

For a period of 90 days from the original purchase of this Product, Evenflo warrants

to the original end user (“Purchaser”) this Product (including any accessories) against

defects in material or workmanship. Evenflo’s sole obligation under this express

limited warranty shall be, at Evenflo’s option, to repair or replace any Product that

is determined to be defective by Evenflo and determined to be covered by this

warranty.

Repair or replacement as provided under this warranty is the exclusive remedy of

the Purchaser. Proof of purchase in the form of a receipted invoice or bill of sale

evidencing that the Product is within the warranty period must be presented to obtain

warranty service. This express limited warranty is extended by Evenflo ONLY to the

original Purchaser of the Product and is not assignable or transferable to subsequent

purchasers or end users of the Product. For warranty service, contact Evenflo’s

ParentLink Consumer Resource Center at (800) 233-5921 or

www.evenflo.com.

EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

ON THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO SHALL NOT BE LIABLE

FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES

OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED WARRANTY ON THIS

PRODUCT, OR ANY WARRANTY IMPLIED BY OPERATION OF LAW. OTHER THAN

THE EXPRESS LIMITED WARRANTY SET FORTH ABOVE, THERE ARE NO OTHER

WARRANTIES THAT ACCOMPANY THIS PRODUCT AND ANY ORAL, WRITTEN OR

ANY OTHER EXPRESS REPRESENTATION OF ANY KIND IS HEREBY DISCLAIMED.

1.4 CNP Brands agrees to repair or replace at CNP Brands cost, the product, and any accessory supplied

with the product, which is proven upon inspection by CNP Brands or a CNP Brands Authorised Service

Agent not to comply with either warranty contained in clause 1.3. Any decision to repair or replace a

product is to be made by CNP in its absolute discretion. The extent of any repair will be to rectify any

defect in workmanship and materials or to ensure that the product complies with the manufacturer’s

specifications.

1.5 To make a claim under this Standard Warranty you will need to:

a) Return the product within the Warranty Term to the place of purchase together with your proof of

purchase, where the retailer will provide you with assistance to make your claim; or

b) Contact CNP Brands Customer Care Centre on toll free 1300 667 137 during the Warranty Term to

register your claim and provide the details to enable CNP Brands to assess the claim.

1.6 You may also be required to make the product available to CNP Brands or a CNP Brands Authorised

Service Agent. If you are required to return the product to a CNP Brands Authorised Service Agent, CNP

Brands will provide details of the centre closest to you. Unless CNP Brands decides otherwise you are

responsible for any costs associated with returning the product to CNP Brands. The product will be at

your risk whilst in transit to and from the CNP Brands or CNP Brands Authorised Service Agent, unless

transported by CNP Brands or its agents.

1.7 In order for your claim to be processed you will need to provide to CNP Brands with an original proof

of purchase. For example an original retailer purchase receipt, bill of sale, invoice, lay-by docket, credit

card receipt or similar proof of purchase.

1.8 If CNP Brands decide to repair a product, this product may be replaced by refurbished products

of the same type rather than being repaired. Refurbished parts may be used to repair the product.

Replacement of the product or a part does not extend or restart the Warranty Term.

1.9 Exclusions

a) This Standard Warranty does not cover products purchased as an ex-display, without being checked

by CNP Brands or CNP Brands Authorised Service Agents.

b) This Standard Warranty does not cover faults or defects caused by:

i. Unsuitable, improper use or use not in accordance with the manufactures specifications;

ii. Incorrect installation or installation not in accordance with instructions provided;

iii. Normal wear and tear;

iv. Inadequate or complete lack of maintenance;

v. Chemical, electrochemical or electrical influences; or

vi. Harsh detergents or abrasive cleaners used on product finishes.

c) To the fullest extent permitted by law, CNP Brands excludes all liability for damage or injury to any

person, damage to any property, and any indirect consequential or other loss or damage.

To contact CNP Brands or, to find the nearest CNP Brands Authorised Service Agent, please contact

CNP Brands on 1300 667 137, email [email protected] or write to CNP Brands, P.O Box 8 Deer

Park Victoria 3023 Australia. Please also refer to our website www.cnpbrands.com.au.

1.1 Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major failure and compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if goods fail to

be of acceptable quality and the failure does not amount to a major failure.

1.2 In addition to the guarantees that cannot be excluded under the Australian Consumer Law described

in clause 1.1 and any other guarantee or warranty implied by law, when you purchase one of our products,

you will also have the peace of mind in knowing that your product is covered by CNP Brands Standard

Warranty. The Standard Warranty is provided by C.O. White Pty Ltd trading as CNP Brands (ABN 97

004 169 233) (“CNP Brands”). The terms and conditions of the Standard Warranty are further described

below.

1.3 Subject to clause 1.1 and the terms below, CNP Brands warrants that this CNP Brand product,

purchased by you in Australia or New Zealand:

a) is free from defects in workmanship and material, when the product is used for normal consumer

use for a period of 90 DAYS from the date of purchase as evidenced by your proof of purchase

(“Warranty Term”); and

b) will, when the product is used for normal consumer use, comply with the manufacturer’s

specifications during the Warranty Term.

12 13

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

Note: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio TV technician for help.

• This Class B digital apparatus complies with Canadian ICES-003.

WARNING

• www.evenflo.com • USA: 1-800-233-5921, 8 AM – 5PM E.T.

• Canada: 1-937-773-3971 • México: 01-800-706-12-00

Page is loading ...

Evenflo 2-in-1 Activity Center and Art Table User manual

Evenflo 2-in-1 Activity Center and Art Table User manual

in other languages

Related papers

Other documents