Watts pure H2O WH-VIH1-SED-A-WHT-HSG Installation guide

Brand: Watts

Model: pure H2O WH-VIH1-SED-A-WHT-HSG

Category: Sanitary ware

Type: Installation guide

This manual is also suitable for

Pure H2O

Installation, Operation and

Maintenance Manual

WHOLE HOUSE

10" Standard Valve-In-Head Filtration Kit

Model:

WH-VIH1-SED-A-WHT-HSG

WARNING

Please read carefully before proceeding

with installation.

Your failure to follow any attached instructions

or operating parameters may lead to the

product’s failure.

Keep this Manual for future reference.

Do not use with water that is microbiologically unsafe or of un-

known quality without adequate disinfection before or after

the system.

WARNING

If you are unsure about installing your Watts Pure H2O water

filter, contact a Watts Pure H2O representative or consult a

professional plumber.

Failure to install the system correctly voids the warranty. Handle

all components of the system with care. Do not drop, drag or

turn components upside down. Be sure the floor under the

water filter system is clean, level and strong enough to support

the unit.

Refer to enclosed warranty for operating parameters to ensure

proper use with your water supply.

WH-VIH1-SED-A-WHT-HSG

Test the water periodically to verify that the system is

performing satisfactorily. Discard small parts remaining after

the installation.

CAUTION

Table of Contents Pages

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Before Installation

Operational Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contents of Whole House Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Tools Recommended For Installation . . . . . . . . . . . . . . . . . . . . . . . . 2

Prior to Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation

Step 1. Whole House Filter Installation. . . . . . . . . . . . . . . . . . . . . . . . 2

Operation

Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Maintenance & Registration

Suggested Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Filter Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Product Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Technical & Warranty Information

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

IMPORTANT

NOTICE

IOM-WQ-WH-VIH1-SED-A-WHT-HSG

MAXIMUM MINIMUM

Operating Temperature: 100°F (37.8°C) 40°F (4.4°C)

Operating Pressure: 100 psi (7.03 kg/cm²) 20 psi (1.40 kg/cm²)

Introduction

Thank you for your purchase of a Watts Pure H2O Whole House

Water Filter. Water quality concerns are quickly becoming more of a

focus for the public. This Watts Pure H2O whole house water ﬁlter

has been designed and tested to provide you with a higher quality

of water.

This ﬁlter is designed to reduce the amount of sediment that would

normally enter your home water system. Reducing the amount of

sediment in your home water system will allow your ﬁxtures and

water use appliances to work better.

It is important to change out your ﬁlters at the recommended inter-

vals as indicated in this system manual. When replacing the ﬁlter

elements, pay special attention to any cleaning instructions. Should

you have any further questions please refer to our web site at

www.watts.com/pureh2o or call our customer service department

at 1-978-689-6066.

Contents of Whole House Filter

Please make sure all of the items listed below are contained in the

box. If any of the items are missing please contact Watts Pure H2O

at 1-978-689-6066 prior to installing.

• Filter housing with built-in By-Pass Valve

• (3) 50 Micron Sediment Filters (One Preinstalled)

• Filter Wrench

• Mounting Bracket

• Whole House Filter Manual

Tools Recommended For Installation

• Hacksaw or Pipe Cutter

• Low Grit Sandpaper

• (2) 3/4" or 1/2" Crescent Wrenches

• Plumber’s Tape (also known as Thread Seal Tape)

Prior To Installation

Watts Pure H2O’s Whole house ﬁlter is designed to be installed on

the main waterline servicing the house. It should be installed indoors

where it is not subject to cold temperatures or long term exposure

to direct sunlight. Watts Pure H2O does not take any responsibility

for the plumbing of the system into the water line. All water ﬁltration

systems must be installed in accordance with local plumbing codes

and regulations.

Note: For installation, you will need to purchase ﬁttings based on

the pipe size and material of the incoming water line that you will be

tapping into.

Whole House Filter Installation

Step 1 - Determine placement of the unit. Make sure the installation

location allows for easy servicing of the system, including a

clearance beneath the ﬁlter bowl for ﬁlter changes.

Step 2 – Shut off main water supply and open a faucet beyond the

connection to relieve water pressure. Then close the faucet

when depressurized.

Step 3 – Make sure water ﬂow direction coincides with the “IN” and

“OUT” ports marked on the unit.

Step 4 – Cut the water line where the Whole House Filter is to be

installed. The amount of pipe to be removed will be depen-

dent on the type of ﬁttings used. Copper pipes need to be

cleaned & de-burred of any imperfections.

Step 5 – Using the ﬁttings previously purchased, make sure that the

ﬂow direction is correct through the ﬁlter system and plumb

the system to the waterline.

For copper pipes we recommend using brass 3/4" MPT

x plumbing size (1/2" or 3/4") compression style fittings.

For all other material types, check with your plumbing

professional.

Make sure not to overtighten threaded port to the unit!

CAUTION

Operational Paramaters

NOTICE

This unit must be installed vertically with the lid on top.

NOTICE

If pipes will be sweat soldered, do not connect into the unit

until the pipes have cooled. Make sure to use Teflon tape on

all male pipe threading used.

NOTICE

Figure 1: There are several ways to plumb your Whole House Filter into your existing water line.

The diagram above is the basic install layout.

Start Up

Step 1 – Make sure the valve on the lid is turned to “FLOW”.

Step 2 – Open a faucet downstream of the Whole House ﬁlter unit.

Step 3 – Slowly turn on main water supply until faucet downstream

is steadily ﬂowing.

Step 4 – Turn off faucet and check for leaks at your connections.

Monitor for leaks for 24 hours after installation.

Operating Instructions

This whole-house ﬁlter features a Valve-In-Head design. This

allows you to control water ﬂow through the unit without

additional hardware.

VALVE OPERATION

(SEE LABEL FOR POSITION)

BY-PASS Allows water to continue to flow through the house NOT utilizing the filter.

OFF Shuts off water before the filter.

FLOW Allows water through the house utilizing the filter.

Note: In all three modes the unit will remain under pressure.

Suggested Maintenance

This whole house ﬁlter can use 5, 10, 20, or 50 micron sediment

ﬁlters. This kit includes three (3) 50 micron ﬁlters. The recommended

ﬁlter is a 50 micron. The recommended time for replacing your ﬁlter

is every three (3) to six (6) months depending on your incoming

water conditions. If your water contains more sediment you may be

required to change your ﬁlters more often. Failure to change ﬁlters

regularly will reduce water pressure & ﬂow. Periodically check ﬁlter

for sediment or dirt loading.

Filter Replacement

Step 1 – Shut off the water to the ﬁlter housing by turning the

bypass valve to “BYPASS” or “OFF”.

Step 2 – The bowl of the system can be removed by turning it

clockwise (see Figure 1). Use the supplied ﬁlter wrench to

loosen the housing.

Step 3 – Remove the old ﬁlter and discard.

Step 4 – Clean the ﬁlter housing with a mild soap solution and

rinse with water. Check O-ring and lubricate with water

soluble lubricant.

Step 5 – Replace ﬁlter.

Step 6 – Reinstall by turning the ﬁlter bowl counter-clockwise (see

Figure 1) onto the lid. Make sure O-ring is properly seated.

Step 7 – Turn bypass valve back to “FLOW”.

Step 8 – Check for leaks. Monitor unit for leaks for 24 hours after

ﬁlter replacement.

Product Registration

To register your product, please visit www.watts.com/pureh2o and

select “Register Now”. Watts Pure H2O is concerned for the safety

of your personal information. Watts Pure H2O collects personal

information when you register with Watts Pure H2O. This information

is stored in our data base and we do not rent, sell, or share personal

information with other people or nonafﬁliated companies.

We reserve the right to send you certain types of communications

such as direct mail, email, or by telephone relating to our products

or products that you have purchased. We limit access to your per-

sonal information to those employees who will directly provide you

with services or products in order to do their jobs.

Petroleum based lubricants (such as Vaseline®) must not

be used.

NOTICE

Hand tighten housing. Wrench should only be used to

loosen housing.

NOTICE

PROBLEM CAUSE SOLUTION

1. Filter bowl has no water in it Water is not turned on at Main Check that the water is on at Main

Valve turned to “BY-PASS” or “OFF” Make sure valve is turned to the “FLOW” position

2. Leaking at the bowl O-Ring kinked or not seated Check / Replace / Re-seat O-Ring

Bowl not tightened enough Tighten bowl

3. Leaking at the valve fittings Improper installation / Not enough plumber’s tape on fitting Replace or repair fittings

4. Leaking at top of valve (lid) Faulty lid Call Watts Pure H2O at 1-978-689-6066 for a replacement

5. Low water flow / pressure Filter clogged Replace filter

Troubleshooting

Limited Warranty

WHAT YOUR WARRANTY COVERS:

Watts warrants your product (excluding replaceable filters) to be free from defects in material and workmanship under normal usage for a period of

one year from the date of original purchase. If any part of this system is found to be defective within the warranty period, return the system after

obtaining a return authorization from Watts (see below), and Watts will repair, or at Watts’ option, replace the system at no charge.

HOW TO OBTAIN WARRANTY SERVICE:

To obtain warranty service, call 888-321-0500 for a return authorization number. Then, ship your system to our factory, freight and insurance

prepaid, with proof of the date of original purchase. Please include a note stating the warranty problem. Watts will repair, or at Watts’ option,

replace the system and ship it back to you at no charge.

WHAT THIS WARRANTY DOES NOT COVER:

This warranty does not cover defects resulting from improper installation (installation contrary to Watts printed instructions), abuse, misuse,

misapplication, improper maintenance, neglect, alteration, accidents, casualties, fire, flood, freezing, environmental factors, water pressure spikes,

adverse water conditions or other events or conditions beyond Watts’ control.

This warranty will be void if defects occur due to failure to observe the following conditions:

1. The system must be hooked up to a potable municipal or well cold water supply.

2. The pH of the water must not be lower than 5 or higher than 10.

3. The incoming water pressure must be between 20 and 100 pounds per square inch (1.41 - 7.03 kilograms per square centimeter).

4. Incoming water to the system cannot exceed 100 degrees F (38 degrees C.)

This warranty does not cover any equipment that is relocated from the site of its original installation.

This warranty does not cover any charges incurred due to professional installation.

OTHER CONDITIONS:

If Watts chooses to replace the system, Watts may replace it with reconditioned equipment. Parts used in repairing or replacing the system will

be warranted for 90 days from the date the system is returned to you or for the remainder of the system’s original warranty period, whichever is

longer. This warranty is not assignable or transferable.

LIMITATIONS AND EXCLUSIONS:

THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY WATTS WITH RESPECT TO THE SYSTEM. WATTS

MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. WATTS HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The warranty remedy described

above shall constitute the sole and exclusive remedy for breach of warranty, and Watts shall not be responsible for an incidental or consequential

damages, including travel expense, telephone charges, loss of revenue or profits, loss of time, inconvenience, loss of use of the equipment, or loss

or damage caused by this system and its failure to function properly. This warranty sets forth all of Watts responsibilities regarding this system.

YOUR RIGHTS UNDER STATE LAW:

Some states do not allow the exclusion or limitation of incidental or consequential damages and some states do not allow limitations on how

long implied warranties may last. Therefore, the above limitations or exclusions may not apply to you. This warranty gives you specific legal

rights and you may also have other rights, which vary from state to state. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED

WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE.

USA: T: (888) 321-0500 • F: (678) 355-0590 • N. Andover, MA 01845 • Watts.com

Canada: T: (888) 208-8927 • F: (905) 332-7068 • Burlington, ON M5J3G6 • Watts.ca

Latin America: T: (52) 55 4122 0138 • Watts.com

Page is loading ...

Watts pure H2O WH-VIH1-SED-A-WHT-HSG Installation guide

Brand: Watts

Model: pure H2O WH-VIH1-SED-A-WHT-HSG

Category: Sanitary ware

Type: Installation guide

This manual is also suitable for

Pure H2O

Download PDF

report

in other languages

français: Watts pure H2O WH-VIH1-SED-A-WHT-HSG Guide d'installation
español: Watts pure H2O WH-VIH1-SED-A-WHT-HSG Guía de instalación

Watts pure H2O WH-VIH1-SED-A-WHT-HSG Installation guide

This manual is also suitable for

Watts pure H2O WH-VIH1-SED-A-WHT-HSG Installation guide

in other languages

Related papers

Other documents