NAPOLEON W190-0202 allows effortless communication between various devices. Extend the location of your LED and AP buttons and connect third-party devices via the ACC port. The reset button enables rebooting the module.
NAPOLEON W190-0202 allows effortless communication between various devices. Extend the location of your LED and AP buttons and connect third-party devices via the ACC port. The reset button enables rebooting the module.
IoT Module instructions
1. Connect 4p shielded cable to IoT module COM port. And
connect the end of shielded cable to host device COM port.
(Make sure host device COM port VCC is rated for 3.3V). IoT
module will be powered by host device COM port.
2. Connect an extension button cable to AP port if required to
extends AP button location.
3. Connect an extension LED cable to LED port if required to
extends LED location.
4. Connect 4p cable to ACC port if required to communicate
with 3rd device.
5. Reset button can be pressed to reboot IoT module.
Wolf Steel LTD.
FCCCaution
Thisdevicecomplieswithpart15oftheFCCRules.Operationissubjecttothe
followingtwoconditions:(1)Thisdevicemaynotcauseharmfulinterference,and(2)
thisdevicemustacceptanyinterferencereceived,includinginterferencethatmay
causeundesiredoperation.
AnyChangesormodificationsnotexpresslyapprovedbythepartyresponsiblefor
compliancecouldvoidtheuser'sauthoritytooperatetheequipment.
Note: ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClass
Bdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedto
providereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.
Thisequipmentgeneratesusesandcanradiateradiofrequencyenergyand,ifnot
installedandusedinaccordancewiththeinstructions,maycauseharmfulinterference
toradiocommunications.However,thereisnoguaranteethatinterferencewillnot
occurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferenceto
radioortelevisionreception,whichcanbedeterminedbyturningtheequipmentoff
andon,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthe
followingmeasures:
-Reorientorrelocatethereceivingantenna.
-Increasetheseparationbetweentheequipmentandreceiver.
-Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthe
receiverisconnected.
-Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
This equipmentcomplieswithFCC radiation exposure limits setforthforan
uncontrolledenvironment.
IC Caution:
- English:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) This device must accept any interference, including interference that
may cause undesired operation of the device.
- French:
Le présentappareilestconf orme aux CNR d' Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitationestautorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l' utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le
brouillageest susceptible d'encompromettre le fonctionnement.
-
1
-
2
-
3
NAPOLEON W190-0202 allows effortless communication between various devices. Extend the location of your LED and AP buttons and connect third-party devices via the ACC port. The reset button enables rebooting the module.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Texas Instruments CC3120MOD SimpleLink™ Wi-Fi® BoosterPack™ Plug-in Module and IoT Solution User guide
-
Arduino ABX00049 Owner's manual
-
Samsung Electronics WIC212S IoT Module Operating instructions
-
Carrier ML5 Asset Tracker Telematics Module User manual
-
Samsung Electronics WIC213S User manual
-
Cisco IG21 Installation guide
-
Netcomm NTC-140 User guide
-
Dell Edge Gateway 3000 Series OEM Ready User guide
-
Espressif EK058 2.4 GHz WiFi Bluetooth LE Module User manual
-
