AcuityBrands ESL2 User manual

LED IMPORTANT SAFETY INSTRUCTIONS

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and

other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

• Installation and service of luminaires should be performed by a qualified licensed electrician.

• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation

and any hazards involved. Regular fixture maintenance programs are recommended.

• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient

dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm

water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly

become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been

damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.

• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.

• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency

to meet in connection with installation, operation, or maintenance. Should further information be desired or should

particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be

referred to Acuity Brands Lighting, Inc.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

 Disconnect or turn off power before

installation or servicing.

 Verify that supply voltage is correct by

comparing it with the luminaire label

information.

 Make all electrical and grounded

connections in accordance with the National

Electrical Code (NEC) and any applicable

local code requirements.

 All wiring connections should be capped

with UL approved recognized wire

connectors.

WARNING

RISK OF ELECTRIC SHOCK

 Allow lamp/fixture to cool before handling.

Do not touch enclosure or light source.

 Do not exceed maximum wattage marked on

luminaire label.

 Follow all manufacturer’s warnings,

recommendations and restrictions for: driver

type, burning position, mounting

locations/methods, replacement and

recycling.

WARNING

RISK OF BURN

 Wear gloves and safety glasses at all times

when removing luminaire from carton,

installing, servicing or performing

maintenance.

 Avoid direct eye exposure to the light source

while it is on.

CAUTION

RISK OF INJURY

 Keep combustible and other materials that

can burn, away from lamp/lens.

 Do not operate in close proximity to persons,

combustible materials or substances

affected by heat or drying.

CAUTION

RISK OF FIRE

DISCONTINUED

IM-396

LED IMPORTANT SAFETY INSTRUCTIONS

Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory

statements.

Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and

Conditions, please visit www.acuitybrands.com.

Our Brands Indoor/Outdoor Indoor Lighting Outdoor Lighting Controls

Lithonia Lighting Gotham American Electric Lighting DARK TO LIGHT

Carandini Mark Architectural Lighting Antique Street Lamps Lighting Control & Design

Holophane Peerless Hydrel ROAM

RELOC Renaissance Lighting Tersen Sensor Switch

Winona Lighting Synergy

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products.

ABL LED General Warnings, Form No. 503.203

 Never connect components under load.

 Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire

insulation.

 Unless individual product specifications deem otherwise: Never connect an LED product directly to a

dimmer packs, occupancy sensors, timing devices, or other related control devices. LED fixtures must be

powered directly off a switched circuit.

 Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for

some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other

material that will prevent convection or conduction cooling.

 Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient

temperature.

 Only use fixture in its intended location.

 LED products are Polarity Sensitive. Ensure proper Polarity before installation.

 Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be

worn during all installation or servicing of the unit.

 Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter

performance.

 Some components inside the fixture may not be serviceable. In the unlikely event your unit may require

service, stop using the unit immediately and contact an ABL representative for assistance.

 Always read the fixtures complete installation instructions prior to installation for any additional fixture

specific warnings.

CAUTION: RISK OF PRODUCT DAMAGE

DISCONTINUED

HOLOPHANE® Installation and

Tear Drop Utility LED Luminaire Series Maintenance

(ESL3 & MPL3) Manual

IM-396

AFTER INSTALLATION DELIVER THIS MANUAL TO OWNER

GR2419

IMPORTANT SAFETY INSTRUCTIONS

WARNING – READ THESE INSTRUCTIONS

CAREFULLY BEFORE ATTEMPTING TO INSTALL OR

MAINTAIN THIS FIXTURE. WORK MUST BE DONE BY

QUALIFIED PERSONNEL.

WARNING – BE CERTAIN THAT ALL ELECTRICAL

POWER IS DISCONNECTED FROM THE FIXTURE

BEFORE INSTALLING OR MAINTAINING THE FIXTURE.

WARNING – FOLLOW LAMP MANUFACTURER’S

OPERATING AND MAINTENANCE INSTRUCTIONS.

FAILURE TO FOLLOW THESE WARNINGS

MAY RESULT IN DEATH, INJURY OR SIGNIFICANT

PROPERTY DAMAGE.

1 INTRODUCTION

1.1 Product Description.

• This fixture is designed to operate an LED light source at up to

245 watts.

• This fixture must be serviced by trained electrical personnel.

• This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

1.2 Alternate Information Sources.

Holophane

Field Service Department

P.O. Box 3004

Newark, OH 43058-3004

(740) 349-4182

ESL3

MPL3

DISCONTINUED

IM-396

2 INSTALLATION

2.1 Tools and Materials Required

DESCRIPTION USE

Flat blade screwdriver Terminal block connections

Pendant Mount:

3/16” Allen wrench Setscrew

Pipe Thread Sealant Mounting pipe threads

Stem Mount:

1/8" Allen wrench Setscrew

3/16” Allen wrench Setscrew

1/4” Allen wrench Setscrew

9/16” Socket Nuts

3/8” Socket Screws

2.2 Fixture Installation.

2.2.1 Remove the mounting assembly from the electrical housing

by releasing the latch and then swinging it open until the hinge

disengages. See Figure 1.

2.2.2 Loosen the wire chamber cover screws and remove the

wiring chamber cover. Allow it to hang by the electrical wires

attached to the terminal block. See Figure 1.

Figure 1

GR1492

2.2.3 Pendant mount

This unit must be mounted to a 1-1/2 NPT male threaded pendant.

Verify that the set screw, located in the mounting assembly, is

backed out enough that it will not interfere with the mounting

threads. See Figure 1. Thoroughly inspect threads for damage.

DO NOT attempt to assemble with another part if any thread

damage is found on either part. Apply pipe thread sealant

completely around the first 4 male threads on the mounting

pendant. Force the sealant into the threads, see Figure 2.

Thread the mounting assembly onto the pipe threads. Tighten by

hand at least 5 full turns to ensure the end of the conduit goes past

the setscrew hole.

Figure 2

GR1060

CAUTION

FIELD APPLICATION OF PIPE THREAD SEALANT IS

REQUIRED. FAILURE TO PROPERLY APPLY PIPE THREAD

SEALANT COULD CAUSE THIS UNIT TO LEAK OR CAUSE

INADEQUATE THREAD ENGAGEMENT.

PIPE THREAD SEALANT MUST BE APPLIED TO MALE

THREAD ASSEMBLY TO ENSURE PROPER INSTALLATION

2.2.4 Rigid Pendant mounting - Thread the mounting assembly

onto the pipe threads. Tighten by hand at least 5 full turns to insure

the end of the conduit goes past the setscrew hole. Continue to

tighten with wrench until the threads tighten completely and the

street side of luminaire is pointed in proper direction. Reflector

assembly and refractor are marked "street side."

2.2.5 Tighten the set screw to 12-15 ft-lbs.

2.2.6 Quick Stem Mount

Refer to Installation Manual provided with the swivel fitter (IM-347)

Attach the luminaire to the fitter by removing fitter door and inserting

stem of luminaire into the fitter. (Fig 3) Do not damage the electrical

supply wires during attachment of the luminaire. Feed the electrical

supply wires through the center of the stem grommet and make final

connection per section 2.2.7. Replace the fitter door by engaging

the lip of the door inside the fitter. Tighten the door screws to 5-6 Ft-

lbs. Tighten the nuts on the U-bolts to 30-40 Ft-lbs. Allow luminaire

to self-level and tighten the set screws to 12-15 Ft-lbs. If necessary,

adjust the leveling set screws so that the fitter is installed level.

Install shaft collar on stem in upmost position, flush with fitter.

Figure 3

GR2185

DISCONTINUED

IM-396

2.2.7 Remove wire chamber cover and connect the electrical

supply wires to the terminal block in the back of the electrical

chamber. The terminals are marked "L1" (Line 1). "G" (Ground),

and "L2" (Line 2). If one of the supply lines is electrically neutral, it

should be connected to terminal "L2". (Fig 1) Replace wire

chamber cover.

2.2.8 DM Option For units equipped with 0-10V dimming,

locate the gray and purple leads from the driver module. These are

to be used with a Holophane approved control circuit.

CAUTION

LEADS USED FOR DIMMING CONTROLS ARE TO BE

SEPARATED FROM MAIN POWER CONDUCTORS IN A

MANNER TO SATISFY STATE AND LOCAL CODES.

2.2.9 Hang the electrical assembly on the mounting assembly

hinge and plug in the electrical connector. See Figure 4.

If equipped with a photocontrol receptacle, insert photocell and

position eye towards lens. Swing the electrical assembly closed

and engage the latch to the catch to securely close unit.

2.2.10 Hang the refractor assembly on the door hinge. Swing the

refractor assembly closed, engage the closure bolt and tighten the

wing nut securely. See Figure 5.

2.2.11 If using Flat Glass (FG) Option, REMOVE BLUE FILM

FROM GLASS.

OPTICS ORIENTATION NOTE

The product has a molded-in “STREET SIDE” marking. Insure that

this side is aimed toward the street.

2.2.11 Electrically energize the fixture and check for proper

operation.

Figure 4

GR 2420

Figure 5

GR396

3 MAINTENANCE

3.1 Relamping and Cleaning.

3.1.1 Wipe off exterior dirt and debris.

3.1.2 Loosen the wing nut securing the refractor assembly and

disengage the closure bolt, swinging the refractor open slowly. See

Figure 5.

3.1.3 Inspect the LED board and reflector assembly. These are

maintenance free items and should never be touched, adjusted or

wiped with any cleaner.

3.1.4 Wipe off the refractor and reflector with a dry cloth. If the

refractor needs to be washed, use water and detergent.

CAUTION

DO NOT USE ABRASIVE CLEANSERS ON OPTICAL SURFACES.

THEIR USE MAY RESULT IN THE LOSS OF OPTICAL

PERFORMANCE.

3.1.5 Swing the refractor assembly closed, engage the closure bolt

and tighten the wing nut securely. See Figure 5.

3.2 Electrical Component Replacement.

NOTE

The entire fixture below the mounting assembly (Fig 1.) may be

removed in the field to allow further maintenance of the module to

be performed in the shop.

The fixture contains a surge protection module (Shown in Fig 4) that

is meant to fail in case of electrical spikes or over voltage

conditions. Remove this and replace to see if this restores power to

the circuit.

3.2.1 Disengage the latch securing the fixture to the mounting

assembly and swing the fixture open slowly.

3.2.2 Disconnect the electrical connector and then remove the

fixture from the mounting assembly by swinging the fixture open on

the hinge far enough to disengage the hinge pin from the hinge

hook. See Figure 1.

3.2.3 Remove the electrical module by loosening the two

attachment screws and disengaging the module from the screw

heads and lift the module from the electrical housing. See Figure 1.

3.2.4 Carefully note the position and attachment means for all

components and wiring and tag all wiring that will be disconnected.

Remove the screws, straps and brackets securing the component(s)

and save all mounting hardware for reuse.

DISCONTINUED

IM-396

3.2.5 Replace with Holophane supplied electrical components,

positioning the new component exactly as was the old. Secure with

the original hardware and tighten all fasteners securely.

3.2.6 Rewire based on the tags applied earlier and according to

industry accepted wiring techniques. Reposition all wiring and

secure it as it was originally.

3.2.7 Carefully reinstall the electrical module into the electrical

housing; tighten all screws securely. See Figure 4.

3.2.8 Hang the fixture on the hinge hook of the mounting

assembly and plug in the electrical connector. Swing the electrical

assembly closed and engage the latch to the catch to securely

close unit. See Figure 1.

3.2.9 Electrically energize the fixture and check for proper

operation.

4 Limited Warranty and Limitation of Liability

The Holophane limited warranty and limitation of liability is

published in the "Terms and Conditions" section of the current

Holophane buyer's guide, and is available from your local

Holophane sales representative.

4.1 Failure to properly install this Unit will void all warranties.

5. LIMITED WARRANTY AND

LIMITATION OF LIABILITY

Complete warranty terms located at: www.acuitybrands.com/

support/warranty/terms-and-conditions

6. ADJUSTABLE OUTPUT (AO) TABLES

Field Adjustable Output Module

The Field Adjustable Output (AO) module is an onboard device

that adjusts the light output and input wattage to meet site specific

requirements, allowing a single fixture configuration to be flexibly

applied in many different applications.

P10S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

94%

6

80%

5

68%

4

55%

3

41%

42%

2

28%

29%

1

37%

41%

P15S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

94%

6

80%

5

68%

4

55%

3

42%

2

28%

29%

1

14%

15%

P20S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

94%

6

81%

80%

5

69%

68%

4

56%

54%

3

42%

41%

2

29%

1

14%

15%

P20U: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

94%

6

81%

80%

5

69%

68%

4

56%

55%

3

43%

42%

2

29%

1

15%

DISCONTINUED

IM-396

P25S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

94%

6

81%

80%

5

69%

67%

4

56%

54%

3

43%

41%

2

29%

28%

1

15%

P25U: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

94%

6

81%

80%

5

69%

68%

4

56%

54%

3

43%

41%

2

30%

29%

1

15%

P30S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

94%

6

81%

80%

5

69%

67%

4

56%

54%

3

43%

41%

2

30%

28%

1

15%

P30U: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

94%

6

81%

80%

5

70%

67%

4

57%

54%

3

44%

41%

2

30%

29%

1

15%

P35S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

94%

6

81%

79%

5

70%

67%

4

57%

54%

3

44%

41%

2

30%

28%

1

15%

P40S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

95%

94%

6

82%

79%

5

70%

67%

4

57%

54%

3

44%

41%

2

31%

28%

1

16%

15%

P45S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

95%

94%

6

82%

79%

5

71%

67%

4

58%

54%

3

45%

41%

2

31%

28%

1

16%

14%

P50S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

95%

94%

6

82%

79%

5

71%

67%

4

59%

54%

3

45%

41%

2

32%

28%

1

16%

14%

DISCONTINUED

IM-396

P55S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

95%

94%

6

83%

79%

5

72%

67%

4

59%

54%

3

46%

41%

2

32%

28%

1

17%

14%

P60S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

95%

94%

6

83%

79%

5

72%

67%

4

60%

54%

3

47%

41%

2

33%

28%

1

17%

14%

P65S: MVOLT and HVOLT

AO Position

% Lumens

% Wattage

8

100%

7

95%

94%

6

84%

79%

5

73%

67%

4

61%

53%

3

48%

40%

2

33%

28%

1

18%

14%

®

Acuity Lighting Group, Inc.

3825 Columbus Rd. S.W. Granville, OH 43023

Visit our web site at www.holophane.com

Printed in USA

DISCONTINUED

AcuityBrands ESL2 User manual

AcuityBrands ESL2 User manual

Related papers

Other documents