tbs electronics OCS 250-70 Owner's manual

Brand: tbs electronics

Model: OCS 250-70

Category: Rechargeable batteries

Type: Owner's manual

MPPT Solar Charge Controller

Omnicharge Solar

OCS 150-60 (150V/60A)

OCS 250-70 (250V/70A)

Installation manual

Installatie handleiding

Installationsanleitung

Manuel d’installation

Manual de instalación

TBS ELECTRONICS BV

De Marowijne 3, 1689AR, Zwaag, The Netherlands

tbs-electronics.com

Notice of Copyright

parties without the express written permission of TBS Electronics BV, De Marowijne 3, 1689AR,

Zwaag, The Netherlands. TBS Electronics BV reserves the right to revise this document and to

periodically make changes to the content hereof without obligation or organization of such revisions

or changes, unless required to do so by prior arrangement.

Exclusions for documentation and product usage

UNLESS SPECIFICALLY AGREED TO IN WRITING, TBS ELECTRONICS BV (“TBS”) :

1. MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY

TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER

DOCUMENTATION

2. ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES,

WHETHER SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT

ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH INFORMATION

WILL BE ENTIRELY AT THE USER’S RISK

3. REMINDS YOU THAT IF THIS MANUAL IS IN ANY LANGUAGE OTHER THAN ENGLISH OR

DUTCH, ALTHOUGH STEPS HAVE BEEN TAKEN TO MAINTAIN THE ACCURACY OF THE

TRANSLATION, THE ACCURACY CANNOT BE GUARANTEED.

4. MAKES NO WARRANTY, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

REGARDING THESE TBS PRODUCTS AND MAKES SUCH TBS PRODUCTS

AVAILABLE SOLELY ON AN “AS IS” BASIS.

5. SHALL IN NO EVENT BE LIABLE TO ANYONE FOR SPECIAL, COLLATERAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR ARISING OUT OF PURCHASE OR

USE OF THESE TBS PRODUCTS. THE SOLE AND EXCLUSIVE LIABILITY TO TBS, REGARDLESS

OF THE FORM OF ACTION, SHALL NOT EXCEED THE PURCHASE PRICE OF THE TBS

PRODUCTS DESCRIBED HERE IN.

Document name, date and part number

“OCS-60-70 Installation Manual Rev1endfs”, August 2023, xxxxxx

English

Page 5

Nederlands

Pagina 18

Deutsch

Seite 31

Francais

Page 44

Español

Página 57

TABLE OF CONTENTS

1. SAFETY PRECAUTIONS ........................................................................................................................ 6

2. INSTALLATION .................................................................................................................................... 8

2.1 Installation precautions ........................................................................................................... 8

2.2 Mounting ................................................................................................................................. 8

2.3 Wiring details .......................................................................................................................... 9

2.3.1 Other connections ............................................................................................................. 11

2.3.2 Detachable display for remote use ................................................................................... 11

3. COMMISSIONING ............................................................................................................................. 12

3.1 Connecting the battery ......................................................................................................... 12

3.2 Battery type selection and solar charger reset ..................................................................... 13

3.3 Connecting the PV panels ..................................................................................................... 14

4. TECHNICAL SPECIFICATIONS ............................................................................................................ 15

5. WARRANTY CONDITIONS ................................................................................................................. 16

6. DECLARATION OF CONFORMITY ...................................................................................................... 17

1. SAFETY PRECAUTIONS

Thank you for purchasing a TBS Electronics (TBS) Omnicharge Solar MPPT Solar Charge Controller

(hereinafter referred to as 'product' or ‘solar charger’). Please read this installation manual for

information about installing the product correctly and safely. Keep this installation manual and all

other included documentation close to the product for future reference. For the most recent manual

revision, please check the downloads section of our website.

The installation instructions are intended for installers that should have knowledge and experience

in installing electrical equipment, knowledge of the applicable installation codes, and awareness of

the hazards involved in performing electrical work and how to reduce those hazards.

This chapter contains important safety information for this product. READ ALL instructions and

cautionary markings on or provided with this product, and all appropriate sections of this guide. This

product contains no user serviceable parts. Opening up the product will void product warranty.

GENERAL WARNINGS

• Do not cover or obstruct any air vent openings and/or install in a zero clearance

compartment. Ensure that there is always sufficient free space around the product

for ventilation.

• Shock hazard! Solar panel arrays may generate dangerously high open circuit

voltages.

• Avoid moisture ingress. Never expose the unit to snow, water, etc.

• Explosion hazard! Do not use this product in the vicinity of flammable fumes or

gases.

• After unpacking, check if the product shows any mechanical damage. Never use

the product when the enclosure shows any visual damage caused by harsh

handling, or when it has been dropped accidentally. Contact your local supplier for

further information.

• Do not mount this product in a publicly accessible area. Keep away from children!

• When installing or servicing this product, always make sure that the solar panel

input is de-energized by either opening the advised double pole circuit breaker in

the PV line or by protecting the solar panels from light by covering these.

• Never touch uninsulated wire ends and always use insulated tools during

installation and servicing of this product.

• Please use this product for the designated application only

BATTERY WARNINGS

• When working with electrical equipment or lead acid batteries, have someone

nearby in case of an emergency.

• Study and follow all the battery manufacturer’s specific precautions when

installing, using and servicing the battery connected to the charger.

• Wear eye protection and gloves.

• Avoid touching your eyes while using this unit.

• Keep fresh water and soap on hand in the event battery acid comes in contact with

eyes. If this occurs, clean right away with soap and water for a minimum of 15

minutes and seek medical attention.

• Batteries can produce explosive gases. DO NOT smoke or have an open spark or

fire near the system.

• Never attempt to re-charge a damaged, frozen or non-rechargeable battery.

• Avoid dropping any metal tool or object on the battery. Doing so could create a

spark or short circuit which goes through the battery or another electrical tool that

may create an explosion.

CAUTION

LIMITATIONS OF USE

Do not use in connection with life support systems or other medical equipment or devices.

This battery charger is not to be used by persons with reduced physical or mental

capabilities or lack of knowledge and experience. Not to be operated or used by children.

2. INSTALLATION

2.1 Installation precautions

WARNING

• The PV (solar panel) input of this product is not isolated from the battery output.

Therefore the PV-, battery- and control circuits are considered hazardous and

should not be user accessible.

• Keep at least 15cm of clear space available above and below the product

• Always protect the PV and battery connections against inadvertent contact. Install

the product in a well ventilated enclosure or provide other means of protection.

• Always use flexible multistranded copper cables for the PV and battery

connections. Using cables with a too low strand count will result in a higher contact

resistance which eventually may result in fire hazards.

• Always provide a means of strain relief for all connected cables, in order to limit

the amount of mechanical stress to the connections

• Make sure that the ambient temperature is between -35°C and +60°C. Above

+45°C the solar charger will automatically derate the output power. Do not expose

the charger to any heat source (such as direct sunlight or heating). Also avoid

charger exposure to excessive vibrations.

2.2 Mounting

Please see the image below for the basic mounting instructions:

Always mount the Solar charger in the

orientation as shown on the left

(connections pointing downwards). When

mounted otherwise, proper functionality

and safety cannot be guaranteed.

2.3 Wiring details

WARNING

• For user safety during installation, please make sure that the output of the supplying

PV source is switched off (open circuit breaker in the PV supply lines or protect the

solar panels from light by covering these). Also remove the fuse from the output

battery positive line.

• The wiring example in this chapter is primarily intended as a functional one. Always

check your local regulations, codes and requirements for installing a solar charger.

• Make sure that all PV and battery screw terminal connections are strongly tightened

(2 – 2.5Nm)

• For detailed PV and solar charger grounding schemes and ground fault detection

implementation, please follow your local electrical regulations.

CAUTION

• To avoid solar charger damage, please check if the maximum open circuit voltage

(Voc) of a series string of PV panels, does not exceed the maximum input voltage of

the solar charger. Please take into account that Voc increases as the temperature

decreases. Typically, Voc is 10% higher at 0°C compared to the often rated 25°C

value. It can even rise to +25% at extremely low temperatures down to -40°C.

• Please double check if the battery voltage matches the specifications of the used

charger model

• Please double check the polarity of the PV source as well as the battery. Long term

reverse connection of the battery, may damage the solar charger.

• Ground the frames and mounting racks of your PV panels to reduce the chance of

lightning damage. Do not connect the positive or negative PV wires to ground.

The image below shows a general wiring example of the solar charger. The main PV and battery

connections are indicated by a number (1 to 4). It is very important to exactly follow this wiring order

to avoid solar charger and/or battery damage. The wiring order is:

1. Battery positive cable

2. Battery negative cable

Then wait 3 seconds for proper automatic battery voltage detection (see chapter 3.1)

3. PV positive cable1)

4. PV negative cable1)

1) When a double pole switch is installed in the PV lines, both positive and negative cables are of

course allowed to be switched on simultaneously.

Notes:

• The solar charger can be installed in a positive or in a negative grounded system. In a vehicle

for example, always apply a short single ground connection, ideally close to the battery, to

avoid ground loops that could cause system instabilities.

• Please check the table below for maximum PV and battery current levels plus advised

minimum cable sizes:

Charger

model

PV max. input

current

Min.PV wire

size

Battery max.

charge current

Min. battery

wire size

OCS 150-60

50A

16mm2

60A

16mm2

OCS 250-70

40A

10mm2

70A

16mm2

• Please check the next table for battery fuse recommendations:

Charger model

Min. fuse rating

Max. fuse rating

OCS 150-60

70A

85A

OCS 250-70

85A

100A

• When the battery temperature sensor is connected to the solar charger to enable

temperature compensated charging, please make sure that this sensor is located as close as

possible to the battery. When no temperature sensor is connected to the solar charger,

charge voltages will not be compensated against varying temperature.

2.3.1 Other connections

The solar chargers are equipped with a few additional in- and outputs, plus an internal setup button.

Please see below for the locations and further information:

1. Intended for future use. Do not connect to any accessory or other device.

2. Expansion port, intended for future use. Do not connect to any accessory or other device.

3. Battery temperature sensor connector.

4. Intended for future use. Do not connect to any accessory or other device.

5. Connector for internal alarm relay. Please see below the contact order:

The alarm relay will be triggered (C connects to NO) when a

battery under- or overvoltage limit has been exceeded. When the

battery voltage is in normal range, the relay contacts are in the

position as indicated on the left (C connects to NC). The relay

contact specifications are 10A @ 230Vac or 30Vdc.

6. Setup button. This button can be used to select a different battery type, or to reset the solar

charger back to factory default settings.

2.3.2 Detachable display for remote use

The display module attached to the front panel can be detached easily by removing the two screws.

This allows the display module to act as a wired remote control. The interconnection cable between

the solar charger and the display module is a straight wired (1:1) 9 pole DSUB9 male to DSUB9

female cable. This is a standard serial communication cable that is widely available. The maximum

advised cable length is 10 meter.

3. COMMISSIONING

3.1 Connecting the battery

As explained in chapter 2.3, it is important to first connect the battery to the solar charger by placing

the battery fuse or close the circuit breaker. When the battery is connected, the solar charger will

automatically detect the battery’s nominal voltage. After this, the battery status and battery type

LEDs will be lit.

The battery status LED globally indicates the battery’s condition. It can light in the following colors:

Battery status LED color

Indicator mode

Battery status

Green

Continuous

Battery full

Yellow

Continuous

Battery normal

Red

Continuous

Battery voltage below undervoltage alarm

value

Quickly flashing

Battery undervoltage, overvoltage or

overtemperature alarm

The battery type LED indicates the selected battery type and its corresponding charge program. The

factory default battery type setting is ‘AGM (sealed)’ which corresponds to a green battery type LED.

The following alternative battery types are available:

Battery type LED color

Selected battery type

Red

Flooded (FLD) 1)

Yellow

GEL1)

Green

AGM (SLD) 1)

Blue

LiFePo4 (12V)2)

Purple

LiFePo4 (24V)2)

Orange

LiFePo4 (36V)2)

Cyan

LiFePo4 (48V)2)

White

Custom (user programmable)3)

1) For lead based batteries, the nominal voltage will be detected automatically

2) For LiFePo4 batteries, the nominal voltage has to be selected manually

3) The factory default parameters for the ‘Custom’ battery type are the same as the ‘AGM

(Sealed)’ battery type

Please see the table below for an overview of the main factory default parameter values of each

battery type:

Battery type1)

Parameter

AGM (SLD)

GEL

Flooded (FLD)

Lithium /

LiFePo4 (LI)

Charge Voltage

14.6V

14.2V

14.4V

Absorption Time

120 minutes

Float Voltage

13.6V

13.4V

Restart Voltage

13.2V

Auto Equalize

Charge

30 days

Equalize Voltage

14.8V

Equalize Duration

120 minutes

Temperature

Compensation

-3mV/°C/cell

Overvoltage

Alarm

16.0V

Undervoltage

Alarm On Value

11.6V

12.0V

Undervoltage

Alarm Relay

Trigger

11.0V

11.4V

Undervoltage

Alarm Off Value

12.4V

Undervoltage

Alarm Delay Time

6 seconds

1) Multiply all voltage values by a factor of 2, 3 or 4 for respectively 24V, 36V and 48V systems

When different charge program parameters are desired, the Custom (USE) battery type can be

selected. For further parameter explanations or info on how to create a Custom charge program,

please download the Omnicharge Solar user manual from our website.

CAUTION

Invalid battery type settings can cause serious damage to your batteries and/or connected

battery loads. Always consult your battery’s documentation for the correct charge voltage

settings.

3.2 Battery type selection and solar charger reset

The battery type can be changed in three ways. This can be done using the setup button inside the

connection compartment of the solar charger, by using the control display on the front panel or by

using the TBS Dashboard Mobile app. In this installation manual we will only explain the setup

button method. The two other methods will be explained in the Omnicharge Solar user manual that

can be downloaded from our website.

WARNING

When using the internal setup button to change the battery type, please make sure that

the PV array is completely disconnected from the solar charger.

To enter the battery type setup mode using the setup button, it must be pressed for at least 8

seconds. After this 8 seconds the battery type LED starts flashing and the setup button can be

released. Each time the setup button is pressed again, the color of the battery type LED will change

according to the table shown in chapter 3.1. Once the desired battery type color has been reached,

the setup button must be pressed for 8 seconds again to save the new setting. This new setting is

also saved automatically when the setup button has not been touched for more than 15 seconds.

The internal setup button can also be used to reset the solar charger completely to factory default

settings. To do this, the setup button needs to be pressed for at least 20 seconds. A successful

factory reset is confirmed once all three LEDs shortly start to flash in red. Then the setup button can

be released.

3.3 Connecting the PV panels

When the battery connection and setup has been completed, it is time connect the PV panels to the

solar charger (see chapter 2.3 for details). Provided that the PV panel array can supply and maintain

a voltage that is at least 2V higher than the battery voltage, the solar charger will start the starting

process. This process can be monitored by the PV array LED indicator (left side LED) which will now

also be lit.

Please see the table below for various states of the PV array indicator LED:

PV array LED indicator mode

Charge state

Steady on

MPPT charging (Bulk)

Slow flashing

Absorption charging

Single flashing

Float charging

Quick flashing

Equalize charging

Double flashing

Current limited charging (PV overpower)

Off

No charging

4. TECHNICAL SPECIFICATIONS

Parameter

OCS 150-60

OCS 250-70

System voltage

12Vdc / 24Vdc / 36Vdc / 48Vdc

Maximum charge current1)

60A

70A

Self consumption

0.54W

Battery voltage range

9.0 – 64.0Vdc

Max. PV open circuit voltage

150Vdc

250Vdc

Max. PV short circuit current

50A

40A

MPPT voltage range

Vbatt + 2 up to 120Vdc

Vbatt + 2 up to 180Vdc

Max. PV input power 12V

800W

920W

24V

1600W

1840W

36V

2400W

2760W

48V

3200W

3680W

Charge characteristic

IUoUo, intelligent 3-stage, temp. compensated

Supported battery types2)

Flooded / Gel / AGM / LiFePo4 / Custom (user defined)

Maximum conversion efficiency

98%

Maximum MPPT efficiency

99%

LED indicators

Charge mode, Battery state and Battery type

Display

Yes (detachable for remote use)

Battery temperature sensor

Included

Alarm relay

Yes (10A @ 230Vac or 30Vdc)

Cooling

Natural convection (no fan)

Protections

Battery and PV reverse polarity, output short circuit

and over temperature

Operating temperature range

-35°C ... +60°C

Storage temperature range

-40°C … +80°C

Communication

Through Dashboard Mobile app (iOS and Android)

Connections (PV + Battery)

Screw terminals (35mm2 / 2 AWG)

Dimensions (HxWxD)

266x194x119mm

Weight

3.6kg

Protection class

IP32 (mounted in upright position)

Standards

EMC: 2014/30/EU, Safety: EN62109-1, Functionality

EN62509-1 and RoHS: 2011/65/EU

Note : the given specifications are subject to change without notice.

1) Maximum output current tolerance is +/-5%. Automatic output current derating at Tambient > 45°C. Maximum output current is

programmable via Dashboard Mobile app.

2) Selectable by setup button, display on solar charger or via Dashboard Mobile app

Please act according to your local rules and do not dispose of your old products

with your normal household waste. The correct disposal of your old product

will help prevent potential negative consequences for the environment and

human health.

5. WARRANTY CONDITIONS

TBS Electronics (TBS) warrants this product to be free from defects in workmanship or

materials for 24 months from the date of purchase. During this period TBS will repair the

defective product free of charge. TBS is not responsible for any costs of the transport of

this product.

This warranty is void if the product has suffered any physical damage or alteration, either

internally or externally, and does not cover damage arising from improper use, or from

use in an unsuitable environment.

This warranty will not apply where the product has been misused, neglected, improperly

installed or repaired by anyone other than TBS. TBS is not responsible for any loss,

damage or costs arising from improper use, use in an unsuitable environment, improper

installing of the product and product malfunctioning.

Since TBS cannot control the use and installation (according to local regulations) of their

products, the customer is always responsible for the actual use of these products. TBS

products are not designed for use as critical components in life support devices or

systems, that can potentially harm humans and/or the environment. The customer is

always responsible when implementing TBS products in these kind of applications. TBS

does not accept any responsibility for any violation of patents or other rights of third

parties, resulting from the use of the TBS product. TBS keeps the right to change product

specifications without previous notice.

Examples of improper use are :

- Too high PV input voltage applied

- Reverse connection of PV or battery polarity

- Connecting wrong batteries (too high battery voltages)

- Mechanical stressed enclosure or internals due to harsh handling or incorrect packaging

- Contact with any liquids or oxidation caused by condensation

6. DECLARATION OF CONFORMITY

MANUFACTURER : TBS Electronics BV

ADDRESS : De Marowijne 3

1689 AR Zwaag

The Netherlands

Declares that the following products :

PRODUCT TYPE : MPPT Solar Charge Controller

MODELS : OCS 150-60 and OCS 250-70

Conforms to the requirements of the following Directives of the European Union :

EMC Directive 2014/30/EU

Low voltage Directive 2014/35/EU

RoHS Directive 2011/65/EU

The above product is in conformity with the following harmonized standards :

EMC : EN61326-1:2021

Safety : EN62109-1:2010 and EN62509:2010

INHOUDSOPGAVE

1. VEILIGHEIDSMAATREGELEN ............................................................................................................. 19

2. INSTALLATIE ..................................................................................................................................... 21

2.1 Voorzorgsmaatregelen voor installatie ................................................................................. 21

2.2 Montage ................................................................................................................................ 21

2.3 Bedradingsdetails .................................................................................................................. 22

2.3.1 Andere verbindingen ......................................................................................................... 24

2.3.2 Afneembaar display voor gebruik op afstand .................................................................. 24

3. INBEDRIJFSTELLING .......................................................................................................................... 25

3.1 De accu aansluiten ................................................................................................................ 25

3.2 Accutype selecteren en lader resetten ................................................................................. 26

3.3 De PV-panelen aansluiten ..................................................................................................... 28

4. TECHNISCHE GEGEVENS................................................................................................................... 29

5. GARANTIEVOORWAARDEN .............................................................................................................. 30

6. CONFORMITEITSVERKLARING .......................................................................................................... 30

1. VEILIGHEIDSMAATREGELEN

Hartelijk dank voor uw aankoop van een TBS Electronics (TBS) Omnicharge Solar MPPT Solar Charge

Controller (hierna "product" of "lader" genoemd). Lees deze installatiehandleiding voor informatie

over het correct en veilig installeren van het product. Bewaar deze installatiehandleiding en alle

andere meegeleverde documentatie in de buurt van het product, zodat u deze later kunt

raadplegen. Kijk voor de meest recente revisie van de handleiding in het downloadgedeelte van onze

website.

De installatie-instructies zijn bestemd voor installateurs die voldoende kennis en ervaring hebben in

het installeren van elektrische apparatuur, kennis van de geldende installatievoorschriften en

bewustzijn van de gevaren verbonden aan het uitvoeren van elektrische werkzaamheden en hoe

deze gevaren te beperken.

Dit hoofdstuk bevat belangrijke veiligheidsinformatie voor dit product. Lees ALLE instructies en

waarschuwingen op of bij dit product, en alle relevante hoofdstukken van deze handleiding. Dit

product bevat geen onderdelen die door de gebruiker gerepareerd kunnen worden. Bij het openen

van het product vervalt de garantie.

ALGEMENE WAARSCHUWINGEN

• Bedek of belemmer de ventilatie-openingen niet en/of installeer niet in een te krap

compartiment. Zorg ervoor dat er altijd voldoende vrije ruimte rond het product is

voor ventilatie.

• Schokgevaar! Zonnepanelen kunnen gevaarlijk hoge open klemspanningen

genereren.

• Vermijd binnendringen van vocht. Stel de lader nooit bloot aan sneeuw, water, etc.

• Explosiegevaar! Gebruik dit product niet in de buurt van ontvlambare dampen of

gassen.

• Controleer na het uitpakken het product op mechanische schade. Gebruik het

product nooit als de behuizing zichtbare schade vertoont door ruwe behandeling

of als het per ongeluk is gevallen. Raadpleeg uw lokale handelaar voor meer

informatie.

• Monteer dit product niet in een openbaar toegankelijke ruimte. Uit de buurt van

kinderen houden!

• Zorg er bij de installatie of het onderhoud van dit product altijd voor dat de ingang

van het zonnepaneel spanningsloos is door ofwel de geadviseerde dubbelpolige

stroomonderbreker in de PV-leiding te openen of door de zonnepanelen tegen

licht te beschermen door ze af te dekken

• Raak nooit niet geïsoleerde draadeinden aan en gebruik altijd geïsoleerd

gereedschap tijdens de installatie en het onderhoud van dit product

• Gebruik dit product alleen voor de aangegeven toepassing

WAARSCHUWINGEN VOOR ACCU'S

• Wanneer u werkzaamheden aan elektrische apparatuur of loodzuuraccu’s

uitvoert, zorg er voor dat er een ander persoon in de buurt aanwezig is in geval

van nood

• Bestudeer en volg alle specifieke voorzorgsmaatregelen van de fabrikant van de

accu bij installatie, gebruik en onderhoud van de accu die op de lader is

aangesloten

• Draag oogbescherming en veiligheidshandschoenen

• Raak uw ogen niet aan tijdens het installeren of onderhouden van accu‘s

• Houd schoon water en zeep bij de hand voor het geval accuzuur in contact komt

met de ogen. Als dit gebeurt, moet u het onmiddellijk gedurende minstens 15

minuten met water en zeep schoonmaken en medische hulp inroepen.

• Accu's kunnen explosieve gassen produceren. Rook NIET en houd geen open

vonken of vuur in de buurt van het systeem.

• Probeer nooit om een beschadigde, bevroren of niet-oplaadbare accu op te laden

• Zorg dat er geen metalen gereedschap of voorwerp op de accu valt. Dit kan een

vonk of kortsluiting veroorzaken die door de accu of een ander elektrisch

gereedschap gaat, waardoor een explosie kan ontstaan.

OPGELET

GEBRUIKSBEPERKINGEN

Niet gebruiken in combinatie met life-support systemen of andere medische apparatuur of

apparaten

Deze acculader mag niet worden gebruikt door personen met beperkte fysieke of mentale

mogelijkheden of die gebrek aan kennis en ervaring hebben. Dit product mag niet worden

bediend of gebruikt door kinderen.

Page is loading ...

tbs electronics OCS 250-70 Owner's manual

Brand: tbs electronics

Model: OCS 250-70

Category: Rechargeable batteries

Type: Owner's manual

Download PDF

report

in other languages

français: tbs electronics OCS 250-70 Le manuel du propriétaire
español: tbs electronics OCS 250-70 El manual del propietario
Deutsch: tbs electronics OCS 250-70 Bedienungsanleitung
Nederlands: tbs electronics OCS 250-70 de handleiding

tbs electronics OCS 250-70 Owner's manual

tbs electronics OCS 250-70 Owner's manual

in other languages

Related papers

Other documents